Pasar al contenido principal

AVANCES EN MEMBRANAS DE FIBRA HUECA BASADAS EN MOFS Y GRAFENO ENFOCADAS A PROCESOS EFICIENTES DE SEPARACION

MAT2016-77290-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ZARAGOZA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Graphene oxide – Filled polyimide membranes in pervaporative separation of azeotropic methanol–MTBE mixtures

  • Castro-Muñoz, Roberto
  • Galiano, Francesco
  • Iglesia, Óscar de la
  • Fíla, Vlastimil
  • Téllez, Carlos
  • Coronas, Joaquín
  • Figoli, Alberto
Graphene oxide (GO)-polyimide mixed matrix membranes (MMMs) were produced using chloroform by solvent evaporation. These membranes have been used, for the first time, in pervaporation (PV) for the separation of azeotropic methanol (MeOH)- methyl tert-butyl ether (MTBE) mixtures (14.3 and 85.7%, respectively). The effect of GO loading in the PV process was investigated. The PV experiments were carried out at different feed operating temperatures (25–45 °C). Furthermore, an analysis of the PV process through the Arrhenius relationship has been given. The feed temperature (in the range of 25–45 °C) affected the permeation of both components producing an increase in total permeate flux; however, separation factor was compromised. Indeed, the best permeate fluxes (ca. 0.091 kg m−2 h−1) of the MMMs (4 wt% GO) were found at 45 °C, while the best separation factor (α = 28) was found at 1 wt% GO at 25 °C. In addition, the membranes were characterized by TGA, SEM, DSC, solvent uptake and mechanical test (Young’s modulus). Finally, the performance of the GO-polyimide membranes was compared with other polymeric and MMMs membranes at the azeotropic conditions., R. Castro-Muñoz acknowledges the European Commission - Education, Audiovisual and Culture Executive Agency (EACEA) for his PhD scholarship under the program: Erasmus Mundus Doctorate in Membrane Engineering – EUDIME (FPA No 2011-0014, Edition V, http:/eudime.unical.it). This work was partially supported by the Operational Program Prague – Competitiveness (CZ.2.16/3.1.00/24501) and the “National Program of Sustainability“ (NPU I LO1613) MSMT-43760/2015. Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T43-17R) and the ESF is also gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mathematical modeling of temperature and pressure effects on permeability, diffusivity and solubility in polymeric and mixed matrix membranes

  • Maghami, Saeid
  • Mehrabani-Zeinabad, Arjomand
  • Sadeghi, Morteza
  • Sánchez-Laínez, Javier
  • Zornoza, Beatriz
  • Téllez, Carlos
  • Coronas, Joaquín
Due to the temperature and pressure dependency of gas transport through polymeric and mixed matrix membranes, probing of their separation performance at different operational conditions seems crucial to determine an optimal operational condition. To minimize the number of costly and time consuming experiments, a modified form of van’t Hoff-Arrhenius model was developed to consider the simultaneous effects of temperature and pressure on the separation performance of polymeric and mixed matrix membranes. Moreover, the proposed model is capable to consider pressure dependency of energetic parameters of Arrhenius model including activation energies of permeability and diffusivity, heat of sorption and the corresponding pre-exponential factors. The validity of the proposed model was investigated by using permeation coefficients of CO2 and N2 in a binary mixture through 6FDA-DAM at different temperatures in the range of 35–55 °C and in the feed pressure range from 2 to 5 atm. Besides, from data taken from the literature, the proposed model was validated by the prediction of temperature and pressure dependency of transport properties of glassy and rubbery polymers as well as mixed matrix membranes (MMMs) for different gas molecules including He, H2, CO2, O2, N2, CH4 and C4H10. Predictions corresponding to 300 data points revealed that the maximum average absolute relative error was 5.1%., Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T43-17R) and the ESF is gratefully acknowledged. L. P. thanks the Spanish Ministry of Economy, Industry and Competitiveness Program FPI2014 for her PhD grant. J. S.-L. thanks the Spanish Education Ministry Program FPU2014 for his PhD grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Polymer engineering by blending PIM-1 and 6FDA-DAM for ZIF-8 containing mixed matrix membranes applied to CO2 separations

  • Sánchez-Laínez, Javier
  • Pardillos-Ruiz, Alberto
  • Carta, Mariolino
  • Malpass-Evans, Richard
  • McKeown, Neil B.
  • Téllez, Carlos
  • Coronas, Joaquín
The preparation of mixed matrix membranes (MMMs) for post-combustion CO2 capture and biogas upgrading from PIM-1 (10–90 wt%)/6FDA-DAM heterogeneous blends with ZIF-8 as filler (3–20 wt% with regard to the polymer blend) is described. The heterogeneity of the blend, considered here as an advantage for the dispersion of the filler within the MMMs, has been confirmed by the existence of a single glass transition temperature, consistent with that of 6FDA-DAM. The segregation between the two polymeric phases and the filler dispersion has been studied by Raman spectroscopy, SEM microscopy and EDX analysis. Increasing the amount of PIM-1 in the blend makes the d-spacing of the polymer chains higher and increases gas permeability. When embedding filler nanoparticles of ZIF-8, a better compatibility with 6FDA-DAM than with PIM-1 is observed. The filler locates near the interphase between polymers helping its dispersion. The use of small loadings of ZIF-8 enhances the gas separation performance of the MMMs in terms of permeability and selectivity for 50/50 CO2/CH4 and 10/90 CO2/N2 mixtures. The best performing membranes are the blends PIM-1/6FDA-DAM 10/90 (w/w) with 10 wt% of ZIF-8, showing a CO2 permeability of 2891 Barrer, a CO2/CH4 selectivity of 26.6 and 2802 Barrer of CO2 with a CO2/N2 selectivity of 18.1. Importantly, the CO2, N2 and CH4 permeabilities of the pure polymeric blends can be predicted using both the logarithmic and the Maxwell models. A new coupled Maxwell model has also been developed able to calculate the flow through the blends containing ZIF-8 and to predict the gas separation properties of the filler itself., Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T43-17R) and the ESF is gratefully acknowledged. J. S.-L. thanks the Spanish Education Ministry Program FPU2014 for his PhD grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Towards the dehydration of ethanol using pervaporation cross-linked poly(vinyl alcohol)/graphene oxide membranes

  • Castro-Muñoz, Roberto
  • Buera-González, Juan
  • Iglesia, Óscar de la
  • Galiano, Francesco
  • Fíla, Vlastimil
  • Malankowska, Magdalena
  • Rubio, César
  • Figoli, Alberto
  • Téllez, Carlos
  • Coronas, Joaquín
Highly hydrophilic inorganic material graphene oxide (GO) was successfully prepared and incorporated into a cross-linked poly(vinyl alcohol) (PVA) matrix. The obtained mixed matrix membranes (MMMs) have been used for the dehydration of ethanol (10:90% water-ethanol) by pervaporation (PV), monitoring their performance in terms of total permeate flux, partial components fluxes, as well as their separation factor. The effect of filler was analyzed by doubling the GO content (at 0.5, 1.0, and 2.0 wt%) in the MMMs. A complete analysis of the operating temperature (between 40 and 70 °C) was carried out by means of Arrhenius relationship. Moreover, the membranes were characterized by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), differential scanning calorimetry (DSC), thermo-gravimetric analysis (TGA), X-ray diffraction (XRD), Fourier transformed infrared spectroscopy (FTIR), measurements of degree of swelling (uptake), water contact angle (CA) and mechanical properties. At 40 °C, the best performance was provided by the MMMs containing 1 wt% GO, showing a separation factor of 263 and a permeate flux of about 0.137 kg m−2 h−1 (in which 0.133 kg m−2 h−1 corresponds to water). This represents a 75% enhancement of the original permeation rate of pristine cross-linked PVA membranes. Taking into account the promising results, it is likely that these MMMs will provide featured benefits in green processes, e.g. ethanol purification by means of less-energy consumption., R. Castro-Muñoz acknowledges the European Commission - Education, Audiovisual and Culture Executive Agency (EACEA) for his PhD scholarship under the program: Erasmus Mundus Doctorate in Membrane Engineering – EUDIME (FPA No 2011-0014, Edition V, http://eudime.unical.it). This work was partially supported by the Operational Program Prague – Competitiveness (CZ.2.16/3.1.00/24501) and the “National Program of Sustainability” (NPU I LO1613) MSMT-43760/2015. Financial support from the Spanish MINECO and FEDER (MAT2016-77290-R), the Aragón Government (T43-17R) and the ESF is also gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tin-carboxylate MOFs for sugar transformation into methyl lactate

  • Murillo, Beatriz
  • Zornoza, Beatriz
  • Iglesia, Óscar de la
  • Wang, Sujing
  • Serre, Christian
  • Téllez, Carlos
  • Coronas, Joaquín
With the purpose of improving the production of methyl lactate (ML) from sugars (glucose and sucrose), a new metal‐organic framework (MOF) denoted as UZAR‐S10, containing Sn ions and ligand 2‐aminobenzene‐1,4‐dicarboxylate was synthesized. The SEM and PXRD characterization revealed that UZAR‐S10 was highly crystalline. The empirical formula of UZAR‐S10 is [(NH2‐BDC)Sn]·(NH2‐BDC)0.5, i.e., per Sn atom, with one structural ligand molecule and half ligand molecule trapped in the MOF structure. The removal of the trapped ligand by either solvent extraction or thermal treatment damaged the structure of UZAR‐S10, not enabling its activation. The performance of UZAR‐S10 in the production of ML was compared to those achieved with different types of carboxylate MOFs, especially with that of Sn partially substituted Ti tetracarboxylate MOF denoted MIP‐177‐LT (MIP‐177‐LT(Ti/Sn)). The highest ML yields achieved from sucrose were 29.5 % and 42.0 % for UZAR‐S10 and MIP‐177‐LT(Ti/Sn), respectively. For comparison, other carboxylate type MOFs (MIL‐53(Al), NH2‐MIL‐53(Al), UiO‐66, MIL‐101(Cr) and HKUST‐1) were tested at the same conditions with worse performance than the two Tin‐containing MOFs., Financial support from the Spanish Ministry of Economy and Competitiveness (MAT2016–77290‐R) and the European Social Fund (ESF) through the Aragón Government (T43–17R) is gratefully acknowledged., Peer reviewed