Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

TECNALIA Publications
Publicación Artículo científico (JournalArticle)

Surface chemistry and bioactivity of colloidal particles from industrial kraft lignins

  • Gordobil, Oihana
  • Li, Huisi
  • Izquierdo, Ana Ayerdi
  • Egizabal, Ainhoa
  • Sevastyanova, Olena
  • Sandak, Anna
The morphology control of lignin through particle size reduction to nanoscale seems to be a suitable conversion technology to overcome the intrinsic limitations of its native form to develop a wide range of biomaterials with high performance. Colloidal lignin particles (CLPs) in the range of 150–200 nm were synthesised from hardwood and softwood kraft lignins by the solvent shifting method. The initial molecular features of kraft lignins were evaluated in terms of purity, molecular weight distribution, and chemical functionalities. The impact of the lignin source and structure on the morphology, size distribution, and surface chemistry of CLPs was evaluated by particle size analyser, SEM, TEM and 1H NMR. The results evidenced the influence of the botanical origin on the morphology and surface chemistry of particles. Furthermore, the antioxidant properties and cytotoxicity of lignins and corresponding CLPs, towards lung fibroblast cells were compared. CLPs from hardwood kraft lignins exhibited higher antioxidant power against DPPH free radical and a higher cytotoxic effect (IC30 = 67–70 μg/mL) against lung fibroblast when compared to CLPs from softwood kraft lignin (IC30 = ~91 μg/mL). However, the cytotoxicity of these biomaterials was dose-dependent, suggesting their potential application as active ingredients in cosmetic and pharmaceutic products at low concentrations.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Thermally modified (TM) beech wood: compression properties, fracture toughness and cohesive law in mode II obtained from the three-point end-notched flexure (3ENF) test

  • Sebera, Václav
  • Brabec, Martin
  • Decky, David
  • Cermak, Petr
  • Tippner, Jan
  • Milch, Jaromír
  • Redón-Santafé, Miguel|||0000-0002-4581-1590
[EN] The fracture properties of thermally modified beech (Fagus sylvatica) wood (TMW) at 180 degrees and 200 degrees C were evaluated in mode II using the three-point end-notched flexure (3ENF) scheme assisted by three-dimensional (3D) stereovision equipment for obtaining displacements and strains. The compliance-based beam method (CBBM) provided the strain energy release rates (G(II)) of TMW and cohesive laws for both native wood (W) and TMW. Based on the CBBM and equivalent crack length approach (ECLA), G(II) was obtained directly from the force-deflection data. The thermal modification (TM) process reduced the compressive strength by 4.4% and increased the compressive elastic modulus by 38.3%, whereas G(II) was reduced substantially by 40.8% and 67.9% at TM180 degrees C and TM200 degrees C, respectively. TM also increased wood brittleness that was visible on the displacement slip reduction. The resulting mean cohesive models can be used for numerical analyses. The fracture properties of TMW have to be taken into consideration for constructional wood application, when cyclic loading may lead to microcracking and material fatigue., The authors would like to thank COST Action FP1407 (Funder Id: https://dx.doi.org/10.13039/501100000921), the European Commission for funding the InnoRenew CoE project under the Horizon2020 Widespread-Teaming program (grant agreement #739574), the Republic of Slovenia for providing support from the European Regional Development Funds, and the financial support provided by the Internal Grant Agency (IGA) of the Faculty of Forestry and Wood Technology, Mendel University in Brno (LDF_PSV_2016015).
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

Simultaneous Improvement of Surface Wettability and UV Resistance of Wood with Lignin-Based Treatments

  • Herrera Díaz, René
  • Poohphajai, Faksawat
  • Sandak, Anna
  • Gordobil Goñi, Oihana
Recent advancements in wood modification aim to enhance the inherent qualities of this versatile biological material, which includes renewability, ease of processing, and thermal insulation. This study focuses on evaluating the effectiveness of lignin as a protective agent for less durable wood species, namely, Pinus nigra and Fagus sylvatica L. The impregnation of wood with three various forms of lignin, such as kraft lignin, acetylated kraft lignin, and lignin nanoparticles, was carried out using the vacuum technique at room conditions. The results showed that the treatments significantly improve the hydrophobicity of wood surfaces, particularly in pine wood, and provide protection against UV ageing. Additionally, the treatments contributed to the stabilisation of moisture content at different humidity levels. Although slight colour variations were observed, their impact on the visual appearance was minimal, and the thermal analysis confirmed enhanced thermal properties. Additionally, plasma treatment further enhanced hydrophobicity after treatments, offering potential benefits in terms of moisture resistance and durability. The findings of this study highlight the promising effects of lignin-based treatments on wood properties, providing sustainable solutions for wood protection in various sectors. However, further optimisation is needed to fully explore the potential of lignin and lignin nanoparticles., R. Herrera thanks the (IJC2020-043740-I) grant funded by MCIN/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR, and University of the Basque Country UPV/EHU (JDCI20/14) for the mobility grant. O. Gordobil acknowledges the financial support from the Spanish research agency (aei) (ryc-2021-031328-i) funded by mcin/aei/ 10.13039/501100011033 by European Union NextGenerationEU/prtr.4. Financial support from the Basque Government in the frame of Grupos Consolidados (IT-1498-22) and (IT-1690-22) is acknowledged. This research was funded by the European commission’s funding of the Innorenew project (grant agreement #739574 under the horizon 2020 widespread-2-teaming program) and the republic of Slovenia (investment funding from the republic of Slovenia and the European regional development fund). Co-funded by the European Union (ERC, ARCHI-SKIN, #101044468). Views and opinions expressed are, however, those of the author(s) only and do not necessarily reflect those of the European Union or the European Research Council. Neither the European Union nor the granting authority can be held responsible for them. This research presents a preliminary study related to MULTI-WOOD project #101067636 funded by Horizon Europe MSCA PF.
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

One-Step Lignin Refining Process: The Influence of the Solvent Nature on the Properties and Quality of Fractions

  • Gordobil Goñi, Oihana
  • Díaz Herrera, René
  • Sandak, Jakub
  • Sandak, Anna
Heterogeneity of kraft lignin is one of the main limitations for the development of high-performance applications. Therefore, refining lignin using organic solvents is a promising strategy to obtain homogenous fractions with controlled quality in terms of structure and properties. In this work, one-step refining processes for hardwood kraft lignin using nine organic solvents of different chemical nature and polarity were carried out with the aim of investigating and understanding the effect of the type of organic solvent on the quality of resulting fractions. Structural features of both soluble and insoluble lignin fractions were assessed by GPC, Py-GC-MS, and FTIR linked to PCA analysis. Moreover, functional properties such as physical appearance, hygroscopicity, antioxidant capacity, and thermal properties were evaluated. The results evidenced the relationship between the nature and polarity of the solvents and the properties of the obtained soluble and insoluble fractions., This research was funded by the European Commission’s funding of the InnoRenew project (Grant Agreement #739574 under the Horizon 2020 WIDESPREAD-2-Teaming program) and the Republic of Slovenia (investment funding from the Republic of Slovenia and the European Regional Development Fund). O.G. is grateful for the financial support received from the European Union’s Horizon 2020 research and innovation program under the Marie Skłodowska-Curie Action for development of the BIO4CARE project (Grant Number #101023389). R.H. received funding from the Spanish Ministry of Science and Innovation and the University of the Basque Country UPV/EHU (POSTDOC: IJC2020-043740-I).
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

Weathering of Wood Modified with Acetic Anhydride—Physical, Chemical, and Aesthetical Evaluation

  • Sandak, Anna
  • Gordobil Goñi, Oihana
  • Poohphajai, Faksawat
  • Herrera Díaz, René
The goal of this study is to comprehensively evaluate the natural weathering performance of three wood species representing hardwood and softwood modified with the acetylation process. Alder (Alnus glutinosa L.), beech (Fagus sylvatica L.), and radiata pine (Pinus radiata D. Don) were characterised by various techniques to determine the aesthetical, chemical, and physical changes. The overall aesthetic performance of the investigated species was similar, with all showing a change in appearance after 9 months of exposure. However, the multi-sensor approach used for characterisation revealed differences in weathering behaviour related to surface erosion, wettability, and changes in chemical composition between the investigated species. An increase in the surface roughness observed for both hardwoods was associated with the erosion of the wood surface and the leaching of photodegraded chemical components. On the contrary, values of Sa remained relatively constant for acetylated radiata pine. Acetylated pine wood exhibited lower susceptibility to bleaching at the initial stage of the weathering process (3 months) and represented a more constant CIE L* compared to the investigated hardwood species. The contact angle measured with water gradually decreased in the case of acetylated radiata pine for up to six months, then it plateaued with a slight oscillation around 15°. For both hardwood species, the big drop was observed already after three months, followed by rather similar values. The PCA of IR spectra highlighted different mechanisms in the weathering of acetylated softwood and hardwood. The acetylated hardwood samples showed higher thermal stability than acetylated radiata pine. Experimental findings provide a comprehensive understanding of the long-term performance of acetylated wood, which directly influences its practical applications by enhancing design strategies, maintenance planning, product development, market acceptance, and overall sustainability. Performed tests have demonstrated the potential of underutilised hardwood species, enhanced through the acetylation process, to serve as alternative cladding materials to commonly used acetylated radiata pine., This study was funded by the European Commission’s funding of the InnoRenew project (#739574 under the Horizon 2020 Widespread-2-teaming program), the Republic of Slovenia (investment funding from the Republic of Slovenia and the European regional development fund), and infrastructural ARRS program IO-0035. This work presents a study related to WoodLCC (#773324), which is supported under the umbrella of ERA-NET Cofund ForestValue by the Ministry of Education, Science, and Sport (MIZS)—Slovenia and MULTI-WOOD project #101067636 funded by Horizon Europe MSCA PF. O. Gordobil acknowledges grant RYC-2021-031328-I, funded by MICIU/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR, and financial support from the Basque Country government in the frame of consolidated groups (IT-1690-22). It is co-funded by the European Union (ERC, ARCHI-SKIN, #101044468). Views and opinions expressed are, however, as those of the author(s) only and do not necessarily reflect those of the European Union or the European Research Council. Neither the European Union nor the granting authority can be held responsible for them.
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

Fractionation of lignin using organic solvents: A combined experimental and theoretical study

  • Ponnuchamy, Veerapandian
  • Gordobil Goñi, Oihana
  • Herrera Díaz, René
  • Sandak, Anna
  • Sandak, Jakub
Refining of industrial lignin to produce homogeneous fractions is essential for high-value applications. However, the understanding of key interactions between a variety of solvents with lignin polymer is still uncertain. In this work, single-step fractionation of industrial hardwood kraft lignin (HKL) using organic solvents of different polarities - ethanol, acetone, diethyl ether and hexane - was investigated by combining an experimental and theoretical approach. Experimental results revealed that higher polarity solvents (ethanol and acetone) exhibited higher solubility yield compared to moderate and low polarity solvents. The chemical differences between lignin fractions were proven by pyrolysis gas chromatography mass spectrometry and near infrared spectroscopy. Density functional theory (DFT) results indicated that ethanol presented higher interaction energy followed by acetone, diethyl ether and hexane, which was consistent with experimental findings. Hydrogen bond and non-covalent interaction results from DFT demonstrated that the predominant interaction was found for high polarity of ethanol over other solvents and gamma-OH in the lignin model is the key site., The authors gratefully acknowledge the European Commission for funding the InnoRenew project [Grant Agreement #739574] under the Horizon2020 Widespread-Teaming program, the Republic of Slovenia (investment funding from the Republic of Slovenia and the European Union European Regional Development Funds) and infrastructural ARRS program IO-0035. Additionally, O.G. is grateful for the financial support received from the University of the Basque Country (post-doctoral grant DOCREC18/29) and R.H. acknowledges to the Department of Education of the Basque Government (post-doctoral grant INGVTCL4-D00112-7).
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

Hydrophobization and Photo-Stabilization of Radiata Pinewood: The Effect of the Esterification on Thermal and Mechanical Properties

  • Herrera Díaz, René
  • Gordobil Goñi, Oihana
  • De Hoyos Martínez, Pedro Luis
  • Sandak, Anna
  • Labidi Bouchrika, Jalel
Wood protection through chemical modification has received increasing interest over the last decades due to the environmental issues related to conventional biocides or protecting products. Consequently, a wide range of new treatments are developed in laboratories, which are later scaled up in the industrial environment. The main goal of modifying wood for indoor–outdoor application is to change its hydrophilic character, which in turn improves the intrinsic properties of the material and its durability against external factors. Wood can be esterified through its hydroxyl groups to obtain a hydrophobic and photo-stable material. Chemical modifications of Pinus radiata D. Don wood using hexanoyl chloride (P6), dodecanoyl chloride (P12), and stearoyl chloride (P18) were carried out at different concentrations. Esterification was confirmed by Fourier Transform Infrared Spectroscopy (FTIR) technique combined with a discriminatory analysis. Weight percent gain was associated with the number of carbons of the aliphatic chain of the fatty acid (P6 > P12 > P18). Moreover, an increase of wood density as a consequence of modification treatments was observed. A substantial improvement of the hydrophobicity of wood was observed by dynamic contact angle measurements. In addition, the effect of ultraviolet (UV) radiation on color changes was reduced with the treatments. Furthermore, the P6 treatment presented acceptable values of modulus of elasticity (MOE) and modulus of rupture (MOR), being suitable for similar mechanical uses as non-treated pinewood. However, only treatments P12 and P18 enhanced thermal resistance of the pinewood in an oxidative atmosphere., This research was funded by the Basque Government, grant number IT1008-16 and the APC was funded by the Basque Government, grant number IT1008-16. The author gratefully acknowledges the European Commission for funding the InnoRenew project [Grant Agreement # 739574] under the Horizon2020 Widespread-Teaming program, the Republic of Slovenia (investment funding of the Republic of Slovenia and the European Union European Regional Development Fund) and infrastructural ARRS program IO-0035. Part of this work was conducted during the project Multi-spec (BI-IT/18-20-007) funded by ARRS. RH is grateful to the Department of Education of the Basque Government (post-doc INGVTCL4-D00112-7) and the University of the Basque Country UPV/EHU.
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

Characterization of the Compounds Released in the Gaseous Waste Stream during the Slow Pyrolysis of Hemp (Cannabis sativa L.)

  • Marrot, Laetitia
  • Meile, Kristine
  • Zouari, Mariem
  • DeVallance, David
  • Sandak, Anna
  • Herrera Díaz, René
This study aims to characterize and valorize hemp residual biomass by a slow pyrolysis process. The volatile by-products of hemp carbonization were characterized by several methods (TGA, UV-VIS, TLC, Flash Prep-LC, UHPLC, QTOF-MS) to understand the pyrolysis reaction mechanisms and to identify the chemical products produced during the process. The obtained carbon yield was 29%, generating a gaseous stream composed of phenols and furans which was collected in four temperature ranges (F1 at 20–150 °C, F2 at 150–250 °C, F3 at 250–400 °C and F4 at 400–1000 °C). The obtained liquid fractions were separated into subfractions by flash chromatography. The total phenolic content (TPC) varied depending on the fraction but did not correlate with an increase in temperature or with a decrease in pH value. Compounds present in fractions F1, F3 and F4, being mainly phenolic molecules such as guaiacyl or syringyl derivatives issued from the lignin degradation, exhibit antioxidant capacity. The temperature of the pyrolysis process was positively correlated with detectable phenolic content, which can be explained by the decomposition order of the hemp chemical constituents. A detailed understanding of the chemical composition of pyrolysis products of hemp residuals allows for an assessment of their potential valorization routes and the future economic potential of underutilized biomass., This research was funded by the European Commission for funding the InnoRenew project (Grant agreement #739574 under the Horizon 2020 WIDESPREAD-2-Teaming program) and the Republic of Slovenia (investment funding from the Republic of Slovenia and the European Regional Development Fund), the European Union’s Horizon 2020 research and innovation programme under the H2020 Marie Skłodowska-Curie Actions (Grant Number 898179). Kristine Meile received funding from the ERDF Project No. 1.1.1.2/VIAA/3/19/388 “A biorefinery approach to the separation and application of the products of lignocellulose pyrolysis”. Rene Herrera received funding from Spanish Ministry of Science and Innovation and the University of the Basque Country UPV/EHU (POSTDOC: IJC2020-043740-I).