Pasar al contenido principal

HYPER-VIRTUAL: Diseño y optimización de un prototipo virtual de un sistema de transporte terrestre a muy alta velocidad en condiciones de presión próximas al vacío

DI-17-09616

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Formación
Convocatoria Doctorados Industriales
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario ZELEROS GLOBAL S.L.

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

CFD Simulation of a Hyperloop Capsule Inside a Low-Pressure Environment Using an Aerodynamic Compressor as Propulsion and Drag Reduction Method

  • Lluesma-Rodríguez, Federico
  • Gonzalez, Temoatzin
  • Hoyas, Sergio|||0000-0002-8458-7288
[EN] One of the most restrictive conditions in ground transportation at high speeds is aerodynamic drag. This is even more problematic when running inside a tunnel, where compressible phenomena such as wave propagation, shock waves, or flow blocking can happen. Considering Evacuated-Tube Trains (ETTs) or hyperloops, these effects appear during the whole route, as they always operate in a closed environment. Then, one of the concerns is the size of the tunnel, as it directly affects the cost of the infrastructure. When the tube size decreases with a constant section of the vehicle, the power consumption increases exponentially, as the Kantrowitz limit is surpassed. This can be mitigated when adding a compressor to the vehicle as a means of propulsion. The turbomachinery increases the pressure of part of the air faced by the vehicle, thus delaying the critical conditions on surrounding flow. With tunnels using a blockage ratio of 0.5 or higher, the reported reduction in the power consumption is 70%. Additionally, the induced pressure in front of the capsule became a negligible effect. The analysis of the flow shows that the compressor can remove the shock waves downstream and thus allows operation above the Kantrowitz limit. Actually, for a vehicle speed of 700 km/h, the case without a compressor reaches critical conditions at a blockage ratio of 0.18, which is a tunnel even smaller than those used for High-Speed Rails (0.23). When aerodynamic propulsion is used, sonic Mach numbers are reached above a blockage ratio of 0.5. A direct effect is that cases with turbomachinery can operate in tunnels with blockage ratios even 2.8 times higher than the non-compressor cases, enabling a considerable reduction in the size of the tunnel without affecting the performance. This work, after conducting bibliographic research, presents the geometry, mesh, and setup. Later, results for the flow without compressor are shown. Finally, it is discussed how the addition of the compressor improves the flow behavior and power consumption of the case., This research was funded by Mineco/FEDER grant number RTI2018-102256-B-I00 and the author Federico Lluesma-Rodriguez was partially funded by Ministerio de Ciencia, Innovacion y Universidades under the grant "Doctorandos Industriales" number DI-17-09616.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

CFD simulation of a hyperloop capsule inside a closed environment

  • Lluesma-Rodríguez, Federico
  • González, Temoatzin
  • Hoyas, Sergio|||0000-0002-8458-7288
[EN] One of the most restrictive conditions in ground transportation is traveling through a tunnel at high speed. In those conditions waves are propagated, increasing the pressure upstream the object, and so, the drag compared to the open flow case. Although this drawback is mitigated with larger tunnels, another proposed solution is to decrease the pressure inside the tunnel. In this paper it is demonstrated that the drag coefficient is almost invariant with the pressure conditions. This effect allows, not only to have smaller tunnels with respect to the existing for standard trains, but also to enhance the speed of the train without increasing its aerodynamic losses., SH and FLR work have been supported by project RTI2018-102256-B-I00 of Mineco/FEDER. FLR is partially funded buy MCIU under grant DI-17-09616.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Approximation of the Couette-Poiseuille flow on an annular domain in compressible regime for a hyperloop pod.

  • Lluesma-Rodríguez, Federico
  • Hoyas, Sergio|||0000-0002-8458-7288
[EN] Fanno flow is one of the most studied problems in fluid mechanics, as it models the pressure losses on domains in which the characteristic length is considerably lower than the height. These types of flows are present in several applications in the industry, such as pipe flows in pneumatic and hydraulic circuits, oil pipelines or air conditioning and water distribution systems. One potential application can be found in hyperloop design, where flow at high speeds moves between the small gap between the capsule and the tube wall. In this case, the domain is annular-shaped instead of a single cylinder, and the interior wall moves at the capsule speed. Although this quasi-1D flow is strongly affected by the wall friction, it cannot be modelled using the standard Fanno expression. Thus, to model the pressure drop without extensive CFD techniques, a simplified 1D analytical expression is developed to estimate the friction losses. The model assumes a constant ratio between the shear stress on the interior and the exterior walls throughout the channel. Then, instead of the hydraulic diameter as in the standard Fanno expression, a new definition of an equivalent diameter is performed to consider the annular-shaped domain and the movement of the interior wall. The new equivalent diameter is always higher than the original used for Fanno flows (hydraulic one), even twice when the wall speed equals the mean speed. This effect leads to smaller pressure losses due to the movement of one of the walls and indicates that the wall movement is always beneficial. To validate the results obtained from the model, they are compared with an equivalent CFD simulation, leading to a maximum deviation of 5% on the Mach number and 7% on the total friction coefficient., The authors would like to thank Ministerio de Ciencia, Innovación y Universidades for the grant provided to support this work, grant number DI-17-09616. SH is funded by the project PID2021-128676OB-I00 by FEDER/MCIN.