Pasar al contenido principal

LASERES DE ALTO RENDIMIENTO BASADOS EN PELICULAS DELGADAS DE MATERIALES ORGANICOS E HIBRIDOS.

MAT2015-66586-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario UNIVERSIDAD DE ALICANTE
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Are electron affinity and Ionization potential intrinsic parameters to predict the electron or hole acceptor character of amorphous molecular materials?

  • Louis, Enrique
  • San-Fabián, Emilio
  • Díaz-García, María A.
  • Chiappe, Guillermo
  • Vergés, José A.
Organic light emitting diodes (OLEDs) are current-driven devices that utilize light emission from excited states of molecules.(1) Operating OLEDs involves charge injection from the anode and the cathode into the adjacent organic layers, transport of injected charge carriers through the organic layers, and exothermic recombination of holes and electrons to generate electronically excited states of molecules. Subsequent deactivation of molecules produces electroluminescence (EL) that goes out of the device. Attaining high quantum efficiency for EL requires: (i) efficient charge injection from both electrodes into the adjacent organic layers at low drive voltage, (ii) charge balance, and (iii) confinement of charge carriers within the emitting layer to increase the probability of emissive recombination. The insertion of hole-acceptor and electron-acceptor layers between the electrodes and the emitting layer substantially increases efficiency. A multilayer structure of OLED’s consists of the emitting layer sandwiched between hole- and electron-acceptor layers that in turn are in contact with the metallic anode and cathode, respectively. Amorphous molecular materials have been proven to show several characteristics that qualify them as excellent materials to be used in OLED’s.(1) Their most remarkable feature is that, due to their homogeneous and isotropic properties, they form smooth thin films, allowing uniform contact with the metallic electrodes and between organic layers. An issue concerning nomenclature is here worthy of comment. As stated above, device operation involves three main processes, namely, charge injection, charge transport, and light emission. Although in this work we will only focus on the first, we shall also use the accepted terminology of hole- or electron-transporters, being aware of the fact that the correct one would be “acceptors” instead of ‘transporters” (investigating their transport performance(2) would require considering also carrier mobility). Hereafter both terminologies will be used indifferently., Financial support by the Spanish “Ministerio de Economía y Competitividad MINECO” and the European Union through FEDER funds (Grants FIS2012-35880, FIS2015-64222-C2-1-P, FIS2015-64222-C2-2-P, and MAT2015-66586-R) and the Universidad de Alicante, is gratefully acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Transport and optical gaps in amorphous organic molecular materials

  • San-Fabián, Emilio
  • Louis, Enrique
  • Díaz-García, María A.
  • Chiappe, Guillermo
  • Vergés, José A.
[EN] The standard procedure to identify the hole- or electron-acceptor character of amorphous organic materials used in OLEDs is to look at the values of a pair of basic parameters, namely, the ionization potential (IP) and the electron affinity (EA). Recently, using published experimental data, the present authors showed that only IP matters, i.e., materials with IP > 5.7 (<5.7) showing electron (hole) acceptor character. Only three materials fail to obey this rule. This work reports ab initio calculations of IP and EA of those materials plus two materials that behave according to that rule, following a route which describes the organic material by means of a single molecule embedded in a polarizable continuum medium (PCM) characterized by a dielectric constant ε. PCM allows to approximately describe the extended character of the system. This “compound” system was treated within density functional theory (DFT) using several combinations of the functional/basis set. In the preset work ε was derived by assuming Koopmans’ theorem to hold. Optimal ε values are in the range 4.4–5.0, close to what is expected for this material family. It was assumed that the optical gap corresponds to the excited state with a large oscillator strength among those with the lowest energies, calculated with time-dependent DFT. Calculated exciton energies were in the range 0.76–1.06 eV, and optical gaps varied from 3.37 up to 4.50 eV. The results are compared with experimental data., Financial support by the Spanish Ministerio de Economía y Competitividad MINECO and the European Union through FEDER funds (grants FIS2012-35880, FIS2015-64222-C2-1-P, FIS2015-64222-C2-2-P and MAT2015-66586-R) and the Universidad de Alicante, is gratefully acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Unveiling photophysical and photonic phenomena by means of optical gain measurements in waveguides and solutions

  • Cerdán, L.
  • Anni, Marco
  • de Giorgi, Maria Luisa
  • Boj, Pedro G.
  • Díaz-García, María A.
10 pags., 7 figs., The increasing number of solution-processed laser compounds that can be implemented as low-cost, flexible, and/or integrated devices, makes necessary the development of reliable methods to delineate all their amplifying signatures and thus to open the door to appropriate cross-sample comparisons. Seeking to solve this problem, a new formalism to retrieve the losses and the optical gains from Amplified Spontaneous Emission (ASE) spectra as a function of the excitation density has been recently reported. In this manuscript, we explore the potential of this methodology to unveil relevant information on the photonic properties of the waveguiding devices and on the photophysics of the active materials. We demonstrate that the Variable Pump Intensity method opens the door to understand the relationship between the ASE thresholds and the optical gains and losses, it enables the extraction of the scattering/modal losses of the passive devices, and it can unveil the presence of leaky-modes and excited state absorption. In contrast, it does not perform too well in samples with multiple active species in its current implementation. We have substantiated all these findings using organic semiconductor thin films, several dye-doped polymer thin films and solutions of boron hydride., The researchers from the University of Alicante and LC acknowledge financial support from the Spanish Ministerio de Economía y Competitividad (MINECO) and the European FEDER funds through Grant numbers MAT2015-66586-R and MAT2017-83856-C3-1, respectively.