Pasar al contenido principal

COMPUESTOS CERAMICA-METAL Y ALEACIONES REFRACTARIAS DE W PARA SU APLICACION BAJO CONDICIONES DE SERVICIO SEVERAS: DISEÑO MICROESTRUCTURAL Y NUEVAS RUTAS DE PROCESAMIEN

MAT2015-70780-C4-1-P

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D Printing of Photocatalytic Filters Using a Biopolymer to Immobilize TiO2 Nanoparticles

  • Sangiorgi, A.
  • González Granados, Zoilo
  • Ferrández-Montero, Ana
  • Yus, Joaquín
  • Sánchez-Herencia, A. Javier
  • Galassi, C.
  • Sanson, A.
  • Ferrari, Begoña
Titanium oxide-based photocatalytic filters were produced by Fused Deposition Modelling (FDM) using biopolymers obtained from renewable biomass resources. The thermoplastic route allows shaping composites through the immobilization of photoactive TiO2 nanoparticles in an environmentally friendly bioplastic such as the polylactic acid (PLA). Composites with an inorganic charge of 30 wt% of TiO2 nanoparticles (NPs) exhibit a 100% methyl orange (MO) degradation after 24 h of light exposition due to the extremely uniform dispersion of the nanophase within the polymer matrix in the FDM feedstock. Surface modification of TiO2 NPs allows the optimization of the colloidal dispersion and stabilization of the inorganic charge in a PLA solution and hence, the optimal distribution of nano-photoactive points in the TiO2/PLA filaments and scaffolds. The proposed new route of processing improves the dispersion of nano-charges comparing with the traditional thermo-pressing routes used for mixing thermoplastics based composites, avoiding the thermal degradation of the polymer and providing a customised product. In this manuscript the evolution of photodegradation with the increase of TiO2 content in the composite and the variation of the filter geometry was evaluated., Authors acknowledge the support to the projects S2018/NMT-4411 (Comunidad de Madrid) and MAT2015-70780-C4-1 (MINECO/FEDER). Z. Gonzalez acknowledges the Spanish Ministry of Economy and Competitiveness for the Postdoctoral Fellowship: IJCI-2016-28538. J. Yus acknowledges to the Comunidad de Madrid the support from the Youth Employment Initiative, CAMPD17_ICV_002. The authors thank ECERS for funding on Mobility Project JECS Trust Contract number: 2017294., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Semiconductor water-based inks: Miniaturized NiO pseudocapacitor electrodes by inkjet printing

  • Yus, Joaquín
  • González Granados, Zoilo
  • Sánchez-Herencia, A. Javier
  • Sangiorgi, A.
  • Sangiorgi, N.
  • Gardini, D.
  • Sanson, A.
  • Galassi, C.
  • Caballero Cuesta, Amador
  • Morales, Julián
  • Ferrari, Begoña
The formulation, development and optimization of water-based inks of platelet-like nanoparticles are the mainobjective of this work. As-synthesized Ni(OH)2nanoparticles were dispersed and stabilized in aqueous sus-pension by PEI addition. The combination of DEG (cosolvent) with H2O shows the ideal values of surface tensionand viscosity for piezoelectric inkjet printing, which exhibits a homogeneous jettingflow of the nanoplateletssuspension. The printed nanostructure was sintered at low temperature (325 °C) and the electrochemicaloverview of NiO electrode behavior was described. These printable pseudocapacitors tested by a three-electrodecell have showed a competitive specific capacitance, leading 92% and 78% of capacitance retention for 2000cycles at scan rates of 1 and 2 A/g respectively, and a coulombic efficiency of 100%. The initial performance ofthis printed NiO pseudocapacitor can be compared with others prepared by conventional methods. This newfinding is expected to be particularly useful for the designing of micro-pseudocapacitors., The authors thank ECERS for funding this project through the JECSTrust grant under the contract 2017141, and the support to the projects S2018/NMT-4411 (Comunidad de Madrid) and MAT2015-70780-C4-1and MAT2017-87541-R (MINECO/FEDER). J. Yus acknowledges the Comunidad de Madrid for the support from the Youth Employment Initiative, CAMPD17_ICV_002. Z. Gonzalez acknowledges thePostdoctoral Fellowship: IJCI-2016-28538, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Understanding of wetting and solubility behavior of Fe binder on Ti(C,N) cermets

  • Alvaredo Olmos, Paula
  • Dios Pérez, Miguel de
  • Ferrari, Begoña
  • Gordo Odériz, Elena
Given the great interest generated in the last years by the searching of new binders in hard materials, a work methodology has been created that allows the design of new metal – ceramic combinations. It includes the study of the solubility between the new binder and the reinforcement during the design of the binder composition combined with the knowledge of the sintering behavior of the cermet by monitoring the contact angle of the liquid phase formed at high temperature. Iron is considered as the main alternative binder in cermets; however, proper compositions are still under development as it is necessary to improve the sintering. This work propose the use of Ni as sintering aid to improve the wettability without the introduction of secondary phases. The article shows a comprehensive study of the high temperature behavior, in terms of solubility and wettability, of the system Fe-Ti(C,N) compared with the study of the conventional system Ni-Ti(C,N). Results show that the highest difference between Fe and Ni binders is the better wetting behavior of Ni binder, but the contact angle of liquid Fe is largely reduced by the addition of a small quantity of Ni. This fact opens the possibility to replace Ni as binder by a less toxic and cheaper binder., The authors would like to acknowledge thefinancial supportfrom the Spanish Government through the project MAT2015-70780-C4-2-P, MAT2015-70780-C4-1-P, and the Regional Govern-ment of Madrid through the program MULTIMAT-CHALLENGE, ref.S2013/MIT-2862, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mechanical characterization of Ti(C,N)-based cermets fabricated through different colloidal processing routes

  • Dios Pérez, Miguel de
  • Kraleva, Irina
  • González Granados, Zoilo
  • Alvaredo Olmos, Paula
  • Ferrari, Begoña
  • Gordo Odériz, Elena
  • Bermejo, R.
In this work the influence of different colloidal processing routes on the mechanical behavior of several Ti(C,N)-based cermets has been studied. The materials were designed with a Ti(C,N) content ranging between 80 and 85 vol %, in a Fe-Ni alloy matrix (with and without carbon addition). Three processing techniques were investigated: (i) Slip Casting (SC), (ii) Slip Casting + Cold Isostatic Pressing (SC+CIP), and (iii) Spray-Dry + Uniaxial Pressing (SDP). Biaxial strength distributions were determined in all samples using the ball-on-three-balls (B3B) method on disc-shaped specimens. Results were interpreted in the framework of Weibull theory. The characteristic strength ranged between 1090 MPa and 1870 MPa. A fractographic analysis performed on selected specimens showed different critical flaws, depending on the processing route, related to the composition and porosity level in each case. Single Edge V-Notched Beam (SEVNB) specimens fabricated with SDP were tested under 4-point-bending, in order to identify the effect of Fe-Ni content and carbon addition on their fracture resistance. Detailed fractographic analyses revealed slightly different mechanisms of fracture associated with the Fe-Ni and carbon content. Fracture toughness values ranging between ∼12 and ∼14 MPa m were measured. Based upon these findings the SDP route is proposed to improve both the strength and toughness of Ti(C,N) cermets, which can be enhanced by the addition of carbon during the colloidal processing., The authors acknowledge thefinancial support from the Span-ish Government through the projects MAT2015-70780-C4-1-P and MAT2015-70780-C4-2-P, and the Regional Government of Madrid through the program MULTIMAT-CHALLENGE, ref. S2013/MIT-2862. M.Dios acknowledges MINECO through the grant BES-2013-065760, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Heteroacoagulation of lignocellulose fibers-based biotemplates and functionalized TiO2 nanoparticles to tailor film microstructures

  • González Granados, Zoilo
  • Yus, Joaquín
  • Bravo, Yessica
  • Sánchez-Herencia, A. Javier
  • Rodríguez, Alejandro
  • Dewalque, Jennifer
  • Manceriu, Laura
  • Henrist, Catherine
  • Ferrari, Begoña
[EN] The heterocoagulation of lignocellulose nanofibers (LCNFs) with functionalized TiO nanoparticles (NPs) is presented as an innovative revalorization strategy for the exploitation of lignocellulose wastes. Their use as bio-templates could be considered a promising alternative in a current biorefinery scheme, since the massive production of porous materials in numerous nanotechnological applications, could offer new alternatives of exploitation. The surface modification of TiO NPs by adsorption of polyetilenimine (PEI) favors its anchorage with LCNFs through a peptide bond during heterocoagulation in aqueous suspension. The functionalization of LCNFs with TiO NPs results in organic–inorganic core–shell nanostructures, used to shape coatings by dipping, and sinter them at low temperature (450 °C). In this process, the LCNFs were used as endo-templates for shaping stable porous coatings, when they burn during the consolidation of the inorganic structure. In this work, the successful inclusion and homogeneous distribution of biomaterials (LCNF templates) in the semiconductor inorganic microstructure is discussed in terms of dye loading (by UV–Visible Spectroscopy), photovoltaic efficiency and charge transfer (by Electrochemical Impedance Spectroscopy, EIS) in a Dye Sensitized Solar Cell (DSSC). Results confirm that the TiO/template network yielded better photoefficiency and electron transport properties than mesoporous films assembled only from TiO NPs. The preparation of TiO-based photoanodes with enhanced performance (with an efficiency value around 6%, for a thickness of 8.7 µm) allows validating the successful colloidal procedure herein employed., The authors thank the support to the projects S2018/NMT-4411 (Comunidad de Madrid) and MAT2015-70780-C4-1 (MINECO/FEDER). Z. Gonzalez acknowledges to the European Ceramic Society for the funds of the ‘‘Frontiers of Research’’ program and also to the Spanish Ministry of Economy and Competitiveness for the Postdoctoral Fellowship: IJCI-2016-28538
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Understanding the effects of different microstructural contributions in the electrochemical response of Nickel-based semiconductor electrodes with 3D hierarchical networks shapes

  • Yus, Joaquín
  • Ferrari, Begoña
  • Sánchez-Herencia, A. Javier
  • González Granados, Zoilo
[EN] It is well known that exposed surface area, nanoparticles connectivity and its consolidation level in a nanostructure are key points in the enhancement of the electrochemical performance in energy storage devices. The design and optimization of different electrodes with specific microarchitectures (based on the arrangement manipulation of NiO nanoplatelets, used as building blocks), has allowed distinguishing the effects of each microstructural contribution in their final electrochemical responses, overpassing thermal and mechanical mismatches between the semiconductor ceramic structure and the metallic collector. In all cases, the same electroactive material and the same coating technique were used, preventing the interference of secondary phenomena in the EIS studies, and allowing argue over the contribution of the microstructural features incorporated to the electrode (nature and shape of the collector, degree of sintering and consolidation of the ceramic microstructure, incorporation of non-noble metallic nanoparticles and the macro/meso/microposity effect) in the effective profiting of the Faradaic phenomena observed during their cycling. The modification of the Ni-based electrodes allows understanding how microstructural features infer the electron transport and the ion diffusion through the consolidated structure. The EIS analysis proves that the design of the porous hierarchical network of our semiconductors electrodes resulted in a good rate capability (with capacitance values of 1000 F g¿1 or 500 C g¿1), exhibiting a relaxation time constant (¿0 = 18 ms), while a slight increase of the charge-transfer resistance (Rct = 3.65¿) is negligible if the exposed surface is high enough to maintain a high ion transport. The inclusion of non-noble nanoparticles, such as Ni NPs, in the NiO semiconductor microstructure and the optimum deposited mass and sintering treatment create a metal-ceramic electrode that enhances both the charge transfer resistance (1.55 ¿) showing relaxation time in the range (¿0 = 11 ms) and maintaining an excellent capacitive behavior (750 F g¿1 or 375C g¿1) at quick charge/discharge rate., 2018/NMT-4411(Comunidad de Madrid, Spain) and MAT2015-70780-C4-1(MINECO/FEDER, Spain). J. Yus acknowledges the Comunidad de Madrid for the support from the Youth Employment Initiative,CAMPD17_ICV_002. Z. Gonzalez acknowledges the Postdoctoral Fellowship: IJCI-2016-28538 (MINECO, Spain)