Skip to main content

MATERIALES ENERGETICAMENTE EFICIENTES PARA ELECTRONICA Y REFRIGERACION

PID2024-159457OB-C21

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal para la Investigación y el Desarrollo Experimental
Subprogram Subprograma Estatal de Generación de Conocimiento Científico-Técnico y Desarrollo Experimental
Call Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Call year 2024
State Plan 2024-2027 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Large sub-Kelvin Magnetocaloric Effect and Phase Behavior of Gadolinium Nitrate Hexahydrate [Dataset]

  • Gracia, David
  • Ubach I Cervera, Marc
  • Charkiolakis, Emmanouil K.
  • García, Inés
  • Milios, Constantinos J.
  • Evangelisti, Marco
Continuous-wave electron paramagnetic resonance (EPR) measurements on a 1% diluted polycrystalline sample of [Gd@Y(NO3)3]6H2O were recorded using a Bruker Elexys 580 spectrometer operating in X-band (9.715 GHz). The spectrometer was equipped with an Oxford CF900 continuous-flow cryostat, which employs liquid-helium to cool down the sample environment. The microwave power was adjusted to avoid saturation effects. The magnetic field was measured with a Bruker ER035 gaussmeter. Direct-current (DC) magnetic measurements were performed on a polycrystalline powder sample (ca. 5 mg), loaded into a plastic capsule and immobilized with eicosane wax to prevent grain movement. Isothermal magnetization curves were collected in magnetic fields between 0-7 T over the temperature range 2-10 K. DC magnetic susceptibility data were recorded over the same temperature range under a constant applied magnetic field of B=0.1 T. All data obtained were corrected for diamagnetic contributions coming from both the sample holder and eicosane wax. In addition, the complex alternating-current (AC) magnetic susceptibility was measured under zero applied magnetic field over the temperature range 0.05-4 K, using a frequency of 525 Hz and an AC field amplitude of 2·10^{-4} T. A thin pressed polycrystalline pellet (ca. 6 mg) was prepared for these experiments, and susceptibility data were initially recorded in arbitrary units. Absolute values of the real component were obtained by comparison with DC susceptibility data collected with the MPMS-3 in the overlapping temperature range (2-4 K), where dissipative processes are negligible. The imaginary component is reported in arbitrary units. Heat capacity measurements were carried out using the relaxation method in a Quantum Design PPMS equipped with a 3He cryostat, covering temperatures down to 0.4 K under constant magnetic fields from 0 to 7 T. Additional measurements extended to 0.05 K under fields up to 1 T using a Quantum Design PPMS DynaCool with DR module. Samples consisted of thin pressed polycrystalline pellets (ca. 1 mg for 3He and ca. 0.2 mg for DR). In both setups, Apiezon N grease (0.2 mg) was applied to ensure good thermal contact between the sample and the calorimeter platform. Its contribution to the total heat capacity was subtracted using a phenomenological correction. Direct quasi-adiabatic MCE measurements were performed for complete demagnetization processes. For these experiments, a pressed polycrystalline pellet of ca. 5 mg was mounted on a calorimeter platform coated with ca. 0.2 mg of Apiezon N grease to improve thermal coupling. In addition, the MCE was also evaluated indirectly by applying standard thermodynamic relations to the measured magnetization and heat capacity data., We report a comprehensive magnetothermal study of the classical gadolinium salt [Gd(NO3)3]·6H2O at temperatures approaching absolute zero. Despite its long-standing availability as a commercial compound, its magnetocaloric properties have remained unexplored. Using electron paramagnetic resonance, magnetic susceptibility, heat capacity, and direct measurements of the magnetocaloric effect, we reveal that weak dipolar interactions combined with axial crystal-field anisotropy drive antiferromagnetic ordering at T_N = 0.21 K. Remarkably, [Gd(NO3)3]·6H2O exhibits an isothermal magnetic entropy change of -\Delta S_m = 26.1 J / K kg at T = 0.6 K for a modest field variation of Delta-B = 1 T, and an adiabatic temperature change of Delta-T_ad = 5.0 K at T = 1.6 K for the same Delta-B, outperforming many state-of-the-art Gd-based refrigerants. These results provide a reference for understanding magnetocaloric behavior in hydrated salts and highlight the interplay between crystal-field anisotropy and dipolar coupling at ultra-low temperatures., This work was funded by EU (MSCA-DN MolCal, 101119865), MICIU/AEI/10.13039/501100011033/ and ERDF/EU (PID2021-124734OB-C21, PID2024-159457OB-C21, CEX2023-001286-S)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Tetradecanuclear {Ni9Ln5} clusters featuring encapsulated {Ln5} bipyramids: Modular 3d-4f architectures with broad-range magnetocaloric response

  • Tziotzi, Thomais G.
  • Asmargiannaki, Evangelia G.
  • Thamm, Ben
  • Dalgarno, Scott J.
  • Charkiolakis, Emmanouil K.
  • Ubach I Cervera, Marc
  • Gracia, David
  • Evangelisti, Marco
  • Milios, Constantinos J.
Magnetisation data were collected on a QD-MPMS3 SQUID magnetometer equipped with a 7 T magnet. Diamagnetic corrections were applied using Pascal's constants., Heat capacity measurements were carried out on a QD-PPMS equipped with a 9 T magnet and a 3He cryostat, using a thin pressed pellet (ca. 1 mg) of polycrystalline samples of 1 and 3, thermalized by ca. 0.2 mg of Apiezon N grease, whose contribution was subtracted using a phenomenological expression., Crystallographic data for compounds 1 - 3 have been deposited at the CCDC under numbers 2533099 - 2533101, respectively, and can be obtained from https://www.ccdc.cam.ac.uk/structures/., The solvothermal reaction between Ni(HCOO)2.2H2O, 2-aminoisobutyric acid (aibH), Ln(OAc)3·6H2O (Ln = Gd, Y, Dy) and NEt3 in MeOH/MeCN affords the tetradecanuclear [Ni9Ln5(OH)9(aib)12(OAc)x(ΗCOO)y].12MeCN complexes (Ln= Gd, x=6, y=6, 1.12MeCN; Ln= Y, x=6, y=6, 2.12MeCN; Ln= Dy, x=3, y=9, 3.12MeCN) in good yields. All three clusters are isostructural, featuring a trigonal bipyramidal {Ln5} core encapsulated within a triply edge-capped {[NiII3]NiII6} trigonal prism. Magnetic measurements reveal dominant ferromagnetic intermolecular interactions in the Gd and Dy analogues, whereas the Y derivative exhibits weak antiferromagnetic behavior. Magnetothermal and heat-capacity measurements for 1.12MeCN indicate a significant magnetocaloric effect, reaching −∆Sm= 29.0 J kg-1K-1 for full demagnetization from B = 7 T at T = 3.0 K, while sustaining large −ΔSm(T,ΔB) and ΔTad(T,ΔB) responses across an unusually broad temperature range., This work has received support from EU (MSCA-DN MolCal, 101119865), MICIU/AEI/10.13039/501100011033/ and ERDF/EU (PID2024-159457OB-C21, CEX2023-001286-S). CJM and TGT would like to thank the National Recovery and Resilience Plan Greece 2.0 (Award Number TAEDR-0535821), funded by the European Union − NextGenerationEU., CEX2023-001286-S, Figure 5: T1, T2, T3 = temperature for compounds 1, 2 and 3, respectively. x1, x2, x3 = magnetic susceptibility for compounds 1, 2 and 3, respectively. T2fit, x2fit = simulated temperature and susceptibility for compound 2. B = applied magnetic field M2K, M3K = molar magnetization at 2K and 3K, respectively. Bfit, M2Kfit = simulated magnetic field and magnetization at 2K Figure 6: T0, T1T = temperature for zero applied magnetic field and 1T, respectively. C0, C1T = molar heat capacity for zero applied magnetic field and 1T, respectively. T0fit, C0fit = simulated temperature and heat capacity for zero applied magnetic field. Figure 7: TDSmC = temperature for magnetic entropy change (DSm) data calculated from heat capacity (C). DSmC1T = DSm calculated from C for 1T applied magnetic field. TDSmM = temperature for DSm data calculated from magnetization (M). DSmC1T = DSm calculated from M for 1T applied magnetic field. TDTad = temperature for adiabatic temperature change (DTad) data. DTad1T = DTad for 1T applied magnetic field., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Temperature-driven elastocaloric enhancement in liquid crystal elastomers

  • Rojo, Kenneth Roy
  • Cosculluela, Carlos
  • Téllez, Pedro
  • Sánchez-Somolinos, Carlos
  • Evangelisti, Marco
[Description of methods used for collection/generation of data]: Differential scanning calorimetry measurements were performed using DSC Q1000 (TA Instruments) on both the LCE and its precursor. The sample pan utilized for both measurements was the hermetically sealed Tzero aluminum pan (TA Instruments). The heating rate was consistently maintained at 5 °C/min. The temperature modulation parameters were set to a period of 50 seconds and an amplitude of ± 0.663 °C. Before each heating procedure, a 15-minute isothermal interval was applied to allow the equipment to stabilize and reach the designated modulation parameters. Three heat cycles were programmed per measurement with each heat-cool cycle followed by a Newtonian cooling quench. The initial and secondary heat-cool cycles effectively erased the thermal history of the samples. The values presented herein were gathered from the third and final heating cycle. Broadband Dielectric Spectroscopy (BDS) measurement of the prepared LCE material was taken using the Alpha-Beta Impedance Analyzer (Novocontrol). The measurement frequency range was 10^[-1] to 10^[7] Hz. The sample was positioned between 20-mm diameter gold-plated electrodes and subsequently loaded into the Active Sample Cell (Novocontrol) sample stage. The sample was proportioned with a larger diameter than the electrodes to ensure an overhang and prevent short-circuit. The root mean square of the applied AC voltage was 1.0 Vrms. To investigate the polymer dynamics, dielectric measurements were conducted in isothermal mode with a temperature step value of 5 °C/min from -120 to 100 °C/min. The temperature control of each isothermal measurement was maintained by the Quatro Cryosystem (Novocontrol), exhibiting a temperature stability better than ± 0.28$ K. Dynamic mechanical analysis (DMA) measurements were performed using DMA Q800 (TA Instruments) in tension mode. LCE samples were portioned into 25~mm long strips with a width of 2-6 mm. The single-frequency measurement was conducted at a frequency of 1~Hz. The oscillation amplitude was set to 0.37 strain. The sample was initially equilibrated at -100 °C for 5 minutes and then heated up to 70 °C at a heating rate of 2 °C/min. Tensile equipment: A custom-built tensile setup was developed to perform the deformation cycles required for direct measurements of the eC effect. A belt-drive motor provided strain load with an accuracy of ± 0.1 mm. The loading strain rate was set such that the loading strain was reached within 0.2 s, while unloading was performed at the maximum attainable rate of the motor, corresponding to -1200 mm/s. The sample stage was enclosed within a PID-controlled heating chamber to enable precise temperature regulation. The tensile apparatus was housed inside a polystyrene enclosure for temperature regulation, and active cooling was achieved by introducing a controlled nitrogen gas flow into the enclosure. Temperature measurements: Infrared thermography was employed to conduct contact-less temperature measurements. A FLIR A655sc (Teledyne FLIR) with 25°C field of view is pointed towards the thermal window of the polystyrene case. To minimize IR reflections and background noise, the upper surface of the polystyrene enclosure was uniformly covered with black electrical tape. All IR videos were captured at a frame rate of 50 frames per second. The sample temperature was extracted as the mean value of the central third of the visible LCE surface, both in the undeformed and elongated states., [Methods for processing the data]: For elastocaloric measurements, the initial temperature was defined as the time‑equilibrated temperature of the undeformed sample region immediately prior to loading. Following deformation, temperature values were obtained from the corresponding central region of the elongated sample, and after unloading from the central region of the recovered geometry. In cases where partial out‑of‑focus regions arose due to sample bending or delayed geometric recovery, temperature analysis was restricted to the central in‑focus area. The adiabatic temperature change was determined relative to the initial equilibrated temperature preceding each loading or unloading event. For BDS measurements, the characteristic relaxation time of every molecular motion was simulated using either Havriliak-Negami (for cooperative relaxations) or Cole-Cole equation (for local relaxations)., Liquid crystal elastomers exhibit promising elastocaloric behavior, yet all direct measurements reported to date have been restricted to room temperature. Here, we perform variable-temperature direct elastocaloric measurements on an isotropic liquid crystal elastomer using a custom tensile setup coupled with infrared thermography, enabling fast mechanical cycling across a broad temperature range. As temperature decreases from ambient conditions, the elastocaloric response increases markedly, peaking near –3.5 ◦C with adiabatic temperature changes of ∆T+ = 3.94 ◦C and ∆T− = −4.33 ◦C at 60 % strain. By correlating these measurements with a detailed investigation of polymer dynamics, we identify a finite temperature window in which the elastocaloric response is maximized. This optimum arises from kinetic timescale matching between molecular relaxations and the mechanical loading-unloading cycle. These results establish kinetic control as a key factor governing the temperature dependence of elastocaloric performance in liquid crystal elastomers., This work was funded by EU (MSCA-DN MolCal, 101119865), MICIU/AEI/10.13039/501100011033/ and ERDF/EU (PID2024-159457OB-C21, CEX2023-001286-S), Gobierno de Aragón (PROY_E28_24), ERDF/EU and Fondo Social Europeo (DGA E15_20R), CIBER - Consorcio Centro de Investigación Biomédica en Red (CB06/01/00263), Instituto de Salud Carlos III, Ministerio de Ciencia e Innovación., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Reversible low-pressure barocaloric effect from mixed‑phase stabilization in a hybrid cadmium perovskite [Dataset]

  • Charkiolakis, Emmanouil K.
  • Gracia, David
  • Blasco, Javier
  • Cuartero, Vera
  • Popescu, Catalin
  • Liu, Xiaojiao
  • Subías, Gloria
  • Evangelisti, Marco
[Sample preparation and characterization] The layered hybrid organic–inorganic perovskite (C9H19NH3)2CdCl4 (C9CdCl) was synthesized following the procedure described in the associated manuscript. Phase purity was verified by powder X-ray diffraction (PXRD)., [Adiabatic calorimetry] Heat-capacity measurements were performed using an AK-6-25 adiabatic calorimeter (AOZT Termis). Measurements were carried out over the temperature range encompassing the structural phase transitions. The transition entropy and enthalpy changes were determined from the temperature dependence of the heat capacity., [Differential scanning calorimetry] Differential scanning calorimetry (DSC) measurements were conducted using a TA Instruments DSC Q2000 calorimeter equipped with a Refrigerated Cooling System (RCS90) and a standard DSC cell. Approximately 4 mg of sample was sealed in Tzero Aluminum Hermetic pans and measured under a continuous nitrogen flow. Heat-capacity measurements were calibrated using sapphire standards. Additional DSC experiments were performed at different heating and cooling rates to evaluate the kinetic dependence of the phase transitions., [Powder X-ray diffraction] Laboratory PXRD measurements were carried out using a Rigaku D-Max diffractometer with Cu Kα₁,₂ radiation over the 2θ range 2.5–50°. Temperature-dependent PXRD data were collected using a Rigaku variable-temperature stage, allowing in situ measurements between 93 and 573 K., [Synchrotron X-ray powder diffraction] High-resolution synchrotron X-ray powder diffraction (SXRPD) measurements were performed at the MSPD beamline of the ALBA Synchrotron (Spain) and at beamline I15 of Diamond Light Source (United Kingdom). Temperature-dependent and pressure-dependent diffraction patterns were collected to investigate the structural evolution across the phase transitions. At Diamond Light Source, high-pressure diffraction experiments were performed using a high-pressure jump cell enabling continuous pressure variation up to approximately 3.5 kbar. Powder samples were loaded into sealed Kapton capillaries, while pressure was transmitted hydrostatically through deionized water surrounding the capillary. Both isothermal and isobaric diffraction measurements were carried out over the ranges 278–330 K and 0.4–2.0 kbar., [High-pressure calorimetry] Barocaloric measurements were performed using a custom-built high-pressure calorimetric setup incorporating a calorimeter within a Be–Cu pressure cell. A surface-mount resistor served simultaneously as sample holder and temperature sensor, while Daphne 7373 oil was employed as the hydrostatic pressure-transmitting medium. Measurements were conducted in an Oxford Instruments OptistatDN cryostat operating between 77 and 400 K., Pressure‑driven phase transitions provide a means to modulate entropy in solids, although achieving large and reversible caloric responses remains a central challenge. The layered hybrid organic-inorganic perovskite (C9H19NH3)2CdCl4 exhibits two first-order transitions near room temperature that underpin its barocaloric response. High‑pressure calorimetry combined with synchrotron X‑ray diffraction shows that compression stabilizes a mixed‑phase region over a wide pressure-temperature range rather than inducing a complete transformation. Consequently, the effective entropy change decreases with pressure, while a substantial reversible contribution is preserved, yielding reversible entropy and temperature changes of ΔSᵣₑᵥ ≈ 136 J kg⁻1 K⁻1 and ΔTᵣₑᵥ ≈ 17 K for a pressure change of 0.8 kbar. This leads to a refrigerant capacity exceeding 4 kJ kg⁻1 with a favorable coefficient of performance in the low-pressure regime. Notably, the large reversible temperature changes achieved at comparatively low pressures and close to room temperature highlight the potential of this material for solid-state cooling. Overall, these results demonstrate that high caloric performance can be achieved without complete phase transformation, reflecting a trade-off between entropy change and reversibility in soft hybrid lattices., This work was supported by Spanish MICIU/AEI/10.13039/501100011033/ and ERDF/EU (PID2024-159457OB-C21, CEX2023-001286-S). This work was carried out with the support of Diamond Light Source, instrument I15 (proposal CY40151) and ALBA Synchrotron, MSPD beamline (proposal 2024098680). E.K.C. acknowledges financial support from MICIU through a doctoral fellowship (PRE2022-103760). The authors acknowledge the Servicio General de Apoyo a la Investigación from Universidad de Zaragoza., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., No