Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Hydrogen uptake and diffusion kinetics in a quenched and tempered low carbon steel: experimental and numerical study

  • Peral, Luis Borja
  • Díaz Portugal, Andrés
  • Alegre Calderón, Jesús Manuel
  • Cuesta Segura, Isidoro Iván
To better understand hydrogen uptake kinetics, electrochemical permeation tests have been performed in a quenched and tempered low-alloy steel. Hydrogen uptake and transport has been studied with three different surface roughness, in four different solutions (1 M H2SO4, 1 M H2SO4+As2O3, 0.1 M NaOH and 3.5% NaCl) and two different hydrogen charging current densities (1 and 5 mA/cm2). A strong effect of the charging solution, current density and surface roughness has been demonstrated. In 1 M H2SO4 + As2O3 solution and 5 mA/cm2, hydrogen recombination on the surface of the samples is strongly reduced and interstitial diffusion prevails due to the trap saturation ( ). However, in 1 M H2SO4, 0.1 M NaOH and 3.5% NaCl, hydrogen transport is dominated by trapping and detrapping processes ( ). Permeation transients are numerically reproduced through Finite Element simulations and compared to the experimental results. The relationship between hydrogen diffusion kinetics at the microstructural level and surface effects is clearly established by a mapping strategy obtained from the wide range of experimental results, combined with a numerical approach., The authors would like to thank the Spanish Government for the financial support received to perform the research projects RTI2018-096070-B-C33 and PID2021-124768OB-C21. This work was supported by the Regional Government of Castilla y León (Junta de Castilla y León) and by the Ministry of Science and Innovation MICIN and the European Union Next Generation EU/PRTR (MR4W.P2 and MR5W.P3). L.B. Peral is also grateful for his Margarita Salas Postdoctoral contract (Ref.: MU-21-UP2021-030) funded by the University of Oviedo through the Next Generation European Union.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Influence of hydrogen on the hydraulic fracture behavior of a 42CrMo4 steel welds: Effect of the prior austenite grain size

  • Peral, Luis Borja
  • Díaz Portugal, Andrés
  • Arniella, V.
  • Belzunce, J.
  • Alegre Calderón, Jesús Manuel
  • Cuesta Segura, Isidoro Iván
The influence of hydrogen on the mechanical behavior of a quenched and tempered 42CrMo4 steel has been evaluated by means of high internal pressure fracture tests carried out on hydrogen precharged notched cylindrical specimens. The notched cylindrical specimens were precharged in a 1 M H2SO4 + 0.25 g/l As2O3 solution for 3 h with 1.2 mA/cm2. Hydraulic fracture tests were performed at different loading rates. Hydrogen embrittlement resistance increased with grain size refinement although the fine grained specimen had a higher hydrogen content than the coarse grained one. Fractographic analysis showed hydrogen enhanced decohesion fracture was less pronounced with decreasing grain size. Hydrogen embrittlement susceptibility is discussed in terms of the prior austenite grain size (PAGS) and the operative fracture mechanisms., The authors would like to thank the Spanish Government for the financial support received to perform the research projects TED2021-130413B-I00 and PID2021-124768OB-C21. This work was supported by the Regional Government of Castilla y León (Junta de Castilla y León) and by the Ministry of Science and Innovation MICIN and the European Union Next Generation EU/PRTR (MR5W.P3) and PRTR (MR4W.P2). L.B. Peral is grateful for his Margarita Salas Postdoctoral contract (Ref.: MU-21-UP2021-030) funded by the University of Oviedo through the Next Generation European Union.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Artículo científico (JournalArticle)

Methodology to predict mechanical properties of PA-12 lattice structures manufactured by powder bed fusion

  • Rodríguez Aparicio, Rubén
  • Alegre Calderón, Jesús Manuel
  • Verbeeten, Wilco M.H.
  • Lorenzo Bañuelos, Miriam
  • Cuesta Segura, Isidoro Iván
Topology optimization for weight reduction of additive manufacturing parts is commonly achieved throughout the creation of lattice structures, typically generated with beams of small size cross-section. In order to carry out accurate simulations of these lattice structures, knowing the mechanical behavior of pillars is required. In this paper, a methodology for determining the mechanical properties of small size pillars printed in PA-12 material, using polymer powder bed fusion (PBF) and in particular the Selective Laser Sintering (SLS) technology, is presented. The effect of defects originated during the manufacturing process on the macroscopic mechanical properties is studied and the mechanisms which influence these properties are analyzed. A methodology for the determination of these properties is proposed, based on a successive correction of the printed nominal diameters according to two approaches; one due to the outer skin of unmelted material and the other due to internal melting defects. Once the material properties are determined, as a function of the cross-section of the lattice pillars, the numerical simulation of lattice-type structures has been carried out and the degree of adjustment of the proposed methodology has been experimentally verified, obtaining good results. This validation provides a reliable method for the simulation of the macroscopic behavior of lattice-type structures with reduced sizes, taking into account the intrinsic defects generated during the printing process., The authors wish to acknowledge the funding received through the Junta de Castilla y León projects BU-002-P20 and INVESTUN/22/BU/0003 co-financed with FEDER funds, and the projects MR5W.P3 (C17. I01. P01. S21) and MR4W.P2 co-financed by JCyL and MICINN and the NextGenerationEU/PRTR funds.
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Contribución de congreso (ConferenceOutput)

Hydrogen Embrittlement of AISI 316L steel produced by Selective Laser Melting

  • Peral, Luis Borja
  • Díaz Portugal, Andrés
  • Ebrahimzadeh, P.
  • Fernández-Pariente, I.
  • Alegre Calderón, Jesús Manuel
  • Cuesta Segura, Isidoro Iván
Trabajo presentado en: Third European Conference on the Structural Integrity of Additively Manufactures Materials (ESIAM23), Selective laser melting (SLM) is one of the common methods of additive manufacturing and it can be employed to customize components with complex geometry expected to work in hydrogen atmospheres. However, more studies are still needed to characterize the behavior of printed mechanical components intended to work in contact with hydrogen. In this study, smooth and notched tensile samples were precharged in an acid solution with 8 mA/cm2 for 24h time. Hydrogen damage was more marked in the notched samples, especially at 0.005 mm/min, where fracture micromechanism changed from ductile in the absence of hydrogen to quasi-brittle in the presence of internal hydrogen. The role of the strain-induced martensite is also highlighted., The authors would like to thank the Spanish Government for the financial support received to perform the research projects PID2021-124768OB-C21 and TED2021-130413B-I00. This work was also supported by the Regional Government of Castilla y León (Junta de Castilla y León) and by the Ministry of Science and Innovation MICIN and the European Union Next Generation EU/PRTR (MR4W.P2 and MR5W.P3).