Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Numerical evaluation of the plastic hinges developed in headed stud shear connectors in composite beams with profiled steel sheeting

  • Vigneri, Valentino
  • Odenbreit, Christoph
  • Braun, Matthias
[EN] For composite beams using novel steel sheeting, the current Eurocode 4 rules sometimes overestimate the load bearing capacity of the shear connector. This is due to the larger rib heights and the smaller rib widths in comparison with the old studies, which have been carried out to calibrate the current design equations. The RFCS Project “DISCCO” investigated this phenomena and the working group under mandate M515, CEN/TC250/SC4/SC4.T3 is enhancing this equation and working on a proposal to be taken over in the new version of Eurocode 4.The proposed new equation covers the failure behaviour of the shear connection more in detail. The test results show, that the failure consists in a combined concrete cone and stud in bending. Due to the geometry of novel steel sheeting, the load bearing capacity of the headed stud shear connector is no more limited by its shear capacity, but by its bending capacity.A 3D non-linear finite element model is developed and validated through the support of the DISCCO push-out tests. A good agreement between numerical and experimental results in terms of force-slip behaviour is achieved. Special attention of this work lies on the numerical evaluation of the number of plastic hinges ny: a stress-based procedure is presented and the results are compared to the equations presented for new Eurocode 4.The numerical simulations show that the upper plastic hinge moves up as the slip increases due to the progressive crushing of the concrete in the rib. From the parametric study, it turns out that ny is linearly proportional to the embedment depth. Compared to pre-punched hole decking, through-deck welding specimen activates less plastic hinges in the studs because of the higher stiffness provided at the base of the stud., The RFCS project “DISCCO” was supported by the grant agreement number RFSR-CT-2012-00030. Further, the authors gratefully acknowledge the support of ArcelorMittal Global R&D, Long Products Luxembourg.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Flowering phenology and flower quality of cultivars 'Arbequina', 'Koroneiki' and 'Picual' in different environments of southern Spain

  • Navas-López, José F.
  • León, Lorenzo
  • Rapoport, Hava F.
  • Moreno Alías, Inmaculada
  • Medina, María Guacimara
  • Santos, Cristina
  • Porras, Rafael
  • Lorite, Ignacio J.
  • de la Rosa, Raúl
Olive cultivation has been expanding worldwide over the last decades. The expansion to new growing areas with different environmental conditions and the threat of climate change require knowledge of genetic and environmental influences on olive production, to which the phenology and quality of flowering are critical. The IFAPA olive breeding program of Córdoba, Spain, has established comparative trials located in different agro-climatic conditions of Andalucía, southern Spain for testing the response of cultivars and breeding selections to varied environments. This study reports initial results (two years) for flowering of ‘Arbequina’, ‘Koroneiki’ and ‘Picual’ in four locations: three trials in typical olive growing areas Antequera (AN) and Baena (BA), both under rainfed conditions, and Úbeda (UB) with drip irrigation, and the fourth, also with drip irrigation, in Gibraleón (GI), a location with mild winter temperatures at the limit of the Andalusian area of olive cultivation. We observed flowering phenology, bloom period, and flower quality, and assessed the relative influences of genetic and environmental factors and their interaction. Flowering phenology showed high variability among the different growing areas, with earliest full bloom (65) in GI for all cultivars (late April). GI also presented the longest blooming period (around 45 days) for all cultivars, while, ‘Koroneiki’ had the longest blooming period for all locations overall. In flower quality, we observed significant differences both for environments and cultivars. UB showed the best inflorescence quality, with the highest percentage of perfect (hermaphrodite) flowers (PF%), while BA showed the worst PF%, possibly related to both lime-filled soils and rainfed conditions. However, in spite of differences among growing areas, the cultivars consistently presented the same order of PF% in all locations, with highest PF% in ‘Arbequina’, followed by ‘Koroneiki’ and finally ‘Picual’., Financial support provided by projects AVA201601.2 (IFAPA), RTA2012-00018, RTA2014-00030 (INIA) and P11-AGR-7835, all partly funded by European regional development fund (ERDF).