Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Effect of toluene on siloxane biodegradation and microbial communities in biofilters

  • González Cortés, José Joaquín
  • Lamprea-Pineda, P. A.
  • Valle Gallardo, Antonio
  • Ramírez Muñoz, Martín
  • Van Langenhove, H.
  • Demeestere, K.
  • Walgraeve, C.
The removal of volatile methyl siloxanes (VMS) from landfill biogas is crucial for clean energy utilization. VMS are usually found together with aromatic compounds in landfill biogas of which toluene is the major representative. In the present study, two biofilters (BFs) packed with either woodchips and compost (WC) or perlite (PER) were used to study the (co–) removal of octamethyltrisiloxane (L3) and octamethylcyclotetrasiloxane (D4) from gas in presence and absence of toluene, used as a representative aromatic compound. The presence of low inlet toluene concentrations (315 ±19 – 635 ±80 mg toluene m-3) enhanced the VMS elimination capacity (EC) in both BFs by a factor of 1.8 to 12.6. The highest removal efficiencies for D4 (57.1 ±1.1 %; EC =0.12 ±0.01 gD4 m-3 h-1) and L3 (52.0 ±0.6 %; EC =0.23 ±0.01 gL3 m-3 h-1) were observed in the BF packed with WC. The first section of the BFs (EBRT =9 min), where toluene was (almost) completely removed, accounted for the majority (87.7 ±0.6 %) of the total VMS removal. Microbial analysis revealed the impact of VMS and toluene in the activated sludge, showing a clear selection for certain genera in samples influenced by VMS in the presence (X2) or absence (X1) of toluene, such as Pseudomonas (X1 =0.91 and X2 =12.0 %), Sphingobium (X1 =0.09 and X2 =4.04 %), Rhodococcus (X1 =0.42 and X2 =3.91 %), and Bacillus (X1 =7.15 and X2 =3.84 %). The significant maximum EC values obtained by the BFs (0.58 gVMS m-3 h-1) hold notable significance in a combined system framework as they could enhance the longevity of traditional physicochemical methods to remove VMS like activated carbon in diverse environmental scenarios.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Methane concentration and bacterial communities' dynamics during the anoxic desulfurization of landfill biogas under diverse nitrate sources and hydraulic residence times

  • González Cortés, José Joaquín
  • Quijano Melero, Joaquín
  • Ramírez Muñoz, Martín
  • Cantero Moreno, Domingo
Landfill biogas contains certain amounts of H2S that must be removed in order to prevent both equipment corrosion and SO2 emissions to the atmosphere when burnt. Anoxic desulfurization has been proven to be an eco-friendly and cost-efficient method to remove H2S from biogas. Nevertheless, and despite all the reported benefits, the potential consumption of methane (CH4) during the anoxic desulfurization of landfill biogas is a factor that has not yet been thoroughly investigated. The present study evaluates the microbial composition and methane assimilation activity of three microbial samples obtained when feeding different nitrate sources, namely nitrified landfill leachate (M1) or chemical nitrate (M2, M3) with 10 days (M2) and 1.5 days (M3) hydraulic residence times. The samples were characterized by the prevalence of sulfide oxidizing bacteria [Thiomicrospira (11.4-25.5 %), Family Rhodobacteraceae (9.9-14.3 %), Sulfurimonas (0.34-17.9 %), Thioclava (0-23.5 %) and Arcobacter (0-11.5 %)], as well as the presence of methane oxidizing bacteria [Halomonas (0.2-16.0 %), Methylophaga (0-0.2 %) and Methylophilacea (0-0.1 %)] and heterotrophic bacteria [Lentimicrobium (0.1-9.7 %) and Roseovarius (0.1-1.2 %)]. The highest CH4 assimilation levels were reached under anoxic conditions at 34.0 and 50.1 g CH4 m-3 h-1 using nitrate and nitrite, respectively. The oxygen present in the landfill biogas itself had a detrimental effect on the anoxic bioreactor nitrate removal efficiency. The presence of organic matter in the nitrified influent gave rise to CH4 inside the anoxic desulfurization bioreactors, which resulted in the offsetting of the CH4 oxidation caused by methane-oxidizing bacteria (MOB). © 2023 The Authors.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Biofiltration of gaseous mixtures of dimethyl sulfide, dimethyl disulfide and dimethyl trisulfide: Effect of operational conditions and microbial analysis

  • González Cortés, José Joaquín
  • Lamprea-Pineda, P. A.
  • Ramírez, M.
  • Demeestere, K.
  • Van Langenhove, H.
  • Walgraeve, C.
The efficient removal of volatile sulfur compounds (VSCs), such as dimethyl sulfide (DMS), dimethyl disulfide (DMDS) and dimethyl trisulfide (DMTS), is crucial due to their foul odor and corrosive potential in sewer systems. Biofilters (BFs) offer promise for VSCs removal, but face challenges related to pH control and changing conditions at full scale. Two BFs, operated under acidophilic conditions for 78 days, were evaluated for their performance at varying inlet concentrations and empty bed residence times (EBRTs). BF1, incorporating 4–6 mm marble limestone for pH control, outperformed BF2, which used NaHCO3 in the nutrient solution. BF1 displayed better resilience, maintained a stable pH of 4.6 ± 0.6, and achieved higher maximum elimination capacities (ECmax, 41 mg DMS m− 3 h− 1 (RE 38.3%), 146 mg DMDS m− 3 h− 1 (RE 83.1%), 47 mg DMTS m− 3 h− 1 (RE 93.1%)) at an EBRT of 56 s compared to BF2 (9 mg DMS m− 3 h− 1 (RE 7.1%), 9 mg DMDS m− 3 h− 1 (RE 4.8%) and 11 mg DMTS m− 3 h− 1 (RE 26.6%)). BF2 exhibited pH stratification and decreased performance after feeding interruptions. The biodegradability of VSCs followed the order DMTS > DMDS > DMS, and several microorganisms were identified contributing to VSCs degradation in BF1, including Bacillus (14%), Mycobacterium (11%), Acidiphilium (7%), and Acidobacterium (3%).
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Bioleaching of the α-alumina layer of spent three-way catalysts as a pretreatment for the recovery of platinum group metals

  • Compagnone, María Cristina
  • González Cortés, José Joaquín
  • Yeste Siguenza, María del Pilar
  • Cantero Moreno, Domingo
  • Ramírez Muñoz, Martín
Acid bioleaching of Al by Acidithiobacillus thiooxidans has been explored as an environmentally friendly pretreatment to facilitate the extraction of platinum group metals from spent three-way catalysts (TWC). Biogenic sulfur obtained from desulfurization bioreactors improved the production of acid by A. thiooxidans compared to commercially available elemental sulfur. The lixiviation abilities of bacteria-free biogenic acid and biogenic acid with exponential or stationary phase bacteria were compared against a control batch produced by commercial H2SO4. The maximum Al leaching percentage (54.5%) was achieved using biogenic acids with stationary-phase bacteria at a TWC pulp density of 5% w/v whereas bacteria-free biogenic acid (23.4%), biogenic acid with exponential phase bacteria (21.7%) and commercial H2SO4 (24.7%) showed lower leaching abilities. The effect of different pulp densities of ground TWC (5, 30, and 60% w/v) on Al leaching and bacterial growth was determined. While greater Al leaching yields were obtained at lower TWC pulp density solutions (54.5% at 5% w/v and 2.5% at 60% w/v), higher pulp densities enhanced microbial growth (2.3 × 109 cells/mL at 5% w/v and 9.5 × 1010 cells/mL at 60% w/v). The dissolution of the metal from the solid into the liquid phase triggered the production of biological polymeric substances that were able to absorb traces of both Al (up to 24.80% at 5% w/v) and Pt (up to 0.40% at 60% w/v)., 11 páginas
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Recent advances in biological technologies for anoxic biogas desulfurization.

  • Almengló Cordero, Fernando
  • González Cortés, José Joaquín
  • Ramírez Muñoz, Martín
  • Cantero Moreno, Domingo
Recovery of the energy contained in biogas will be essential in coming years to reduce greenhouse gas emissions and our current dependence on fossil fuels. The elimination of H2S is a priority to avoid equipment corrosion, poisoning of catalytic systems and SO2 emissions in combustion engines. This review describes the advances made in this technology using fixed biomass bioreactors (FBB) and suspended growth bioreactors (SGB) since the first studies in this field in 2008. Anoxic desulfurization has been studied mainly in biotrickling filters (BTF). Elimination capacities (EC) up to 287 gS m-3 h-1 have been achieved, with a removal efficiency (RE) of 99%. Both nitrate and nitrite have been successfully used as electron acceptor. SGBs can solve some operational problems present in FBBs, such as clogging or nutrient distribution issues. However, they present greater difficulties in gas-liquid mass transfer, although ECs of up to 194 gS m-3 h-1 have been reported in both gas-lift and stirred tank reactors. One of the major disadvantages of using anoxic biodesulfurization compared to aerobic biodesulfurization is the need to provide reagents (nitrates and/or nitrites), with the consequent increase in operating costs. A solution proposed in this respect is the use of nitrified effluents, some ammonium-rich effluents nitrified include landfill leachate and digested effluent from the anaerobic digester have been tested successfully. Among the microbial diversity found in the bioreactors, the genera Thiobacillus, Sulfurimonas and Sedimenticola play a key role in anoxic removal of H2S. Finally, a summary of future trends in technology is provided.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Optimization of biogenic sulfur flocculation from an anoxic desulfurization bioreactor using response surface methodology

  • Torres Herrera, Sandra
  • González Cortés, José Joaquín
  • Almengló Cordero, Fernando
  • Yeste Siguenza, María del Pilar
  • Ramírez Muñoz, Martín
  • Cantero Moreno, Domingo
Elemental sulfur is an interesting byproduct obtained in the anoxic biodesulfurization of biogas. However, the colloidal properties of this biogenic elemental sulfur (S0) make its efficient recovery difficult. The present study investigated the flocculation of S0 produced in an anoxic bioreactor for biogas desulfurization using cationic (Sedifloc 40L4 C, Lizaflock 853 M), anionic (Innoflock 201) and non-ionic flocculants (NI-1009) and a coagulant (polyaluminum chloride). Cationic-type flocculants showed the highest flocculation efficiency, which led to its selection for further evaluation using the response surface methodology of the effects and interactions of its dose, stirring speed and pH on the biogenic sulfur flocculation rate. Optimum S0 flocculation conditions were observed using Lizaflock 853 M at a dose of 0.82 mg L−1, a stirring speed of 30 rpm and a pH of 8.0. A S0 flocculation rate of 97.05% was achieved for an initial concentration of 1730 mg S0 L−1. The Zeta potential of the settled sulfur particles increased after the flocculation process. © 2022 The Author(s)
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Development and validation of a sampling and analysis method to determine biogenic sulfur in a desulfurization bioreactor by gas chromatography coupled with a pulsed flame photometric detector (GC-PFPD).

  • Torres Herrera, Sandra
  • González Cortés, José Joaquín
  • Almengló Cordero, Fernando
  • Ramírez Muñoz, Martín
  • Cantero Moreno, Domingo
Suspended biomass bioreactors can be operated to remove H2S from biogas under anoxic conditions and produce elemental sulfur, the commercial value of which has been demonstrated. In the present paper, a novel methodology comprising the optimization of a determination method performed in a gas chromatograph equipped with a pulsed flame photometric detector (GC-PFPD), combined with a simple preparation based on filtration and extraction with toluene, is proposed. The injector temperature and carrier gas flow rate (QHe) values were optimized using a response surface methodology based on a face-centred composite central design. This optimization revealed that the optimum conditions were an injector temperature and carrier gas flow rate of 222°C and 7mLmin-1, respectively. The chromatographic method shows an analysis time of 48min, a detection limit of more than 5.9mgL-1, a relative standard deviation of less than 3.71%, and a sulfur recovery percentage of more than 98%. These values provide excellent linearity and a reasonable concentration range (10-200mgL-1). Finally, a measurement error of 4.45% was obtained when using the present method in a selectivity test. Copyright © 2021 The Authors. Published by Elsevier B.V. All rights reserved., This work has been co-financed by the 2014–2020 ERDF Operational Programme and by the Department of Economy, Knowledge, Business and University of the Regional Government of Andalusia. Project reference: FEDER-UCA18-106138.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Effect of surfactant addition on the biofiltration of siloxane-contaminated gas streams

  • González Cortés, José Joaquín
  • Lamprea-Pineda, Paula
  • Ramírez Muñoz, Martín
  • Van Langenhove, H.
  • Demeestere, K.
  • Walgraeve, C.
Biogas contains low levels of volatile methyl siloxanes (VMS), which are responsible for severe damage to turbines or internal combustion engines during energy recovery. In this study, we investigated the removal of the linear octamethyltrisiloxane (L3) and cyclic octamethylcyclotetrasiloxane (D4) from gas by using two biofilters (BFs) filled with either woodchips and compost (WC) or perlite (PER). To overcome the mass transfer limitation, the addition of a synthetic (Tween 80) and a biological (Quillaja saponin, QS) surfactant on the removal of VMS in both BFs was studied. Tween 80 (added at × 1 critical micelle concentration, CMC) and QS (also at × 1 CMC) enhanced VMS removal in both BFs. Specifically, the performance of both BFs increased from an average VMS elimination capacity (EC) of 0.07 ± 0.04 g VMS m−3 h−1 to 0.24 ± 0.08 g VMS m−3 h−1 (Tween 80) and 0.43 ± 0.02 g VMS m−3 h−1 (QS). However, higher concentrations of Tween 80 ( × 3 CMC) did not further improve VMS removal. The WC BF exhibited a higher maximum EC of 0.63 g VMS m−3 h−1 (0.37 g D4 m−3 h−1 and 0.26 g L3 m−3 h−1), with a VMS RE of 28.4 ± 2.0% (D4 RE = 30.4% and L3 RE = 26.5%). The PER BF obtained a maximum EC of 0.52 g VMS m−3 h−1 (0.28 g D4 m−3 h−1 and 0.23 g L3 m−3 h−1), along with a VMS RE of 32.0 ± 0.8% (D4 RE = 31.2% and L3 RE = 32.8%). The most abundant genera in the WC BF were Mycobacterium (7.5–1.8%), Rhodococcus (1.1–7.2%), and Planctomicrobium (5.1–2.9%). However, given the high microbial diversity present in WC BF and the complex structure of VMS, their removal was most likely due to the joint activity of several microorganisms with VMS-degrading capacity, such as Bacillus (0.58–0.39%), Pseudomonas (0.07–0.04%), Dokdonella (0.50–0.10%), Microbacterium (0.5%), Novosphingobium (0.02%), Gordonia (0.5–0.1%), and Sphingopyxis (0.07%).