Pasar al contenido principal

BIOCOMPATIBILIDAD DE NUEVAS ALEACIONES PULVIMETALURGICAS DE TITANIO OBTENIDAS POR TECNOLOGIAS AVANZADAS

RTI2018-097810-B-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 22
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development of Ti-Zr alloys by powder metallurgy for biomedical applications

  • Amigó-Mata, Angèlica
  • Haro Rodríguez, Monserrat Vicenta
  • Vicente-Escuder, Ángel|||0000-0001-8425-3424
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Commercial pure titanium offers excellent biocompatibility, but its properties are poor for some biomedical applications where both mechanical properties and biocompatibility are required. The study attempts to evaluate the developement ofTi¿Zr alloys using conventional powder metallurgical techniques by mixing elemental powder (BE) or mechanical mixing (MA) as a function of the zirconium content (6, 15 and 20 wt-%). Sintering was performed at 1523 K after compaction at 700 MPa for BE powders and 900 MPa for MA powders. Sintered parts were tested to obtain maximum flexural strength. Samples were characterised microstructurally by X-ray diffraction to study the phases. Optical microscopy (OM) and scanning electron microscopy (SEM) were performed to study the phases, porosity, grain size. Flexural strength to Ti CP was greater, but slightly diminished with increasing Zr content. However, the elastic modulus increased slightly compared to Ti. The results obtained show that it is possible to make these alloys by powder metallurgy., This work was supported by the Ministerio Español de Ciencia e Innovación with grant [RTI2018-097810-B-I00]; the Generalitat Valenciana with grant [PROMETEO2016/ 040]; the EU for the funding received through FEDER.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of Electrochemical and Biological Characteristics of As-Cast Ti-Nb-Zr-Ta System Based on Its Microstructure

  • Correa Rossi, Mariana
  • Navarro, Beatriz
  • Milian Medina, Lara
  • Vicente-Escuder, Ángel|||0000-0001-8425-3424
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] The quaternary Ti-Nb-Zr-Ta (TNZT) alloy was successfully cast-fabricated with the objective to be used in the medical field. Samples' microstructure was compared to CP-Ti and Ti-6Al-4V (control samples) and related to corrosion, ion release and biological properties. As-cast TNZT was formed with large grain sizes (285 m) compared to the ultrafine grain sizes of CP-Ti (11 m) and the + ultrafine grain sizes of 1.45 m and 0.74 m. Hardness and flexural elastic moduli (94 HV and 43 GPa) came close to the biological structures, such as dentin and enamel values. The ion release mechanism of as-cast TNZT was significantly lesser than CP-Ti and Ti-6Al-4V, which can be related to the difference in samples¿ grain sizes and chemical compositions. However, the corrosion rate was higher than for the control samples; this way offers corrosion properties inferior with respect to the properties obtained in the reference materials. Biological assays demonstrated that the two-cell (hDPSCs and MG-63) lineage studied presented good adhesion and capability to differentiate in bone cells on the as-cast TNZT surface, and no cytotoxicity effects were found. Details and reasons based on samples¿ microstructure are discussed., The authors thank the Spanish Ministerio de Economia y Competitividad for Research Project RTI2018-097810-B-I00 and the European Commission for FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effects of density current on mechanical and electrochemical properties of B Ti-35Nb-6Mo alloy manufactured through electric resistance sintering

  • De Santi-Gouvea, Eber
  • Correa Rossi, Mariana
  • Afonso, Conrado Ramos Moreira
  • Calero Martínez, José Antonio
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Ti-35Nb-6Mo alloys were fabricated using the Electrical Resistance Sintering (ERS) technique. Powders were produced by mechanical alloying and then sintered under electrical current densities: 10,11,12 and 13 kA. The microstructural, mechanical, and electrochemical properties of the alloys were evaluated. The effects of oxygen and nitrogen as interstitial elements were analyzed, revealing no significant difference in oxygen content among the alloys; however, the nitrogen content was found to be minimal according to the relationship: 0.06 (N)-12kA; 0.12(N)-10 and 11 kA. The samples were predominantly composed of the ß phase. Grain size increased with rising current density, and the elastic modulus (E) also showed an increase with higher current densities (13 kA>90 GPa and for 10 kA>110 GPa). The best results for tensile strength, Vickers microhardness (HV), and cantilever resistance were achieved at current densities of 11 and 12 kA. The best mechanical results were approximately: ¿600 MPa; 420HV; ¿¿600 MPa. Nanoindentation measurements revealed that the samples sintered at 11 and 12 kA exhibited greater variability in both E and HV across the samples, while 10 and 13 kA showed to be more homogeneous across the sample. The greatest corrosion properties were found for 12 kA condition alloy with: OCP: ¿ 0.11 V; Ecorr: ¿ 0.18 V; Icorr: 1.04 × 10¿ 7A and Rp: 3.5 × 105¿. This alloy sintered at 12 kA showing the highest polarization resistance, superior corrosion resistance, and the lowest corrosion current compared to the other conditions., The authors are very grateful to FAPESP to post-doctorate grant, #2021/03865-9, #2023/04654-7 and Projeto Tematico 2018/18293- 8. Funding from the Spanish Ministerio de Ciencia, Innovacion y Universidades with project RTI2018-097810-B-I00, and the European Commission via European Regional Development Fund (FEDER).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Electrochemical corrosion behavior of Ti-35Nb-7Zr-5Ta powder metallurgic alloys after Hot Isostatic Process in fluorinated artificial saliva

  • Lario-Femenía, Joan|||0000-0003-4843-3334
  • Vicente-Escuder, Ángel|||0000-0001-8425-3424
  • Segovia-López, Francisco|||0000-0002-4143-5751
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] The present study aimed to evaluate the effect of the Hot Isostatic Process (HIP) process on the microstructure, phase stability and corrosion resistance of Ti35Nb7Zr5Ta powder metallurgy alloys. The corrosion resistance of titanium alloys was tested by analyzing the open circuit potential (OCP), potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and ion release in physiological Fusayama solution. Polarization curves showed that the Tie35Nbe7Zre2Ta alloy presented good passivation behavior thanks to its low current densities (<10E-8 A/cm2) and high polarization resistance. The interpretation of an equivalent electric circuit (EEC) demonstrated the formation of a very stable oxide film on the alloy, as indicated by good capacitive behavior, high impedance values (>10E+06 ohmios·cm2) at low frequencies and phase angles close to -90º according to the EIS results with less ion release., This research was funded by Spanish Ministry of Economy and Competitiveness, Research Project 553 Project RTI2018-097810-B-I00, and the European Climate Foundation funds to purchase equipment for research purposes and the Microscopy Service at the Valencia Polytechnic University.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Powder Metallurgy: A New Path for Advanced Titanium Alloys in the EU Medical Device Supply Chain

  • Lario-Femenía, Joan|||0000-0003-4843-3334
  • Poler, R.|||0000-0003-4475-6371
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] New beta titanium alloys are expected to present high mechanical properties with good biocompatibility to meet the demands of next-generation implants. This paper presents an overview of the current European Union titanium supply chain and several metallurgical processes and technologies required to develop the beta-based titanium alloy industry. The thermomechanical process involves manufacturing advanced beta titanium alloys, where cost reduction must involve every step of the entire process. When synergistically combined, powder metallurgical technology, together with a set metallurgical process, can produce advanced materials for the biomedical industry with a low-cost ratio compared to current melting and forging manufacturing routes. We propose a new strategy to increase the role of advanced titanium alloys in the European Union medical device supply chain., The authors thank the Spanish Ministerio de Ciencia, Innovacion y Universidades for Research Project RTI2018-097810-B-I00, the European Commission for FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Assessment of b stabilizers additions on microstructure and properties of as-cast beta Ti-Nb based alloys

  • Formenton dos Santos, Rafael
  • Correa Rossi, Mariana
  • Vidilli, André Luiz
  • Afonso, Conrado Ramos Moreira
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] The novelty of the present work lies in elucidating the correlation of Moeq with mechanical and surface parameters. The Ti-15Nb (TN-15), Ti-40Nb (TN-40), Ti-33Nb-33Zr (TNZ-33), Ti-40Nb-40Zr (TNZ40) and Ti-35Nb-7Zr-5Ta (TNZT) alloys were obtained by casting. The alloys were formed by beta-Ti grains with a micrometric morphology, except the as-cast TN-15 alloy formed by alpha + beta. Adding Nb and Zr influenced the lattice parameters of phase beta, as well as the crystal structure. Grain size (GS) decreased by adding Nb and Zr following this relation: TN-40 > TNZ-33 > TNZT > TNZ40. The roughness decreased with rising Nb and Zr contents being in the range of 1.3-3 mm, and it was possible to correlate it with the Moeq. The contact angle and free energy surface values were inversely proportional, and the as-cast TNZ40 alloy with smaller GS was less wettable (60) than TN40 (GS: 1423 mm). The mechanical properties decreased to Moeq of 14.9 wt% then their significantly went above this value, except for the as-cast TN-15 alloy (E: 65 GPa, microhardness: 264 HV) formed mainly by a hardener phase alpha. Both elastic modulus and microhardness showed the same tendency as the Moeq values and the cell parameter of phase beta (ab). The oxygen content was all in accordance with ASTM E1409-13 for applications as metallic biomaterials being in the range of 0.044-0.195 wt%., This study was financed partly by the Coordenacao de Aperfeicoamento de Pessoal de Nivel Superior of Brazil (CAPES), Finance Code 001, and Ph.D. grant # 88887.371759/2019-00 (R.F.M.S.). The authors wish to thank Brazilian agencies: CNPq Universal Project #422015/2018-0 (C.R.M.A.); FAPESP (Sao Paulo Research Foundation) for financial support through "Projeto Tematico" # 2018/18293-8, post doc Grant # 2021/03865-9 (M.C.R.), PhD Scholarship 2021/11537-1 (A.L.V) and funding from Spanish Ministerio de Ciencia, innovacion y Universidades with project RTI2018-097810-B-I00, and the European Commission via FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Properties and prospects for biomedical application of new Ti-Nb-Sn alloys obtained by electrical resistance sintering

  • Vinogradova, Maria
  • Klyatskina, Elizaveta
  • Amigó, Vicente|||0000-0002-2107-0273
  • Segovia-López, Francisco|||0000-0002-4143-5751
[EN] Active research of new ß titanium alloy compositions is underway. At the same time, new ways of alloy preparation by powder metallurgy methods are being investigated. In this work Ti-35Nb-XSn alloy (X = 0, 4, 6 wt%) were obtained via electrical resistance sintering (ERS) at current intensities of 11 and 12 kA respectively. The influence of alloying element content and process conditions on the alloys structure and properties in the context of biomedical application were investigated., This work was supported by the Ministerio Espanol de Ciencia, Innovacion y Universidades [Grant RTI2018-097810-B-I00], the EU through FEDER, and AMES Group (Spain).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Relation between Mechanical Milling Parameters in Phase Transformation and Oxygen Content in Ti-Nb-Mo Powders for Posterior Sintering

  • De Santi-Gouvea, Eber
  • Correa Rossi, Mariana
  • Afonso, Conrado Ramos Moreira
  • Vicente-Escuder, Ángel|||0000-0001-8425-3424
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] The influence of open vessels during milling for 12, 24, 40 and 60 h on microstructure homogeneity and oxygen content effect in the beta Ti-Nb-Mo system microstructure were studied. The beta phase increased with longer milling times and the strain hardening on particles was verified at 60 h when agglomeration was greater and was also noticed after 40 h in the continuous mode. Oxygen content dropped slightly until 40 h and increased after 60 h, a result linked with the observed hardening. For 40 h in the continuous mode, the oxygen content was noted near 12 h, 24 h and 40 h with high hardness values. For the sintered parts, the alpha phase and oxygen content significantly increased in all samples. Microhardness-sintered samples decreased compared to sample powders due to grain growth during the sintering. Bending strength was higher at 60 h with more oxygen and alpha phase content. After 40 h in the continuous mode, more suitable mechanical properties were reached because hardness and bending strength were closer to bone tissue, which was associated with strain hardening and a small crystallite size., The authors thank the Spanish Ministerio de Economia y Competitividad for Research Project RTI2018-097810-B-I00, the European Commission for FEDER funds and the Fundacao de Amparo a Pesquisa do Estado de Sao Paulo [grant: 2021/03865-9].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluation of the influence of low Mg content on the mechanical and microstructural properties of beta titanium alloy

  • Correa Rossi, Mariana
  • Leal Bayerlein, Daniel
  • De Santi-Gouvea, Eber
  • Haro Rodríguez, Monserrat Vicenta
  • Vicente-Escuder, Ángel|||0000-0001-8425-3424
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] It was investigated in order to better understand the relationship between the low presence of Mg in the TieNbeSn alloy in its mechanical and microstructural properties by the powder metallurgy technique for biomedical application. The blended powders with the nominal composition of Tie34Nbe6Sn were obtained by milling at 200 rpm/40 min, compacted at 200 MPa. The sintering were carried out at 900 C/2 h and at 1110 C/2 h, followed by furnace cooling. The particle size was characterized by the dynamic image analyzer (DIA). The phases quantification and their microstructure were characterized by an X-ray diffractometer (XRD) and a scanning electron microscope (SEM). The porosity was characterized by the Archimedes method and also bi-dimensionally by the Image J software. The mechanical tests were performed by the impulse excitation (Sonelastic ®) technique, in order to evaluate the elastic modulus (E) of the sintered materials and the hardness and resistance by the Rockwell method. The results indicated that the sintering at 1100 C in the materials with Mg, still had particles of Nb not diffused. The microstructure was basically formed by two phases with the presence of Nb non-diffused in all conditions except at 1100 C in the system without Mg. The b phase % for systems without and with Mg at 900 C was approximately 80% and 65%. At 1100 C, 76% and 78%. The E and hardness were 31 GPa and 226 MPa at 900 C; 49 GPa and 344 MPa at 1100 C for materials with Mg. The O and N content increased approximately 1.3 times when adding Mg powder., This work was supported by the Fundacao de Amparo a Pesquisa do Estado de Sao Paulo [grant: 2019/24237-6], by the Ministerio Espanol de Ciencia, Innovacion y Universidades with Grant RTI2018-097810-B-I00 and the Instituto de Pesquisas Tecnologicas do Estado de Sao Paulo (IPT-SP), in the development of materials, whom the authors thank
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microstructural, mechanical, electrochemical, and biological studies of an electron beam melted Ti-6Al-4V alloy

  • Romero-Resendiz, L.
  • Rossi, M.C.
  • Álvarez, A.
  • García-García, A.
  • Milián, L.
  • Tormo-Mas, M.A.
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] This work studied the feasibility of an electron beam melting (EBM) Ti-6Al-4V alloy as a biomaterial for implants. Comparisons were made with a wrought forged Ti-6Al-4V alloy. The objective of this work was a detailed escription of the microstructural and surface roughness effects on mechanical, electrochemical, and in-vivo biological performances. The EBMed condition showed higher mechanical properties, as well as higher electrochemical and ion release rates. These results were mainly influenced by the lamellar grain morphology and complex crystallographic texture of the EBMed alloy compared to the forged one. The higher area average roughness of the EBMed condition boosted the adhesion, proliferation, and biofilm formation of osteosarcoma (MG63), Staphylococcus epidermidis (S. epidermidis), and Staphylococcus aureus (S. aureus). The mechanical, ion release, corrosion, and in-vivo biological results in both studied conditions met the requirements for orthopedic and dental biomaterials. However, the forged condition is more recommended for patients with clinic stories related to S. epidermidis and S. aureus illnesses., This work was supported by Ministerio de Economía y Competitividad from Spain under the RTI2018-097810-B-I00 grant number and by the European Commission through the European Regional Development Fund (ERDF). L. R-R. acknowledges CONACYT (Mexico) for the scholarship granted under the number 465504. Valuable technical support provided by Rafael Ibarra-Contreras is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

The Effect of Ti/Ta Ratio and Processing Routes on the Hardness and Elastic Modulus of Porous TiNbZrTa Alloys

  • González-Guillén, Celia
  • Al-Hawajreh-Kamel, Ghaith
  • Degalez-Duran, Eduardo
  • Naeem, Muhammad
  • Romero-Resendiz, Liliana
  • González, Gonzalo
  • Klyatskina, Elizaveta
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] TiNbZrTa alloys are promising for multidisciplinary applications, such as refractory and biomedical purposes, due to their high thermal stability and non-toxicity. Hardness and elastic modulus are among the key features for their adequate industrial applications. The influence of porosity and Ti/Ta ratio were investigated on TiNbZrTa alloys produced by three different processing routes, i.e., (i) blend element and posterior press and sintering (BE + P&S); (ii) mechanical alloying with press and sintering (MA + P&S); and (iii) arc melting and casting. Porosity decreased in the following order: casting < MA + P&S < BE + P&S. The total porosity of alloys increased with increasing Ta contents, i.e., by lowering the Ti/Ta ratio. However, the Ti/Ta ratio did not considerably affect the bonding energy or the elastic modulus. Hardness was increased significantly in dense alloys compared to porous ones. However, porosity and Ti/Ta ratio did not show a clear trend in hardness among the porous alloys., This research was funded by the Spanish Ministerio de Ciencia, Innovación y Universidades with grant number RTI2018-097810-B-I00 ; the European Commission via the European Regional Development Fund (FEDER); the UNAM-DGAPA-PASPA program (sabbatical year of G.G.); the Programa de Apoyo a Proyectos de Investigacion e Innovacion Tecnologica (PAPIIT)-UNAM under grant number IN102321; the Programa de Apoyo a la Investigación y el Posgrado (PAIP) of the Facultad de Química of Universidad Nacional Autónoma de México under grant number PAIP50009223; and the (PAPIIT)-UNAM under grant number IA102724.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of alloying elements on laser surface modification of powder metallurgy to improve surface mechanical properties of beta titanium alloys for biomedical application

  • Rossi, M. C.
  • Amado, J. M.
  • Tobar, M. J.
  • Yáñez, A.
  • Vicente-Escuder, Ángel|||0000-0001-8425-3424
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Beta-type titanium alloy surfaces (Tie35Nbe10Ta (TNT) and Tie30Nbe4Sn (TNS)) were modified by laser using a power of 1000Wand speed of 6.7 mm/s (Condition A) and a power of 1500 W with speed of 10 mm/s (Condition B). Increasing laser conditions, the thickness of the molten layer was also increased. The initial equiaxed grains changes to quite elongated grains shape. The surfaces were structured under alfa" martensite, alfa and matrix beta. The beta phase content decreased slightly and the alfa" phase increased for both alloys increasing the laser conditions. The condition A increased the elastic modulus (E) and decreased the hardness while condition B did not affect the mechanical properties surface for the TNT system compared to base metal (BM). In TNS system the laser condition A decreased the E and increased the hardness while increasing the laser parameters (Condition B) both E and hardness decreased compared to BM. The laser surface treatment was influenced by the levels of alloying elements present promoting most significant changes in the microstructure and mechanical properties in the TNS system., This work was supported by the Ministerio Espan~ol de Ciencia, Innovaci?on y Universidades, Spain with Grant RTI2018-097810-B-I00, RTI2018-096472-B-I00 and the European Union (EU) through Fondo Europeo de Desarrollo Regional (FEDER) , Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Mechanical, Corrosion, and Ion Release Studies of Ti-34Nb-6Sn Alloy with Comparable to the Bone Elastic Modulus by Powder Metallurgy Method

  • Correa Rossi, Mariana
  • Romero-Resendiz, Liliana
  • Leal Bayerlein, Daniel
  • Garcia Alves, Ana Liz
  • Segovia-López, Francisco|||0000-0002-4143-5751
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] The development of a Ti-34Nb-6Sn alloy by the powder metallurgy method, employing two different compaction conditions, A (100 MPa) and B (200 MPa), was carried out. To evaluate the feasibility of the Ti-34Nb-6Sn alloy as an implant biomaterial, microstructural and mechanical characterizations, as well as corrosion susceptibility and ion release tests, were performed. Results indicated microstructures dominated by the presence of -Ti phase and a lower percentage of -Ti and Nb phases. The porosity percentage decreased when the compaction pressure increased. Both conditions presented a good match between the elastic moduli of the alloy (14.0 to 18.8 GPa) and that reported for the bone tissue. The Ti, Nb and Sn ions released for both compaction conditions were within the acceptable ranges for the human body. Condition B showed higher corrosion resistance in comparison with condition A. Based on the obtained results, the produced porous Ti-34Nb-6Sn alloys are feasible materials for orthopedic implant applications., This research was funded by the Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP) (grant: 2017/13876-2; 2019/24237-6), by the Ministerio Español de Ciencia, Innovación y Universidades, with Grant RTI2018-097810-B-I00, and by the Instituto de Pesquisas Tecnológicas do Estado de São Paulo (IPT-SP). L.R.-R. acknowledges CONACyT for the PhD scholarship with number 465504.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Nanoindentation and orientation imaging analysis of high entropy Ti-Nb-Zr-Ta-Mo alloys exhibiting dendrite microstructure

  • Aranda, V. A.
  • Barba-Pingarrón, A.
  • Figueroa, I.A.
  • González, G.
  • Klyatskina, Elizaveta
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Refractory high entropy alloys (RHEAs), particularly Ti¿Nb¿Zr¿Ta¿Mo, are promising materials because of their high mechanical properties at elevated temperatures. Although a unique solid-solution phase characterizes these materials, the dendrite structure exhibits a clear element segregation when prepared by liquid route, leading to a different composition between dendrite and interdendrite. This study investigates the local mechanical properties of dendritic and interdendritic regions and the effect of adding Mo on the segregation and hardness. Two alloy compositions, i.e., Ti25 Nb25 Zr25 Ta25 and Ti30 Nb20 Zr20Ta20 Mo10 (at.%), were produced by copper mold suction casting. Characterization was carried out by XRD, EBSD, and nanoindentation mapping. It was observed that Mo reduces the lattice difference between the dendrite and interdendrite; both play different roles during plastic deformation, as interdendrites accumulate higher dislocation density. The alloys did not show any strain hardening after the compression test. Finally, Mo plays a key role in increasing the mechanical properties by solid solution hardening., This work was supported by the Programa de Apoyo a Proyectos de Investigacion e Innovacion Tecnologica (PAPIIT) -UNAM under grant number IN110124 and for the Spanish Ministerio de Ciencia, Innovacion y Universidades with project RTI2028-097810-B-100, and the European Commission via FEDER.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evolution of the Microstructure and Mechanical Properties of a Ti35Nb2Sn Alloy Post-Processed by Hot Isostatic Pressing for Biomedical Applications

  • Lario-Femenía, Joan|||0000-0003-4843-3334
  • Vicente-Escuder, Ángel|||0000-0001-8425-3424
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] The HIP post-processing step is required for developing next generation of advanced powder metallurgy titanium alloys for orthopedic and dental applications. The influence of the hot isostatic pressing (HIP) post-processing step on structural and phase changes, porosity healing, and mechanical strength in a powder metallurgy Ti35Nb2Sn alloy was studied. Powders were pressed at room temperature at 750 MPa, and then sintered at 1350 °C in a vacuum for 3 h. The standard HIP process at 1200 °C and 150 MPa for 3 h was performed to study its effect on a Ti35Nb2Sn powder metallurgy alloy. The influence of the HIP process and cold rate on the density, microstructure, quantity of interstitial elements, mechanical strength, and Young¿s modulus was investigated. HIP post-processing for 2 h at 1200 °C and 150 MPa led to greater porosity reduction and a marked retention of the ß phase at room temperature. The slow cooling rate during the HIP process affected phase stability, with a large amount of ¿¿-phase precipitate, which decreased the titanium alloy¿s yield strength., This research was funded by Spanish Ministry of Economy and Competitiveness, Research Project 553 Project RTI2018-097810-B-I00, and the European Commission via FEDER funds to purchase equipment for research purposes and the Microscopy Service at the Valencia Polytechnic University.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Corrosion behaviour of Ti-Nb-Ag powder metallurgical alloys and their potential application as biomaterials

  • Klyatskina, Elizaveta
  • Segovia-López, Francisco|||0000-0002-4143-5751
  • Amigó, Vicente|||0000-0002-2107-0273
  • Vinogradova, Maria
  • Bermúdez Castañeda, Ángela
[EN] One of the most important characteristics of medical devices are materials and their properties. Specially, the corrosion resistance, which is considered very relevant. Furthermore, several alloys have been developed by powder metallurgic processes to control the composition. Accordingly, the propose of this work is to study the influence in Ti-35Nb alloys of the addition of silver (X=0, 2, 4 and 6 wt%) respect to the mechanical properties and the corrosion performance, in solutions similar to human body fluids. Corrosion resistance has been analyzed by ion release as well as polarization in artificial saliva Fusayama [1] and Hartmann solution as electrolytes. Likewise, the microstructural characteristics and mechanical properties have been studied. The results obtained demonstrate the viability of these Ti35NbXAg alloys for their possible use as biomedical implants., This work was supported by the Ministerio Español de Ciencia, Innovación y Universidades with Grant RTI2018-097810- B-I00, and the EU through FEDER.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development of Ti-In alloys by powder metallurgy for application as dental biomaterial

  • Romero-Resendiz, L.
  • Gómez-Sáez, P.
  • Vicente-Escuder, Ángel|||0000-0001-8425-3424
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Substantial progress has been made in Ti alloys¿ properties and chemical composition. However, the effect of porosity and indium content on biocompatibility and corrosion behavior has not been sufficiently studied. Indium (In) is a promising nontoxic element that can replace other toxic elements, while porosity is associated with a good biological response. The purpose of this paper is to evaluate the achievability of three Ti-In alloys with 2.5, 5, and 10 wt.% Indium by powder metallurgy methods as dental prostheses. The findings of the present work showed that In acted as a grain refiner, and allowed us to obtain an 11.2-fold reduction for the Ti-10In sample than for the Ti-2.5In alloy. The total porosity of the TieIn alloys decreased according to In content, however, grain size and In content showed a greater effect on the mechanical behavior in comparison with the effect of porosity, probably because of the low porosity percentage. All the mechanical values fell within the ranges accepted in the literature for dental implant applications. The Ti3+ and In3+ ion releases were below the toxic concentrations for the human body, with a maximum of 0.43 and 0.016 mg cm-2 h-1, respectively. Corrosion sensitivity decreased with In addition due to its surface protective effect on the Ti-matrix. These results proved that utilizing powder metallurgy methods, TieIn alloys are feasible candidates for dental prosthesis. Of the three prepared TieIn alloys, the Tie10In alloy properties made it the most appropriate TieIn alloy to be used as a dental implant., This work was supported by the Ministerio Espanol de Ciencia, Innovacion y Universidades, Spain with Grant RTI2018097810-B-I00, and the European Union (EU) through Fondo Europeo de Desarrollo Regional (FEDER), Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Electrochemical corrosion behavior and mechanical properties of Ti-Ag biomedical alloys obtained by two powder metallurgy processing routes

  • Zambrano Carrullo, J. C.
  • Dalmau-Borrás, Alba
  • Pereira Falcón, C.
  • Amigó, Vicente|||0000-0002-2107-0273
  • Navarro-Laboulais, J.|||0000-0001-6347-5407
[EN] Titanium is frequently used as a biomaterial and the importance of Ti-Ag alloys has increased thanks to the antibacterial behavior of silver. In this study, Ti-Ag alloys (5, 10 and 15 wt% Ag) were obtained by two different powder metallurgy routes: blended elemental (BE) and mechanical alloying (MA). The influence of the powder mixture methodology on both microstructure and electrochemical behavior was analyzed. Powders were com-pacted at 600 and 900 MPa, respectively, and sintered at high vacuum for 3 h at 950 degrees C. The obtained Ti-Ag alloys were microstructurally characterized by Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray Spectroscopy (EDS) and X-Ray Diffraction (XRD), and mechanically tested by hardness and bending tests. Electrochemical tests were run using a three-electrode cell in an artificial Fusayama saliva solution. Open-Circuit Potential (OCP), polarization curves, potentiostatic tests and Electrochemical Impedance Spectroscopy (EIS) techniques were employed to evaluate the corrosion resistance of the studied Ti-Ag alloys. The initial characteristics of powders before sintering and after blend/alloying modified the electrochemical behavior of the Ti-Ag-sintered alloys and were determined. The samples obtained with the BE powders better resisted corrosion than the MA samples, and this behavior was directly related to the quantity and distribution of intermetallic Ti2Ag. A large quantity of intermetallics present on both the edge and inside grains reduced the corrosion resistance of TiAg alloys., The authors wish to thank the Generalitat Valenciana for support through PROMETEO 2016/040. Alba Dalmau acknowledges the Generalitat Valenciana for her grant (APOSTD/2017/051), the European Commission via FEDER funds to purchase equipment for research purposes in ISIRYM and the Ministry of Science, Innovation and Universities for the project RTI2018-097810-B-I00. Finally, they thank the Microscopy Service at Universitat Politecnica de Valencia in Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development of a porous Ti-35Nb-5In alloy with low elastic modulus for biomedical implants

  • Romero-Resendiz, L.
  • Rossi, M.C.
  • Seguí-Esquembre, C.
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] A new porous Tie35Nbe5In alloy was designed to join the advantages of low elastic modulus and non-toxicity, which are critical factors for biomedical implants. The Tie35Nb e5In alloy was produced by powder metallurgy, and its feasibility as implant material was evaluated through mechanical properties, ion release, and electrochemical assessments. The microstructure of the Tie35Nbe5In alloy consisted of acicular a-phase and fine a¿¿-phase within a micrometric b-phase matrix. A low elastic modulus of 63 GPa, as well as hardness and flexural strengths higher than the reported for the human bone, ensured the mechanical adequacy of the alloy. The Ti, Nb, and In releases were below toxic levels for the human body. The electrochemical performance showed the formation of a surface passive layer formation that encouraged a low corrosion rate. The corrosion performance was mainly influenced by chemical heterogeneities (preferred dissolution of Nb segregates) and porosity. Based on the above, the porous Tie35Nbe5In alloy was demonstrated as a promising candidate for biomedical implant applications., This work was made possible with funding support from various sources. VAB acknowledges the funding from the Spanish Ministerio de Ciencia, innovacion y Universidades with research project RTI2018-097810-B-I00, and the European Commission via FEDER funds, which allowed to purchase research equipment and the Microscopy Service at the Universitat Politecnica de Val encia. MCR thanks the Fundacao de Amparo a Pesquisa do Estado de Sao Paulo for financial support to carry out this work with "Projeto Tematico" no 2018/18293-8 and post-doc Grant Nos. 2018/18293-8 and 2021/03865-9.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microstructural and mechanical behavior of second-phase hardened porous refractory Ti-Nb-Zr-Ta alloys

  • González-Guillén, Celia
  • Romero-Resendiz, L.
  • Naeem, M.
  • Vidilli, A.L.
  • Otani, L. B.
  • González, G.
  • Klyatskina, Elizaveta
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Second-phase hardening in refractory high-entropy alloys (RHEAs) has been recognized as one of the main routes to significantly improve their mechanical properties. However, their cost¿benefit should not be compromised. Thus, we designed second-phase strengthened RHEAs by a low-cost powder metallurgy method. We induced the formation of FCC (face-centered cubic) ZrC second phase, which has not been reported in Ti-Nb-Zr-Ta alloys before and may be easily confused with the FCC-Zr due to the complexity of identifying carbon by conventional methods. We used neutron diffraction and electron backscatter diffraction for microstructural studies, as well as hardness, ultrasonic and compression techniques for assessing mechanical properties. Our investigation centered on equiatomic and equimassic Ti-Nb-Zr-Ta alloys, both displaying similar grain morphology and porosity but differing in grain sizes and phases. The variation in grain size was attributed to the influence of Ta as a grain growth pinning element. Our second-phase ZrC hardened alloys revealed higher stiffness and hardness, surpassing those documented in the existing literature., LRR acknowledges the funding from the Programa de Apoyo a la Investigacion y el Posgrado (PAIP-50009223) of the Chemistry College of Universidad Nacional Autonoma de Mexico, as well as from the Programa de Apoyo a Proyectos de Investigacion e Innovacion Tecnologica (PAPIIT)-UNAM under grant number IA102724. MN thanks the Asia-Oceania Neutron Scattering Association (AONSA) for the award of the AONSA Young Research Fellowship (AONSA-YRF-2022). ALV acknowledges FAPESP for financial support in his internship at UPV under the grant number 2021/11537 1. GG acknowledges PAPIIT-UNAM under grant number IN110124. VA acknowledges the funding from the Spanish Ministerio de Ciencia, Innovacion ¿ y Universidades with project RTI2018 097810-B-I00, and the European Commission via European Regional Development Fund (FEDER). The neutron diffraction experiments were performed at TAKUMI in MLF of J-PARC.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Laser Surface Modification in Ti-xNb-yMo Alloys Prepared by Powder Metallurgy

  • Tendero, Inmaculada
  • Rossi, Mariana
  • Viera, Mauricio
  • Amado, José
  • Tobar, M.J.
  • Vicente-Escuder, Ángel
  • Yáñez, Armando
  • Amigó, Vicente
[Abstract] The main objective was to study the effect of surface modification by laser on Ti-Nb-Mo powder metallurgical alloys to improve their mechano-chemical behavior and their application as a biomedical implant. The used powder mixtures were produced in an inert atmosphere. Uniaxial compaction took place at 600 MPa with high-vacuum sintering at 1250 °C for 3 h. The specimens for the three-point flexure test were prepared and their mechanical properties determined. Microstructural characterization was performed by scanning electron microscopy (SEM) and X-ray diffraction (XRD) to obtain the distribution of phases, porosity, size, and shape of the grains of each alloy. Corrosion behavior was evaluated by electrochemical tests using an artificial saliva electrolyte modified from Fusayama at 37 °C. Chemical characterization was completed by analyzing the ionic release by Inductively coupled plasma atomic emission spectroscopy (ICP-EOS) after immersion for 730 h in Fusayama solution modified with NaF at 37 °C to simulate a 20-year life span based on a daily 2-min cycle of three toothbrushes. Corrosion behavior confirmed promising possibilities for the biomedicine field. The surface porosity of the samples not submitted to surface treatment deteriorated properties against corrosion and ion release. The obtained phase was β, with a low α”-martensite percentage. The maximum resistance to bending was greater after surface fusion. Plastic deformations were above 7% under some conditions. Microhardness came close to 300 HV in heat-affected zone (HAZ) and 350 HV in fusion zone (FZ) (under the determined condition. The elastic modulus lowered by around 10%. The corrosion rate was lower in Ti-27Nb-8Mo and Ti-35Nb-6Mo. Niobium release was significant, but below the physiological limit., The authors thank the Ministerio de Economía y Competitividad de España for Research Project RTI2018-097810-B-I00 and the Ministerio de Economía y Competitividad de España for Research Project RTI2018-096472-B-I00. The European Commission thanks to FEDER and the São Paulo State Research Support Foundation (FAPESP) [Grant: 2019/24237-6]., Fundação de Amparo à Pesquisa do Estado de São Paulo; 2019/24237-6
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Effect of Alloying Elements on Laser Surface Modification of Powder Metallurgy to Improve Surface Mechanical Properties of Beta Titanium Alloys for Biomedical Application

  • Rossi, Mariana
  • Amado, José
  • Tobar, M.J.
  • Vicente-Escuder, Ángel
  • Yáñez, Armando
  • Amigó, Vicente
[Abstract] Beta-type titanium alloy surfaces (Tie35Nbe10Ta (TNT) and Tie30Nbe4Sn (TNS)) weremodified by laser using a power of 1000 W and speed of 6.7 mm/s (Condition A) and a powerof 1500 W with speed of 10 mm/s (Condition B). Increasing laser conditions, the thicknessof the molten layer was also increased. The initial equiaxed grains changes to quiteelongated grains shape. The surfaces were structured undera00martensite,aand matrixb.Thebphase content decreased slightly and thea00phase increased for both alloysincreasing the laser conditions. The condition A increased the elastic modulus (E) anddecreased the hardness while condition B did not affect the mechanical properties surfacefor the TNT system compared to base metal (BM). In TNS system the laser condition Adecreased the E and increased the hardness while increasing the laser parameters (Con-dition B) both E and hardness decreased compared to BM. The laser surface treatment wasinfluenced by the levels of alloying elements present promoting most significant changesin the microstructure and mechanical properties in the TNS system, This work was supported by the Ministerio Español de Ciencia, Innovación y Universidades, Spain with Grant RTI2018-097810-B-I00, RTI2018-096472-B-I00 and the European Union (EU) through Fondo Europeo de Desarrollo Regional (FEDER), Spain