Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

HMR-based optical gas detection with CuO and ZnO coatings

  • Gallego Martínez, Elieser Ernesto
  • Ruiz Zamarreño, Carlos
  • Matías Maestro, Ignacio
This work presents the fabrication of hyperbolic mode resonance-based optical sensors by means of sputtered copper oxide (CuO) and zinc oxide (ZnO), and the study of their performance for gas sensing purposes. Two sensors were fabricated in a planar waveguide configuration with an intermediate gold thin film, and resonances were observed in the visible region of the electromagnetic spectrum. Both materials were analyzed with X-ray diffraction techniques, and their response was characterized by different concentrations of a group of gases comprised of nitric oxide, acetylene (C2H2), ethanol, carbon dioxide, and relative humidity. The best performance corresponds to the CuO sensor for C2H2 gas, presenting a sensitivity of 1.11 nm/parts per million (ppm) and a limit of detection of 12.6 ppb, with response and recovery times of 70 and 68 s, respectively. ZnO-based sensors allowed for a comprehensive study of ethanol in a range of thousands of ppm, while CuO-based sensors showed exceptional sensitivity for most gases in the range of a few ppm. All measurements were performed at room temperature., This work was supported in part by the Agencia Estatal de Investigación under Grant PID2019-106231RB-I00 and Grant PDC2023-145831-I00 and in part by the Institute Smart Cities of the Public University of Navarra Ph.D. Student Grants.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

A gas sensor based on the hyperbolic mode resonance by integrating hafnium dioxide thin-film in an optical structure

  • Correa Fernández, Ángel
  • Gallego Martínez, Elieser Ernesto
  • Ruiz Zamarreño, Carlos
  • Matías Maestro, Ignacio
Hafnium dioxide (HfO₂) is emerging as a transformative material in the field of optical gas sensing, offering a unique combination of high stability, exceptional dielectric properties, and strong surface adsorption capabilities. This work presents the integration of HfO₂ thin films—fabricated via Atomic Layer Deposition (ALD)—onto planar optical waveguide structures aimed to excite Hyperbolic Mode Resonances (HMR) with a remarkable refractive index (RI) sensitivity of 3347 nm/RIU in the range 1.3098–1.4311 RIU, among the top-performing devices in this type. The device was subjected to a diverse set of gaseous species, including oxygen, ethylene, nitric oxide, methanol, ethanol, and relative humidity. It revealed an outstanding performance for NO with a sensitivity of 1.89 nm/ppm and a limit of detection (LoD) as low as 76.2 ppb when operated at room temperature (23 º C). These results underscore the potential of HfO₂ as a novel sensing material that surpasses conventional metal oxides in both versatility and performance, opening new avenues for applications in environmental monitoring, industrial safety, and biomedical diagnostics, where low-cost, high-sensitivity, and roomtemperature operation are critical., This work was supported by the Agencia Estatal de Investigacion ´ research projects, Spain (Grant Nos. PID2022–137437OB-I00 and PDC2023–145831-I00), and by the Institute of Smart Cities of the Public University of Navarra Ph.D. student grants, Spain (Grant No. 401).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Resonance-based optical gas sensors

  • Gallego Martínez, Elieser Ernesto
  • Ruiz Zamarreño, Carlos
  • Matías Maestro, Ignacio
Gas sensors play a critical role in numerous human activities. Their necessity continues to grow across diverse fields as technological advancements drive demand for precision agriculture and bioengineering among other applications. Among existing sensor technologies, optical gas sensors stand out due to their ability to operate remotely in high-risk environments while remaining unaffected by electromagnetic interference. Resonance-based optical sensors offer targeted gas detection through the functionalization of their sensitive surfaces. This work focuses on reviewing the state of the art in resonance-based optical gas sensors (ROGSs), addressing their fundamental principles, recent advances in fabrication processes, waveguide designs, and materials employed both for resonance generation and as sensitive coatings. In addition, the review examines achieved sensitivity, emerging applications, and key developments in the field, including those efforts on improving ROGS performances by means of artificial intelligence techniques. The study encompasses optical sensors leveraging surface plasmon resonance, lossy mode resonance, and hyperbolic mode resonance¿the latter representing a notable breakthrough in recent years as a particular case of Bloch surface waves., This work was supported in part by the Agencia Estatal de Investigación under Grant PID2022-137437OB-I00 and Grant PDC2023-145831-I00, in part by the Institute Smart Cities and Public University of Navarra Ph.D. student grant, and in part by the International Mobility Scholarship of the Navarra Government.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Lossy mode resonance and hyperbolic mode resonance-based optical sensors by means of Y3Fe5O12 and SrTiO3 films deposition on planar substrates

  • Correa Fernández, Ángel
  • Gallego Martínez, Elieser Ernesto
  • Ruiz Zamarreño, Carlos
  • Matías Maestro, Ignacio
This letter describes the fabrication of sensor devices based on lossy mode resonance (LMR) and hyperbolic mode resonance (HMR) using for the first time as generating materials of the optical resonances both, yttrium iron garnet (Y3Fe5O12) and strontium titanate (SrTiO3) with a film thickness of 739.2 and 158.7 nm for Y3Fe5O12 (YIG) and SrTiO3, respectively. First-order resonances were observed at the visible region of the electromagnetic spectrum for both materials, LMR and HMR phenomena. RF sputtering deposition was used to fabricate metal oxide thin films on coverslips in a planar waveguide configuration, the Au metallic thin films were deposited by pulsed dc sputtering in a magnetron system from Moorfield. All devices were characterized under different surrounding medium refractive index. Sensitivities achieved values of 5862 and 5865 nm/RIU (refractive index unit) for HMR versions of Y3Fe5O12 and SrTiO3r, respectively. In addition, the response of the sensors to relative humidity and different ethanol concentrations was evaluated. The best results correspond to the Y3Fe3O3-based sensor, with a sensitivity of 0.2 nm/ppm and a limit of detection (LOD) of 183 ppm for ethanol, and 64 nm/%RH for RH, with an LOD of 2.23%RH, and because its resonance does not vanish unlike SrTiO3., This work was supported in part by the Agencia Estatal de Investigación research projects under Grant PID2019-106231RB-I00 and Grant PDC2023-145831-I00 and in part by the Institute Smart Cities of the Public University of Navarra Ph.D. student grants. Open access funding provided by Universidad Pública de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Photonic chip breath analyzer

  • Gallego Martínez, Elieser Ernesto
  • Matías Maestro, Ignacio
  • Ruiz Zamarreño, Carlos
This work introduces a novel single-package optical sensing device for multiple gas sensing, which is suitable for breath analysis applications. It is fabricated on a coverslip substrate via a sputtering technique and uses a planar waveguide configuration with lateral incidence of light. It features three sequentially ordered strips of different materials, which serve to increase the multivariate nature of the response of the device to different gases. For the proof-of-concept, the selected materials are indium tin oxide (ITO), tin oxide (SnO2), and chromium oxide III (Cr2O3), while the selected gases are nitric oxide (NO), acetylene (C2H2), and ammonia (NH3). The sensing mechanism is based on the hyperbolic mode resonance (HMR) effect, with the first-order resonance obtained for each strip located in the near infrared region. The multivariate response of the resonances and the correlation with the concentration of each gas allow training a machine learning (ML) model based on a nonlinear autoregressive neural network, enabling the accurate prediction of the concentration of each gas. The obtained limit of detection for all the gases was in the order of a few parts per billion. This innovative approach coined as the multivariate optical resonances spectroscopy demonstrates the potential of HMR-based optical sensors in combination with ML techniques for ultra-sensitive multi-gas detection applications using a single device., This work was supported by the Agencia Estatal de Investigación research projects, Spain (Grant Nos. PID2019-106231RB-I00 and PDC2023-145831-I00), and by the Institute Smart Cities of the Public University of Navarra Ph.D. student grants, Spain (Grant No. 401).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Hyperbolic mode resonance-based acetone optical sensors powered by ensemble learning

  • Gallego Martínez, Elieser Ernesto
  • Ruiz Zamarreño, Carlos
  • Meurs, Joris
  • Cristescu, Simona M.
  • Matías Maestro, Ignacio
The current work describes and compares the performance of hyperbolic mode resonance (HMR)-based sensors for the detection of acetone at parts per billion (ppb) concentrations using ensemble machine learning (EML) techniques. A pair of HMR based-sensors with resonances located in the visible (VIS) and mid infrared (MIR) regions were obtained in order to train a set of ensemble machine learning models. The response of the detection system formed by both devices in the VIS and MIR regions, with the help of the EML system, allowed the limit of detection (LoD) of the sensors to be reduced by an order of magnitude. It is the first time that HMR-based sensors are shown in practical applications, at the same time that their performance is improved using EML techniques. This opens new avenues for the use of this type of HMR-based sensors for the detection of other substances, in addition to improving the performance of any optoelectronic sensor using EML techniques., This work was supported by Agencia Estatal de Investigación (PID2022-137437OB-I00 and PDC2023-145831-I00), Institute Smart Cities and Public University of Navarra Ph.D. student grant, International Mobility Scholarship of the Navarra Government, and the Radboud University.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

A systemic model for lossy mode resonances (LMRs)

  • Imas González, José Javier
  • Del Villar, Ignacio
  • Halir, Robert
  • Wangüemert-Pérez, J. Gonzalo
  • Ortega-Moñux, Alejandro
  • Matías Maestro, Ignacio
  • Molina-Fernández, Íñigo
Lossy mode resonances (LMRs) have been widely employed for the development of sensors in the last years. However, the theoretical frameworks for LMRs are scarce and difficult to systematize, hampering the development of this technology. In this work, we propose a new systemic model for assessing LMRs in arbitrary waveguide configurations, based solely on modal analysis of the unperturbed waveguide and the waveguide with a thin film optimized for LMR generation. The model is first developed for a generic waveguide, and leveraged to design, for the first time, LMRs in a silicon nitride photonic wire waveguide. It is furthermore demonstrated that the model only requires a few modes to reliably describe LMRs in D-shaped fibers, reducing the computational cost of simulating them. Therefore, the suggested model is valid for both high and low contrast waveguides, and it is considered it provides new insights about LMRs, which will help in the design of new LMR-based devices and its extension to novel platforms., This work was supported by Agencia Estatal de Investigación (grant JDC2022-048216-I, project PDC2023-145831-I00, and project TED2021-130400B-I00/AEI/ https://doi.org/10.13039/501100011033/European Union NextGeneration EU/PRTR).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Novel sputtered metal oxides (SnO2:F, HfO2, WO3) for high-sensitivity HMR-based optical refractometers

  • Correa Fernández, Ángel
  • Gallego Martínez, Elieser Ernesto
  • Ruiz Zamarreño, Carlos
  • Matías Maestro, Ignacio
Hyperbolic mode resonances (HMR)-based devices, presented as the natural successors of lossy mode resonance-based devices, can provide deep and stable resonances with remarkable sensitivity. However, they are still in its infancy with ample room for the exploration of novel materials that enable the generation of HMR. This work explores the utilization of fluorinated tin oxide (SnO2:F), hafnium dioxide (HfO2), and tungsten trioxide (WO3) as external coatings for HMR generation using a planar waveguide configuration (24 mm x 32 mm coverslips). Basic HMR structure consisted of a combination of DC and RF sputtered coatings of an intermediate Au layer and a metal oxide external layer, respectively. The sensors¿ spectral responses were measured over a refractive index (RI) range spanning from air (¿1.0) to 1.45, covering relevant analytes in gas and liquid sensing. HMR sensors exhibited distinct resonance features that shift systematically with increasing RI, enabling accurate label-free refractometry. The obtained sensitivity, figure of merit, and linearity are compared across the three devices, highlighting the influence of the hyperbolic metamaterial design on the sensing performance. Obtained results demonstrate that HMR-based sensors can provide compact and versatile platforms for RI detection, with enormous potential for integration into lab-on-a-chip systems., This work was supported in part by Agencia Estatal de Investigación under Grant PID2019-106231RB-I00 and Grant PDC2023-145831-I00 research projects and in part by the Institute Smart Cities of the Public University of Navarra Ph.D. student grants.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Printed optical waveguide temperature sensor with rhodamine-doped core

  • Dávila Galiana, Rebeca Beatriz
  • Matías Maestro, Ignacio
  • Zabala, Silvia
  • Socorro Leránoz, Abián Bentor
  • Rivero Fuente, Pedro J.
  • Corres Sanz, Jesús María
This letter demonstrates the fabrication of a temperature optical sensor by printing the corresponding sensitive optical waveguide directly onto a flexible flat substrate. The printed waveguide was carried out using a coaxial needle and an electrohydrodynamic (EHD) machine. The fluorescent organic compound, rhodamine B, was used for doping the core of the printed waveguide as temperature sensible dye. The optical sensitive waveguide manufactured is compact, ensuring coupling with the input and output optical fibers. The response of the printed optical sensor was evaluated to temperature variations by measurement of both, the peak intensity and the wavelength of the fluorescence spectra. The experimental characteristic and sensitivity of the sensor were obtained., This work was supported in part by the Gobierno de Navarra under Grant PC058-059 EleSpray and in part by the Agencia Estatal de Investigación under Grant PID2022-137437OB-I00 and Grant PDC2023-145831-I00.