Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A particle swarm optimization algorithm with novelty search for combustion systems with ultra-low emissions and minimum fuel consumption

  • Martínez-Rodríguez, David|||0000-0002-2093-7840
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • Villanueva Micó, Rafael Jacinto|||0000-0002-0131-0532
  • Fernandes, Cássio
  • Lucchini, Tommaso
  • Della Torre, Augusto
  • Hidalgo, J. Ignacio
[EN] The particle swarm optimization algorithm is primarily inspired by the natural behaviour of swarms and achieves important results in different applications. However, it is not exempt from stagnation in local optima and has a tendency to prematurely converge to them. Novelty Search is a concept that appeared recently in different fields of computational intelligence. It aims at exploring non-visited areas of the search space through solutions that bring novelty to already discovered solutions. The novelty of this work can be divided into two steps: on one side, this article proposes a variant of the particle swarm optimization algorithm which uses Novelty Search concepts to improve the algorithm¿s performance. Our proposal is first checked and compared using the CEC 2005 benchmark suite and then, we apply it to solve a real-world optimization problem: the design of a combustion system targeting the reduction of pollutant emissions and fuel consumption. The combustion chamber design phase usually is a complex and time-consuming process even with advanced supercomputers, since it depends on several input variables which are highly non-linear and with crossed interaction. Then, the second contribution of this work is to develop a methodology that couples a computational fluid dynamics (CFD) simulation tool with the new optimization algorithm for minimizing the specific fuel consumption of a compression-ignited engine, while constraining the NOx and soot emissions. A 3D-CFD model of the combustion system was built to predict and analyse the performance of the combustion system and hence, select the parameters with a higher impact on the system. The method reduces the computational time and includes tools for the automatic preparation of the input parameters and geometry of the system. The input parameters correspond to geometrical variables that control the bowl shape, the number of holes in the injector, the injection pressure, the swirl number and the exhaust gas recirculation rate. Results show how the simulation tool and the new PSO with Novelty Search algorithm allow us to obtain a new combustion system that minimizes the fuel consumption by 3%, simultaneously reducing NOx and soot emissions., This work has been partially supported by This work has been supported by the grant PID2020-1152 70GB I00 funded by MCIN/AEI/10.13039/501100011033; European Union FEDER funds; Spanish Ministerio de Economía y Competitividad through Grants PID2021-125549OB-I00 and PDC2022-133429-I00. The author C. S. Fernandes thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI-2019-S2- 20-555), which is included within the framework of Programa de Apoyo para la Investigacion y Desarrollo (PAID).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Combustion Modeling Approach for the Optimization of a Temperature Controlled Reactivity Compression Ignition Engine Fueled with Iso-Octane

  • Pelosin, Mattia
  • Spohr-Fernandes, Cássio
  • Lucchini, Tommaso
  • Marmorini, Luca
  • Zhou, Qiyan
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
[EN] In this study, an innovative Low Temperature Combustion (LTC) system named Temperature Controlled Reactivity Compression Ignition (TCRCI) is presented, and a numerical optimization of the hardware and the operating parameters is proposed. The studied combustion system aims to reduce the complexity of the Reaction Controlled Compression Ignition engine (RCCI), replacing the direct injection of high reactivity fuel with a heated injection of low reactivity fuel. The combustion system at the actual state of development is presented, and its characteristics are discussed. Hence, it is clear that the performances are highly limited by the actual diesel-derived hardware, and a dedicated model must be designed to progress in the development of this technology. A Computational Fluid Dynamics (CFD) model suitable for the simulation of this type of combustion is proposed, and it is validated with the available experimental operating conditions. The Particle Swarm Optimization (PSO) algorithm was integrated with the Computational Fluid Dynamic (CFD) software to optimize the engine combustion system by means of computational simulation. The operating condition considered has a relatively high load with a fixed fuel mass and compression ratio. The parameters to optimize are the piston bowl geometry, injection parameters and the boosting pressure. The achieved system configuration is characterized by a wider piston bowl and injection angle, and it is able to increase the net efficiency of 3% and to significantly reduce CO emissions from 0.407 to 0.136 mg., This research has been supported by Grant UPV-SOLGEN-79674 funded by Universitat Politecnica de Valencia. This research has been supported by Grant CIPROM/2021/061 funded by Generalitat Valenciana. The author C. S. Fernandes thanks the Universitat Politècnica de València for his predoctoral contract (FPI-2019-S2-20-555), which is included within the framework of Programa de Apoyo para la Investigación y Desarrollo (PAID).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Combustion system optimization for the integration of e-fuels (Oxymethylene Ether) in compression ignition engines

  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • Spohr-Fernandes, Cássio
  • Lucchini, Tommaso
[EN] In this study, a numerical methodology for the optimization of the combustion chamber in compression ignited engines using OME as fuel is presented. The objective is to obtain a dedicated combustion system for an engine that is fueled with this alternative fuel improving the efficiency and reducing the emissions of NOx. This article proposes the integration between the optimization algorithm and CFD codes to evaluate the behavior of an engine fuelled with the low sooting fuel OME. Based on a diesel model validated against experimental data, a further model for OME fuel was implemented for evaluating the performance of the engine. The particle swarm algorithm (PSO) was modified based on the Novelty Search concepts and used as optimization algorithm. Several tools are coupled in order to create each CFD case where all the tools and optimization algorithm are coupled in a routine that automates the entire process. The result is an optimized combustion system that provides an increase of the efficiency (about 2.2%) and a NOx reduction (35.7%) in comparison with the baseline engine with conventional fuel. In addition, a neuronal network was trained with all the results of all simulations performed during the optimization process, studying the influence of each parameter on the emissions and efficiency. From this analysis it was concluded that the EGR rate and injection pressure affects the NOx emissions with a range of variability of 63% and 38% respectively., The work has been partially supported by the Spanish Ministerio de Economia, Industria y Competitividad through Grant No TRA2017-89139-C2-1-R "Desarrollo de modelos de combustion y emisiones HPC para el analisis de sistemas de transporte sostenibles" The author C. S. Fernandes thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI-2019-S2-20-555) , which is included within the framework of Programa de Apoyo para la Investigacion y Desarrollo (PAID)