Skip to main content

MATERIALES FERROICOS PARA BAJO CONSUMO DE ENERGIA

PID2021-124734OB-C21

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprogram Subprograma Estatal de Generación de Conocimiento
Call Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Call year 2021
State Plan 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 16
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Electrocaloric effect near room temperature in lead-free Aurivillius phase Sr2Bi4Ti5O18 upon La and Nb codoping [Dataset]

  • Lafuerza, Sara
  • Gracia, David
  • Blasco, Javier
  • Evangelisti, Marco
[Description of methods used for collection/generation of data] Crystal structures were characterized by powder X-ray diffraction (XRD) at room temperature in a Rigaku D-Max system using Cu Kα1,2 wavelengths. Rietveld analysis of the X-ray patterns was performed using the Fullprof package program. Electrical and electrocaloric properties measurements were conducted on sintered disc-shaped samples, with typical dimensions of 8 mm diameter and thickness between 0.5 and 1 mm. Electrodes were made with silver paste in sandwich geometry. The dielectric constant was derived from measurements with an impedance analyzer (Wayne Kerr Electronics 6500B), applying sinusoidal excitations of 1 V amplitude at several frequencies between 100 Hz and 4 MHz. The polarization versus electric field P(E) curves were recorded using a commercial polarization analyzer (aixACCT Easy Check 300) jointly with a high voltage amplifier (Trek 610E), applying sinusoidal excitations with typical frequency of 10 Hz and E field amplitudes up to 70 kV/cm. Direct measurements of the electrocaloric effect (ECE) were performed using a dedicated in-house-developed quasi-adiabatic calorimeter. The adiabatic temperature change was measured as a function of temperature every 1 K and at different applied E field variations. Samples were measured in the “contactless” mode to minimize heat losses, held only by the high voltage coaxial cable and K-type thermocouple for the direct measurement of the temperature variation. Voltages up to either 2 kV or 5 kV were applied using two different homemade high-voltage converters. Heat capacity measurements were also performed, using a commercial adiabatic calorimeter (from Termis Ltd.)., [Methods for processing the data] For the indirect estimation of the electrocaloric effect, well-known thermodynamic formulations based on Maxwell relations have been applied to the polarization data recorded at several temperatures, to derive entropy variations as a function of temperature., La and Nb codoping of the five-layer Aurivillius phase Sr2Bi4Ti5O18 induces compositional disorder and diffuse relaxor transitions at much lower temperatures than the undoped ferroelectric compound (560 K), while preserving the orthorhombic structure. For moderate La and Nb concentrations, the ferroelectric properties are enhanced in the vicinity of room temperature, and so is their electrocaloric effect measured directly with a homemade quasi-adiabatic calorimeter. The adiabatic temperature change reaches, e.g., ΔT ⁓ 0.3 K at 355 K with a temperature span ⁓ 15 K, under ΔE = 37 kV/cm. The large field dispersion of the effect is ascribed to field-induced transitions from short-range-ordered relaxor to long-range-ordered ferroelectric states. Indirect estimations of the electrocaloric effect from electric polarization data are not able to quantitatively predict the direct results and emphasize the need of applying direct measurement methods, especially for relaxor ferroelectrics., Marie Skłodowska-Curie grant agreement No. 101029019; Ministerio de Ciencia, Innovación y Universidades (PID2021-124734OB-C21); Diputación General de Aragón (E11-23R, E12-23R)., SBLTN_Fig2_XRay.dat SBLTN_Fig3a_DielectricConstant.dat SBLTN_Fig3b_DielectricConstant.dat SBLTN_Fig4a_DielectricConstant.dat SBLTN_Fig4b_DielectricConstant.dat SBLTN_Fig5_Polarization.dat SBLTN_Fig6a_Polarization.dat SBLTN_Fig6b_Polarization.dat SBLTN_Fig6c_Polarization.dat SBLTN_Fig6d_Polarization.dat SBLTN_Fig7a_DeltaT.dat SBLTN_Fig7b_DeltaT.dat SBLTN_Fig7c_DeltaT.dat SBLTN_Fig7d_DeltaT.dat SBLTN_FigS1_XRay.dat SBLTN_FigS2_XRay.dat SBLTN_FigS3_XRay.dat SBLTN_FigS4_XRay.dat SBLTN_FigS5a_Polarization.dat SBLTN_FigS5b_Polarization.dat SBLTN_FigS6a_Polarization.dat SBLTN_FigS6b_Polarization.dat SBLTN_FigS6c_Polarization.dat SBLTN_FigS6d_Polarization.dat SBLTN_FigS7a_Polarization.dat SBLTN_FigS7b_Polarization.dat SBLTN_FigS7c_Polarization.dat SBLTN_FigS7d_Polarization.dat SBLTN_FigS8_DirectECE.dat SBLTN_FigS9_DirectECE.dat SBLTN_FigS10_HeatCapacity.dat, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Dodecanuclear [NiII8Ln4] clusters: rings of corner-sharing {NiII2Ln2} cubanes (Ln = Dy, Gd, Y}

  • Tziotzi, Thomais G.
  • Agapaki, Eleftheria
  • Charkiolakis, Emmanouil K.
  • Gracia, David
  • Ubach I Cervera, Marc
  • Dalgarno, Scott J.
  • Evangelisti, Marco
  • Brechin, Euan K.
  • Milios, Constantinos J.
[Description of methods used for collection/generation of data] Magnetisation data were collected on MPMS-XL and MPMS3 SQUID magnetometers equipped with 5 and 7 T magnets, respectively. Diamagnetic corrections were applied using Pascal's constants. Heat capacity measurements were carried out on a PPMS equipped with a 9 T magnet and a 3He cryostat, using a thin pressed pellet (ca. 1 mg) of a polycrystalline sample of 2, thermalized by ca. 0.2 mg of Apiezon N grease, whose contribution was subtracted using a phenomenological expression., [Methods for processing the data] An indirect estimation of DS and DT was performed in accordance with standard thermodynamic formulations., The solvothermal reaction of NiCl2.6H2O with 1,3,5-tri(2-hydroxyethyl)-1,3,5-triazacyclohexane, LH3, and Ln(OAc)3.4H2O in the presence of salicylaldehyde in MeOH leads to the formation of the dodecanuclear isostructural species [NiII8Ln4(L’)8(OAc)4(OH)8(H2O)4].xH2O (Ln= Dy, x=6 (1); Gd, x= 24 (2); Y, x= 10 (3); L’ = the dianion of the Schiff-base resulting from the reaction of salicylaldehyde and ethanolamine). The metallic core of the clusters describes a ring a of corner-sharing {Ni2Ln2} cubanes assembled on a central, planar rectangular {Ln4} unit. Magnetization studies conducted on complexes 1 - 3 demonstrate the presence of dominant ferromagnetic exchange at low temperatures, which is largely attributed to the Ni⋯Ni interactions. The significant magnetocaloric effect observed in the Gd analogue has been assessed through heat-capacity and magnetization measurements., This work has received support from EU (MSCA-DN MolCal, 101119865), MICIU/AEI/10.13039/501100011033/ and ERDF/EU (PID2021-124734OB-C21, CEX2023-001286-S), Gobierno de Aragón (E11-23R, E12-23R). CJM and TGT would like to thank the National Recovery and Resilience Plan Greece 2.0 (Award Number TAEDR-0535821), funded by the European Union − NextGenerationEU., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Enhanced magnetoelastic stress in disordered iron-gallium alloy thin films revealed by direct measurement [Dataset]

  • Begué Gracia, Adrián
  • Proietti, M. G.
  • Arnaudas, José I.
  • Ciria, Miguel
[Description of methods used for collection/generation of data] RHEED images (files starting with Fig1b) were collected using a digital camera UK1117m equipped with a Sony ICX415AL sensor. The pixel type is gray with a pixel width of 8 bits and a variable exposure time and gain was used. Film thickness was obtained with a Discover D8 diffractometer with Cu Ka1 radiation (files starting with Fig1c). Bragg-Bentano scans were conducted with a Rigaku X-ray diffraction at Cu Ka radiation. (files starting with Fig1d). Composition was determined using energy-dispersive X-ray spectroscopy (EDX) using a INSPECT-F50 SEM (https://lma.unizar.es/sem-inspect/) and Wavelength Dispersive Spectroscopy (WDS) in an electron probe micro-analyzer (EPMA) instrument (JXA-iHP200F at the Universidad of Zaragoza). Synchrotron X-ray diffraction measurements were conducted at the BM25 beamline of the ESRF synchrotron at room temperature. A monochromatic beam with a wavelength of 0.7 Å was used. (files starting with Fig2). The reference grid is obtained using the MgO reflections of the monocrystalline substrate used to grow the films. Several non-collinear reflections are requested to calculate the matrix elements. Synchrotron XAS measurements were conducted at the Fe and Ga K-edges at beamline I18 of the Diamond UK’s National Light Source at beamline I18 of the Diamond UK’s National Light Source. Magnetization measurements were obtained using nanoMOKE3 magnetometer using laser beam with p-polarization and red (650 nm wavelength) light. High-field lineal correction is applied. Cantilever beam measurements. The magnetoelastic stress was obtained using a cantilever beam method. The sample is clamped by one end, and a constant magnetic field of 100 mT is rotated. The magnetic field is generated by a homemade dipole mounted on a motorized rotatory stage(Standa 8MR190-90-4247). Several turns are performed to correct drifts and other errors. The capacitor is built with the sample that covers a second smaller electrode. The capacitance is measured using an Andeen Hagerling 2500A capacitance bridge at 1kHz. The difference in capacitance with the magnetic field along the beam and forming 90 degrees is used to obtain the magnetoelastic stress. That value is multiplied by the factor indicated in the Appendix. Files starting with Fig6 include the capacitance recollected, Cap, the capacitance with a correction (using a 4-degree polynomial) to eliminate drift, deltaC, the magnetoelastic stress, ME. and the angular position, angle, starting with H along the beam length., [Methods for processing the data] XAS data. The experimental spectra were fitted by theoretical EXAFS signals calculated by ab initio theoretical phase and amplitudes generated for a cluster of 78 atoms with a radius of 6.1 Å-1, by the TKAtoms code. The central absorber was a Ga or Fe atom with only one kind of Ga (Fe) scatterer. The alloying FeGa effect was obtained by combining the pure Ga-Fe(Ga) and Fe-Fe(Ga)systems at the Ga and Fe K-edge, respectively. The 8.01 Feff code generated the theoretical phase-shifts and amplitudes taking into account beam polarization. The ATHENA and ARTEMIS packages were used for extraction and best-fit procedure of the EXAFS spectra. The best-fit analysis for the two polarizations was performed simultaneously in q-space, in the range 2 - 11 Å-1, by Fourier Filtering of the first peak contribution of the FT spectra that is due to the first and second coordination shells. The contributions of next neighbor (NN) and next-nearest-neighbor (NNN) atoms are merged into a single FT peak due to the proximity of the interatomic distances values (2.48 Å and 2.87 Å respectively in pure bcc Fe). The best-fit parameters were the origin of the photoelectron energy E0, the Ga population in NN and NNN environments, the interatomic distances of first and second coordination shells, and the Debye-Waller factors. The FDMNES code is used to perform \textit{ab initio} simulations of the XANES spectra., The large magnetostriction in FeGa alloys is relevant for manifold applications, but for thin films, it can play a prominent role in controlling the strength of the magnetic anisotropy. Bulk samples show values depending on the extensive preparation procedure compendium, which is limited in its temperature range for high-quality thin-film synthesis. Here, we present a study of the magnetoelastic coupling coefficients B1 and B2 in epitaxial FeGa thin films below 50 nm deposited on the MgO(001) surface at 150 ºC by the cantilever method. Series of films with 22, 28, and 33 at. % Ga do not show thickness-dependent variations for B1 and B2, but -B1 for the 22 at. % Ga composition is 10 MPa, roughly 2 times the bulk value and smaller than the bulk-like value of -B1=12.1 MPa obtained for a film with 17 at. % Ga. This enhancement is correlated with the A2 crystal structure for the film rather than the coexistence with D03 or other ordered nanometric precipitates proposed for bulk samples. Synchrotron diffraction excludes the formation of long-range L60, or D03 precipitates in samples with (001)A2 peaks at concentrations around 25 at. % Ga, which implies partial chemical disorder. The analysis of extended x-ray absorption fine structure measurements points to a D03 local order with a residual number of Ga-Ga pairs. Considering that the substrate quenches the movable strain in the A2 phase described in dual-phase structures, our results point to the important role of the electronic structure of the iron atoms modified by the presence of Ga in the alloy. This effect enlarges B1 in films with the A2 phase, stabilized using epitaxial growth., This work was funded by MICIU/AEI/10.13039/501100011033, ERDF/UE, and NextGenerationEU/PRTR (PID2021-124734OB-C21, CEX2023-001286-S, TED2021-131064B-I00), Gobierno de Aragón (E12-23R) and Ministry of Universities and the European Union-Next Generation for the Margarita Salas fellowship., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., File List: Fig1b_33_13[100].png Fig1b_33_13[110].png Fig1b_17_48[110].png Fig1b_17-48[100].png Fig1b_MgO_[110].png Fig1b_MgO_[100].png Fig1c28_11.cvs Fig1c28_20.cvs Fig1c28_41.cvs Fig1d33_17.cvs Fig1d28_41.cvs Fig1d21_19.cvs Fig2b_l1.cvs Fig2b_l05.cvs Fig2b_l0.cvs Fig2c_l1.cvs Fig2c_l05.cvs Fig2c_l0.cvs Fig3a_21_10par.cvs Fig3a_21_10perp.cvs Fig3a_28_11par.cvs Fig3a_28_11perp.cvs Fig3a_33_13par.cvs Fig3a_33_13perp.cvs Fig3b_21_10par.cvs Fig3b_21_10perp.cvs Fig3b_28_11par.cvs Fig3b_28_11perp.cvs Fig3b_33_13par.cvs Fig3b_33_13perp.cvs Fig3c_33_13parData.cvs Fig3c_33_13parFit.cvs Fig3c_33_13perpData.cvs Fig3c_33_13perpFit.cvs Fig4a_22_10.cvs Fig4a_22_33.cvs Fig4a_28_41.cvs Fig4a_33_13.cvs Fig4a_33_25.cvs Fig4b_22_12.cvs Fig4b_B2.cvs Fig4b_D03.cvs Fig4c_22_12.cvs Fig4c_B2.cvs Fig4c_D03.cvs Fig5aFe100.cvs Fig5aFe110.cvs Fig5b21_19_100.cvs Fig5b21_19_110.cvs Fig6_B1_22_10.cvs Fig6_B1_22_19.cvs Fig6_B1_22_33.cvs Fig6_B1_28_11.cvs Fig6_B1_28_20.cvs Fig6_B1_28_31.cvs Fig6_B1_33_13.cvs Fig6_B1_33_25.cvs Fig6_B1_33_36.cvs Fig6_B2_22_10.cvs Fig6_B2_22_19.cvs Fig6_B2_22_33.cvs Fig6_B2_28_11.cvs Fig6_B2_28_20.cvs Fig6_B2_28_31.cvs Fig6_B2_33_13.cvs Fig6_B2_33_25.cvs Fig6_B2_33_36.cvs Fig6d.cvs, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

A linear {Fe2Ni} cluster and a structurally closely related quasi one-dimensional {Fe2Ni} chain

  • Charkiolakis, Emmanouil K.
  • Gracia, David
  • Ubach I Cervera, Marc
  • Evangelisti, Marco
  • Milios, Constantinos J.
The solvothermal reaction between FeCl3·6H2O, NiCl2·6H2O, 2-hydroxynaphthaldehyde, and glycine in MeOH results in the formation of the trinuclear heterometallic cluster [FeΙΙΙ2NiΙΙ(L1)4(MeOH)4] (1) in good yield, while the same reaction upon replacing glycine with dimethyl-glycine, results in the formation of the closely related quasi one-dimensional coordination polymer {[FeΙΙΙ2NiΙΙ(L2)4(MeOH)2]n} (2) (L1, L2: the dianionic form of the Schiff-base ligand derived from the condensation of 2-hydroxynaphthaldehyde and glycine (L1 for 1), or dimethyl-glycine (L2 for 2)). The structure of 1 describes a linear trimetallic {FeIII2Ni} unit, whereas complex 2 consists of repeating linear {FeIII2Ni} units with each one connected to two neighbouring units via four coordination bonds, forming a quasi one-dimensional chain. The structural similarity between complex 1 and the repeating unit of complex 2 is remarkable. However, their magnetic properties differ significantly, with complex 1 displaying dominant ferromagnetic interactions, and complex 2 showing antiferromagnetic interactions., This work has received support from EU (MSCA-DN MolCal,101119865), MICIU/AEI/10.13039/501100011033/ and ERDF/EU (PID2021-124734OB-C21, CEX2023-001286-S), Gobierno de Aragón (E11-23R, E12-23R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Enhanced magnetoelastic stress in disordered iron-gallium alloy thin films revealed by direct measurement

  • Begué Gracia, Adrián
  • Proietti, M. G.
  • Arnaudas, José I.
  • Ciria, Miguel
The large magnetostriction in FeGa alloys is relevant for manifold applications, but for thin films, it can play a prominent role in controlling the strength of the magnetic anisotropy. Bulk samples show values depending on the extensive preparation procedure compendium, which is limited in its temperature range for high-quality thin-film synthesis. Here, we present a study of the magnetoelastic coupling coefficients B1 and B2 in epitaxial FeGa thin films below 50 nm deposited on the MgO(001) surface at 150 ºC by the cantilever method. Series of films with 22, 28, and 33 at. % Ga do not show thickness-dependent variations for B1 and B2, but -B1 for the 22 at. % Ga composition is 10 MPa, roughly 2 times the bulk value and smaller than the bulk-like value of -B1=12.1 MPa obtained for a film with 17 at. % Ga. This enhancement is correlated with the A2 crystal structure for the film rather than the coexistence with D03 or other ordered nanometric precipitates proposed for bulk samples. Synchrotron diffraction excludes the formation of long-range L60, or D03 precipitates in samples with (001)A2 peaks at concentrations around 25 at. % Ga, which implies partial chemical disorder. The analysis of extended x-ray absorption fine structure measurements points to a D03 local order with a residual number of Ga-Ga pairs. Considering that the substrate quenches the movable strain in the A2 phase described in dual-phase structures, our results point to the important role of the electronic structure of the iron atoms modified by the presence of Ga in the alloy. This effect enlarges B1 in films with the A2 phase, stabilized using epitaxial growth., We thanks grant TED2021-131064B-I00 funded by MCIN/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR, grant PID2021-124734OB-C21 funded by MCIN /AEI /10.13039/501100011033 and by “ERDF A way of making Europe” and grant CEX2023-001286-S funded by MICIU/AEI /10.13039/501100011033 and Gobierno de Aragón, Spain (grant E12-23R). A. B. would like to acknowledge the funding received from the Ministry of Universities and the European Union-Next Generation for the Margarita Salas fellowship . We are grateful to the staff of beamline I18 at Diamond UK’s National Synchrotron Light source and BM25 Spain Beamline at ESRF for their strong support in performing the experiments. Authors would like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza. Authors acknowledge the use of instrumentation as well as the technical advice provided by the National Facility ELECMI ICTS, node Laboratorio de Microscopias Avanzadas (LMA) at Universidad de Zaragoza., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Large sub-Kelvin Magnetocaloric Effect and Phase Behavior of Gadolinium Nitrate Hexahydrate [Dataset]

  • Gracia, David
  • Ubach I Cervera, Marc
  • Charkiolakis, Emmanouil K.
  • García, Inés
  • Milios, Constantinos J.
  • Evangelisti, Marco
Continuous-wave electron paramagnetic resonance (EPR) measurements on a 1% diluted polycrystalline sample of [Gd@Y(NO3)3]6H2O were recorded using a Bruker Elexys 580 spectrometer operating in X-band (9.715 GHz). The spectrometer was equipped with an Oxford CF900 continuous-flow cryostat, which employs liquid-helium to cool down the sample environment. The microwave power was adjusted to avoid saturation effects. The magnetic field was measured with a Bruker ER035 gaussmeter. Direct-current (DC) magnetic measurements were performed on a polycrystalline powder sample (ca. 5 mg), loaded into a plastic capsule and immobilized with eicosane wax to prevent grain movement. Isothermal magnetization curves were collected in magnetic fields between 0-7 T over the temperature range 2-10 K. DC magnetic susceptibility data were recorded over the same temperature range under a constant applied magnetic field of B=0.1 T. All data obtained were corrected for diamagnetic contributions coming from both the sample holder and eicosane wax. In addition, the complex alternating-current (AC) magnetic susceptibility was measured under zero applied magnetic field over the temperature range 0.05-4 K, using a frequency of 525 Hz and an AC field amplitude of 2·10^{-4} T. A thin pressed polycrystalline pellet (ca. 6 mg) was prepared for these experiments, and susceptibility data were initially recorded in arbitrary units. Absolute values of the real component were obtained by comparison with DC susceptibility data collected with the MPMS-3 in the overlapping temperature range (2-4 K), where dissipative processes are negligible. The imaginary component is reported in arbitrary units. Heat capacity measurements were carried out using the relaxation method in a Quantum Design PPMS equipped with a 3He cryostat, covering temperatures down to 0.4 K under constant magnetic fields from 0 to 7 T. Additional measurements extended to 0.05 K under fields up to 1 T using a Quantum Design PPMS DynaCool with DR module. Samples consisted of thin pressed polycrystalline pellets (ca. 1 mg for 3He and ca. 0.2 mg for DR). In both setups, Apiezon N grease (0.2 mg) was applied to ensure good thermal contact between the sample and the calorimeter platform. Its contribution to the total heat capacity was subtracted using a phenomenological correction. Direct quasi-adiabatic MCE measurements were performed for complete demagnetization processes. For these experiments, a pressed polycrystalline pellet of ca. 5 mg was mounted on a calorimeter platform coated with ca. 0.2 mg of Apiezon N grease to improve thermal coupling. In addition, the MCE was also evaluated indirectly by applying standard thermodynamic relations to the measured magnetization and heat capacity data., We report a comprehensive magnetothermal study of the classical gadolinium salt [Gd(NO3)3]·6H2O at temperatures approaching absolute zero. Despite its long-standing availability as a commercial compound, its magnetocaloric properties have remained unexplored. Using electron paramagnetic resonance, magnetic susceptibility, heat capacity, and direct measurements of the magnetocaloric effect, we reveal that weak dipolar interactions combined with axial crystal-field anisotropy drive antiferromagnetic ordering at T_N = 0.21 K. Remarkably, [Gd(NO3)3]·6H2O exhibits an isothermal magnetic entropy change of -\Delta S_m = 26.1 J / K kg at T = 0.6 K for a modest field variation of Delta-B = 1 T, and an adiabatic temperature change of Delta-T_ad = 5.0 K at T = 1.6 K for the same Delta-B, outperforming many state-of-the-art Gd-based refrigerants. These results provide a reference for understanding magnetocaloric behavior in hydrated salts and highlight the interplay between crystal-field anisotropy and dipolar coupling at ultra-low temperatures., This work was funded by EU (MSCA-DN MolCal, 101119865), MICIU/AEI/10.13039/501100011033/ and ERDF/EU (PID2021-124734OB-C21, PID2024-159457OB-C21, CEX2023-001286-S)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

High-quality epitaxial five-layer Aurivillius films with in-plane ferroelectricity for electrocaloric cooling [Dataset]

  • Lafuerza, Sara
  • Blasco, Javier
  • Evangelisti, Marco
  • Subías, Gloria
  • Gracia, David
  • Pardo, José A.
  • Barriuso, Eduardo
  • Torrelles, Xavier
  • Padilla-Pantoja, Jessica
  • Caicedo, José Manuel
  • Santiso, José
[Description of methods used for collection/generation of data]: The structural characterization of the films was performed by X-ray diffraction (XRD) 2θ/ω wide scans, X-ray reflectivity (XRR) and reciprocal space maps (RSMs) of selected asymmetric reflections, by using a four-circle X-ray diffractometer (Malvern-Panalytical X'pert Pro MRD) and standard Cu Kα1,2 X-ray source with a parabolic mirror (for reciprocal space maps, a 2xGe(220) monochromator was added to the incident optics). A 2D array PIXcel detector was used. The topography of selected films was studied using atomic force microscopy (AFM) in contact mode (Keysight 5100) over different areas. The structure of the films was also analyzed by high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) on a Fisher Spectra microscope operated at 200 kV. Cross-section lamellas were prepared by focused ion beam (FIB) on a SBTO5 film deposited under optimized conditions, with the cut oriented to show STO [100] zone axis., [Ferroelectric and Electrocaloric Properties]: These properties were investigated by measuring the in-plane polarization using the IDEs with a 500 V-built-in ferroelectric tester (Precision Premier II model, Radiant Technologies). Hysteresis measurements were carried out based on a bipolar triangular wave excitation, and also remanent hysteresis measurements based on half triangular waves following the principle of the positive-up negative-down (PUND) method. The frequency of the triangular wave excitation was set to 2 kHz for both measurement protocols. Temperature (T)-dependent polarization versus E field, P(E, T) curves, were measured on heating in a dedicated homemade cell allowing a maximum temperature of 140 °C. Samples were immersed in a silicon oil bath during the polarization measurements to avoid electric discharges., High-quality purely c-axis oriented epitaxial thin films of the Aurivillius phase Sr2Bi4Ti5O18 with n = 5 (Sr,Bi)TiO3 perovskite-like layers, are grown on SrTiO3 substrates by pulsed laser deposition. The highest crystalline quality is obtained with a 20 wt.% Bi-excess target and average stacking order values in the proximity of the ideal value n = 5 are attained for an optimum deposition temperature of 650 °C. Scanning transmission electron microscopy reveals regions with n ranging from 4 to 6 around an average thickness of n = 5, in agreement with the X-ray diffraction analysis. Interdigital electrodes are used to probe the in-plane polarization and survey the electrocaloric properties. A maximum adiabatic temperature change of ΔT ∼ 0.95 °C for an electric field of 150 kV cm−1 is observed at ≈135 °C. Larger values are expected at higher temperatures around the ferroelectric Curie temperature, TC. Since TC of Sr2Bi4Ti5O18 can be tuned by codoping, the findings pave the way toward a large electrocaloric effect at ambient temperature., S.L. acknowledges funding from the European Union's Horizon 2020 research and innovation program under the Marie Skłodowska-Curie grant agreement No. 101029019. This work was also supported by Ministerio de Ciencia, Innovación y Universidades (PID2021-124734OB-C21), “Severo Ochoa” Programme for Centres of Excellence in R&D (CEX2023-001286-S, CEX2023-001263-S and CEX2021-001214-S) and Diputación General de Aragón (E11-23R, E12-23R). D. G. acknowledges financial support from the Gobierno de Aragón through a doctoral fellowship. Authors would like to acknowledge C. Cosculluela from Unidad Técnica en Ingeniería de Microdispositivos (INMA) and R. Valero for the IDEs fabrication at the National Facility ELECMI ICTS, node “Laboratorio de Microscopías Avanzadas”, through Servicio General de Apoyo a la Investigación from Universidad de Zaragoza. The authors also acknowledge the use of instrumentation as well as the technical advice provided by the Joint Electron Microscopy Center at ALBA (JEMCA) and funding from Grant IU16-014206 (METCAM-FIB) to ICN2 funded by the European Union through the European Regional Development Fund (ERDF), with the support of the Ministry of Research and Universities, Generalitat de Catalunya. J. S. acknowledges B. Mundet, F. Belarre and M. Rosado for the STEM images and FIB fabrication of the lamellas, as well as the financial support of the European Commission through the Horizon H2020 funding by H2020-MSCA-RISE-ID:101007825 –ULTIMATE-I. X. T. acknowledges financial support by Ministerio de Ciencia, Innovación y Universidades (PID2021-123276OB-I00)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001263-S)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001214-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Exploring a route to induce ferromagnetism on Sr3Sn2O7 by co-doping with non-Jahn-Teller-distorted Mn3+ and La3+ cations [Dataset]

  • Blasco, Javier
  • Cuartero, Vera
  • Lafuerza, Sara
  • Gracia, David
  • Puente-Orench, Inés
  • Rodríguez-Velamazán, J. A.
  • Herrero Martín, Javier
  • Torchio, Raffaella
  • Mathon, Olivier
  • Subías, Gloria
The samples were characterized by X-ray powder diffraction (XRD) using a Rigaku D-system using Cu Kα1,2 wavelengths and an angular range of 6º ≤ 2θ ≤ 135º at room temperature. Neutron powder diffraction (NPD) measurements were performed at the high-flux reactor of the ILL (Grenoble, France) using the high-intensity powder diffractometer D1B with a detector angular range coverage 5º ≤ 2θ ≤ 128º. A wavelength of λ ≈ 2.52Å was used in a temperature range between 2 K and 150 K. Magnetic measurements were carried out between 5 and 400 K by using a commercial superconducting quantum interference device (SQUID) magnetometer from Quantum Design. The measurements were performed warming the sample after zero-field cooling at an external magnetic field of 1 kOe. Isothermal magnetization measurements at selected temperatures between 5 and 250 K were performed for externals fields between -50 and 50 kOe. Mn-L2,3 (630−670 eV) edge X-ray absorption spectroscopy (XAS) measurements were performed at the at the HECTOR cryomagnet end station in the BL29 BOREAS beamline of the ALBA synchrotron radiation facility (Barcelona, Spain). The photon flux was about 10^12 ph/s with an energy resolution of ∼50 meV. Sintered pellets were used for the XAS measurements, which were also cleaved in situ under ultrahigh vacuum conditions (∼10^−9 mbar) to obtain clean sample surfaces. Measurements were recorded in total electron yield mode (i.e. drain current detection) at 300 K. Mn K-edge XAS measurements at room temperature were performed at the BM23 beamline at the ESRF (Grenoble, France). The spectra were collected in fluorescence mode geometry by using a multi-element silicon drift detector. A Mn foil was measured for energy calibration., We here explore a route to induce a ferromagnetic ground state on the Ruddlesden-Popper phases Sr3-xLaxSn2-xMnxO7 replacing Sn by Mn up to x=1.25. Ferroelectric-paraelectric transitions above room temperature are found in the low Mn-content samples (x≤0.1), with polar space group A21am. For higher Mn concentrations (x ≥ 0.25) the samples are paraelectric and adopt the centrosymmetric space group Amam due to the suppression of specific rotational modes. X-ray absorption spectroscopy confirmed the presence of a Mn3+ ion in all samples though it is not Jahn-Teller distorted. An average regular MnO6 octahedral local structure is reported instead, with Debye-Waller factors for the Mn-O bond length increasing as Mn content does, due to the disorder induced in the Sn/Mn sublattice and the rising of rumpling distortions (expansion of the perovskite bilayer coupled with shrinkage of the rock salt layer). All the Sr3-xLaxSn2-xMnxO7 samples exhibit ferromagnetic correlations. While Mn³⁺ cations in low Mn-content samples (x ≤ 0.25) agree with spin-only contributions, higher doping levels deviate from this interpretation, possibly due to the enhancement of magnetic interactions. At 5 K, all samples exhibit spontaneous magnetization which increases with Mn content, but the Mn³⁺ magnetic sublattice is not fully polarized. Neutron diffraction confirmed the absence of long-range magnetic order and AC susceptibility analysis indicates a glassy magnetic state due to structural disorder and competing interactions. Compared to simple perovskites, our results indicate that the rock salt layer plays a key role in suppressing long-range ferromagnetic order, making it particularly challenging to achieve multiferroic behavior by doping hybrid improper ferroelectrics with magnetic cations., Financial support from PID2021-124734OB-C21 and -C22 together with grant CEX2023-001286-S funded by MICIU/AEI/10.13039/501100011033 and, as appropriate, by “ERDF A way of making Europe”, and Diputación General de Aragón (projects E11-23R and E12-23R). Granted beam time at ILL, via Spanish Initiatives on Neutron Scattering (SpINS),Experiment CRG-2990; doi: 10.5291/ILL-DATA.CRG-2990. Beam time allocation at ALBA (proposal codes 2023027292 and 20250330019) and ESRF (exp blc15406) synchrotrons., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Exploring the magnetic percolation threshold in the improper ferroelectric Sr3Sn2O7 upon Cr and Fe-doping [Dataset]

  • Blasco, Javier
  • Cuartero, Vera
  • Lafuerza, Sara
  • Gracia, David
  • Rodríguez-Velamazán, J. A.
  • Puente-Orench, Inés
  • Subías, Gloria
The samples were characterized by X-ray powder diffraction (XRD) using a Rigaku D-system using Cu Kα1,2 wavelengths. Neutron powder diffraction measurements were performed at the high-flux reactor of the ILL (Grenoble, France) using the high-intensity powder diffractometer D1B with a detector angular range coverage 2º ≤ 2θ ≤ 128º. A wavelength of λ ≈ 2.52Å was used for the determination of the low-temperature magnetic structure in a temperature range between 2 K and 150 K.Magnetic measurements were carried out between 5 and 400 K by using a commercial superconducting quantum interference device (SQUID) magnetometer from Quantum Design. The measurements were performed warming the sample after zero-field cooling at an external magnetic field of 1 kOe. Isothermal magnetization measurements at selected temperatures between 5 and 250 K were performed for externals fields between -50 and 50 kOe. The relative dielectric permittivity was derived from measurements with an impedance analyzer (Wayne Kerr Electronics 6500B), applying sinusoidal excitations of 1 V amplitude at 900 kHz. Temperature dependent measurements were conducted in homemade sample insert in either a tubular furnace (above room temperature) or an Oxford Instruments cryostat (from 120 K up to 400 K), with 1 K/minute heating ramps. The polarization versus electric field (𝑃-𝐸) hysteresis loops were collected at room temperature in silicon oil, using a 500 V-built-in ferroelectric tester (Precision Premier II, Radiant Technologies) jointly with a high voltage amplifier (610E, Trek). Excitation signals with frequency of either 100 or 250 Hz and maximum electric (E) field amplitude of 125 kV/cm were applied., We examine the effect of Fe and Cr substitutions at the Sn site on the magnetic properties of the hybrid improper ferroelectric Sr3Sn2O7. Upon co-doping with La to preserve the electric charge balance in the unit cell, the Sr3-xLaxSn2-xCrxO7, Sr3-xLaxSn2-xFexO7 and Sr2LaSnFe1-yCryO7 series can be obtained as single phases up to x=1 and for all y values. The unit cell volume is isotropically reduced with doping, so that the orthorhombic structure is preserved. However, these substitutions strongly destabilize the ferroelectric order by decreasing the transition temperature, Tc, below room temperature for x≥0.25. La/Cr co-doping is unable to induce long-range magnetic and compositions from this series behave as conventional paramagnetic compounds; although for high doping concentration (x≥0.5), the significant deviations from the Curie law at low temperatures suggest the onset of antiferromagnetic correlations. In the case of La/Fe co-doping, all samples show strong antiferromagnetic correlations, but a spin glass-like behavior is observed for x≈1 compounds. Finally, no long-range magnetic ordering is observed in La/Cr-Fe co-doped samples. but at the same time an increase in spontaneous magnetization is seen at low temperature, which is associated with the presence of competitive magnetic interactions, in particular the Fe-O-Cr superexchange ferromagnetic interaction. The lack of long-range magnetic order in the investigated series of Cr/Fe-doped Sr3Sn2O7, indicates that the critical concentration of magnetic atoms necessary to overcome the magnetic percolation threshold exceeds the 50% in magnetic cations in these bilayered Ruddlesden-Popper perovskites., Financial support from MICIU/AEI/10.13039/501100011033/FEDER, UE (PID2021-124734OB-C21, CEX2023-001286-S) and Diputación General de Aragón (E11-23R, E12-23R). Granted beam time at ILL, via Spanish Initiatives on Neutron Scattering (SpINS),Experiment CRG-2990; doi:10.5291/ILL-DATA.CRG-2990., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Effects of doping with magnetic cations on the hybrid improper ferroelectricity in Sr3Sn2O7 [Dataset]

  • Blasco, Javier
  • Gracia, David
  • Lafuerza, Sara
  • Cuartero, Vera
  • Subías, Gloria
The samples were characterized by X-ray powder diffraction (XRD) using a Rigaku D/MAX 2500-system and Cu Kα1,2 wavelengths.Magnetic measurements were carried out between 5 and 320 K by using a commercial Superconducting Quantum Interference Device (SQUID, Quantum Design). Electrical properties measurements were conducted on sintered disc-shaped samples, with typical dimensions of 8 mm diameter and thicknesses from 0.2 to 0.7 mm. Electrodes were made with silver paste in sandwich geometry. Temperature dependent measurements were conducted in a homemade sample insert placed inside a tubular furnace. Both heating and cooling ramps with a typical velocity value of 1 K/minute were applied. The polarization versus electric field (𝑃-𝐸) hysteresis loops were collected at room temperature in silicon oil, using a 500 V-built-in ferroelectric tester jointly with a high voltage amplifier., We here report the structural, magnetic and electrical properties of Sr2.9La0.1Sn1.9M0.1O7 (M= Cr, Mn or Fe) compounds. This La/M co-doping of the hybrid improper ferroelectric Sr3Sn2O7, allows introducing magnetic cations into the perovskite layers of this Ruddlesden-Popper phase. The doping induces minor structural changes, preserving the polar structure with space group A21am of the undoped compound. The perovskite tolerance factor of all doped samples is lower than in Sr3Sn2O7, which preserves larger tilts and rotations of SnO6 octahedra. Doped samples exhibit a paramagnetic behavior down to 5 K and obey the Curie-Weiss law above 200 K. The effective paramagnetic moments agree with the expected spin-only values of the respective magnetic M3+ cations. All samples show a ferroelectric hysteresis loop at room temperature, but the doped samples show larger coercive fields. Additionally, the doping with magnetic cations has important effects on the dielectric properties: a strong decrease of the temperature of the ferroelectric transition together with a smoothing of the anomaly in the dielectric permittivity. These results suggest that the disorder produced by the two aliovalent substitutions is detrimental for the ferroelectric properties due to point charge defects but, at the same time, the prevalence of the structural distortion (tilts and rotations) preserves the ferroelectricity in the investigated doping regime., Financial support from PID2021-124734OB-C21 funded by MCIN/AEI/10.13039/501100011033 and, as appropriate, by “ERDF A way of making Europe”, and from Gobierno de Aragón (Project E12-23R)., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Disclosing the magnetic ground state of PrBaMn2O6 [Dataset]

  • Blasco, Javier
  • Rodríguez-Velamazán, J. A.
  • García Muñoz, Josep Lluís
  • Subías, Gloria
Single-crystal neutron diffraction data were collected on the high resolution four-circle diffractometer D9 at the ILL (Grenoble, France) using the wavelength of 0.832(1) Å obtained by reflection from a Cu (220) monochromator. A small two-dimensional (2D) area detector of 6 × 6 cm (32 × 32 pixels) allows reciprocal space survey and optimization of the peak position., Magnetic measurements on powder samples were carried out between 5 and 400 K by using a commercial superconducting quantum interference device (SQUID) and a Physical Properties Measuring System (PPMS) from Quantum Design. The measurements were performed warming the sample after zero-field cooling at an external magnetic field of 1 kOe and then cooling in the same field. Isothermal magnetization measurements at 5 and 283 K (heating run) were performed for externals fields between -50 and 50 kOe., We here report a neutron diffraction study on a single crystal of the layered PrBaMn2O6 perovskite. This compound undergoes two consecutive magnetic transitions with decreasing temperature. At TC ≈ 309 K, a long-range ferromagnetic ordering is established with the Mn magnetic moments oriented along the c-axis. Below TN ≈ 240 K, a spin reorientation gives rise to a sudden decrease of the magnetization and the formation of an antiferromagnetic order. This magnetic transition is also accompanied by an electronic localization caused by a structural phase transition from a high temperature tetragonal phase (P4/mmm) into a low temperature orthorhombic one (P21am). Our neutron diffraction study at 12 K has unambiguously identified that the ground magnetic structure for this compound is a layered antiferromagnetic structure along the c-axis with the Mn moments oriented in the ab-plane along one diagonal of the primitive tetragonal cell. No sign of magnetic scattering associated to a CE-type magnetic structure was found in our study, discarding its occurrence in this compound. This result excludes the occurrence of a charge order transition to account for the electronic localization and it is fully consistent with previous structural studies showing a unique crystallographic site for Mn atom in the low temperature phase. A symmetry analysis was carried out to identify the magnetic space group of the ferromagnetic order above TN and the two possible groups for the antiferromagnetic ordering below TN., Financial support from PID2021-124734OB-C21 and RTI2018-098537-B-C22 funded by MCIN/AEI/10.13039/501100011033 and, as appropriate, by “ERDF A way of making Europe”, and “Severo Ochoa” Programme for Centres of Excellence in R&D (CEX2023-001282-S and CEX2023-001263-S); and from Gobierno de Aragón (Project E12-23R). Granted beam time at ILL (Experiment No. 5–41–1121)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001282-S)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001263-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Mn local structure and magnetic and thermal properties of A-site ordered RBaMn2O6 (R = La, Nd, Sm, and Y) [Dataset]

  • Subías, Gloria
  • Blasco, Javier
  • Cuartero, Vera
  • Lafuerza, Sara
  • Simonelli, Laura
  • Gorni, Giulio
  • Castro, Miguel
  • García, Joaquín
The degree of A-site disorder was checked with X-Ray powder diffraction (XRPD) measurements (YBaMn2O6_XRD_RT_FigS2.dat; SmBaMn2O6_XRD_RT_FigS2.dat; Y05Ba05MnO3_XRD_RT_FigS2.dat; Sm05Ba05MnO3_XRD_RT_FigS2.dat), using a RIGAKU D-max 2500 diffractometer at Cu Ka radiation within the 10-80° 2θ range., HERFD-XAS measurements at the Mn K-edge were performed at the CLAESS beamline of the ALBA Synchrotron (Cerdanyola del Vallès, Spain) using a Si (311) double-crystal monochromator. HERFD-XAS spectra were collected in back scattering geometry at the maximum of the Mn Kb1,3 (6490 eV) emission line using the CLEAR spectrometer. A liquid-N2 cryostat was used for the temperature-dependent measurements between 80 and 600 K., Standard transmission detected EXAFS spectra were recorded in the La and Y compounds and For RE = Nd and Sm, EXAFS spectra were obtained by recording simultaneously the HERFD-XAS at the Mn Kb1,3 line and the TFY-XAS spectra measured with a Si diode., DC Magnetization measurements, collected with a commercial QD SQUID between 5 and 400 K at an external magnetic field of 1 kOe for both ordered REBaMn2O6 and disordered RE0.5Ba0.5MnO3 series with RE=La, Nd and Sm. For the YBaMn2O6 and Y0.5Ba0.5MnO3 samples, the dc magnetization was measured between 5 and 700 K at 1 KOe and field-cooled magnetization at 1 kOe was also recorded for the Y0.5Ba0.5MnO3 compound., Calorimetric measurements were made in the ordered REBaMn2O6 (RE= Sm and Y) compounds using a Q2000 Differential scanning calorimeter (DSC) from TA instruments in the temperature range from 200 K to 575 K. Powder samples (between 10-40 mg) sealed in aluminum hermetic pans were heated and cooled at a scanning rate of 10 K/min., We have investigated the temperature dependence of the Mn local structure in A-site ordered RBaMn2O6 (R = La, Nd, Sm, and Y) perovskites, in parallel with their disordered counterparts, R0.5Ba0.5MnO3, by means of x-ray emission (XES) and x-ray absorption spectroscopy (XAS) The end member LaBaMn2O6 shows a nearly regular MnO6 octahedron independent of temperature. With decreasing the R ionic radius in the ordered samples, the XAS results indicate that a local distortion develops in theMnO6 octahedron at the low-temperature charge-localized and polar phases. For NdBaMn2O6, this local distortion is tiny, indicating the absence of charge segregation at the Mn site. This is followed by a bigger local distortion anticipated for SmBaMn2O6 in its respective charge-localized and polar phase and finally, the biggest local distortion for the smallest. A-site cation ordered compound, YBaMn2O6, for which it even persists above the polar charge-localization transition temperatures. The high-resolution XAS spectra confirm the presence of charge segregation between two nonequivalent Mn sites in the low-temperature polar phase of Sm and Y ordered samples. Thus, our XAS study suggests a displacive mechanism for the charge-localization and polar transitions in the Nd and Sm ordered samples while a combination of displacive and order-disorder contributions is revealed for YBaMn2O6. Besides, calorimetric measurements confirm the combination of the two mechanisms, order-disorder and displacive, for the ordered Sm and Y compounds. On the other hand, the A-site disordered R0.5Ba0.5MnO3 samples with R cations smaller than Nd present a significant static (temperature-independent) local disorder, which explains why polar charge-localization transitions are not developed in these samples. Finally, we correlate our results about the Mn local structure and character of the transitions with the macroscopic magnetic and electric behavior of both A-site ordered and disordered compounds., This work was funded by MICIU/AEI/10.13039/501100011033 and ERDF/UE (RTI2018-098537-B-C22, PID2021-124734OB-C21, FJC2020-044866-I)., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Mechanism behind the enhanced ferromagnetic contributions upon Ru substitution in Ca3Mn2O7 from X-ray absorption spectroscopies [Dataset]

  • Subías, Gloria
  • Cuartero, Vera
  • Herrero Martín, Javier
  • Lafuerza, Sara
  • Saveleva, Viktoriia A.
  • Glatzel, Pieter
  • Torchio, Raffaella
  • Mathon, Olivier
  • Blasco, Javier
TEY-detected XANES and XMCD measurements at the Mn-L2,3 and the Ru-L2,3 edges were performed at the HECTOR cryomagnet end station in the BL29 BOREAS beamline16 of the ALBA synchrotron. The XMCD signals were obtained by subtracting the XANES recorded using circular polarization with positive and negative helicities (μ+ and μ−, respectively) under a magnetic field of 6 T applied parallel to the beam propagation direction (or under no applied field). In all cases, the samples were kept at a temperature of 50 K. Ru L3 HERFD-XANES measurements were recorded using the in-vacuum TEXS spectrometer at the ID26 beamline of the ESRF synchrotron. The Ru L3 HERFD-XANES measurements were recorded by monitoring the intensity at the top of the Lα1 emission line (3d5/2 → 2p3/2 transition) using five Si (111) crystal analyzers. Mn and Ru K-edge XANES and EXAFS measurements were performed at the BM23 beamline at ESRF. Spectra were collected in transmission geometry by using ionization chambers as detectors. Magentic hysteresis loops were measured at 50 K between -5 and 5 T using a commercial superconducting quantum interference device (SQUID) magnetometer from Quantum Design., We have studied the local structure and electronic and magnetic properties of hybrid improper ferroelectric Ca3Mn2O7 upon Ru substitution at the Mn site by a combination of atomic-selective X-ray absorption spectroscopies in the soft and hard X-ray energy regimes. Ru substitution enhances the macroscopic ferromagnetic contributions, whose origin is here elucidated. In particular, soft X-ray magnetic circular dichroism (XMCD) data indicate that the spin moments of Mn and Ru are aligned in opposite directions, with the effective magnetic moments of Ru being about 1 order of magnitude smaller than for Mn. The XMCD results also demonstrate the presence of an intrinsic ferromagnetic component in the Mn sublattice for Ru contents x ≥ 0.3, although the values of the net Mn magnetic moment are much smaller than expected for a fully saturated Mn4+ magnetic sublattice. Soft and hard X-ray absorption spectroscopy measurements show that Mn keeps a +4 valence state independently of the Ru content, whereas Ru is in an intermediate valence state, ranging between +4.7 (x ≤ 0.1) and +4.4 (x ≥ 0.7). Analysis of the extended X-ray absorption fine structure (EXAFS) signals at the Mn and Ru K-edges suggests the lack of a complete solid solution in the local structure across the entire range of compositions. These findings disclose the existence of charge transfer between Mn and Ru atoms, so the weak ferromagnetic component is attributed to a canting of the antiferromagnetically ordered Mn4+ spins caused by the oxygen-mediated hybridization between localized Mn4+ 3d and itinerant intermediate valence Ru 4d bands, in analogy to the mechanism proposed for ferromagnetism in ordered doubled perovskites with 3d and 4d/5d transition-metal ions. In the present case, disorder prevents the formation of long-range ferromagnetism., This work was funded by MICIU/AEI/10.13039/501100011033 and ERDF/UE (PID2021-124734OB-C21, PID2021-124734OB-C22) and Gobierno de Aragón (project E12-23R)., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Three charge order phases in the bilayered Pr(Sr0.1Ca0.9)2Mn2O7 compound: from antiferrodistortive to ferrodistortive structures [Dataset]

  • Blasco, Javier;
  • Cuartero, Vera
  • Lafuerza, Sara
  • García Muñoz, Josep Lluís; ;
  • Fauth, François
  • Subías, Gloria
Synchrotron x-ray powder diffraction (SXRPD) patterns were recorded at the MSPD beam line of the Alba synchrotron (Cerdanyola del Vallès, Spain) using two experimental setups. The high angular resolution Multi Analyzer Detector (MAD) coupled to a Dynaflow liquid He cryostat was used to collect SXRPD patterns at selected temperatures (30, 60, 80, 100, 120, 150 and 180 K). The high-throughput position sensitive detector MYTHEN which owing to its exceptional dynamic range allows to detect minor superstructure peaks was used to continuously collect patterns from 100 up to 400 K coupled to an Oxford cryostream to control the temperature. In both cases, the samples were loaded in a borosilicate glass capillary (diameter of 0.7 mm) and kept spinning during data acquisition. A short wavelength, λ=0.4133 Å, was selected to optimize absorption. Magnetic measurements were carried out with a commercial Quantum Design (SQUID) magnetometer. The dc magnetization was measured between 5 and 400 K with an external field of 1 kOe in a single crystal with the magnetic field parallel and perpendicular to the c-direction., The structural phase transitions of Pr(Sr0.1Ca0.9)2Mn2O7 have been studied by synchrotron radiation x-ray powder diffraction. Three different charge order (CO) phases are identified as a function of temperature. The three phases have a checkerboard arrangement of compressed and expanded MnO6 octahedrons in the perovskite bilayers. The structural changes associated to each transition are described in terms of the mode decomposition analysis with respect to the parent tetragonal structure. The high temperature phase exhibits an orthorhombic symmetry (Amam) due to cooperative tilts of the MnO6 octahedrons that can be ascribed to the irreducible representation (irrep) X3-. On cooling, the CO1 phase with Pbnm symmetry arises from the condensation of modes belonging to the irrep DT2 together with breathing (X1+) and antiferrodistortive (M5- and Y2) modes. Mn site is split into two non-equivalent Mn atoms (Mn1 and Mn2) with a small charge segregation and the asymmetric environment of Mn1 atoms form zig-zag chains along the b-axis, that is doubled. Further cooling leads to the formation of the CO2 phase that comes from a relative change between the directions of previous X3- and DT2 distortions producing the simultaneous condensation of new DT1 and ferrodistortive GM5- modes. In the CO2 structure (Am2m symmetry), Mn2 atoms are split into two non-equivalent sites but with similar oxidation state. Then, the checkerboard arrangement between Mn1 and Mn2 atoms is preserved but with a reorientation of the zig-zag chains along the a-axis. At lower temperatures, the CO3 phase arises from a new direction change of irrep X3- leading to the simultaneous condensation of new secondary modes. Its symmetry is Pn21m and the Mn1 site is now split which leads to a total of four non-equivalent Mn sites in the unit cell. In this phase, more tilts of the MnO6 octahedrons are allowed following the a-b-c+ tilt schema., Financial support from the Spanish Ministerio de Ciencia, Innovación y Universidades (Projects No. PID2021-124734OB-C21 and –C22 cofunded by ERDF from EU, and Severo Ochoa FUNFUTURE, CEX2019-000917-S),Gobierno de Aragón (Project E12-23R) and Generalitat de Catalunya (Project 2021 SGR 445). Granted beam time at ALBA synchrotron (proposal No. 2018093038)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2019-000917-S)., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

The electrocaloric effect of lead-free Ba1−yCayTi1−xHfxO3 from direct and indirect measurements [Dataset]

  • Gracia, David
  • Lafuerza, Sara
  • Blasco, Javier
  • Evangelisti, Marco
Crystal structures were characterized by powder X-ray diffraction (XRD) at room temperature in a Rigaku D-Max system using Cu Kα1,2 wavelengths. Rietveld analysis of the X-ray patterns was performed using the Fullprof package program. Electrical and electrocaloric properties measurements were conducted on sintered disc-shaped samples, with typical dimensions of 8 mm diameter and thickness between 0.5 and 1.5 mm. Electrodes were made with silver paste in sandwich geometry. The dielectric constant was derived from measurements with an impedance analyzer (Wayne Kerr Electronics 6500B), applying sinusoidal excitations of 1 V amplitude at several frequencies between 100 Hz and 4 MHz. The polarization versus electric field P(E) curves were recorded using a commercial polarization analyzer (aixACCT Easy Check 300) jointly with a high voltage amplifier (Trek 610E), applying sinusoidal excitations with typical frequency of 10 Hz and E field amplitudes up to 25 kV/cm. Direct measurements of the electrocaloric effect (ECE) were performed using a dedicated in-house-developed quasi-adiabatic calorimeter. The adiabatic temperature change was measured as a function of temperature every 1 K and at different applied E field variations. Samples were measured in the “contactless” mode to minimize heat losses, held only by the high voltage coaxial cable and K-type thermocouple for the direct measurement of the temperature variation. Voltages up to 2 kV were applied using two different homemade high-voltage converters., We report on the dielectric and electrocaloric properties of Ba1−yCayTi1−xHfxO3 for compositions 0.12 < x < 0.18 and y = 0.06, as well as x = 0.15 and 0 < y < 0.15, synthesized by the conventional solid-state reaction method. The addition of Hf/Ca broadens the ferroelectric-paraelectric phase transition while moving it toward room temperature. Two interferroelectric transitions are seen to converge, together with the ferroelectric–paraelectric phase transition, at ∼335 K for 0.12 < xc < 0.135 and y = 0.06. Consistent with the dielectric properties, the electrocaloric effect maximizes closer to room temperature with increasing Hf/Ca substitutions, which promote larger temperature spans. The electrocaloric responsivity gradually decreases from 0.2 to 0.1 K mm kV−1 with the addition of Hf/Ca. A homemade quasi-adiabatic calorimeter is employed to measure “directly” the electrocaloric data, which are also calculated from polarization-versus-electric-field cycles using “indirect” standard procedures. The comparison between measured and calculated values highlights the importance of having access to direct methods for a reliable determination of the electrocaloric effect., Ministerio de Ciencia, Innovación y Universidades (PID2021-124734OB-C21); Diputación General de Aragón (E11-23R, E12-23R)., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Triple-point phase diagrams for BTO-based ceramics [Dataset]

  • Gracia, David
  • Fauth, François
  • Lafuerza, Sara
  • Evangelisti, Marco
  • Blasco, Javier
Crystal structures were characterized by SXRPD experiments as a function of temperature. Data were collected on the Material Science and Powder Diffraction (MSPD) beamline at the ALBA Synchrotron using 0.41368 A wavelength. Rietveld analysis of the X-ray patterns was performed using the Fullprof package program. The dielectric constant was derived from measurements with an impedance analyzer (Wayne Kerr Electronics 6500B), applying sinusoidal excitations of 1 V amplitude at a frequency of 50 kHz. Measurements were conducted on sintered disc-shaped samples, with typical dimensions of 8 mm diameter and thickness between 0.5 and 1.5 mm. Electrodes were made with silver paste in sandwich geometry., The temperature-composition structural phase diagram of the BTO-based ferroelectric system Ba0.94Ca0.06Ti1−xHfxO3 (0.05 ≤ x ≤ 0.15) is investigated using high-angular resolution synchrotron X-ray powder diffraction and dielectric permittivity measurements. In contrast to the well-known structural phase transition sequence of the parent compound BaTiO3 (rhombohedral → orthorhombic → tetragonal → cubic, upon heating), Hf4+ doping into Ba0.94Ca0.06Ti1−xHfxO3 results in the gradual disappearance of the intermediate orthorhombic and tetragonal phases at two different, but close, critical concentrations, 0.10 < xc1 < 0.12 and 0.12 < xc2 < 0.135, respectively, revealing the presence of two triple points in the phase diagram., Ministerio de Ciencia, Innovación y Universidades (PID2021-124734OB-C21); Diputación General de Aragón (E11-23R, E12-23R). Granted beam time at ALBA Synchrotron (Proposal No. 2023027380)., Peer reviewed