Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Experimental FIA Methodology Using Clock and Control Signal Modifications under Power Supply and Temperature Variations

  • Potestad-Ordoñez, Francisco E.
  • Tena-Sánchez, Erica
  • Mora-Gutiérrez, J. M.
  • Valencia-Barrero, M.
  • Jiménez-Fernández, Carlos J.
The security of cryptocircuits is determined not only for their mathematical formulation, but for their physical implementation. The so-called fault injection attacks, where an attacker inserts faults during the operation of the cipher to obtain a malfunction to reveal secret information, pose a serious threat for security. These attacks are also used by designers as a vehicle to detect security flaws and then protect the circuits against these kinds of attacks. In this paper, two different attack methodologies are presented based on inserting faults through the clock signal or the control signal. The optimization of the attacks is evaluated under supply voltage and temperature variation, experimentally determining the feasibility through the evaluation of different Trivium versions in 90 nm ASIC technology implementations, also considering different routing alternatives. The results show that it is possible to inject effective faults with both methodologies, improving fault efficiency if the power supply voltage decreases, which requires only half the frequency of the short pulse inserted into the clock signal to obtain a fault. The clock signal modification methodology can be extended to other NLFSR-based cryptocircuits and the control signal-based methodology can be applied to both block and stream ciphers, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Analysis of the FO Transformation in the Lattice-Based Post-Quantum Algorithms

  • González de la Torre, Miguel Ángel
  • Hernández Encinas, Luis
  • Queiruga Dios, Araceli
20 páginas, 6 tablas, Newer variants of the Fujisaki¿Okamoto transformation are used in most candidates of the third round of the NIST Post-Quantum Cryptography standardization call in the category of public key encryption schemes. These transformations are applied to obtain a highly secure key encapsulation mechanism from a less secure public key encryption scheme. Furthermore, there are five candidates (three finalists and two alternatives) that passed to the third round of the process and whose security is based in lattice problems. This work analyzes the different ways in which the lattice-based candidates of the NIST call apply the Fujisaki¿Okamoto transformation and the particularities of each application. The study of such differences and their repercussion in the design of the proposals will allow a better understanding of the algorithms. Moreover, we propose a modification of the Kyber algorithm¿the only public key encryption candidate established as a PQC standard by NIST in its more recent publication¿in order to avoid the re-encryption in the decapsulation algorithm and, in this way, to reduce the side channel attacks vulnerability., This work was supported in part by ORACLE Project, with reference PCI2020-120691-2, funded by MCIN/AEI/10.13039/501100011033, and European Union “NextGenerationEU/PRTR” and in part by the Spanish State Research Agency (AEI) of the Ministry of Science and Innovation (MCIN), project P2QProMeTe (PID2020-112586RB-I00/AEI/10.13039/501100011033), and in part by the EU Horizon 2020 research and innovation programme, project SPIRS (Grant Agreement No. 952622)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

On-line evaluation and monitoring of security features of an RO-based PUF/TRNG for IoT devices

  • Rojas-Muñoz, Luis Felipe
  • Sánchez-Solano, Santiago
  • Martínez-Rodríguez, Macarena Cristina
  • Brox, Piedad
This article belongs to the Special Issue Validation Methods in IoT Systems: Security, Performance and Safety., The proliferation of devices for the Internet of Things (IoT) and their implication in many activities of our lives have led to a considerable increase in concern about the security of these devices, posing a double challenge for designers and developers of products. On the one hand, the design of new security primitives, suitable for resource-limited devices, can facilitate the inclusion of mechanisms and protocols to ensure the integrity and privacy of the data exchanged over the Internet. On the other hand, the development of techniques and tools to evaluate the quality of the proposed solutions as a step prior to their deployment, as well as to monitor their behavior once in operation against possible changes in operating conditions arising naturally or as a consequence of a stress situation forced by an attacker. To address these challenges, this paper first describes the design of a security primitive that plays an important role as a component of a hardware-based root of trust, as it can act as a source of entropy for True Random Number Generation (TRNG) or as a Physical Unclonable Function (PUF) to facilitate the generation of identifiers linked to the device on which it is implemented. The work also illustrates different software components that allow carrying out a self-assessment strategy to characterize and validate the performance of this primitive in its dual functionality, as well as to monitor possible changes in security levels that may occur during operation as a result of device aging and variations in power supply or operating temperature. The designed PUF/TRNG is provided as a configurable IP module, which takes advantage of the internal architecture of the Xilinx Series-7 and Zynq-7000 programmable devices and incorporates an AXI4-based standard interface to facilitate its interaction with soft- and hard-core processing systems. Several test systems that contain different instances of the IP have been implemented and subjected to an exhaustive set of on-line tests to obtain the metrics that determine its quality in terms of uniqueness, reliability, and entropy characteristics. The results obtained prove that the proposed module is a suitable candidate for various security applications. As an example, an implementation that uses less than 5% of the resources of a low-cost programmable device is capable of obfuscating and recovering 512-bit cryptographic keys with virtually zero error rate., This research was supported in part by the SPIRS Project with Grant Agreement No. 952622 under the EU H2020 research and innovation programme and the ARES Project PID2020-116664RB-100 funded by MCIN/AEI/10.13039/501100011033 and the EU NextGeneration EU/PRTR. M.C.M.R. holds a postdoc fellowship from the Andalusia Government with support from PO FSE of EU., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Timing-attack-resistant acceleration of NTRU round 3 encryption on resource-constrained embedded systems

  • Camacho-Ruiz, Eros
  • Martínez-Rodríguez, Macarena Cristina
  • Sánchez-Solano, Santiago
  • Brox, Piedad
This article belongs to the Special Issue Feature Papers in Hardware Security II., The advent of quantum computing with high processing capabilities will enable brute force attacks in short periods of time, threatening current secure communication channels. To mitigate this situation, post-quantum cryptography (PQC) algorithms have emerged. Among the algorithms evaluated by NIST in the third round of its PQC contest was the NTRU cryptosystem. The main drawback of this algorithm is the enormous amount of time required for the multiplication of polynomials in both the encryption and decryption processes. Therefore, the strategy of speeding up this algorithm using hardware/software co-design techniques where this operation is executed on specific hardware arises. Using these techniques, this work focuses on the acceleration of polynomial multiplication in the encryption process for resource-constrained devices. For this purpose, several hardware multiplications are analyzed following different strategies, taking into account the fact that there are no possible timing information leaks and that the available resources are optimized as much as possible. The designed multiplier is encapsulated as a fully reusable and parametrizable IP module with standard AXI4-Stream interconnection buses, which makes it easy to integrate into embedded systems implemented on programmable devices from different manufacturers. Depending on the resource constraints imposed, accelerations of up to 30–45 times with respect to the software-level multiplication runtime can be achieved using dedicated hardware, with a device occupancy of around 5%., This research was supported in part by the SPIRS Project with Grant Agreement No. 952622 under the EU H2020 research and innovation programme and the ARES Project PID2020-116664RB-100 funded by MCIN/AEI/10.13039/501100011033 and the NextGenerationEU/PRTR. M.C.M.-R. holds a Postdoc fellowship from the Andalusia Government with support from PO FSE of EU. E.C.-R. is supported by the FPU20/03008 predoc grant from the Spanish government., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Gate-level design methodology for side-channel resistant logic styles using TFETs

  • Delgado-Lozano, Ignacio M.
  • Tena-Sánchez, Erica
  • Núñez, Juan
  • Acosta, Antonio J.
The design of secure circuits in emerging technologies is an appealing area that requires new efforts and attention as an effective solution to secure applications with power constraints. This letter deals with the optimized design of differential power analysis (DPA)-resilient hiding-based techniques, using tunnel field-effect transistors (TFETs). Specifically, proposed TFET implementations of dual-precharge-logic primitives optimizing their computation tree in three different ways are applied to the design of the PRIDE 4-bit substitution box, the most vulnerable block of the PRIDE lightweight cipher. The performance of simulation-based DPA attacks on the proposals has shown spectacular results in security gain (34 out of 48 attacks fail for optimized computation trees in TFET technology) and power reduction ( ×25 ), compared to their CMOS-based counterparts in 65 nm, which is a significant advance in the development of secure circuits with TFETs., This work was partially funded by the Spanish Government with support from FEDER under Projects TEC2017-87052-P and PID2020-116664RB-I00, by Programa Operativo FEDER 2014-2020 and Consejeria de Economia, Conocimiento, Empresas y Universidad de la Junta de Andalucia (Projects US1380876 and US-1380823) and by the SPIRS and SCARE Projects with Grant Agreement No. 952622 and No. 804476, respectively, under the European Union’s Horizon 2020 research and innovation programme, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Gate-level hardware countermeasure comparison against power analysis attacks

  • Tena-Sánchez, Erica
  • Potestad-Ordoñez, Francisco E.
  • Jiménez Fernández, Carlos Jesús
  • Acosta, Antonio J.
  • Chaves, Ricardo
This article belongs to the Special Issue Side Channel Attacks in Embedded Systems., The fast settlement of privacy and secure operations in the Internet of Things (IoT) is appealing in the selection of mechanisms to achieve a higher level of security at minimum cost and with reasonable performances. All these aspects have been widely considered by the scientific community, but more effort is needed to allow the crypto-designer the selection of the best style for a specific application. In recent years, dozens of proposals have been presented to design circuits resistant to power analysis attacks. In this paper, a deep review of the state of the art of gate-level countermeasures against power analysis attacks has been carried out, performing a comparison between hiding approaches (the power consumption is intended to be the same for all the data processed) and the ones considering a masking procedure (the data are masked and behave as random). The most relevant proposals in the literature, 35 for hiding and 6 for masking, have been analyzed, not only by using data provided by proposers, but also those included in other references for comparison. Advantages and drawbacks of the proposals are analyzed, showing quantified data for cost, performance (delay and power), and security when available. One of the main conclusions is that the RSL proposal is the best in masking, while TSPL, HDRL, SDMLp, 3sDDL, TDPL, and SABL are those with the best security performance figures. Nevertheless, a wise combination of hiding and masking as masked_SABL presents promising results., This work was funded by Grant PID2020-116664RB-I00 funded by MCIN/AEI/10.13039/501100011033. Authors want to acknowledge to projects Programa Operativo FEDER 2014-2020 and Consejería de Economía, Conocimiento, Empresas y Universidad de la Junta de Andalucía under Project US-1380823, to the SPIRS (Secure Platform for ICT Systems Rooted at the Silicon Manfacturing Process) Project with Grant Agreement No. 952622 under the European Union’s Horizon 2020 research and innovation programme, to Erasmus+, to COST Action CRYPTACUS, to FCT (Fundação para a Ciência e a Tecnologia, Portugal), to the ERDF (European Regional Development Fund, EU) through the projects FCT: UIDB/50021/2020 and LISBOA-01-0145-FEDER-031901 (PTDC/CCI-COM/31901/2017, HiPErBio) and to Disruptive Sdn seCuRE communicaTIons for eurOpean defeNse, EDIDP-CSAMN-SDN-202-74-DISCRETION., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hardware countermeasures benchmarking against fault attacks

  • Potestad-Ordoñez, Francisco E.
  • Tena-Sánchez, Erica
  • Acosta, Antonio J.
  • Jiménez Fernández, Carlos Jesús
  • Chaves, Ricardo
This article belongs to the Special Issue Side Channel Attacks in Embedded Systems., The development of differential fault analysis (DFA) techniques and mechanisms to inject faults into cryptographic circuits brings with it the need to use protection mechanisms that guarantee the expected level of security. The AES cipher, as a standard, has been the target of numerous DFA techniques, where its security has been compromised through different formulations and types of fault injections. These attacks have shown vulnerabilities of different AES implementations and building blocks. Consequently, several solutions have been proposed that provide additional protection to cover the identified vulnerabilities. In this paper, an extensive analysis has been carried out covering the existing fault injection techniques, the types of faults, and the requirements needed to apply DFA. Additionally, an analysis of the countermeasures reported in the literature is also presented, considering the protection provided, the type of faults considered, and the coverage against fault attacks. The eight different types of fault that allow us to perform DFAs on the AES cipher have been differentiated, as well as the vulnerabilities of the cipher. On the other hand, two comparisons have been made considering frequency penalty vs. area and fault coverage vs. area and frequency overhead. A metric has been proposed to compare the fault coverage of all the proposed solutions. To conclude, a final analysis is presented discussing the key aspects when choosing a particular solution and the possible development of new countermeasures to provide further protection against DFA., This work was funded by Grant PID2020-116664RB-I00 funded by MCIN/AEI/10.13039/501100011033. Authors want to acknowledge to projects Programa Operativo FEDER 2014-2020 and Consejería de Economía, Conocimiento, Empresas y Universidad de la Junta de Andalucía under Project US-1380823, to the SPIRS (Secure Platform for ICT Systems Rooted at the Silicon Manfacturing Process) Project with Grant Agreement No. 952622 under the European Union’s Horizon 2020 research and innovation programme, to Erasmus+, to COST Action CRYPTACUS, to FCT (Fundação para a Ciência e a Tecnologia, Portugal), to the ERDF (European Regional Development Fund, EU) through the projects FCT: UIDB/50021/2020 and LISBOA-01-0145-FEDER-031901 (PTDC/CCI-COM/31901/2017, HiPErBio) and to Disruptive Sdn seCuRE communicaTIons for eurOpean defeNse, EDIDP-CSAMN-SDN-202-74-DISCRETION., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Multi-unit serial polynomial multiplier to accelerate NTRU-based cryptographic schemes in IoT embedded systems

  • Sánchez-Solano, Santiago
  • Camacho-Ruiz, Eros
  • Martínez-Rodríguez, Macarena Cristina
  • Brox, Piedad
This article belongs to the Special Issue Advances in Cybersecurity for the Internet of Things., Concern for the security of embedded systems that implement IoT devices has become a crucial issue, as these devices today support an increasing number of applications and services that store and exchange information whose integrity, privacy, and authenticity must be adequately guaranteed. Modern lattice-based cryptographic schemes have proven to be a good alternative, both to face the security threats that arise as a consequence of the development of quantum computing and to allow efficient implementations of cryptographic primitives in resource-limited embedded systems, such as those used in consumer and industrial applications of the IoT. This article describes the hardware implementation of parameterized multi-unit serial polynomial multipliers to speed up time-consuming operations in NTRU-based cryptographic schemes. The flexibility in selecting the design parameters and the interconnection protocol with a general-purpose processor allow them to be applied both to the standardized variants of NTRU and to the new proposals that are being considered in the post-quantum contest currently held by the National Institute of Standards and Technology, as well as to obtain an adequate cost/performance/security-level trade-off for a target application. The designs are provided as AXI4 bus-compliant intellectual property modules that can be easily incorporated into embedded systems developed with the Vivado design tools. The work provides an extensive set of implementation and characterization results in devices of the Xilinx Zynq-7000 and Zynq UltraScale+ families for the different sets of parameters defined in the NTRUEncrypt standard. It also includes details of their plug and play inclusion as hardware accelerators in the C implementation of this public-key encryption scheme codified in the LibNTRU library, showing that acceleration factors of up to 3.1 are achieved when compared to pure software implementations running on the processing systems included in the programmable devices., This research was supported in part by the SPIRS Project with Grant Agreement No. 952622 under the EU H2020 research and innovation programme and the ARES Project PID2020-116664RB-100 funded by MCIN/AEI/10.13039/501100011033 and the NextGenerationEU/PRTR. M.C.M.R. holds a Postdoc fellowship from the Andalusia Government with support from PO FSE of EU. E.C.R. is supported by the FPU20/03008 predoc grant from the Spanish government., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

True random number generation capability of a ring oscillator PUF for reconfigurable devices

  • Rojas-Muñoz, Luis Felipe
  • Sánchez-Solano, Santiago
  • Martínez-Rodríguez, Macarena Cristina
  • Brox, Piedad
This article belongs to the Special Issue Circuits and Systems of Security Applications., This paper presents the validation of a novel approach for a true-random number generator (TRNG) based on a ring oscillator–physical unclonable function (RO-PUF) for FPGA devices. The proposal takes advantage of the different noise sources that affect the electronic implementation of the RO-PUF to extract the entropy required to guarantee its function as a TRNG, without anything more than minimal changes to the original design. The new RO-PUF/TRNG architecture has been incorporated within a hybrid HW/SW embedded system designed for devices from the Xilinx Zynq-7000 family. The degree of randomness of the generated bit streams was assessed using the NIST 800-22 statistical test suite, while the validation of the RO-PUF proposal as an entropy source was carried out by fulfilling the NIST 800-90b recommendation. The features of the hybrid system were exploited to carry out the evaluation and validation processes proposed by the NIST publications, online and on the same platform. To establish the optimal configuration to generate bit streams with the appropriate entropy level, a statistical study of the degree of randomness was performed for multiple TRNG approaches derived from the different implementation modes and configuration options available on the original RO-PUF design. The results show that the RO-PUF/TRNG design is suitable for secure cryptographic applications, doubling its functionality without compromising the resource–efficiency trade-off already achieved in the design., This research was supported in part by the SPIRS Project with Grant Agreement No. 952622 under the EU H2020 research and innovation programme and the ARES Project PID2020-116664RB-100 funded by MCIN/AEI/10.13039/501100011033 and the EU NextGeneration EU/PRTR. M.C.M.R. holds a postdoc fellowship from the Andalusia Government with support from PO FSE of EU., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Protecting FPGA-Based Cryptohardware Implementations from Fault Attacks Using ADCs

  • Potestad-Ordoñez, Francisco E.
  • Casado-Galán, Alejandro
  • Tena-Sánchez, Erica
The majority of data exchanged between connected devices are confidential and must be protected against unauthorized access. To ensure data protection, so-called cryptographic algorithms are used. These algorithms have proven to be mathematically secure against brute force due to the key length, but their physical implementations are vulnerable against physical attacks. The physical implementation of these algorithms can result in the disclosure of information that can be used to access confidential data. Some of the most powerful hardware attacks presented in the literature are called fault injection attacks. These attacks involve introducing a malfunction into the normal operation of the device and then analyzing the data obtained by comparing them with the expected behavior. Some of the most common methods for injecting faults are the variation of the supply voltage and temperature or the injection of electromagnetic pulses. In this paper, a hardware design methodology using analog-to-digital converters (ADCs) is presented to detect attacks on cryptocircuits and prevent information leakage during fault injection attacks. To assess the effectiveness of the proposed design approach, FPGA-based ADC modules were designed that detect changes in temperature and supply voltage. Two setups were implemented to test the scheme against voltage and temperature variations and injections of electromagnetic pulses. The results obtained demonstrate that, in 100% of the cases, when the correct operating voltage and temperature range were established, the detectors could activate an alarm signal when the cryptographic module was attacked, thus avoiding confidential information leakage and protecting data from being exploited., The authors want to express gratitude for the SPIRS (Secure Platform for ICT Systems Rooted at the Silicon Manufacturing Process) Project, Grant Agreement No. 952622, under the European Union’s Horizon 2020 research and innovation programme; Programa Operativo FEDER 2014-2020 and Consejería de Economía, Conocimiento, Empresas y Universidad de la Junta de Andalucía under project US-1380823; and project grant PID2020-116664RB-I00 funded by MCIN/AEI/10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Structural analysis of code-based algorithms of the NIST post-quantum call

  • González de la Torre, Miguel Ángel
  • Hernández Encinas, Luis
  • Sánchez García, José Ignacio
12 páginas, 4 figuras, 3 tablas., Code-based cryptography is currently the second most promising post-quantum mathematical tool for quantum-resistant algorithms. Since in 2022 the first post-quantum standard Key Encapsulation Mechanism, Kyber (a latticed-based algorithm), was selected to be established as standard, and after that the National Institute of Standards and Technology post-quantum standardization call focused in code-based cryptosystems. Three of the four candidates that remain in the fourth round are code-based algorithms. In fact, the only non-code-based algorithm (SIKE) is now considered vulnerable. Due to this landscape, it is crucial to update previous results about these algorithms and their functioning. The Fujisaki-Okamoto transformation is a key part of the study of post-quantum algorithms and in this work we focus our analysis on Classic McEliece, BIKE and HQC proposals, and how they apply this transformation to obtain IND-CCA semantic security. Since after security the most important parameter in the evaluation of the algorithms is performance, we have compared the performance of the code-based algorithms of the NIST call considering the same architecture for all of them., This work was supported in part by project ORACLE, PCI2020-120691-2, funded by MCIN/AEI/ 10.13039/501100011033, in part by QURSA project TED2021-130369B-C33 funded by MCIN/AEI/10.13039/501100011033, both of them co-funded by the European Union ‘NextGenerationEU’/PRTR, in part by P2QProMeTe (PID2020-112586RB-I00), funded by MCIN/AEI/10.13039/501100011033, and in part by the EU Horizon 2020 research and innovation programme, project SPIRS (grant agreement no. 952622)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hardware-Efficient Configurable Ring-Oscillator-Based Physical Unclonable Function/True Random Number Generator Module for Secure Key Management

  • Sánchez-Solano, Santiago
  • Rojas-Muñoz, Luis Felipe
  • Martínez-Rodríguez, Macarena Cristina
  • Brox, Piedad
The use of physical unclonable functions (PUFs) linked to the manufacturing process of the electronic devices supporting applications that exchange critical data over the Internet has made these elements essential to guarantee the authenticity of said devices, as well as the confidentiality and integrity of the information they process or transmit. This paper describes the development of a configurable PUF/TRNG module based on ring oscillators (ROs) that takes full advantage of the structure of modern programmable devices offered by Xilinx 7 Series families. The proposed architecture improves the hardware efficiency with two main objectives. On the one hand, we perform an exhaustive statistical characterization of the results derived from the exploitation of RO configurability. On the other hand, we undertake the development of a new version of the module that requires a smaller amount of resources while considerably increasing the number of output bits compared to other proposals previously reported in the literature. The design as a highly parameterized intellectual property (IP) module connectable through a standard interface to a soft- or hard-core general-purpose processor greatly facilitates its integration into embedded solutions while accelerating the validation and characterization of this element on the same electronic device that implements it. The studies carried out reveal adequate values of reliability, uniqueness, and unpredictability when the module acts as a PUF, as well as acceptable levels of randomness and entropy when it acts as a true random number generator (TRNG). They also illustrate the ability to obfuscate and recover identifiers or cryptographic keys of up to 4096 bits using an implementation of the PUF/TRNG module that requires only an array of 4×4 configurable logic blocks (CLBs) to accommodate the RO bank., This research was supported in part by the SPIRS Project with Grant Agreement No. 952622 under the EU H2020 research and innovation programme and the ARES Project PID2020-116664RB-100 funded by MCIN/AEI/10.13039/501100011033 and the EU NextGeneration EU/PRTR., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Low-Cost Full Correlated-Power-Noise Generator to Counteract Side-Channel Attacks

  • Tena-Sánchez, Erica
  • Potestad-Ordoñez, Francisco E.
  • Zúñiga-González, Virginia
  • Acosta, Antonio J.
Considerable attention has been given to addressing side-channel attacks to improve the security of cryptographic hardware implementations. These attacks encourage the exploration of various countermeasures across different levels of abstraction, through masking and hiding techniques, mainly. In this paper, we introduce a novel hiding countermeasure designed to mitigate Correlation Power Analysis (CPA) attacks without significant overhead. The new countermeasure interferes with the processed data, minimizing the power correlation with the secret key. The proposed method involves using a Correlated-Power-Noise Generator (CPNG). This study is supported by experimental results using CPA attacks on a SAKURA-G board with a SPARTAN-6 Xilinx FPGA. An Advanced Encryption Standard (AES) cipher with 128/256-bit key size is employed for this purpose. The proposed secure design of AES has an area overhead of 29.04% compared to unprotected AES. After conducting a CPA attack, the acquisition of information about the private key has been reduced drastically by 44.5%., This research received no external funding., Authors want to thank projects Grant PID2020-116664RB-I00 funded by MCIN/AEI/ 10.13039/501100011033, project of “Programa Operativo FEDER 2014-2020 and Consejería de Economía, Conocimiento, Empresas y Universidad de la Junta de Andalucía under Project US-1380823”, the SPIRS (Secure Platform for ICT Systems Rooted at the Silicon Manfacturing Process) Project with Grant Agreement No. 952622 under the European Union’s Horizon 2020 research and innovation programme, and by the Ministry for Digital Transformation and Public Function through grant USECHIP (TSI-069100-2023-001) of PERTE Chip Chair program, funded by European Union–Next Generation EU., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

TinyJAMBU Hardware Implementation for Low Power

  • Fernández-Garcia, Carlos
  • Mora-Gutiérrez, J. M.
  • Jiménez Fernández, Carlos Jesús
In this paper, we present hardware implementations of the lightweight TinyJAMBU cipher with reduced power consumption using a mechanism based on shift register parallelization. The power consumption in digital circuits depends linearly on the switching activity of the logic gates. The parallelization technique reduces the number of switches per clock cycle of the shift registers, which can significantly reduce power consumption. This technique has been applied to the TinyJAMBU cipher, a finalist in the NIST lightweight cryptography standardization process with the lowest resource and power consumption. The implementations we present use the logical parallelization technique in the cipher's NLFSR, which is the basic block of TinyJAMBU, and in the key register. Measurements with data from various post-place and route simulations, performed for the Xilinx 7-Series family of FPGAs, are presented to demonstrate the effectiveness of the proposed technique in reducing power consumption, achieving a reduction of more than 30% in dynamic power consumption compared to the standard implementation, with almost no increase in resource consumption. Therefore, the ciphers hardware implementations proposed in this paper are highly suitable for use as hardware peripherals in applications with severe constraints on available resources and power, such as low-power microcontrollers that are widely used in the IoT field., This work has been funded by Project SPIRS (Secure Platform for ICT Systems Rooted at the Silicon Manufacturing Process) Project with Grant Agreement No. 952622 under the European Union’s Horizon 2020 research and innovation programme; and the authors want to thank project ARES, Grant PID2020-116664RB-I00 funded by MCIN/AEI/10.13039/501100011033; to the Ministry for Digital Transformation and Public Function through grant USECHIP (TSI-069100-2023-001) of PERTE Chip Chair program, funded by European Union – Next Generation EU; and to the VII Own Plan for Research and Transfer of The University of Seville (VII-PPITUS)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hardware-Rooted Device Identity for IoT: Integrating Silicon PUFs and DICE in RISC-V Embedded Systems

  • Sisinni, Silvia
  • Ferro, Lorenzo
  • Bravi, Enrico
  • Navarro Torrero, Pablo
  • Camacho Ruiz, Eros
  • Martínez-Rodríguez, Macarena Cristina
  • Brox, Piedad
  • Lioy, Antonio
The security of Internet of Things (IoT) and embedded systems critically depends on establishing trustworthy, unclonable device identities from the earliest boot stages. Conventional approaches often rely on externally stored secrets, which remain vulnerable to extraction and cloning, or heavyweight hardware modules, which are unsuitable for constrained platforms. In this work, we present a lightweight Hardware Root of Trust (HRoT) architecture that integrates silicon-based Physically Unclonable Functions (PUFs) with the Device Identifier Composition Engine (DICE) directly into the boot ROM of RISC-V embedded systems. Unlike existing RoTs, our design eliminates the need for persistent key storage by generating manufacturer-unknown identities on demand, and it extends trust across the system through DICE-based layered attestation. We further introduce lifecycle-aware mechanisms for identity provisioning, renewal, and secure zeroization, ensuring long-term device trustworthiness. The proposed architecture is implemented and evaluated on the open-source SPIRS RISC-V platform, embedding hardware accelerators for cryptography and PUF-bound secrets. Experimental results demonstrate strong resistance against physical and software attacks, compliance with IEC 62443 SL2+ requirements, robust lifecycle support, and negligible performance overhead (¡1% increase in boot time). By bridging unclonable hardware identities with standardized attestation, this work establishes a scalable and interoperable foundation for secure authentication and continuous trust in IoT and embedded devices., This research was supported in part by the Quantum-oriented Update to Browsers and Infrastructures for the PQ transition (QUBIP) Project with Grant Agreement No. 101119746 under the European Union (EU) Horizon Europe research and innovation programme and in part by the Secure Platform for ICT systems Rooted at the Silicon manufacturing process (SPIRS) Project with Grant Agreement No. 952622 under the EU H2020 research. This work was partially supported by the project SEcurity and RIghts in the CyberSpace (SERICS) (PE00000014) under the Piano Nazionale di Ripresa e Resilienza (PNRR) Ministero dell’Universitá e della Ricerca (MUR) program, funded by the European Union - NextGenerationEU. This publication is also part of the project PNRR-NextGenerationEU (NGEU) which has received funding from the MUR – Decreto Ministeriale (DM) 352/2022., Peer reviewed