Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

The electrocaloric effect of lead-free Ba1−yCayTi1−xHfxO3 from direct and indirect measurements

  • Gracia, David
  • Lafuerza, Sara
  • Blasco, Javier
  • Evangelisti, Marco
We report on the dielectric and electrocaloric properties of Ba1−yCayTi1−xHfxO3 for compositions 0.12 < x < 0.18 and y = 0.06, as well as x = 0.15 and 0 < y < 0.15, synthesized by the conventional solid-state reaction method. The addition of Hf/Ca broadens the ferroelectric-paraelectric phase transition while moving it toward room temperature. Two interferroelectric transitions are seen to converge, together with the ferroelectric–paraelectric phase transition, at ∼335 K for 0.12 < xc < 0.135 and y = 0.06. Consistent with the dielectric properties, the electrocaloric effect maximizes closer to room temperature with increasing Hf/Ca substitutions, which promote larger temperature spans. The electrocaloric responsivity gradually decreases from 0.2 to 0.1 K mm kV−1 with the addition of Hf/Ca. A homemade quasi-adiabatic calorimeter is employed to measure “directly” the electrocaloric data, which are also calculated from polarization-versus-electric-field cycles using “indirect” standard procedures. The comparison between measured and calculated values highlights the importance of having access to direct methods for a reliable determination of the electrocaloric effect., This work was supported by MICINN (Project No. PID2021-124734OB-C21) and DGA (Grant Nos. E11-23R and E12-23R). S.L. acknowledges funding from the European Union’s Horizon 2020 research and innovation program under Marie Skłodowska–Curie Grant Agreement No. 101029019. D.G. acknowledges financial support from the Gobierno de Aragón through a doctoral fellowship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Electrocaloric effect near room temperature in lead-free Aurivillius phase Sr2Bi4Ti5O18 upon La and Nb codoping

  • Lafuerza, Sara
  • Gracia, David
  • Blasco, Javier
  • Evangelisti, Marco
La and Nb codoping of ferroelectric five-layer Aurivillius phase Sr2Bi4Ti5O18 (TC ~ 560 K), induces compositional disorder and diffuse relaxor transitions at much lower temperatures than the parent compound, while preserving the orthorhombic structure. For moderate La and Nb concentrations, the ferroelectric properties are enhanced in the vicinity of room temperature, and so is the electrocaloric effect as measured directly with a homemade quasi-adiabatic calorimeter. The adiabatic temperature change reaches, e.g., in Sr2Bi3.44La0.5Ti4.8Nb0.2O18, ΔT ⁓ 0.3 K at 355 K with a temperature span ⁓ 15 K, under ΔE = 37 kV/cm. Besides, a large field dispersion of the electrocaloric effect is found, ascribed to field-induced transitions from short-range-ordered relaxor to long-range-ordered ferroelectric states. Indirect estimations of the electrocaloric effect from electric polarization data are not able to quantitatively predict the direct results and emphasize the need of applying direct measurement methods, especially for relaxor ferroelectrics., S. L. acknowledges funding from the European Union’s Horizon 2020 research and innovation program under the Marie Skłodowska-Curie grant agreement No. 101029019. This work was also supported by Ministerio de Ciencia, Innovación y Universidades (PID2021-124734OB-C21) and Diputación General de Aragón (E11-23R, E12-23R). D. G. acknowledges financial support from the Gobierno de Aragón through a doctoral fellowship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

High-quality epitaxial five-layer Aurivillius films with in-plane ferroelectricity for electrocaloric cooling

  • Lafuerza, Sara
  • Blasco, Javier
  • Evangelisti, Marco
  • Subías, Gloria
  • Gracia, David
  • Pardo, José M.
  • Barriuso, Eduardo
  • Torrelles, Xavier
  • Padilla Pantoja, Jessica
  • Caicedo, José Manuel
  • Santiso, José
High-quality purely c-axis oriented epitaxial thin films of the Aurivillius phase Sr2Bi4Ti5O18 with n = 5 (Sr,Bi)TiO3 perovskite-like layers, are grown on SrTiO3 substrates by pulsed laser deposition. The highest crystalline quality is obtained with a 20 wt.% Bi-excess target and average stacking order values in the proximity of the ideal value n = 5 are attained for an optimum deposition temperature of 650 °C. Scanning transmission electron microscopy reveals regions with n ranging from 4 to 6 around an average thickness of n = 5, in agreement with the X-ray diffraction analysis. Interdigital electrodes are used to probe the in-plane polarization and survey the electrocaloric properties. A maximum adiabatic temperature change of ΔT ∼ 0.95 °C for an electric field of 150 kV cm−1 is observed at ≈135 °C. Larger values are expected at higher temperatures around the ferroelectric Curie temperature, TC. Since TC of Sr2Bi4Ti5O18 can be tuned by codoping, the findings pave the way toward a large electrocaloric effect at ambient temperature., S.L. acknowledges funding from the European Union's Horizon 2020 research and innovation program under the Marie Skłodowska-Curie grant agreement No. 101029019. This work was also supported by Ministerio de Ciencia, Innovación y Universidades (PID2021-124734OB-C21), “Severo Ochoa” Programme for Centres of Excellence in R&D (CEX2023-001286-S, CEX2023-001263-S and CEX2021-001214-S) and Diputación General de Aragón (E11-23R, E12-23R). D. G. acknowledges financial support from the Gobierno de Aragón through a doctoral fellowship. Authors would like to acknowledge C. Cosculluela from Unidad Técnica en Ingeniería de Microdispositivos (INMA) and R. Valero for the IDEs fabrication at the National Facility ELECMI ICTS, node “Laboratorio de Microscopías Avanzadas”, through Servicio General de Apoyo a la Investigación from Universidad de Zaragoza. The authors also acknowledge the use of instrumentation as well as the technical advice provided by the Joint Electron Microscopy Center at ALBA (JEMCA) and funding from Grant IU16-014206 (METCAM-FIB) to ICN2 funded by the European Union through the European Regional Development Fund (ERDF), with the support of the Ministry of Research and Universities, Generalitat de Catalunya. J. S. acknowledges B. Mundet, F. Belarre and M. Rosado for the STEM images and FIB fabrication of the lamellas, as well as the financial support of the European Commission through the Horizon H2020 funding by H2020-MSCA-RISE-ID:101007825 –ULTIMATE-I. X. T. acknowledges financial support by Ministerio de Ciencia, Innovación y Universidades (PID2021-123276OB-I00)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2023-001263-S)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2023-001286-S)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2021-001214-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

High-quality epitaxial five-layer Aurivillius films with in-plane ferroelectricity for electrocaloric cooling [Dataset]

  • Lafuerza, Sara
  • Blasco, Javier
  • Evangelisti, Marco
  • Subías, Gloria
  • Gracia, David
  • Pardo, José A.
  • Barriuso, Eduardo
  • Torrelles, Xavier
  • Padilla-Pantoja, Jessica
  • Caicedo, José Manuel
  • Santiso, José
[Description of methods used for collection/generation of data]: The structural characterization of the films was performed by X-ray diffraction (XRD) 2θ/ω wide scans, X-ray reflectivity (XRR) and reciprocal space maps (RSMs) of selected asymmetric reflections, by using a four-circle X-ray diffractometer (Malvern-Panalytical X'pert Pro MRD) and standard Cu Kα1,2 X-ray source with a parabolic mirror (for reciprocal space maps, a 2xGe(220) monochromator was added to the incident optics). A 2D array PIXcel detector was used. The topography of selected films was studied using atomic force microscopy (AFM) in contact mode (Keysight 5100) over different areas. The structure of the films was also analyzed by high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) on a Fisher Spectra microscope operated at 200 kV. Cross-section lamellas were prepared by focused ion beam (FIB) on a SBTO5 film deposited under optimized conditions, with the cut oriented to show STO [100] zone axis., [Ferroelectric and Electrocaloric Properties]: These properties were investigated by measuring the in-plane polarization using the IDEs with a 500 V-built-in ferroelectric tester (Precision Premier II model, Radiant Technologies). Hysteresis measurements were carried out based on a bipolar triangular wave excitation, and also remanent hysteresis measurements based on half triangular waves following the principle of the positive-up negative-down (PUND) method. The frequency of the triangular wave excitation was set to 2 kHz for both measurement protocols. Temperature (T)-dependent polarization versus E field, P(E, T) curves, were measured on heating in a dedicated homemade cell allowing a maximum temperature of 140 °C. Samples were immersed in a silicon oil bath during the polarization measurements to avoid electric discharges., High-quality purely c-axis oriented epitaxial thin films of the Aurivillius phase Sr2Bi4Ti5O18 with n = 5 (Sr,Bi)TiO3 perovskite-like layers, are grown on SrTiO3 substrates by pulsed laser deposition. The highest crystalline quality is obtained with a 20 wt.% Bi-excess target and average stacking order values in the proximity of the ideal value n = 5 are attained for an optimum deposition temperature of 650 °C. Scanning transmission electron microscopy reveals regions with n ranging from 4 to 6 around an average thickness of n = 5, in agreement with the X-ray diffraction analysis. Interdigital electrodes are used to probe the in-plane polarization and survey the electrocaloric properties. A maximum adiabatic temperature change of ΔT ∼ 0.95 °C for an electric field of 150 kV cm−1 is observed at ≈135 °C. Larger values are expected at higher temperatures around the ferroelectric Curie temperature, TC. Since TC of Sr2Bi4Ti5O18 can be tuned by codoping, the findings pave the way toward a large electrocaloric effect at ambient temperature., S.L. acknowledges funding from the European Union's Horizon 2020 research and innovation program under the Marie Skłodowska-Curie grant agreement No. 101029019. This work was also supported by Ministerio de Ciencia, Innovación y Universidades (PID2021-124734OB-C21), “Severo Ochoa” Programme for Centres of Excellence in R&D (CEX2023-001286-S, CEX2023-001263-S and CEX2021-001214-S) and Diputación General de Aragón (E11-23R, E12-23R). D. G. acknowledges financial support from the Gobierno de Aragón through a doctoral fellowship. Authors would like to acknowledge C. Cosculluela from Unidad Técnica en Ingeniería de Microdispositivos (INMA) and R. Valero for the IDEs fabrication at the National Facility ELECMI ICTS, node “Laboratorio de Microscopías Avanzadas”, through Servicio General de Apoyo a la Investigación from Universidad de Zaragoza. The authors also acknowledge the use of instrumentation as well as the technical advice provided by the Joint Electron Microscopy Center at ALBA (JEMCA) and funding from Grant IU16-014206 (METCAM-FIB) to ICN2 funded by the European Union through the European Regional Development Fund (ERDF), with the support of the Ministry of Research and Universities, Generalitat de Catalunya. J. S. acknowledges B. Mundet, F. Belarre and M. Rosado for the STEM images and FIB fabrication of the lamellas, as well as the financial support of the European Commission through the Horizon H2020 funding by H2020-MSCA-RISE-ID:101007825 –ULTIMATE-I. X. T. acknowledges financial support by Ministerio de Ciencia, Innovación y Universidades (PID2021-123276OB-I00)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001263-S)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001214-S)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

The electrocaloric effect of lead-free Ba<sub>1-y Ca<sub>y Ti<sub>1-x Hf<sub>x O<sub>3 from direct and indirect measurements

  • Gracia, David
  • Lafuerza, Sara
  • Blasco, Javier
  • Evangelisti, Marco
We report on the dielectric and electrocaloric properties of Ba1−yCayTi1−xHfxO3 for compositions 0.12 < x< 0.18 and y = 0.06, as well as x = 0.15 and 0 < y < 0.15, synthesized by the conventional solid-state reaction method. The addition of Hf/Ca broadens the ferroelectric-paraelectric phase transition while moving it toward room temperature. Two interferroelectric transitions are seen to converge, together with the ferroelectric–paraelectric phase transition, at ∼335 K for 0.12 < x<sub>c < 0.135 and y = 0.06. Consistent with the dielectric properties, the electrocaloric effect maximizes closer to room temperature with increasing Hf/Ca substitutions, which promote larger temperature spans. The electrocaloric responsivity gradually decreases from 0.2 to 0.1 K mm kV<sup>−1 with the addition of Hf/Ca. A homemade quasi-adiabatic calorimeter is employed to measure “directly” the electrocaloric data, which are also calculated from polarization-versus-electric-field cycles using “indirect” standard procedures. The comparison between measured and calculated values highlights the importance of having access to direct methods for a reliable determination of the electrocaloric effect.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Electrocaloric effect near room temperature in lead-free Aurivillius phase Sr2Bi4Ti5O18 upon La and Nb codoping

  • Lafuerza, Sara
  • Gracia, David
  • Blasco, Javier
  • Evangelisti, Marco
La and Nb codoping of ferroelectric five-layer Aurivillius phase Sr2Bi4Ti5O18 ( ∼ 560 K), induces compositional disorder and diffuse relaxor transitions at much lower temperatures than the parent compound, while preserving the orthorhombic structure. For moderate La and Nb concentrations, the erroelectric properties are enhanced in the vicinity of room temperature, and so is the electrocaloric effect as measured directly with a homemade quasi-adiabatic calorimeter. The adiabatic temperature change reaches, e.g., in Sr2Bi3.44La0.5Ti4.8Nb0.2O18, ⁓ 0.3 K at 355 K with a temperature span ⁓ 15 K, under = 37 kV/cm. Besides, a large field dispersion of the electrocaloric effect is found, ascribed to field-induced transitions from short-range-ordered relaxor to long-range-ordered ferroelectric states. Indirect estimations of the electrocaloric effect from electric polarization data are not able to quantitatively predict the direct results and emphasize the need of applying direct measurement methods, especially for relaxor ferroelectrics.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High‐quality epitaxial five‐layer aurivillius films with in‐plane ferroelectricity for electrocaloric cooling

  • Lafuerza, Sara
  • Blasco, Javier
  • Evangelisti, Marco
  • Subías, Gloria
  • Gracia, David
  • Pardo, José Á.
  • Barriuso, Eduardo
  • Torrelles, Xavier
  • Padilla-Pantoja, Jessica
  • Caicedo, José M.
  • Santiso, José
High‐quality purely c‐axis oriented epitaxial thin films of the Aurivillius phase Sr2Bi4Ti5O18 with n = 5 (Sr,Bi)TiO3 perovskite‐like layers, are grown on SrTiO3 substrates by pulsed laser deposition. The highest crystalline quality is obtained with a 20 wt.% Bi‐excess target and average stacking order values in the proximity of the ideal value n = 5 are attained for an optimum deposition temperature of 650 °C. Scanning transmission electron microscopy reveals regions with n ranging from 4 to 6 around an average thickness of n = 5, in agreement with the X‐ray diffraction analysis. Interdigital electrodes are used to probe the in‐plane polarization and survey the electrocaloric properties. A maximum adiabatic temperature change of ΔT ∼ 0.95 °C for an electric field of 150 kV cm−1 is observed at ≈135 °C. Larger values are expected at higher temperatures around the ferroelectric Curie temperature, TC. Since TC of Sr2Bi4Ti5O18 can be tuned by codoping, the findings pave the way toward a large electrocaloric effect at ambient temperature.