Skip to main content

NUEVAS ESTRATEGIAS PARA EL DESARROLLO DE CATALIZADORES HIBRIDOS NANOESTRUCTURADOS PARA LA HIDROGENACION DIRECTA SELECTIVA DE CO2 A DME

PID2019-111219RB-I00

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Call year 2019
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hydrogenation of CO2 to Valuable C2-C5 Hydrocarbons on Mn-Promoted High-Surface-Area Iron Catalysts

  • Zepeda, Trino A.
  • Aguirre, Sandra
  • Galindo-Ortega, Yunuen I.
  • Solís-García, Alfredo
  • Navarro Yerga, Rufino Manuel
  • Pawelec, Bárbara
  • Fierro-González, Juan C.
  • Fuentes, Sergio
Mn-promoted bulk iron catalysts with a high specific surface area (82–211 m2·g−1) were synthesized by coprecipitation followed by drying under supercritical conditions. The catalysts were tested in the CO2 hydrogenation to valuable C2-C5 hydrocarbons. The Mn-promoted iron catalysts exhibited better textural properties than the bare Fe2O3 catalyst, allowing better dispersion of the active phase, easier reduction and carburization of iron oxides and, consequently, resulting in higher catalytic activity than the bare Fe2O3 catalyst. The best activity results were obtained by catalyst promotion with a very low amount of Mn (Mn/Fe atomic ratio of 0.05). Upon steady state conditions (T = 340 °C, total pressure of 20 bar and H2/CO2 = 3), this catalyst exhibited high CO2 conversion (44.2%) and selectivity to C2-C4 hydrocarbons (68%, olefin to paraffin ratio of 0.54), while the selectivity to C5+ hydrocarbons, CH4 and CO was about 3.2, 38.5 and 5%, respectively. A close correlation was found between catalyst textural properties and CO2 conversion. The most active MnFe-0.05 catalyst exhibited high stability during 72 h of reaction related to a low amount of soft coke formation and catalyst activation through the formation of the χ-Fe5C2 phase during the on-stream reaction., R.M.N.Y. and B.P. gratefully acknowledge financial support from the Ministry of Science, Innovation and Universities (PID2019-111219RB-100 project) and the Spanish National Research Council (C.S.I.C.). T.A. Zepeda and S. Fuentes gratefully acknowledge financial support from CONACyT under the projects 117373 and IN112922., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Improved Dimethyl Ether Production from Syngas over Aerogel Sulfated Zirconia and Cu-ZnO(Al) Bifunctional Composite Catalysts

  • Lassoued, Hela
  • Mota Toledo, Noelia
  • Millán, Elena
  • Raissi, Sahar
  • Younes, Mohamed Kadri
  • Quilis Romero, Carlos
  • Navarro Yerga, Rufino Manuel
This work is dedicated to the study of the effect of the synthesis conditions (drying and calcination) of sulfated zirconia on the final catalytic behavior of bifunctional composite catalysts prepared by the physical mixing of the sulfated zirconia (methanol dehydration catalyst) with Cu/ZnO/Al2O3 (CZA; methanol synthesis catalyst). The main objective was to optimize the CZA-ZrO2/SO42− composite catalyst for its use in the direct production of dimethyl ether (DME) from syngas. Sulfated zirconia aerogel (AZS) and xerogel (XZS) were prepared using the sol–gel method using different solvent evacuation conditions and calcination temperatures, while the Cu-ZnO(Al) catalyst was synthesized using the coprecipitation procedure. The effectivity of CZA-ZrO2/SO42− composite catalysts for the direct production of dimethyl ether (DME) from syngas was evaluated in a flow reactor at 250 °C and 30 bar total pressure. The characterization of the sulfated zirconia aerogels and xerogels using different techniques showed that the mesoporous aerogel (AZS0.5300) exhibited the best textural and acidic properties due to the gel drying under supercritical conditions and calcination at 300 °C. As a result, the composite catalyst CZA-AZS0.5300 exhibited seven times higher DME production than its xerogel-containing counterpart (364 vs. 52 μmolDME·min−1·gcat−1). This was attributed to its well-matched metal surface, mesoporous structure, optimal crystallite size and, most importantly, its higher acidity., he authors gratefully acknowledge the financial support provided by the Tunisian Ministry of Higher Education and Scientific Research and by the research programs PID2019–111219RB-100 and PID 2022-143180OB-I00 supported by the Spanish Ministry of Science, Innovation and Universities. E.M.O. and C.Q.R. would like to acknowledge the FPI programme of the Spanish Ministry of Science, Innovation and Universities for their research grants (PRE2020-094027 and BES-2017-080240)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Application of Intermetallic Compounds as Catalysts for the Selective Hydrogenation of CO2 to Methanol

  • Quilis Romero, Carlos
  • Mota Toledo, Noelia
  • Millán, Elena
  • Pawelec, Bárbara
  • Navarro Yerga, Rufino Manuel
Direct catalytic conversion of CO2 to methanol via renewable hydrogen has emerged as a promising technology among the various CO2 conversion techniques. However, efficient hydrogenation of CO2 using conventional Cu-ZnO-based catalysts, which are currently used for industrial methanol production from synthesis gas, remains a challenge due to inefficient energy conversion, poor stability and sluggish CO2 conversion kinetics. As the catalytic activity, stability and methanol selectivity of conventional Cu/ZnO catalysts are still insufficient for industrial applications, novel catalyst formulations using transition metals/metal oxides and supported noble metal nanostructures have emerged. Among them, intermetallic compounds are being explored for their unique electronic and crystalline structures, which can be tailored by controlled, precise, and seamless tuning of interatomic distances, specific arrangements and electronic structure to enhance their stability and activity for the selective hydrogenation of CO2 to methanol. In this context, intermetallic catalysts containing Pd, Cu and Ni combined with metal oxide nanoparticles (ZnO, Ga2O3, In2O3, etc.) have been shown to be more effective than the classical Cu-ZnO-Al2O3. This review analyses the progress made in the study of these intermetallic catalysts by analysing different aspects of their preparation, characterization, effects of promoters, support interactions, etc. Future research perspectives are discussed in the context of potential industrial applications of intermetallics for direct methanol production via CO2 hydrogenation., The authors gratefully acknowledge the financial support provided by the Spanish Ministry of Science, Innovation and Universities through the research programs PID2022-1434800b-I00 and PID2019-111219RB-100. Carlos Quilis (PRE2020-094027) and and Elena Millán (BES-2017-080240) would like to acknowledge the FPI programme of the Spanish Ministry of Science, Innovation and Universities for their research grants., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of TiO2 on Acidity and Dispersion of H3PW12O40 in Bifunctional Cu-ZnO(Al)-H3PW12O40/TiO2 Catalysts for Direct Dimethyl Ether Synthesis

  • Millán, Elena
  • Mota Toledo, Noelia
  • Revel, Bertrand
  • Lafon, Olivier
  • Navarro Yerga, Rufino Manuel
The performance of bifunctional hybrid catalysts based on phosphotungstic acid (H3PW12O40, HPW) supported on TiO2 combined with a Cu-ZnO(Al) catalyst in the direct synthesis of dimethyl ether (DME) from syngas has been investigated. In this work, different types of TiO2 were used as a support to study the effect of changes in the structure of the TiO2 support on the acidity and dispersion of HPW. Various TiO2 supports with different structural and surface characteristics have been studied and the results indicate that: (i) the crystallinity and crystallite size of the primary particles of the HPW units depend on the TiO2 support; (ii) the pore size distribution of the TiO2 support affects the surface segregation of the heteropolyacids; and (iii) changes in the supported HPW acid catalysts do not significantly alter the crystal structure of the CuO and ZnO phases after contact with CZA in bifunctional catalysts. The activity results indicate that the variation in the intrinsic activity of the Cu-ZnOx centers in the bifunctional catalysts for direct DME synthesis is minimal due to the limited alteration of the crystal structure of the centers., The authors gratefully acknowledge the financial support provided by the Spanish Ministry of Science, Innovation and Universities through the research programs PID2022-1434800b-I00 and PID2019-111219RB-100. Elena Millán (BES-2017-080240) would like to acknowledge the FPI program of the Spanish Ministry of Science, Innovation and Universities for the research grant. The Chevreul Institute is thanked for supporting CPER projects funded by the “Ministère de l’Enseignement Supérieur et de la Recherche”, the region “Hauts-de-France”, the ERDF program of the European Union and the “Métropole Européenne de Lille”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Improved phenol degradation by catalytic wet air oxidation on the Co3O4 spinel catalysts supported on SBA-15 modified with TiO2

  • López-Chico, D. Y.
  • Pérez-Vidal, H.
  • Torres, G.
  • Lunagómez, M. A.
  • Pawelec, B.
  • Navarro Yerga, R. M.
  • Vázquez-Salas, P. J.
  • Zepeda, T. A.
The removal of phenol from aqueous industrial effluents by catalytic wet-air oxidation (CWAO) is a challenging process that requires novel catalysts resistant to leaching of the active phases during residence time in a batch reactor. In this sense, this work demonstrated that this can be archived with the catalyst having the spinel phase Co3O4 supported on mesoporous silica SBA-15 doped with an optimized amount of TiO2 (3 wt%). In the phenol CWAO reaction carried out at 160 °C and 10 bar O2, this best Co3O4/TiO2/SBA-15 catalyst showed an increase of phenol conversion from 49.0 % to 68.3 % and of CO2 selectivity from 87 % to 98 %. The extensive catalyst characterization and overall activity results indicated that this was related to the strength and nature of the acid sites and the oxidation states of the cobalt oxide phases. Combined factors influenced the final behaviour of the catalyst, such as its intrinsic activity, dispersion of the active phase, inhibition of CoSiO4 phase formation, high Lewis acidity and the large amount of active Co3O4 spinel phase. The presence of TiO2 nanoparticles (NPs) decorating the support surface improved the stability of the catalyst by inhibiting the leaching of cobalt species during the reaction. After three reaction cycles, the most efficient Co/3Ti/S15 catalyst showed high CO2 selectivity (∼92.7 %) and low selectivity towards carboxylic acid (∼5.3 %) and polyphenolic compounds (∼2%). It is proposed that surface oxidation is the rate-determining step in the CWAO reaction over TiO2/SBA-15-supported Co3O4 spinel catalysts., T.A. Zepeda thanks DGAPA-UNAM (IN112922, IN101523 and IA100822 projects) and CONACYT (F003 117373 project) for their financial support. The authors thank F. Ruiz, D. Dominguez, E. Flores, J. Mendoza, I. Gradilla and E. Aparicio for technical assistance. R.M. Navarro Yerga and B. Pawelec thank the Spanish Ministry of Science, Innovation and Universities for financial support through research program PID2019-111219RB-100., Peer reviewed