Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

TSCH Multiflow Scheduling with QoS Guarantees: A Comparison of SDN with Common Schedulers

  • Orozco-Santos, Federico
  • Sempere Paya, Víctor Miguel|||0000-0001-9271-2010
  • Silvestre-Blanes, Javier|||0000-0001-7091-0040
  • Albero-Albero, Teresa|||0000-0002-5162-6092
[EN] Industrial Wireless Sensor Networks (IWSN) are becoming increasingly popular in production environments due to their ease of deployment, low cost and energy efficiency. However, the complexity and accuracy demanded by these environments requires that IWSN implement quality of service mechanisms that allow them to operate with high determinism. For this reason, the IEEE 802.15.4e standard incorporates the Time Slotted Channel Hopping (TSCH) protocol which reduces interference and increases the reliability of transmissions. This standard does not specify how time resources are allocated in TSCH scheduling, leading to multiple scheduling solutions. Schedulers can be classified as autonomous, distributed and centralised. The first two have prevailed over the centralised ones because they do not require high signalling, along with the advantages of ease of deployment and high performance. However, the increased QoS requirements and the diversity of traffic flows that circulate through the network in today's Industry 4.0 environment require strict, dynamic control to guarantee parameters such as delay, packet loss and deadline, independently for each flow. That cannot always be achieved with distributed or autonomous schedulers. For this reason, it is necessary to use centralised protocols with a disruptive approach, such as Software Defined Networks (SDN). In these, not only is the control of the MAC layer centralised, but all the decisions of the nodes that make up the network are configured by the controller based on a global vision of the topology and resources, which allows optimal decisions to be made. In this work, a comparative analysis is made through simulation and a testbed of the different schedulers to demonstrate the benefits of a fully centralized approach such as SDN. The results obtained show that with SDN it is possible to simplify the management of multiple flows, without the problems of centralised schedulers. SDN maintains the Packet Delivery Ratio (PDR) levels of other distributed solutions, but in addition, it achieves greater determinism with bounded end-to-end delays and Deadline Satisfaction Ratio (DSR) at the cost of increased power consumption., This work has been supported by DAIS (https://dais-project.eu/) which has received funding from the ECSEL Joint Undertaking (JU) under grant agreement No 101007273. The JU receives support from the European Union's Horizon 2020 research and innovation programme and Sweden, Spain, Portugal, Belgium, Germany, Slovenia, Czech Republic, Netherlands, Denmark, Norway and Turkey. It has also been funded by Generalitat Valenciana through the "Instituto Valenciano de Competitividad Empresarial-IVACE". Furthermore, has been supported by the MCyU (Spanish Ministry of Science and Universities) under the project ATLAS (PGC2018-094151-B-I00), which is partially funded by AEI, FEDER and EU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Scalability Enhancement on Software Defined Industrial Wireless Sensor Networks Over TSCH

  • Orozco-Santos, Federico
  • Vera-Pérez, Jose
  • Sempere Paya, Víctor Miguel|||0000-0001-9271-2010
  • Silvestre-Blanes, Javier|||0000-0001-7091-0040
[EN] Industry 4.0 digitization requirements have led to widespread adoption of industrial wireless sensor networks (IWSNs) in manufacturing environments. These require strict control of the traffic flowing over the network to ensure the quality of service. Software-defined networks (SDNs) can address this challenge, as their centralized operation allows routing and media access control (MAC) protocols to be optimized. In addition, in many cases a massive deployment of metering devices is necessary, therefore the network must be scalable, to allow an increase in the number and density of nodes in the network. This implies an increase in the control traffic required by SDNs, generating a significant reduction in the throughput available for data. This is because the length of the timeslot limits the throughput of the network in protocols that uses time division, such as the Time Slotted Channel Hopping (TSCH), conditioning the number of nodes that the network can have and its data sending rate. In this paper, we propose to exploit the integration and reconfiguration capabilities of SDN to extend the number of nodes in the network through the use of multi-radio sinks called virtual sinks, orchestrated from the SDN controller, and extending their use to multiple SD-IWSNs to take full advantage of the radio spectrum. To optimize bandwidth usage, the SDN controller will allocate network slices, allowing nodes to send data with a high frequency using dedicated channels. The results obtained show that the use of multi-radio sinks provides for increasing the maximum number of nodes that can be deployed while preserving the quality of service (QoS) requirements. A linear increase in nodes at least 0.7 times for each radio interface is obtained compared to an SD-IWSN with a traditional sink. In addition, the use of virtual sinks increases the packet frequency of the network by a factor equal to the number of radio interfaces. Moreover, the total number of nodes is improved through the coexistence of multiple SD-IWSNs, where up to 13.7 times more nodes can be scheduled using all the available spectrum orchestrated from the same SDN controller., This work was supported in part by DAIS (https://dais-project.eu/) through the ECSEL Joint Undertaking (JU) under Grant 101007273; in part by JU through the European Union's Horizon 2020 Research and Innovation Programme and Sweden, Spain, Portugal, Belgium, Germany, Slovenia, Czech Republic, The Netherlands, Denmark, Norway, and Turkey; and in part by the Generalitat Valenciana through the Instituto Valenciano de Competitividad Empresarial~IVACE.
UCrea Repositorio Abierto de la Universidad de Cantabria
Publicación Artículo científico (JournalArticle)

Accelerating the verification of forward error correction decoders by PCIe FPGA cards

  • Suárez Plata, Daniel Nicolás
  • Fernández Solórzano, Víctor Manuel|||0000-0003-0614-151X
  • Posadas Cobo, Héctor
  • Sánchez Espeso, Pablo Pedro
Presilicon forward error correction (FEC) decoding hardware is typically designed using hardware description languages (HDLs). Its verification is a hard task due to its intrinsic tendency to correct errors. The generation and injection of millions of random inputs as well as the cross-checking of the corresponding outputs are highly recommended. Using HDL simulations for such work leads to prohibitive execution times. This letter proposes a verification strategy in which the software testbed is executed on a multicore host and the hardware under verification is prototyped on a PCIe accelerator card. Data are transferred in big blocks of codewords over a high-bandwidth PCIe channel and applied to the decoder using a pipeline management to maximize the use of computational resources and minimize the verification time. The decoder is replicated with parallel access to DDRs. OpenMP is used to leverage the parallel capabilities of the host and OpenCL, together with Xilinx Runtime (XRT) Library, to manage the PCIe FPGA card execution. The results show an important speed-up with respect to HDL simulation and to other prototyping approaches., This work has been supported by Project PID2020-116417RB-C43, funded by Spanish MCIN/AEI/10.13039/501100011033 and by Project No 101007273 ECSEL DAIS, funded by EU H2020 and by Spanish pci2021-121988.