Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RUC. Repositorio da Universidade da Coruña
Publication Artículo científico (JournalArticle)

Effect of aggregate content and fibre type on the rheological behaviour and structural build-up of fibre reinforced self-compacting concrete using two binder compositions

  • Rojo-López, Gemma
  • González-Fonteboa, Belén
  • Martínez-Abella, Fernando
  • Seara Paz, Sindy
[Abstract:] Many parameters influence the fresh behaviour of fibre reinforced self-compacting concrete (FRSCC), such as length, aspect ratio, fibre content, solid volume fraction, and particle interaction. Most studies did not analyse rheological behaviour (just workability) and they are focused on paste or mortar. However, the analysis at the concrete level is also required to confirm the behaviour when the coarse aggregates and fibres are employed. This kind of analysis is scarce in the literature. Hence, this work aims to increase the knowledge about the effect of aggregate content and fibre type on FRSCC. To do so, the behaviour of self-compacting mixes with three different aggregate contents (550, 500, and 650 l/m3), two cementitious systems (100 % cement, and 60 % cement, 25 % limestone filler and 15 % metakaolin), and three different types of rigid fibres (two metallic and one polypropylene) were analysed. To characterise the concrete rheological performance, the stress growth test (SGT) was selected to avoid any fibre orientation. SGT was repeated twice under undisturbed and disturbed conditions to assess the structural build-up of the concrete. The results indicate that there is a critical value of the relative packing fraction that, once overcome, severely affects the fresh behaviour of FRSSC. This critical value can be calculated as the ratio between random loose packing fraction and dense packing fraction. It can be used to design a FRSCC mix guaranteeing that the fresh state remains in a suitable range where the hydrodynamic interactions dominate the behaviour and therefore, changes in the mix composition will not sharply modify the rheological performance of the concrete., This research was funded by the Spanish Ministerio de Ciencia e innovación - Agencia Estatal de investigación through three projects entitled: “Design of sustainable concrete for 3D printing based on rheology and on the control of very early properties (Eco3DConcrete)- PID2020–115433RB-I00”, “Design of concrete precast elements incorporating sustainable strategies for self-healing to increase their service life (PREHEALING)- PDC2021–121660-I00” and "Exploiting the synergic effects between 3D printing and self-healing technologies to design sustainable and durable concrete (3DHealConcrete) - TED2021–129757B-I00"
RUC. Repositorio da Universidade da Coruña
Publication Tesis doctoral (DoctoralThesis)

Research and New Smart Techniques on the Characterisation of New Self-compacting Concrete with Industrial Wastes and Fibres to Increase its Sustainability and Service Life, Investigación e novas técnicas intelixentes na caracterización de novos formigóns autocompactantes con residuos industriais e fibras para aumentar a súa sustentabilidade e vida útil

  • Rojo-López, Gemma
[Resumo] Este traballo aborda o desenvolvemento de mesturas autocompactantes coa incorporación de materiais suplementarios procedentes de residuos industriais como substitutos de cemento para aumentar a sustentabilidade, así como a introdución de fibras para aumentar a vida útil das mesturas. Estes materiais propostos son cinza de biomasa e po de granito, que se consideran residuos industriais na "Eurorrexión Galicia-Norte de Portugal" e son abundantes. Dada a crecente presión social cara á xestión sostible dos residuos e a eficiencia dos recursos, o uso destes materiais suplementarios procedentes de residuos industriais axuda a alcanzar os obxectivos de mitigación de CO2 avanzando cara a unha economía circular. Neste sentido, este estudo desenvolveuse a nivel de pasta, morteiro e formigón, deseñando diferentes mesturas de base cemento e analizando o seu comportamento mediante técnicas de extracción de coñecemento e reoloxía para obter parámetros óptimos de dosificación. Ademais, para aumentar a vida útil das mesturas propostas, estudouse a inclusión de fibras metálicas e de polipropileno. Os resultados obtidos permitiron concluír que o uso de materiais cementantes suplementarios para aumentar a sustentabilidade das mesturas autocompactantes é unha boa opción. Ademais, a inclusión de fibras proporciona beneficios tanto ambientais como económicos sen inconvenientes significativos no comportamento fresco e endurecido dos formigóns., [Resumen] Este trabajo aborda el desarrollo de mezclas autocompactantes con la incorporación de materiales suplementarios procedentes de residuos industriales como sustitutos de cemento para aumentar la sostenibilidad, así como la introducción de fibras para aumentar la vida útil. Estos materiales propuestos son ceniza de biomasa y polvo de granito, que se consideran residuos industriales en la "Eurorregión Galicia-Norte de Portugal" y son abundantes. Dada la creciente presión social hacia la gestión sostenible de los residuos y la eficiencia de los recursos, el uso de estos materiales suplementarios procedentes de residuos industriales ayuda a alcanzar los objetivos de mitigación de CO2 avanzando hacia una economía circular. En este sentido, este estudio se ha desarrollado a nivel de pasta, mortero y hormigón, diseñando diferentes mezclas de base cemento y analizando su comportamiento mediante técnicas de extracción de conocimiento y reología para obtener parámetros óptimos de dosificación. Además, para aumentar la vida útil de las mezclas propuestas, se estudió la inclusión de fibras metálicas y de polipropileno. Los resultados obtenidos permitieron concluir que el uso de materiales cementantes suplementarios para aumentar la sostenibilidad de las mezclas autocompactantes es una buena opción. Además, la inclusión de fibras proporciona beneficios tanto medioambientales como económicos sin inconvenientes significativos en el comportamiento fresco y endurecido de los hormigones., [Abstract] This work addresses the development of self-compacting mixtures with the incorporation of supplementary materials from industrial waste as cement substitutes to increase sustainability, as well as the introduction of fibres to increase the service life of the mixtures. These proposed materials are biomass ash and granite powder, which are abundantly available and considered wastes from the local industry in the “Galicia–North of Portugal Euroregion”. Given the rising social pressure towards sustainable waste management and resource efficiency, the use of supplementary cementitious materials coming from industrial wastes helps to achieve CO2 mitigation goals advancing towards a circular economy. In this regard, this study was developed at the paste, mortar and concrete level, designing different cement-based mixtures and analysing their performance through knowledge extraction techniques and rheology to obtain the optimum dosage parameters. In addition, to increase the service life of the proposed mixtures, the inclusion of metallic and polypropylene fibres was studied. The results obtained led to the conclusion that the use of supplementary cementitious materials to increase the sustainability of self-compacting mixes is a good option. Moreover, the inclusion of fibres provides both environmental and economic gains without significant drawbacks in the fresh and hardened behaviour of the concretes., Este traballo desenvolveuse no marco do proxecto HORREO (Hormigones reciclados autocompactantes robustos: reología en estado fresco y propiedades mecánicas-BIA2014-58063-R) financiado polo Ministerio de Economía e Competitividade que contaba tamén con un contrato predoutoral para a formación de doutores (FPI, BES-2015-071919) que puiden desfrutar durante 4 anos. Para acadar a mención internacional teño que agradecer ao programa de estadías breves da FPI e ao programa IACOBUS pola financiación recibida para realizar dúas estadías de 3 meses na Facultade de Engenheria da Universidade do Porto (FEUP). Ademais, este traballo enmárcase tamén nos seguintes proxectos: Eco3DConcrete (Diseño de hormigón más sostenible para impresión 3D basado en la reología y el control de propiedades a muy cortas edades - PID2020-115433RB-I00), PREHEALING (Diseño de prefabricados de hormigón empleando estrategias sostenibles de auto reparación para incremento de su vida útil - PDC2021-121660-I00) e 3DHealConcrete (Aprovechamiento de sinergias entre las tecnologías de impresión 3D y estrategias de autorreparacion con bacterias para el diseño de hormigones sostenibles y durables -TED2021-129757B-I00) todos eles financiados polo Ministerio de Economía e Competitividade.
RUC. Repositorio da Universidade da Coruña
Publication Artículo científico (JournalArticle)

Automated Control of the Fresh State of Industrial Concrete Behaviour by Rheometer Test Adjustment

  • Rojo-López, Gemma
  • González-Fonteboa, Belén
  • Carro-López, Diego
  • Martínez-Abella, Fernando
[Abstract:] This study aimed to develop a rheometer prototype and define a procedure for adjusting the automated control of the fresh state of concrete. Sixteen batches were produced, and their fresh behaviour was measured at different testing times by applying the Abrams cone and flow curve test (FCT) as the rheological protocol. During this test, the yield stress and plastic viscosity of the concretes were measured in relative units. The rheometer prototype was used to define a new protocol to select the most suitable rheometer impeller arrangement and optimal FCT configuration. This protocol considers the torque at the end of the breakdown period, torque reduction during the breakdown period, segregation, and negative values of the yield stress in relative units. This protocol also enabled an iterative adjustment procedure, facilitating the use of a rheometer for the automated control of the homogeneity and behaviour of fresh concrete, as well as real-time decision making., This research was funded by the Spanish Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación through three research projects entitled: “Design of sustainable concrete for 3D printing based on rheology and on the control of very early properties (Eco3DConcrete)—PID2020-115433RB-I00”, “Design of concrete precast elements incorporating sustainable strategies for self-healing to increase their service life (PREHEALING)—PDC2021-121660-I00” and “Exploiting the synergic effects between 3D printing and self-healing technologies to design sustainable and durable concrete (3DHealConcrete)—TED2021-129757B-I00”.
RUC. Repositorio da Universidade da Coruña
Publication Artículo científico (JournalArticle)

Genetic programming to understand the influence of new sustainable powder materials in the fresh performance of cement pastes

  • Rojo-López, Gemma
  • González-Fonteboa, Belén
  • Pérez Ordóñez, Juan Luis
  • Martínez-Abella, Fernando
[Abstract:] This study focused on pastes that incorporate metakaolin, biomass ash, and granite powder as supplementary cementitious materials to obtain specific expressions to predict rheological properties in pastes and to define the most appropriate dosage parameters using genetic programming. For this purpose, a dataset was developed following a central composite design, and some fresh properties were measured: Marsh cone and rheological properties, such as yield stress and plastic viscosity. The models generated by genetic programming presented robust statistical indices for the properties studied. The influence of supplementary cementitious materials on rheological properties was also analysed through a parametric analysis. After analysing the factors affecting paste rheology, it was concluded that the most important aspects affecting fresh behaviour were water demand and particle interaction, as well as the relation between both effects., This study is part of two projects entitled: “Design of sustainable concrete for 3D printing based on rheology and on the control of very early properties (Eco3DConcrete)- PID2020-115433RB-I00”, “Design of concrete precast elements incorporating sustainable strategies for self-healing to increase their service life (PREHEALING)- PDC2021-121660-I00” and "Exploiting the synergic effects between 3D printing and self-healing technologies to design sustainable and durable concrete (3DHealConcrete) - TED2021-129757B–I00" funded by MINECO.
RUC. Repositorio da Universidade da Coruña
Publication Artículo científico (JournalArticle)

Effect of fly ash blending in internally cured mortar under air-drying curing conditions

  • Rodríguez-Álvaro, Roberto
  • Seara Paz, Sindy
  • Cantero, B.
  • González-Fonteboa, Belén
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, [Abstract]: A proper humid curing of concrete structures is commonly considered as vital to guarantee their strength development and durability. However, undesired periods of air-drying curing conditions can take place. Therefore, the performance of concrete in this situation should be studied. This research work aims to better understand how internally cured fly ash blended cement mortars are affected by air-drying curing conditions. Coal bottom ash (CBA) and wood bottom ash (WA) were used as internal curing water reservoirs. Results show a poor strength development after the age of one week. Moreover, mortar specimens lose a considerable amount of weight during their first days of curing due to water evaporation. This severe drying, together with a long-term carbonation (depth, weight gain and shrinkage), affects the fly ash (FA) blended cement mortars more than the ordinary Portland cement (OPC) mortars. Furthermore, a pore structure analysis was carried out, showing that FA-blended mixtures present a higher total porosity and internal curing cannot effectively refine the pores in the matrix when OPC is the only binder. Self-desiccation was detected in combination with external drying thanks to a comparative study between weight changes and shrinkage. Internal curing can mitigate the self-desiccation shrinkage but increases the drying shrinkage. Moreover, the presence of the waste porous aggregates counteracts the internal curing effect decreasing the strength, and barely affects the carbonation process. As a general conclusion, it can be stated that air-drying curing conditions should be avoided and external wet or sealed curing should always complement internal curing, especially if blended cements are used., This work has been carried out within the framework of the project “Exploiting the synergic effects between 3D printing and self-healing technologies to design sustainable and durable concrete (3DHealConcrete) [TED2021-129757B-I00]” funded by Ministry of Science and Innovation (National Agency of Research – Agencia Estatal de Investigación, Spain). Funding for open access charge: Universidade da Coruña/CISUG.
RUC. Repositorio da Universidade da Coruña
Publication Artículo científico (JournalArticle)

Effects of bacteria-based self-healing nutrients on hydration and rheology of cement pastes

  • Pinto, Adonay
  • González-Fonteboa, Belén
  • Seara Paz, Sindy
  • Martínez-Abella, Fernando
[Abstract:] Crack openings in concrete lead to a reduction in its lifespan. Many authors have analysed different techniques that could repair cracks autonomously, being the use of bacteria one of the most promising approaches. Bacteria are often introduced with nutrients in the concrete mixes, and they may alter the cement hydration. In this study, the effects that calcium lactate, calcium nitrate, and yeast extract have on cement pastes during the early hours of hydration were analysed. To accomplish this, calorimetry, in situ X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Vicat and rheology techniques were employed. The results demonstrated that the addition of calcium lactate led to higher values of ettringite, which altered the rheological behaviour of the pastes. Moreover, when added at 4%, calcium lactate also delayed the setting time by inhibiting the reaction of silicates, a similar effect was observed when yeast extract was added. Lastly, the incorporation of nitrate accelerated the setting time., This work has been carried out within the framework of the following projects: “Design of sustainable concrete for 3D printing based on rheology and on the control of very early properties (Eco3DConcrete)- [PID2020-115433RB-I00]”, “Design of concrete precast elements incorporating sustainable strategies for self-healing to increase their service life (PREHEALING)- [PDC2021-121660-I00]” and “Exploiting the synergic effects between 3D printing and self-healing technologies to design sustainable and durable concrete (3DHealConcrete) [TED2021-129757B-I00]” all funded by MINECO (Ministry of Economy, Industry and Competitiveness). In addition, the authors would like to thank the Xunta de Galicia (Spain) for the financial support through its pre-doctoral contracts program.