Skip to main content

TECNOLOGIAS AVANZADAS PARA LA EVALUACION Y REDUCCION DE RIESGOS EN LAS INFRAESTRUCTURAS DE TRANSPORTE: EMISION DE GASES Y NANOPARTICULAS

BIA2016-79582-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2016
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Triboemission of FINE and ultrafine aerosol particles: A new approach for measurement and accurate quantification

  • Nevshupa, Roman
  • Castellote, Marta
  • Cornelio, Jesus Antonio Carlos
  • Toro, Alejandro
This article belongs to the Special Issue Selected Papers from the 7th European Conference on Tribology (ECOTRIB2019)., A dynamic model based on mass balance of fine aerosol particles was developed in order to tackle the problem of accurate quantification of mechanically stimulated particle emission (MSPE) from nanofunctionalized and solid lubricating materials. In contrast to the conventional approach, the model accounts for the effect of air turbulization caused by moving parts of the experimental tribological setup on the enhancement of particle deposition velocity. The increase of the velocity of the moving parts results in an increase of the deposition velocity that leads to a significant underestimation of experimentally measured particle emission rates. The developed model was experimentally verified using natural and artificial nanoparticle aerosols. Finally, the new methodology of particle emission rate quantification was employed for the analysis of fine particle emission produced when the solid lubricating materials were tested against a sliding steel surface. The developed method paves the way for defining a standard method of experimental assessment of nanoparticle triboemission enabling the experimental results obtained in various laboratories to be compared. It also bridges the gap between the phenomenological models and experimental measurements., This research was funded by European Union’s Horizon 2020 research and innovation programme under the Grant Agreement No LIFE13 ENV/ES/001221 and by the Spanish Ministry of Science, Innovation and Universities through the grants BIA2016-79582-R and EIN2019-102889 and Spanish National Research Council through the grant COOPB20363., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Transient aspects of plasma luminescence induced by triboelectrification of polymers

  • Puhan, Debashis
  • Nevshupa, Roman
  • Wong, Janet S. S.
  • Reddyhoff, Tom
Transient electric gas discharges that occur around sliding interfaces during contact electrification of polymers were studied at millisecond timescales and with micrometre resolution. Deduced vibrational temperatures indicate cold plasma resulting from positive corona discharge. At millisecond timescales, previously unseen rapid discharge events are observed, and modelling suggests that these result from streamer development, triggered by electron emission from the polymer surface. Those which occur over a period of several seconds are shown to be caused by competition between charge generation and the formation of polymer films. The findings explain the interplay between charging and plasma generation and their dependence on wear processes., This research was supported by the UK Engineering and Physical Sciences Research Council (EP/J002100/1), with additional equipment funding provided by the Taiho Kogyo Tribology Research Foundation (11A01). RN acknowledges the support provided by the Spanish Ministry of Economy, Industry and Competitivity through the grant BIA2016-79582-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Unconventional approaches to hydrogen sorption reactions: Non‐thermal and non‐straightforward thermally driven methods

  • Ares, José R.
  • Nevshupa, Roman
  • Muñoz-Cortés, Esmeralda
  • Sánchez, Carlos
  • Leardini, Fabrice
  • Ferrer, Isabel J.
  • Minh Huy Tran, Vo
  • Aguey‐Zinsou, Francois
  • Fernández Lozano, José Francisco
In the last decades, a broad family of hydrides have attracted attention as prospective hydrogen storage materials of very high gravimetric and volumetric capacity, fast H2‐sorption kinetics, environmental friendliness and economical affordability. However, constraints due to their high activation energies of the different H2‐sorption steps and the Gibbs energy of their reaction with H2 has led to the need of high thermal energy to drive H2 uptake and release. High heat leads to significant degradation effects (recrystallization, phase segregation, nanoparticles agglomeration…) of the hydrides. In this context, this short review aims to summarize alternative non‐thermal methods and non‐straightforward thermally driven methods to overcome the previous constraints. The phenomenology lying behind these methods, i. e. tribological activation, sonication, and electromagnetic radiation, and the effect of these processes on hydrogen sorption properties of hydrides are described. These non‐usual approaches could boost the capability of the next generation of solid‐hydride materials for hydrogen conversion in energy sector, in mobile devices and as hydrogen reservoirs., MIRE group thanks Spanish MINECO for funding support through grant MAT2015‐65203‐R. Technical assistance by Mr. Fernando Moreno is also gratefully acknowledged. MERLIN group acknowledges the financial support by UNSW Internal Research Grant program as well as the Office of Naval Research (Award No: ONRG‐NICOP‐N62909‐16‐1‐2155). We appreciate the use of instruments in the Mark Wainwright Analytical Centre at UNSW. Finally, Dr. R. Revshupa thanks to the grant BIA2016‐79582‐R supported by Spanish MINECO., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Multiparametric study of Leidenfrost point and wettability of lubricants on high-pressure die-casting dies

  • Zabala, Borja
  • Igartua, Amaya
  • Scarpis, Valeria
  • Timelli, Giulio
  • Girot, Frank
  • Nevshupa, Roman
This work is aimed at improving the lubricant film formation on the die surfaces in high-pressure die-casting (HPDC) pursuing enhancing cooling, temperature homogenization and casting release. An original test procedure was employed to study the Leidenfrost point (LFP) and the contact angle (CA) of various lubricants on die steel grades in the temperature range from 20 to 320 °C. The effects of various parameters such as steel grade, surface roughness, ageing, temperature, droplet size, water hardness and lubricant concentration on LFP and CA were isolated and analysed. It was found that the LFP remarkably increased for aged die surface with fine grains and relatively high roughness. The CA was affected mainly by the type of the lubricant. These findings lay the ground for optimal selection of the HPDC lubrication depending on the specific operating conditions., This work was funded through the European Project MUSIC (FP7-FoF-ICT-2011.7.1, under Contract nº 314145) and supported in part by the Spanish Ministry of Economy and Competitiveness (project BIA2016-79582-R) with contribution of the European Regional Development Fund., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

The effect of environmental variables on early corrosion of high–strength low–alloy mooring steel immersed in seawater

  • Nevshupa, Roman
  • Martínez Sierra, Isabel
  • Ramos, Sara
  • Arredondo, A.
Traditionally, the designing of mooring lines has been aimed at fulfilling the mechanical strength criteria using standard theoretical models and simulation in wave tunnels. This approach has led to various critical failures since degradation of a mooring line under specific environmental and loading conditions, which depend on the locations of the off-shore platforms, were not properly considered. The purpose of this paper is to investigate into the effect of three environmental variables – temperature, salinity and dissolved oxygen – on the corrosion behaviour of two steel grades used for mooring chains and to develop an empirical model intended to link these variables with the corrosion rate. A full-factorial experiment was designed on the basis of the statistical analysis of the objective data on the ocean water conditions corresponding to nine regions of Atlantic, Indic and Arctic oceans. A practical uncoupled method to determine the corrosion rate of these steel grades as function of the water conditions was developed., The authors acknowledge the financial support from the Spanish Ministry of Economy and Competitiveness through the projects IPT-2012-1167-120000 with contribution from the European Regional Development Fund of the European Union (FEDER) and BIA2016-79582. Authors would also like to thank the project partners: Vicinay Cadenas, Gerdau Aceros Especiales, IK4-Azterlan and IK4-Tekniker for their collaboration., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Photoelectrochemical global approach to the behaviour of nanostructured anatase under different irradiation conditions

  • Lee, Siaw Foon
  • Jiménez-Relinque, Eva
  • Martínez Sierra, Isabel
  • Castellote, Marta
An anatase film electrode on FTO glass has been produced by a mix of commercial nanostructured anatase with water in a dispersion using a glass rod followed by calcination at 400 ◦C for one hour with the ramp of 20 ◦C per minute. The structural morphology of the resulting surface has been analysed by scanning electron microscopy (SEM) and its photoelectrochemical behaviour in the dark, at laboratory environment and under UVA light has been examined using different electrochemical techniques as open circuit photovoltage decay (OCP), linear sweep voltammetry (LSV), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and Mott-Schottky plot measurements allowing a global electrochemical approach. Analysis of the results has allowed a better understanding about its photoelectrochemical properties and charge transfer abilities in photocatalytic applications., The authors want to acknowledge the Spanish Agency for Research belonging to the Ministry of Science and Innovation, Spain, for funding this research through the grant ID BIA2016-79582-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Evaluation of changes in surface temperature of TiO2 functionalized pavements at outdoor conditions

  • Fernández-Mira, Maria
  • Jiménez-Relinque, Eva
  • Martínez Sierra, Isabel
  • Castellote, Marta
Surface temperature of ten different materials (combination of different commercial TiO-based photocatalysis on different types of substrate) located outdoors have been recorded for a 12-hours period using an infrared thermography camera after 2 years of exposure to environmental conditions. Twin conventional pavement‘s substrates (asphalt, and three kinds of tiles) were also evaluated as a reference. A detailed optical, chromatic, and textural characterisation was performed and statistical analysis was carried out to further understand the significance of the parameters that control the surface temperature changes. It generally seems that the mean daily surface temperature and temperature range of the TiO modified materials are lower than their corresponding conventional material. The observed differences on the thermal behavior does not seem to be directly related to the TiO photocatalytic effectiveness. The emissivity values do not show significant variations by the application of the nano-TiO additives. A multivariable correlation has allowed to deduce that main contribution to the lower temperature in the photocatalytic pavements is due to the smoother surface induced by the addition of the photocatalyst., The authors would like to thank the financial support provided by LIFE program’s (LIFE PHOTOSCALING-LIFE13 ENV/ES/001221), national project (BIA2016-79582-R, TEVALRISK) and from Fundación General del CSIC (Programa ComFuturo) for the research contract of Eva Jimenez-Relinque. Also acknowledge the introduction to research Scholarship JAE-Intro (October 2019 - June 2020) in the ISCMA (Sustainable Interaction between Construction Materials and the environment) research group of IETcc (Construction Science Institute Eduardo Torroja) belonging to the CSIC (Spanish National Research Council).