BUSCADOR RECOLECTA

[EN] This is the experimental dataset used in the paper “Biotribocorrosion of CoCr Surfaces Using Hyaluronic Acid functionalized with Graphene Oxide nanoadditive as hybrid lubricants", that include tribocorrosion and electrochemical impedance tests. Tribocorrosion tests were carried out in a pin-on-disk tribometer. The experiments were conducted under a normal load of 5 N, a rotational speed of 120 rpm, following a circular sliding path with a radius of 7 mm and covering a total sliding of 15,000 meters. The dataset includes the experimental results of the tribocorrosion behaviour of CoCr surfaces immersed in the next lubricant media: 0.3 wt% hyaluronic acid (CoCr_bola_CoCr_HA1 and 2); 0.4 wt.% graphene oxide (CoCr_bola_CoCr_GO1, -2 and -3); 0.3 wt.% HA + 0.008 wt.% GO (CoCr_bola_CoCrHA3OG2%-1 and -2): 0.3 wt.% HA + 0.016 wt.% GO (CoCr_bola_CoCrHA3OG4%-1, -2 and -3); 0.3 wt.% HA + 0.032 wt.% GO (CoCr_bola_CoCrHA3OG8%-1 and -2). Electrochemical impedance spectroscopy measurements of CoCr surfaces in 0.3 wt.% HA + 0.016 wt.% GO was carried out for 7 days. Impedance tests were performed in a three-electrode electrochemical cell with the modified CoCr surfaces acting as the working electrode, a Pt wire acting as counter electrode, and Ag/AgCl (3 M KCl) as a reference electrode. A Gamry potentiostat/galvanostat was used to generate a sinusoidal wave of 10 mV amplitude in the frequency range 100 kHz to 1 mHz, logarithmically spaced by 5 points/decade, which was applied at the corrosion potential Ecorr. This data set includes the results of the coefficient of friction and electrochemical impedance data obtained for CoCr surfaces immersed in the previously described lubricant media. COF files are composed of 6 columns: force, temperature, revolutions, COF, sliding and time. Nyquist impedance files are composed of 3 columns: frequency, real impedance (Z') and imaginary impedance (Z''). Bode impedance files are composed of 3 columns: frequency, Impedance modulus (Z) and phase angle (Phase). All files are in open extension such as .asc and are protected by a Creative Commons Attribution 4.0 International (CC BY 4.0) licence., [ES] Este es el conjunto de datos experimentales utilizado en el artículo “Biotribocorrosión de superficies de CoCr utilizando ácido hialurónico funcionalizado con nano-aditivo de óxido de grafeno como lubricantes híbridos”, el cual incluye ensayos de tribocorrosión y de impedancia electroquímica. Los ensayos de tribocorrosión se realizaron en un tribómetro tipo pin-on-disk. Los experimentos se llevaron a cabo bajo una carga normal de 5 N, con una velocidad de rotación de 120 rpm, siguiendo una trayectoria circular de deslizamiento con un radio de 7 mm, y alcanzando un deslizamiento total de 15 000 metros. El conjunto de datos incluye los resultados experimentales del comportamiento a tribocorrosión de superficies de CoCr inmersas en los siguientes medios lubricantes: 0,3 % en peso de ácido hialurónico (CoCr_bola_CoCr_HA1 y 2); 0,4 % en peso de óxido de grafeno (CoCr_bola_CoCr_GO1, -2 y -3); 0,3 % en peso de HA + 0,008 % en peso de GO (CoCr_bola_CoCrHA3OG2%-1 y -2); 0,3 % en peso de HA + 0,016 % en peso de GO (CoCr_bola_CoCrHA3OG4%-1, -2 y -3); 0,3 % en peso de HA + 0,032 % en peso de GO (CoCr_bola_CoCrHA3OG8%-1 y -2). Las medidas de espectroscopía de impedancia electroquímica (EIS) de las superficies de CoCr en 0,3 % en peso de HA + 0,016 % en peso de GO se realizaron durante 7 días. Los ensayos de impedancia se efectuaron en una celda electroquímica de tres electrodos, donde: la superficie modificada de CoCr actuó como electrodo de trabajo, un hilo de platino (Pt) se utilizó como contraelectrodo, y un electrodo de referencia Ag/AgCl (3 M KCl). Se empleó un potenciostato/galvanostato Gamry para generar una onda sinusoidal de 10 mV de amplitud, en un rango de frecuencias de 100 kHz a 1 mHz, distribuidas logarítmicamente con 5 puntos por década, aplicadas en el potencial de corrosión (Ecorr). Este conjunto de datos incluye los resultados del coeficiente de fricción (COF) y los datos de impedancia electroquímica obtenidos para las superficies de CoCr inmersas en los medios lubricantes descritos anteriormente. Los archivos de COF están compuestos por 6 columnas: fuerza, temperatura, revoluciones, COF, deslizamiento y tiempo. Los archivos de impedancia de Nyquist contienen 3 columnas: frecuencia, impedancia real (Z’) e impedancia imaginaria (Z’’). Los archivos de impedancia de Bode contienen 3 columnas: frecuencia, módulo de impedancia (|Z|) y ángulo de fase (Phase). Todos los archivos se encuentran en formato abierto (.asc) y están protegidos por una licencia Creative Commons Attribution 4.0 International (CC BY 4.0)., [EN] This is the experimental dataset used in the paper “Biotribocorrosion of CoCr Surfaces Using Hyaluronic Acid functionalized with Graphene Oxide nanoadditive as hybrid lubricants". The article includes the experimental results of the tribocorrosion behaviour of CoCr surfaces immersed in the next lubricant media: 0.3 wt% hyaluronic acid (CoCr_bola_CoCr_HA1 and 2); 0.4 wt.% graphene oxide (CoCr_bola_CoCr_GO1, -2 and -3); 0.3 wt.% HA + 0.008 wt.% GO (CoCr_bola_CoCrHA3OG2%-1 and -2): 0.3 wt.% HA + 0.016 wt.% GO (CoCr_bola_CoCrHA3OG4%-1, -2 and -3); 0.3 wt.% HA + 0.032 wt.% GO (CoCr_bola_CoCrHA3OG8%-1 and -2). Subsequently, electrochemical impedance spectroscopy measurements of CoCr surfaces in 0.3 wt.% HA + 0.016 wt.% GO was carried out for several days. This data set includes the results of the coefficient of friction and electrochemical impedance data obtained for CoCr surfaces immersed in the previously described lubricant media., [ES] Este es el conjunto de datos experimentales utilizado en el artículo “Biotribocorrosión de superficies de CoCr utilizando ácido hialurónico funcionalizado con nano-aditivo de óxido de grafeno como lubricantes híbridos”. El artículo incluye los resultados experimentales del comportamiento tribocorrosivo de superficies de CoCr inmersas en los siguientes medios lubricantes: 0,3 % en peso de ácido hialurónico (CoCr_bola_CoCr_HA1 y 2); 0,4 % en peso de óxido de grafeno (CoCr_bola_CoCr_GO1, -2 y -3); 0,3 % en peso de HA + 0,008 % en peso de GO (CoCr_bola_CoCrHA3OG2%-1 y -2); 0,3 % en peso de HA + 0,016 % en peso de GO (CoCr_bola_CoCrHA3OG4%-1, -2 y -3); 0,3 % en peso de HA + 0,032 % en peso de GO (CoCr_bola_CoCrHA3OG8%-1 y -2). Posteriormente, se realizaron ensayos de espectroscopía de impedancia electroquímica (EIS) de las superficies de CoCr en 0,3 % en peso de HA + 0,016 % en peso de GO durante varios días. Este conjunto de datos incluye los resultados del coeficiente de fricción y los datos de impedancia electroquímica obtenidos para las superficies de CoCr inmersas en los medios lubricantes descritos anteriormente., Spanish Ministry of Science, Innovation and Universities [RTI2018-101506-B-C31], Peer reviewed

This dataset collects 1,433 bibliographic references related to Spanish architecture during the Franco's dictatorship (1939-1975). The research was focused on news of Spanish Architecture abroad, including academic journals, architectural press, conference proceedings, books, book chapters, magazines and newspapers, but it excludes the Spanish media. All references were tagged including names of architects, buildings, types of buildings and cities. The database is delivered in three file formats (BibTeX, RIS and Zotero RDF), which are compatible with several reference managers as Zotero, Mendeley, EndNote or RefWorks. This dataset was produced by the R&D project “Spanish architecture in international communication media: Publications, exhibitions, congresses (First part: 1940-1975)”. Three ways were used to find the news: Firstly, systematic research was done using architectural databases as Avery Index to Architectural Periodicals, JSTOR or ProQuest Periodicals Index Online; secondly, the most influential architectural magazines were revised in paper (The Architectural Review, Architectural Forum, Casabella continuità, Domus or L’Architecture d’Aujourd’hui); and thirdly, some authors and works were studied following bibliographical references published in their monographs.

This dataset contains data from a population-representative survey examining various factors relating to digital exclusion (particularly digital mobility exclusion). The survey was conducted with 423 adult participants in the Netherlands in 2020 and 2021. This dataset is part of a series of 5 datasets which used the same questionnaire (translated into different languages) in different countries in Europe.

Biomechanical data on the strength of Cerebral Bridging Veins (CBVs), a study funded by La Marató de TV3 (2020-2021). Data on maximum axial force on the tested specimens, strain rate of the test, and the relationship between the two are examined and the probability distributions for the sample are obtained. Data set used for the article "Injury metrics for assessing the risk of acute subdural hematoma in traumatic events" (2021), published in IJERPH ( ISSN: 1660-4601, Basel, Switzerland, MDPI), Project: ``Age Effects on Traumatic Brain Injuries'' funded by Fundació La Marató de TV3, Barcelona, No. Grant 289/C/2017, 201704.30.

Measurements of the water surface elevation were taken close to the wavemaker, along the sloping foreshore and at the dike toe location by resistance type wave gauges. The overtopping flow properties thickness and velocity were measured by ultra-sonic distance sensors and high-speed cameras. Due to its large storage size, the whole set of data is provided on request., The experimental data refer to physical model tests carried out in 2019 from May to December at the wave flume CIEMito of the Maritime Engineering Laboratory (LIM) of the Universitat Politècnica de Catalunya – BarcelonaTech (UPC). The experiments aimed at characterizing the flow characteristics associated to the maximum individual overtopping volumes, due to specific storm events with different return periods. Specifically, the experiments focused on the measurements of overtopping volumes and discharges, in order to find the relation between these parameters with the corresponding overtopping flow velocities and overtopping flow depth, when the maximum overtopping event occurs on a dike during a sea state. A model geometry comprised of a sloping beach, a sloping dike and promenade was built into the CIEMito flume.

Data obtained from Computational Aeroacoustic simulation of Curle and F.WH analogies with OpenFoam., This dataset includes the results of the aeroacoustics field of a tandem cylinder calculated using Curle's and F-WH analogy with OpenFOAM. The sound levels are measured as Power Spectral Density (PSD). The temporal acoustic pressure data is also included.

Anàlisis geoquímiques i fotos de visu i microscòpia de les mostres que integren la col·lecció de geostandards del Museu de Geologia Valentí Masachs (UPC Manresa). Análisis geoquímicas y fotos de visu y microscopio de las muestras que integran la colección de geostandares del Museo de Geología Valentí Masachs (UPC Manresa). Geochemical analyses and hand and microscopy pictures of the samples belonging to the geostandards collection of the Valenti Masachs Geology Museum (UPC Manresa). Analyses géochimiques et photographies au microscope et visu des échantillons qui forment la collection de geostandards du Musée de Géologie Valentí Masachs (UPC Manresa).

The data refer to an experimental campaign carried out to characterize the forces involved in the failure of the Pont del Petroli (Badalona, Catalonia) due to the storm Gloria happened in the night of the 20 January 2020. The experiments were carried out in the CIEM (Canal d’Investigació i Experimentació Marítima) wave flume in the Laboratory of Maritime Engineering of the UPC (Universitat Politecnica de Catalunya - BarcelonaTech, Barcelona, Catalonia)., Data include measurements of water surface elevation along the wave flume and wave loading (forces + pressures) on elements of the pier. Both raw and post-processed data are provided.

The data base is related to the High Pressure Grinding Rolls (HPGR) modelling. This data was generated in a HPGR manufacturer pilot plant in Freiberg, Germany, and represents the particle size distribution measurement of the feed and the product of the milling reactor, and the calculation of some material features, as the moisture or the density. This data is necessary for the correct modelization of the comminution in a HPGR, and it can be used for different mathematical models., A model for High Pressure Grinding Rolls (HPGR) was developed in this work based on the widely used Population Balance Model (PBM). This approach uses a variety of different functions one of which is the breakage distribution function. The methodology to determine the function parameters is presented and using these values, the model was compared with real processed materials from an HPGR pilot plant, with tungsten ore as the test material. The results of the model parameter determination, and the product of the comminution in the HPGR, showed the dependency of material breakage on the material characteristics, and on the operative and process conditions. The model presented is reasonably robust, showing less error than the 3.0 Root Mean Square Error when compared with a heterogeneous feed particle size distribution material. The operational gap was also studied, and its dependency on the feed particle size, porosity, moisture, and specific pressing force was proven.

Data include the active (kW) and reactive (kvar) power for the pilot area of H2020 RESOLVD project, each item in one column and with a time step of one hour and one year length.