Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

Biblos-e Archivo. Repositorio Institucional de la UAM
Publicación Artículo científico (JournalArticle)

Folded W-band waveguide filters with resonant coupling apertures for the generation of additional transmission zeros

  • Miek, Daniel
  • Höft, Michael
  • Morán López, Ana
  • Ruiz Cruz, Jorge Alfonso
Título del postprint: Realization of folded W-band waveguide filters with multiple resonant transmission zeros, In this paper the realization of multiple additional transmission zeros in folded W-band waveguide filters is discussed. The transmission zeros (TZs) can be placed symmetrically as well as asymmetrically in the near passband region of the filter and arise due to a resonant coupling between source and / or load. Third and fourth order filter set-ups are presented, showing in total between three and six TZs. These zeros can be used to improve the selectivity of the filter without increasing the overall order. The filter design and realization process is discussed. Subsequently, the measurement results are compared with simulation, showing good agreement. As the filters are designed for the W-band, the manufacturing process is connected with some difficulties which are addressed within this paper as well, This project has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 811232. This work was partially supported by the Spanish Government under Grant TEC2016-76070-C3-1-R (AEI/FEDER, UE)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Using Dielectric Rods to Reconfigure Combline Filters in Center Frequency and Bandwidth

  • Sharma, Abhishek
  • Guglielmi, Marco
  • Cogollos, Santiago|||0000-0002-4189-2952
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This article describes the use of dielectric rods to reconfigure combline filters both with respect to center frequency and bandwidth. In this context, a new filter topology is developed in order to maximize the achievable reconfiguration range. The design of a prototype is discussed in detail, clearly demonstrating the feasibility of center frequency and bandwidth reconfiguration, with the same filter structure, while maintaining an equiripple return loss. In addition to theory, a combline filter prototype is also fabricated, tuned and measured in several configurations showing excellent agreement with simulations, thereby fully validating both the basic concept and the design procedure, This work was supported in part by the European Union's Horizon 2020 Research and Innovation Program through the Marie Sklodowska-Curie Innovative Training Networks (ITN) (TESLA) under Grant 811232; and in part by the Minsiterio de Ciencia e Innovacion (MICIN), Spanish Government, through the Research and Development Project under Grant PID2019-103982RB-C41 (funded by MICIN/AEI/10.13039/501100011033).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Remote Reconfiguration of Microwave Filters Using Dielectric Tuners

  • Sharma, Abhishek
  • Ossorio, Javier
  • Smacchia, Davide
  • Tronser, Tillman
  • Guglielmi, Marco
  • Cogollos, Santiago|||0000-0002-4189-2952
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] The objective of this article is to explore the use of dielectrics to reconfigure remotely microwave filters in rectangular waveguide. To start, we study experimentally the phase shift that is achievable using dielectric tuning elements in a rectangular waveguide. We then compare the results obtained with the performance of standard metallic tuning cylinders and screws. Next, the passive intermodulation (PIM) behavior of dielectric tuning elements is investigated experimentally. The PIM results obtained using dielectrics are then compared with the ones of metallic tuning elements. After that, the measured results for a filter tuned with a number of different dielectric tuning elements are discussed to identify the required relation between cavity size, dielectric constant, and tuner diameter. As a proof of concept, we then design, manufacture, and test two filters, one in WR75 and the other in WR90. Both simulated and measured results are then presented clearly demonstrating that the structures discussed can indeed be reconfigured (or tuned) both in terms of filter center frequency and bandwidth. Finally, computer-driven linear actuators are connected to the dielectric tuners, and the remote tuning capability is successfully demonstrated., This work was supported in part by the European Union's Horizon 2020 Research and Innovation Program, through the Marie Sklodowska-Curie ITN (TESLA) under Grant 811232 and in part by the Minsiterio de Ciencia e Innovacion (MICIN, Spanish Government) through the Research and Development Project under Grant PID2019-103982RB-C41 (funded by MICIN/AEI/10.13039/501100011033).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Compact Substrate Integrated Waveguide Wideband Bandpass Filter With Post-Manufacturing Tuning Capabilities

  • Messaoudi, El Mehdi
  • Martínez Pérez, Jorge Daniel|||0000-0002-7119-3714
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] In this paper, a miniaturized wideband bandpass filter in coaxial substrate integrated waveguide (SIW) technology is presented. To improve the response selectivity and coupling control, a multi-layer structure has been implemented, introducing both strong magnetic and electric couplings. To reduce the physical size of the device, surfaced-mounted device (SMD) capacitors have been integrated on the top layer. These allow both resonant frequency and capacitive coupling level control. Thus, a 4-th order Chebyshev filter with an absolute bandwidth (BW) of 2.9 GHz centered at 5.35 GHz has been designed, fabricated and measured. An extremely small filter size of 7 x 7 mm(2) has been obtained. A study of manufacturing tolerances are also presented in this paper, together with a post-manufacturing response correction allowed by the SMD elements. As it is shown in the paper, the filter's out-of-band rejection can be easily enhanced by introducing additional transmission zeros (TZs)., This work was supported in part by the European's Union Horizon 2020 Research and Innovation Programme under the MarieSklodowska-Curie Innovative Triangle Networks (ITN) through TESLA under Grant 811232, in part by the European Space Agency(ESA) under Contract 4000124983, in part by the Ministerio de Ciencia e Innovacion (MICIN) through Spanish Government under the Research and Development Project PID2019-103982R-C41 and Project MICIN/AEI/10.13039/501100011033, and in part by the funding for open access charge: Universitat Politecnica de Valencia
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Integrating multiple stubs in stepped-impedance filter aiming for high selectivity

  • Sami, Abdul
  • Gómez Laso, Miguel Ángel
  • Lopetegui Beregaña, José María
  • Arnedo Gil, Israel
  • Calero Fernández, Ibai
  • Teberio Berdún, Fernando
  • Martín Iglesias, Petronilo
  • Benito Pertusa, David
  • Arregui Padilla, Iván
A design technique to include multiple and fully-controlled transmission zeros (TZs) in the frequency response of rectangular waveguide commensurate-line stepped-impedance filters is presented in this letter. These bandpass filters (BPFs) are known for having reduced sensitivities against manufacturing inaccuracies and are composed of multiple waveguide sections. In order to improve their selectivity, 3λg/4 and λg/4-stubs are included to create multiple TZs around the passband. The proposed technique allows us to add multiple stubs in a single section and, therefore, only minor adjustments in the affected part of the filter are required, which simplifies the overall design process. The technique has been verified with a design example with four TZs (two on each side) near the passband., This work was supported by the Spanish Ministerio de Ciencia e Innovación –Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) under Project PID2020-112545RB-C53 and by the European Union’s Horizon 2020 Research and Innovation Program under Grant 811232-TESLA-H2020-MSCA-ITN-2018.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Synthesis of rectangular waveguide filters with smooth profile oriented to direct metal additive manufacturing

  • Percaz Ciriza, Jon Mikel
  • Hussain, Jabir
  • Arregui Padilla, Iván
  • Teberio Berdún, Fernando
  • Benito Pertusa, David
  • Martín Iglesias, Petronilo
  • Arnedo Gil, Israel
  • Gómez Laso, Miguel Ángel
  • Lopetegui Beregaña, José María
In this paper, a novel design method for rectangular waveguide filters intended for fabrication using direct metal additive manufacturing is proposed. The synthesized filters will feature a smooth profile that allows us to fabricate them orienting the filter propagation axis in the vertical building direction, achieving an optimum configuration for direct metal additive manufacturing fabrication. The novel design method is valid for any all-pole transfer function, which is initially implemented with a commensurate-line distributed unit element prototype. The impulse response of that initial prototype is then properly interpolated to obtain the target response for a smooth-profiled filter with similar length and profile excursion. Finally, the target impulse response just generated is implemented in rectangular waveguide technology employing a novel inverse scattering synthesis technique that relies on the coupled-mode theory to model the electromagnetic behavior of the waveguide filter. The novel inverse scattering synthesis technique is general and also valid for the case of filters with very high rejection levels, which is of great relevance in rectangular waveguide technology. A Ku-band low-pass filter with stringent satellite specifications is designed using the proposed method, fabricated by means of a direct metal additive manufacturing technique, and measured with a vector network analyzer. A very good agreement is achieved between the simulated and measured results, fulfilling the required specifications and demonstrating the feasibility and performance of the novel design method., This work was supported in part by the Spanish Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (MCIN/AEI/10.13039/ 501100011033) under Project TEC2017-85529-C3-2-R (co-funded by the Fondo Europeo de Desarrollo Regional (FEDER) “A way to make Europe”) and Project PID2020-112545RB-C53, and in part by the Advanced Technologies for future European Satellite Applications (TESLA) Project (European Union’s Horizon 2020 Research and Innovation Programme through the Marie Sklodowska-Curie Grant) under Grant 811232.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Robust tolerance design of bandpass filter with improved frequency response for Q-band satellite applications

  • Sami, Abdul
  • Teberio Berdún, Fernando
  • Miranda Santafé, Luis
  • Arnedo Gil, Israel
  • Martín Iglesias, Petronilo
  • Benito Pertusa, David
  • Lopetegui Beregaña, José María
  • Gómez Laso, Miguel Ángel
  • Arregui Padilla, Iván
A rectangular waveguide bandpass filter for Q-band with simple fabrication is proposed in this letter. The design is based on the use of the first passband replica of commensurate-line stepped-impedance structures and achieves the suppression of their inherent low-pass response. In order to do it, the filter is implemented by rectangular waveguide sections with different widths and heights that can be analytically calculated. The technique is validated by a 9th order Chebyshev filter with passband between 40 and 43 GHz and fabrication yield equal to 84 % for a manufacturing error of ± 20 μm. The measured results of the prototype fabricated with CNC milling are in good agreement with the simulated ones., This work was supported by the Spanish Ministerio de Ciencia, Innovación y Universidades–Agencia Estatal de Investigación under Project TEC2017-85529-C3-2-R (AEI, FEDER-EU) and by the European Union’s Horizon 2020 research and innovation programme under grant agreement no. 811232-TESLA-H2020-MSCA-ITN-2018.