Pasar al contenido principal

CARACTERIZACION ELECTROQUIMICA DE ELECTRODOS CERAMICOS Y APLICACION A PROCESOS ELECTROQUIMICOS DE OXIDACION AVANZADA

CTQ2015-65202-C2-1-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improvement of the Electrochemical Behavior of (Sb, Sn, Cu)O Ceramic Electrodes as Electrochemical Advanced Oxidation Anodes

  • Giner-Sanz, Juan José|||0000-0003-0441-6102
  • García Gabaldón, Montserrat|||0000-0003-4254-6733
  • Ortega Navarro, Emma María|||0000-0001-6902-018X
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
  • Sánchez-Rivera, María J.
  • Mestre, Sergio
[EN] This work explores the possibility of increasing the active surface of a Sb-doped SnO2 ceramic electrode using CuO as sintering aid, by incorporating petroleum coke as a pore generator. In order to fulfil this goal, three series of (Sb, Sn, Cu)O electrodes with different coke contents were synthetized. The properties of the electrodes, and their microstructure, change significantly as a function of the coke content before sintering. The electrochemical characterization of the synthesized electrodes showed that the coke addition before sintering causes two antagonist effects on the performance of the (Sn, Sb, Cu)O as anodes in electrochemical advanced oxidation processes (EAOP). On one hand, it significantly improves the electrochemical roughness factor of the electrode, solving the densification problem in this way. On the other hand, it worsens the electrochemical behavior of the electrode: narrowing its electrochemical window; and ¿activating¿ it slightly. The addition of coke before sintering changes the kinetic parameters, leading to a kinetic situation in which the accumulation of hydroxyl radicals is slightly lower. A balance must be sought: an intermediate coke content will improve significantly the electrochemical roughness factor of the electrode, but will only worsen slightly its electrochemical behavior, leading to an optimum (Sn, Sb, Cu)O EAOP anode., The authors are very grateful to the Ministerio de Economia y Competitividad (Projects: CTQ2015-65202-C2-1-R and CTQ2015- 65202-C2-2-R) and to the European Regional Development Fund (FEDER), for their economic support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluation of new ceramic electrodes based on Sb-doped SnO2 for the removal of emerging compounds present in wastewater

  • Mora-Gómez, Julia
  • Sánchez-Rivera, María-José
  • Mestre, Sergio
  • García Gabaldón, Montserrat|||0000-0003-4254-6733
  • Ortega Navarro, Emma María|||0000-0001-6902-018X
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
[EN] The properties of the ceramic electrodes make them interesting for electrochemical advanced oxidation processes (EAOPs), destined to the elimination of emergent or refractory contaminants, as an alternative to boron doped-diamond (BDD) electrodes. For this purpose, new ceramic electrodes based on Sb-doped SnO2 have been developed. Sb-doped tin oxide electrodes have been obtained through mechanical mixing of raw materials and sintering of dry-pressed specimens. Different sintering temperatures (1050 degrees C to 1250 degrees C) were considered. The electrochemical behavior of the resulting electrodes has been compared to that exhibited by Pt and BDDs electrodes. The oxygen discharge potential (E-02) for the ceramic electrodes decreases as the sintering temperature increases, being these values higher than that observed for the Pt electrode and smaller than that for the BDD electrode. This result in a highest rate of COD removal for the electrode sintered at 1050 degrees C comparing with the rest of ceramic electrodes under potentiostatic operation. On the other hand, in galvanostatic mode, the performance of the different ceramic electrodes in terms of the degradation of Norfloxacin, used as tested antibiotic, was similar. Comparing the behavior of the ceramic electrode sintered at 1250 degrees C and that of the BDD electrode at an applied potential of 3 V, it is inferred that although both present similar values in terms of the degradation of Norfloxacin, the rate of removal of the chemical oxygen demand is higher in the case of the BDD., The authors thanks to Ministerio de Economia y Competitividad (projects number: CTQ2015-65202-C2-1-R and CTQ2015-65202-C2-2R) and to Fondo Europeo de Desarrollo Regional (FEDER) the support to this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

CuO improved (Sn,Sb)O2 ceramic anodes for electrochemical advanced oxidation processes

  • Sánchez-Rivera, M.J.
  • Mestre, S.
  • Giner-Sanz, Juan José|||0000-0003-0441-6102
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
[EN] Antimony¿doped tin oxide electrodes with CuO as sintering aid are presented as an economical alternative to metal¿based electrodes, intended for the electrooxidation process of emerging and recalcitrant organic contaminants in wastewaters. The CuO proportion has been optimized to obtain densified electrodes with a mild thermal cycle (Tmax = 1200°C). One of the manufactured electrodes (97.8 mol.% of SnO2, 1.0 mol.% of Sb2O3, and 1.2 mol.% of CuO) was selected for electrochemical characterization from a physical and morphological analysis. The electrochemical behavior of the selected electrode showed that the addition of CuO as sintering aid widens the electrochemical window and increases the electrode ¿inactivity¿, with respect to an (Sn, Sb)O2 electrode synthesized in the same conditions. In return, the (Sn,Sb,Cu)O2 electrode presents a significantly lower electrochemical rugosity factor. Moreover, the addition of CuO does not change the oxygen evolution reaction mechanism, but it modifies the kinetic parameters, leading to a larger accumulation of hydroxyl radicals. Consequently, the addition of CuO as sintering aid significantly improves the electrochemical properties of the electrode as an electrochemical advanced oxidation process anode with respect to the (Sn,Sb)O2 electrode, at the expense of worsening its electrochemical roughness factor. The results of the electrochemical characterization were confirmed by Norfloxacin degradation tests., The authors are very grateful to the Ministerio de Economia y Competitividad (Projects: CTQ2015-65202-C2-1-R and CTQ2015-65202-C2-2-R) and to the European Regional Development Fund (FEDER), for their economic support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Using p-Si/BDD anode for the electrochemical oxidation of norfloxacin

  • Wohlmuth da Silva, Salatiel
  • Siqueira Rodrigues, Marco A.
  • Moura Bernardes, Andréa
  • Ortega Navarro, Emma María|||0000-0001-6902-018X
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
[EN] This study evaluated the electrochemical advanced oxidation process (EAOP) using boron-doped diamond (p-Si/BDD) anode in the abatement of the antibiotic norfloxacin (NOR). The influence of the applied current density (iapp), initial concentration of NOR, sodium sulfate (Na2SO4) concentration and reactor operation conditions were evaluated. The mechanism of NOR oxidation (direct or indirect) was also studied by cyclic voltammetry and chronoamperometry. The results showed that, depending on the iapp, and the NOR and Na2SO4 concentration, the NOR could be oxidized by direct electron transfer, with the carbon-sp2 impurities on the p-Si/BDD surface, and indirect, by persulfate ions (S2O82¿), sulfate (SO4·¿) and/or hydroxyl radicals (HO) electro-generated at the anode surface. When the reactor is operated favoring the electro-generated HO, NOR abatement and chemical oxygen demand (COD) reduction are simultaneous. Conversely, at the time that the reactor is operated favoring the NOR direct oxidation and by S2O82¿ and SO4·¿, NOR and COD reduction are not parallel leading to high byproducts formation. Therefore, it is important to know the matrix content (organic and sulfate content), for the correct choice of the operational parameters that will lead to a low byproducts formation., The authors thank Cyted, CNPq, CAPES/DGPU project no. 7595/14-0, FAPERGS and FINEP. The authors thank the financial support from MINECO (Ministerio de Economia y Competitividad, Spain) under project CTQ2015-65202-C2-1-R, co-financed with FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analysis of norfloxacin ecotoxicity and the relation with its degradation by means of electrochemical oxidation using different anodes

  • Montañés, Maria-Teresa|||0000-0002-2620-6926
  • García Gabaldón, Montserrat|||0000-0003-4254-6733
  • Giner-Sanz, Juan José|||0000-0003-0441-6102
  • Mora-Gómez, Julia|||0000-0002-1781-8664
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
  • Roca-Pérez, Ll.
[EN] In this work, ecotoxicological bioassays based on Lactuca sativa seeds and bioluminescent bacterium (Vibrio fischeri) have been carried out in order to quantify the toxicity of Norfloxacin (NOR) and sodium sulfate solutions, before and after treating them using electrochemical advanced oxidation. The effect of some process variables (anode material, reactor configuration and applied current) on the toxicity evolution of the treated solution has been studied. A NOR solution shows an EC50 (5 days) of 336 mg L-1 towards Lactuca sativa. This threshold NOR concentration decreases with sodium sulfate concentration, in solutions that contain simultaneously Norfloxacin and sodium sulfate. In every case considered in this work, the electrochemical advanced oxidation process increased the toxicity (towards both Lactuca sativa and Vibrio fischeri) of the solution. This toxicity increase is mainly due to the persulfate formation during the electrochemical treatment. From a final solution toxicity point of view, the best results were obtained using a BDD anode in a divided reactor applying the lowest current intensity., The authors are very grateful to the Ministerio de Economia y Competitividad (Projects CTQ2015-65202-C2-1-R and RTI2018-101341-B-C21) for their economic support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Algorithm for Assessing the Convergence of a Cyclic Voltammetry to Its Limit Cycle

  • Giner-Sanz, Juan José|||0000-0003-0441-6102
  • Ortega Navarro, Emma María|||0000-0001-6902-018X
  • García Gabaldón, Montserrat|||0000-0003-4254-6733
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
[EN] Cyclic voltammetry is one of today's standard electrochemical measurement techniques. What characterizes cyclic voltammetry is that potential is linearly ramped in cycles. In general, in this kind of measurements, the system tends to a stationary state, which is known as limit cycle. The common practice for assessing the voltammogram convergence is to perform a multicycle cyclic voltammetry, and visually compare the sequential cycles in order to see if there are significant changes from one cycle to the following one. The main limitation of visual comparison is its limited accuracy and its dependence on the analyst's subjectivity. In this work, an algorithm for quantitatively assessing the convergence of experimental cyclic voltammograms (CVs) was developed. The algorithm was successfully validated experimentally using two systems: it is able to determine whether the CV converged to its limit cycle, and when it converged. Moreover, the algorithm is able to quantify the measurement noise. The low computational cost of the developed algorithm allows to execute it in real time during the cyclic voltammetry measurement. In this way, it can be used in order to automate the measurement process which would decide, according to predefined convergence criteria, when to stop cycling., The authors are very grateful to the Generalitat Valenciana (Vali+d postdoctoral grant APOSTD/2018/001), to the Ministerio de Economia y Competitividad (Project CTQ2015-65202-C2-1-R), to the European Regional Development Fund (FEDER) and to the European Social Fund, for their economic support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of the CuO addition on a Sb-doped SnO2 ceramic electrode applied to the removal of Norfloxacin in chloride media by electro-oxidation

  • Carrillo Abad, Jorge
  • Mestre, S.
  • Mora-Gómez, Julia|||0000-0002-1781-8664
  • García Gabaldón, Montserrat|||0000-0003-4254-6733
  • Ortega Navarro, Emma María|||0000-0001-6902-018X
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
[EN] Norfloxacin is employed as in veterinary and human medicine against gram-positive and gram-negative bacteria. Due to the ineffective treatment at the wastewater treatment plants it becomes an emergent pollutant. Electro-oxidation appears as an alternative to its effective mineralization. This work compares Norfloxacin electro-oxidation on different anodic materials: two ceramic electrodes (both based on SnO2 + Sb2O3 with and without CuO, named as CuO and BCE, respectively) and a boron doped diamond (BDD). First, the anodes were characterized by cyclic voltammetry, revealing that NOR direct oxidation occurred at 1.30 V vs. Ag/AgCl. The higher the scan rate the higher both the current density and the anodic potential of the peak. This behavior was analyzed using the Randles¿Sevcik equation to calculate the Norfloxacin diffusion coefficient in aqueous media, giving a value of D= 7.80¿10-6 cm2 s-1 at 25 °C), which is close to the predicted value obtained using the Wilke-Chang correlation. The electrolysis experiments showed that both NOR and TOC decay increased with the applied current density, presenting a pseudo-first order kinetic. All the anodes tested achieved more than 90% NOR degradation at each current density. The CuO is not a good alternative to BCE because although it acts as a catalyst during the first use, it is lost from the anode surface in the subsequent uses. According to their oxidizing power, the anodes employed are ordered as follows: BDD>BCE>CuO., The authors want to express their gratitude to the Ministerio de Economia y Competitividad (Spain) and the FEDER funds, which financially support the projects CTQ2015-65202-C2-1-R, CTQ201565202-C2-2-R and RTI2018-101341-B-C21.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of the atenolol degradation using a Nb/BDD electrode in a filter-press reactor

  • Heberle, Alan Nelson Arenhart
  • BERNARDES, ANDREA MOURA
  • García Gabaldón, Montserrat|||0000-0003-4254-6733
  • Ortega Navarro, Emma María|||0000-0001-6902-018X
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
[EN] The present paper deals with the atenolol (ATL) degradation by advanced anodic oxidation using a boron-doped diamond anode supported on niobium (Nb/BDD). Cyclic voltammetry performed on this electrode revealed that it presents a high quality (diamond-sp3/sp2-carbon ratio), high potential for OER and that ATL can be oxidized directly and/or indirectly by the electrogenerated oxidants, such as hydroxyl radicals, persulfate ions and sulfate radicals. Electrolysis experiments demonstrated that ATL degradation and mineralization follow a mixed (first and zero) order kinetics depending on the applied current density. At high applied current densities, the amount of OH radicals is very high and the overall reaction is limited by the transport of ATL (pseudo first-order kinetics) whereas for low applied current densities, the rate of OH radicals generation at the anode is slower than the rate of arrival of ATL molecules (pseudo-zero order kinetics). Estimated values of kzero and kfirst based on the assumption of pseudo-zero or pseudo-first order kinetics were carried oud as a function of the supporting electrolyte concentration, indicating that both parameters increased with its concentration due the higher production of sulfate reactive species that play an important role in degradation. Finally, MCE increased with the decrease of current density, due to the lower amount of OH present in solution, since this species could be rapidly wasted in parasitic reactions; and the increase of sulfate concentration due to the more efficient production of persulfate., The authors thank the financial support from the Ministerio de Economía y Competitividad (Spain) under projects CTQ2015-65202-C2-1-R and RTI2018-101341-B-C21, co-financed with FEDER funds. The authors thank to FAPERGS, CAPES, FINEP and CNPQ.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Theoretical Determination of the Stabilization Time in Galvanostatic EIS Measurements: The Simplified Randles Cell

  • Giner-Sanz, Juan José|||0000-0003-0441-6102
  • Ortega Navarro, Emma María|||0000-0001-6902-018X
  • García Gabaldón, Montserrat|||0000-0003-4254-6733
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
[EN] Usually, EIS measurements are performed in 2 steps: a stabilization step followed by an acquisition step. The first is necessary in order to ensure that the impedance is determined when the system has reached its stationary state. In this work, a theoretical framework is proposed for estimating the required stabilization time for EIS measurements. Here, it was applied to the simplest case: the simplified Randles cell. In order to calculate the required stabilization time for performing EIS measurements, a theoretical dynamic model of a Randles cell under galvanostatic sinusoidal perturbation was developed. The proposed model can be used to estimate, from a theoretical point of view, the required stabilization time for performing EIS measurements in a Randles-like system. Even though, this work focuses on the simplest case, the developed theoretical framework can be applied to any system, however complex it may be., The authors are very grateful to the Generalitat Valenciana (Vali+d postdoctoral grant APOSTD/2018/001), to the Ministerio de Economia y Competitividad (Project CTQ2015-65202-C2-1-R), to the European Regional Development Fund (FEDER) and to the European Social Fund, for their economic support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Electrochemical degradation of norfloxacin using BDD and new Sb-doped SnO2 ceramic anodes in an electrochemical reactor in the presence and absence of a cation-exchange membrane

  • Mora-Gómez, Julia|||0000-0002-1781-8664
  • Ortega Navarro, Emma María|||0000-0001-6902-018X
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
  • García Gabaldón, Montserrat|||0000-0003-4254-6733
  • Mestre, S.
[EN] Electrochemical oxidation of Norfloxacin (NOR) in sodium sulphate media has been comparatively studied in an undivided and in a divided electrolytic cell both containing either a boron doped diamond (BDD) or a novel Sb-doped SnO2 ceramic anode under galvanostatic operation. The electro-oxidation was found to occur with first order kinetics mainly when using both anodes. The results showed the great oxidizing power of BDD in relation to the ceramic anode to convert NOR and all the intermediate accumulated into CO2. In the case of the BDD, although a 92% of TOC abatement was achieved, the complete mineralization was not possible probably due to the carboxylic acids still present in solution. On the contrary, for the ceramic electrode, which presented a maximum value of TOC removal of about 63%, the total mineralization of the aromatic oxidation intermediates was not reached under the experimental conditions. The use of a membrane divided cell showed positive aspects in terms of molecule degradation, degree of mineralization and current efficiency since prevents the intermediate products formed during the NOR oxidation process from being reduced on the cathode.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Electrochemical Degradation of Reactive Black 5 using two-different reactor configuration

  • Droguett, Tamara
  • Mestre, Sergio
  • Cifuentes, Gerardo
  • Mora-Gómez, Julia|||0000-0002-1781-8664
  • García Gabaldón, Montserrat|||0000-0003-4254-6733
  • Ortega Navarro, Emma María|||0000-0001-6902-018X
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
[EN] Novel Sb-doped SnO2 ceramic electrodes sintered at different temperatures, are applied to the degradation of Reactive Black 5 in both divided and undivided electrochemical reactors. In the undivided reactor the discoloration of the solution took place via the oxidation of RB5 dye, without the corresponding reduction in the chemical oxygen demand for the ceramic electrodes. However, in the divided one, it was possible to achieve the discoloration of the solution while at the same time decreasing the chemical oxygen demand through the ·OH-mediated oxidation, although the chemical oxygen demand degradation took place at a slower rate., The authors thank the financial support from the Ministerio de Economia y Competitividad (Spain) under projects CTQ2015-65202-C2-1-R and RTI2018-101341-B-C21, co-financed with FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of pore generator on microstructure and resistivity of Sb2O3 and CuO doped SnO2 electrodes

  • Sánchez-Rivera, M.-J.
  • Gozalbo, A.
  • Mestre, S.
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
[EN] Sb(2)O(3)and CuO doped SnO(2)ceramic electrodes could be an alternative to the ones currently used ones in the electrooxidation process of water pollutants. The rise of electrode surface by introducing a porogen agent on the composition was analysed in order to increase the electrochemical active surface. For this reason, several substances were tested. Although the densification and total pore volume had similar values, the microstructures and the pore size distributions generated were strongly dependent on porogen nature. A total of five porogens were tested, but petroleum coke turned out to be the best option for these electrodes. It was found that the electrical resistivity depends on the nature of pore generator. Furthermore, its relation to the porosity can be modelled with Archie's or Pabst's equations., The authors are very grateful to the Ministerio de Economia y Competitividad (Projects: CTQ2015-65202-C2-1-R and CTQ2015-65202-C2-2-R) and to the European Regional Development Fund (FEDER), for their economic support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental design applied to improving theeffect of bismuth oxide as a sintering aid for tin oxide, Diseño experimental aplicado a la mejora del efecto del óxido de bismuto como promotor de sinterización del óxido de estano

  • Sánchez-Rivera, María-José
  • Gozalbo, Ana
  • Mestre, Sergio
  • Pérez-Herranz, Valentín|||0000-0002-4010-0888
[ES] El óxido de estano¿ es un material ampliamente estudiado dada su gran variedad de aplicaciones. Sin embargo, debido a que sinteriza sin densificar, su procesado requiere la incorporación de promotores de la sinterización. Se ha estudiado el comportamiento de 3 mezclas a base de óxido de estano¿ que contenían óxido de bismuto como promotor de la sinterización, en proporciones 1-2%mol. A través de un diseno¿ factorial de experimentos 2 3 , se han evaluado los efectos de los parámetros del tratamiento térmico (velocidad de calentamiento, temperatura máxima y tiempo de permanencia) sobre la densificación. La combinación de una adecuada proporción de Bi2O3 (alrededor del 1,5%), una velocidad de calentamiento rápida (15 ¿C·min¿1 ) y una temperatura de sinterización elevada (1.300 ¿C), permite alcanzar una densificación del 45%. Sin embargo, el tiempo de permanencia no ejerce un efecto significativo. Se propone una interpretación de los efectos significativos sobre la densificación, basada en el comportamiento termodinámico de los compuestos que contienen Bi y en los mecanismos de transporte de materia., [EN] Tin oxide has been extensively studied due to its wide variety of applications. However, its poor sinter ability requires the use of sintering aids for its processing. The sintering behaviour of three different SnO2-based powder mixtures, containing Bi2O3 in amounts between 1 and 2 mol%, has been analyzed. The effects of thermal treatment parameters (heating rate, maximum temperature and soaking time) on the densification were obtained by a factorial experimental design 2(3). Bi2O3 adequate proportion (around 1.5%) combined with a fast heating (15 degrees C min(-1)) and a high maximum temperature (1300 degrees C), allows reaching densifications around 45%. However, soaking time has no significant effect over densification. An interpretation of the significant effects has been proposed based on thermodynamic behaviour of Bi-containing compounds and the mass transport mechanisms. (C) 2017 SECV. Published by Elsevier Espana, S.L.U., The authors thank to Ministerio de Economia y Competitividad and Fondo Europeo de Desarrollo Regional for the support to this research [Plan Nacional de I + D, project Ref. CTQ2015-65202-C2-2-R (MINECO/FEDER)].