Pasar al contenido principal

BASES PARA EL DISEÑO DE ESTRUCTURAS SOSTENIBLES DE HORMIGON DE MUY ALTO RENDIMIENTO A NIVEL PRENORMATIVO

BIA2016-78460-C3-1-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Flexural and compressive creep behavior of UHPFRC specimens

  • Llano-Torre, Aitor
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] The long term behavior of Ultra High Performance Fiber Reinforced Concrete (UHPFRC) is analyzed in this study. The experimental campaign covered creep in compression and creep in flexure in cracked state. Three types of specimens were cast: cylindrical specimens (empty set100 x 200 mm) for compressive creep and shrinkage, and prismatic specimens type regular "R" (150 x 150 x 600 mm) and type slim "S" (150 x 40 x 600 mm) for flexural creep in cracked state. Specimens R were notched up to 50 mm in depth to weak the central section and then pre-cracked until 0.65 mm of Crack Mouth Opening Displacement (CMOD). Specimens S were pre-cracked unnotched until a loss of 50% of stiffness was observed. Flexural creep tests were performed during 270 days under load, and until 360 days the compressive tests. Measurements from three experimental sources were obtained: CMOD, compressive strains on top of prismatic specimens and longitudinal compressive strains in cylindrical specimens. Creep coefficients and parameters related with deferred deformations velocity were obtained from all three sources. Creep coefficients under flexure at 270 days ranged from 0.62 to 1.20 in the tensile zone, and from 0.72 to 0.90 in the compressive zone. Creep coefficient in compression at one year was 1.07, which is consistent with values found in the literature. Deferred deformations velocities at early ages were greater in specimens R than in specimens S, and a secondary creep stage was achieved in all specimens after 210 days of sustained loading., The authors wish to thank the technicians of ICITECH, where the experimental work was developed. The financial support of the project BIA2016-78460-C3-1-R "Bases para el diseno de estructuras sostenibles de hormigon de muy alto rendimiento a nivel prenormativo/Diseno eficiente de estructuras de HMAR", supported by the Ministry of Economy and Competitiveness (Spain) and the European Regional Development Fund (European Union), is also gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Comparison of macrosynthetic and steel FRC shear-critical beams with similar residual flexure tensile strengths

  • Ortiz-Navas, Francisco
  • Leiva, Gabriel
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] This study extends previous experimental research on the shear behaviour of macrosynthetic fibre-reinforced concrete beams and compares them to steel fibre-reinforced concrete beams with similar mechanical and geometrical properties. This work employed two fibre types: 60/0.9 (long/diameter) double hooked-end steel fibre and 60/85 monofilament polypropylene fibre. Beams were tested by shear loading covering parameters, such as two different cross-section widths, two shear-span-to-effective-depth ratios, two fibre types and using repetitions with and without transverse reinforcement. For quantitative comparison purposes, crack pattern evolution was studied along increasing loads levels. Effects were studied by photogrammetry, including influence of fibres on crack propagation in uncracked and dowel zones, influence of fibres on stirrup behaviour, and shear deformation or kinematics of critical shear cracks. The results evidenced similar effectiveness for both fibre types in controlling shear crack propagation and horizontal dowel cracking. Both fibres provided similar shear ductility and shear deflections. Consequently, the authors confirm that residual flexural tensile strengths are a convenient parameter for characterising the shear behaviour of fibre-reinforced concrete beams., This work forms part of Project "BIA2016-78460-C3-1-R" supported by the State Research Agency of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Tensile behaviour of reinforced UHPFRC elements under serviceability conditions

  • Khorami, M.
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] Tension stiffening is an essential effect that influences the behaviour of concrete structures under serviceability conditions, mainly regarding crack control and deflection behaviour. Serviceability conditions can be studied experimentally by running the so-called uniaxial tensile test. This paper reports an extensive experimental research conducted to study the tensile behaviour of reinforced Ultra-High Performance Fibre-Reinforced Concrete (R-UHPFRC) under service conditions by uniaxial tensile testing. The parameters studied were the reinforcement ratio and the steel fibre content in a experimental programme including 36 specimens. Special testing equipment and methodology to measure the post-cracking deformation of R-UHPFRC ties were developed, and special attention was paid to the shrinkage effect. The tensile elements' axial stiffness was approximately parallel to the bare bar response after microcracking formation showing a full tension-stiffening response. The average tensile capacity of the reinforced elements (tension stiffening response) was achieved. Concrete's contribution in the R-UHPFRC ties with the tensile properties deriving from four-point bending tests (4PBTs) on non-reinforced UHPFRC specimens was also compared. The experimental results revealed a slight increase in concrete's contribution with the higher reinforcement ratio. Moreover, the concrete's contribution in the tensile elements was higher than the characteristic tensile properties deriving from 4PBTs., This study forms part of Project BIA2016-78460-C3-1-R, supported by the Ministry of Economy and Competitiveness of Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effects of tension stiffening and shrinkage on the flexural behavior of reinforced UHPFRC beams

  • Mezquida-Alcaraz, Eduardo J.
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] This paper presents a study on the flexural behavior of Ultra-High-Performance Fiber-Reinforced Concrete (UHPFRC) beams, which included conventional reinforcing bars. The study focuses on critical design aspects, such as concrete shrinkage and cracking implications on the tension-stiffening phenomenon. An experimental program with two different sized flexural reinforced UHPFRC beams was run. Beams were cast and tested in a four-point bending test (4PBT) using UHPFRC with different amounts of fibers: 130 and 160 kg/m(3) (1.66% and 2.00% in vol.) to cover a wide range of strain-softening and strain-hardening constitutive UHPFRC behaviors. A nonlinear finite element model (NLFEM) was developed to validate the mechanical tensile characterization of UHPFRC when applied to reinforced elements. Both shrinkage and tension-stiffening effects were considered to improve the model. After the NLFEM simulation, very reliable results were obtained at both the service and ultimate load levels compared to the experimental ones. Finally, some aspects about the design of reinforced UHPFRC cross-sections under bending forces are addressed and satisfactorily compared to the experimental results., This work forms part of Project "BIA2016-78460-C3-1-R" supported by the State Research Agency of Spain and the project "Rethinking coastal defence and Green-energy Service infrastructures through enHancEd-durAbiLity high-performance cement-based materials-ReSHEALience", funded by the European Union Horizon 2020 research and innovation programme under GA No 760824.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental methodology on the serviceability behaviour of reinforced ultra-high performance fibre reinforced concrete tensile elements

  • Khorami, Majid
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] Design codes include serviceability limit state (SLS) provisions for stress, crack, and deflection control in concrete structures, which may limit the structural design. When drawing on reinforced ultra-high performance fibre-reinforced concrete (R-UHPFRC), the process of cracking differs significantly from traditional concretes. Thus, it remains unclear whether the traditional provisions are applicable to R-UHPFRC or should be reviewed. Uniaxial tensile tie test is an excellent option to analyse and review these criteria. This work proposes a novel test methodology to study the behaviour of R-UHPFRC under serviceability conditions, which lets the study of the global and local deformation behaviour by using different measurement equipment. Two different types of R-UHPFRC ties with variant fibre content were tested. The global average tensile stressstrain curve, cracking behaviour, number, and width of cracks were obtained. Promising preliminary results admitted that this methodology can be useful to propose design criteria of R-UHPFRC under SLS., State Research Agency of Spain, Grant/Award Number: BIA2016-78460-C3-1-R
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Validation of a non-linear hinge model for tensile behavior of UHPFRC using a Finite Element Model

  • Mezquida-Alcaraz, Eduardo J.
  • Lopez Martinez, Juan Angel
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] Nowadays, the characterization of Ultra-High Performance Fiber-Reinforced Concrete (UHPFRC) tensile behavior still remains a challenge for researchers. For this purpose, a simplified closed-form non-linear hinge model based on the Third Point Bending Test (ThirdPBT) was developed by the authors. This model has been used as the basis of a simplified inverse analysis methodology to derive the tensile material properties from load-deflection response obtained from ThirdPBT experimental tests. In this paper, a non-linear finite element model (ELM) is presented with the objective of validate the closed-form non-linear hinge model. The state determination of the closed-form model is straightforward, which facilitates further inverse analysis methodologies to derive the tensile properties of UHPFRC. The accuracy of the closed-form non-linear hinge model is validated by a robust non-linear FEM analysis and a set of 15 Third-Point Bending tests with variable depths and a constant slenderness ratio of 4.5. The numerical validation shows excellent results in terms of load-deflection response, bending curvatures and average longitudinal strains when resorting to the discrete crack approach., This work forms part of Project "BIA2016-78460-C3-1-R" supported by the State Research Agency of Spain
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Direct procedure to characterize the tensile constitutive behavior of strain-softening and strain-hardening UHPFRC

  • Mezquida-Alcaraz, Eduardo J.
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] There is a need to establish a complete process to characterize Ultra-High-Performance Fiber-Reinforced Concrete (UHPFRC) in both strain-hardening and strain-softening tensile behavior. This process should be simple and easy to apply so that its application is direct. Therefore, this paper presents the development of a complete process to obtain the tensile constitutive parameters of UHPFRC. A simplified inverse analysis based on four-point bending tests (4PBT) to derive the tensile material properties of strain-hardening UHPFRC was adapted to be applied in the event of strain softening using a nonlinear finite element model (NLFEM). To fulfill this objective, an extensive experimental program was run with 227 UHPFRC specimens tested in 4PBT that exhibited strain-softening and strain-hardening tensile responses. As a reference, the characteristic UHPFRC tensile constitutive behavior was obtained. Finally, a predictive application capable of predicting tensile behavior using the experimental 4PBT curve as input was developed with the experimental database., This work forms part of Project "BIA2016-78460-C3-1-R" supported by the State Research Agency of Spain and the European Union's Horizon 2020 ReSHEALience Project (Grant Agreement No. 760824)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Long-term behavior of cracked fiber reinforced concrete under service conditions

  • Monetti, D.H.
  • Llano-Torre, Aitor
  • Torrijos, M.C.
  • Giaccio, G.
  • Zerbino, Raúl
  • Martí Vargas, José Rocío|||0000-0003-1665-2348
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] This paper presents an experimental study on creep behavior of cracked Fiber Reinforced Concrete (FRC). To this end, a conventional strength concrete incorporating hooked-end steel fibers was used. In order to represent service conditions, specimens under low sustained loads with small pre-cracking damage (lower than 0.5 mm) were tested and analyzed. Taking as a reference the residual stress A, determined according to EN 14651:2007, different stress levels for the creep tests were applied: 25%, 35% and 45% of f(R,1). For the pre-cracking damage, several initial crack openings were considered: 0.05, 0.1, 0.2, 0.3 and 0.5 mm. The specimens were tested under a four-point bending scheme for 180 days in controlled environmental conditions. The Crack Opening Rate (COR) was used as parameter to characterize the creep behavior of cracked FRC. After the creep tests, conventional flexural tests were carried out to evaluate the residual capacity and to survey the fiber density of each specimen. Both the stress level and the initial crack opening factors affected significantly the creep behavior. In all cases, the measured increases in crack openings resulted compatible with service conditions, and no negative effects on the residual post-creep behavior were observed. An expression to predict Crack Opening Rate values is proposed. (C) 2018 Elsevier Ltd. All rights reserved., Funding from projects CONICET PIP 112-201101-00765 Development and characterization of fiber reinforced concretes for structural applications , UNLP PPID2012 Damage processes in fiber reinforced concretes , UNLP 11/I188 Fibre reinforced concretes and their contribution to the sustainable development , all three from Argentine, and BIA2016-78460-C3-1-R Bases para el diseño de estructuras sostenibles de hormigón de muy alto rendimiento a nivel prenormativo / Diseño eficiente de estructuras de HMAR , from Spain, as well as the collaboration of Cementos Avellaneda and Maccaferri are greatly appreciated.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Serviceability behaviour of reinforced UHPFRC tensile elements: Assessment of the ratio between maximum and average crack widths

  • Khorami, M.
  • Navarro-Gregori, Juan|||0000-0002-6319-7029
  • Serna Ros, Pedro|||0000-0001-8754-1165
[EN] This study aimed to evaluate the maximum crack width formed under tensile stresses for two reinforced ultrahigh performance fibre-reinforced concrete (UHPFRC) types with different steel fibre volume contents, and to compare them to average values. The maximum crack width values can more than double the average ones based on the applied tensile strain. The difference between maximum and average crack widths should be considered for examining UHPFRC structures for the serviceability and durability design. This paper also introduces appropriate statistical procedures for developing fragility curves based on cracking data by assuming that they can be represented by Rice distribution functions., This study forms part of Project BIA2016-78460-C3-1-R, supported by the Ministry of Economy and Competitiveness of Spain.