Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

An Innovative Co-Axial Spiral Borehole Heat Exchanger Dynamic Model

  • Cazorla-Marín, Antonio|||0000-0003-3314-0395
  • Montagud- Montalvá, Carla|||0000-0002-7118-6119
  • Ruiz-Calvo, Félix
  • Witte, Henk
  • Corberán, José M.
A dynamic model of a ground source heat pump (GSHP) system is a very useful tool in order to optimize its operation. It might reproduce the thermal behaviour of each component of the system both on a short-term and a long-term basis, as well as the effect that the borehole heat exchanger (BHE) has in the surrounding ground. Hence, it is possible to use this model to develop proper control strategies in order to increase the global system s efficiency as much as possible. In this work, the approach used for the recently developed B2G dynamic model has been extended to a different configuration than the standard U-tube BHE. The new configuration is a novel co-axial spiral BHE designed in the framework of the GEOT CH project (Geothermal Technology for conomic Cooling and Heating), a HORIZON 2020 European project. The model has been validated against experimental data from a real borehole located in Houten, Netherlands. The results show that the B2G approach applied to this specific configuration produces a model that can accurately predict the short-term behaviour of the BHE., The present work has been supported by the European Community Horizon 2020 Program for European Research and Technological Development (2014-2020) inside the framework of the project 656889 – GEOTeCH (Geothermal Technology for Economic Cooling and Heating)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Modelling and energy analysis of a dual source heat pump system in an office building

  • Corberán, José M.
  • Masip Sanchis, Ximo
  • Cazorla-Marín, Antonio|||0000-0003-3314-0395
  • Marchante-Avellaneda, Javier|||0000-0001-5680-5033
  • Montagud- Montalvá, Carla|||0000-0002-7118-6119
This paper presents the modelling and energy analysis of a dual source heat pump system for the production of heating, cooling and domestic hot water (DHW) in buildings. The research work was carried out in the framework of the Geot€ch project ‘GEOthermal Technology for economic Cooling and Heating’. The Geot€ch project, funded by the European commission within the H2020 program, is a four years’ duration project which demonstrates the next generation of ground source heat pump systems with a high energy efficiency but also with lower system costs with respect to those already existing in the market. To this end, one of the objectives of the project is the design of an efficient and comparative low cost ‘plug& play’ system for providing the heating, cooling and DHW needs in three demonstration sites located in Italy, the United Kingdom and the Netherlands respectively. In this context, an innovative dual source heat pump has been developed, which is capable of making optimal use of ground or air environmental heat sources according to operating and climate conditions. On the other hand, in order to reduce the costs of the installation, a new more efficient technology of coaxial borehole heat exchangers will be developed within the framework of the project. The project started on May 2015 and it is still ongoing. This paper first describes the characteristics of the dual source heat pump designed in the project. Then, in order to assist both in the optimal design and energy optimization of the operation of the system, a model of the ‘plug&play’ system in TRNSYS including all the integrated system components (dual source heat pump, ground source heat exchanger, air conditioning and DHW hydraulic loops) is presented for the demo site located in the Netherlands. Finally, the paper presents an analysis of the system operation as well as a first energy assessment in order to identify key control strategies needed to optimize the seasonal energy performance of the system., The present work has been supported by the European Community Horizon 2020 Program for European Research and Technological Development (2014-2020) inside the framework of the project 656889 – GEOTeCH (Geothermal Technology for Economic Cooling and Heating) and by the Generalitat Valenciana inside the program “Ayudas para la contratación de personal investigador en formación de carácter predoctoral (ACIF/2016/131)”.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Modeling, analysis and energy optimization of an air source heat pump system for SHW production

  • Masip Sanchis, Ximo
  • Corberán, José M.
  • Cazorla-Marín, Antonio|||0000-0003-3314-0395
  • Montagud- Montalvá, Carla|||0000-0002-7118-6119
  • Marchante-Avellaneda, Javier|||0000-0001-5680-5033
In order to fulfill with the European normative EN-1717:2000 regarding the general requirements of devices to prevent pollution of potable water by backflow, in those systems using a heat pump (HP) for the production of sanitary hot water (SHW), the coupling of the HP with the storage tank must be indirect. This paper will analyze three of the possible coupling configurations for the case of an air source heat pump system: (i) external brazed plate heat exchanger, (ii) coil heat exchanger inside the storage tank and (iii) double wall condenser at the heat pump. The system will be modeled using a dynamic simulation tool (TRNSYS). The aim of this work is to compare the energy performance of each configuration and to optimize its operation., The present work has been supported by the European Community Horizon 2020 Program for European Research and Technological Development (2014-2020) inside the framework of the project 656889 – GEOTeCH (Geothermal Technology for Economic Cooling and Heating), by the Generalitat Valenciana inside the program “Ayudas para la contratación de personal investigador en formación de carácter predoctoral (ACIF/2016/131)” and by the Ministerio de Educación, Cultura y Deporte inside the programme ‘Formación de Profesorado Universitario (FPU15/03476)’
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

TRNSYS modelling and energy assessment of a dual source heat pump system

  • Cazorla-Marín, Antonio|||0000-0003-3314-0395
  • Montagud- Montalvá, Carla|||0000-0002-7118-6119
  • Marchante-Avellaneda, Javier|||0000-0001-5680-5033
  • Corberán, José M.
Ground source heat pump systems are recognized as one of the most energy efficient renewable systems for heating, cooling and domestic hot water production in buildings. However, the high cost of the Ground Source Heat Exchanger (GSHE) is still a handicap for its widespread use in Europe. In this context, the use of an innovative dual source (air/ground) heat pump developed in the framework of the H2020 Geot ch project could contribute to reduce both the total size of the GSHE and the annual energy consumption of this type of systems. This is possible thanks to the heat pump capability of selecting the most favourable source/sink, with a consequent lower amount of heat exchange needed with the ground. However, the convenience of considering this type of systems is not always straightforward, as it depends on the type of climatological conditions, the thermal demand profile and the ground thermal properties. This assessment is carried out, by means of a complete model developed in TRNSYS, for three different cities in Spain., The present work has been supported by the European Community Horizon 2020 Program for European Research and Technological Development (2014-2020) inside the framework of the project 656889 – GEOTeCH (Geothermal Technology for Economic Cooling and Heating), by the Generalitat Valenciana inside the program “Ayudas para la contratación de personal investigador en formación de carácter predoctoral (ACIF/2016/131)” and by the Ministerio de Educación, Cultura y Derporte inside the program “Formación de Profesorado Universitario (FPU15/03476)”
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Diseño de una bomba de calor de 8 kW con foco de calor dual: aerotermia y geotermia

  • Marchante-Avellaneda, Javier|||0000-0001-5680-5033
  • Cazorla-Marín, Antonio|||0000-0003-3314-0395
  • Montagud- Montalvá, Carla|||0000-0002-7118-6119
  • Corberán, José M.
Debido a la actual preocupación por la preservación del medio ambiente y la reducción de emisiones de CO2, los fabricantes de equipos frigoríficos y bombas de calor invierten mucho tiempo en diseños más eficientes, que cumplan con la actual normativa para el uso de refrigerantes con menor Potencial de Calentamiento Atmosférico (PCA). Nace así el proyecto GEOTeCH, financiado por la Comisión Europea dentro del programa H2020, con el objetivo de encontrar soluciones constructivas para las bombas de calor del futuro, más eficientes y respetuosas con el medio ambiente. Este artículo describe las etapas de diseño de una innovadora bomba de calor dual con dos posibles fuentes de calor: geotérmica y aerotérmica. El diseño final es capaz de funcionar con la máxima eficiencia dando servicio independiente de refrigeración, calefacción y producción de agua caliente sanitaria durante todo el año, haciendo uso de R32 como refrigerante., El presente trabajo cuenta con financiación de la Unión Europea en el marco del Programa Marco Horizonte 2020 de Investigación y Desarrollo Tecnológico Europeo (2014-2020) en el marco del proyecto 656889 GEOTeCH (Geothermal Technology for Economic Cooling and Heating). También se ha recibido financiación por parte de la Generalitat Valenciana en el marco del programa 'Ayudas para la contratación de personal investigador en formación de carácter predoctoral (ACIF / 2016/131)' y por parte del Ministerio de Educación, Cultura y Deporte dentro del programa Formación de Profesorado Universitario (FPU15/03476)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Estimating Ground Thermal Properties of a Borehole Heat Exchanger using the B2G Dynamic Model

  • Cazorla-Marín, Antonio|||0000-0003-3314-0395
  • Montero Reguera, Álvaro Enrique|||0000-0002-4165-4743
  • Montagud- Montalvá, Carla|||0000-0002-7118-6119
  • Ruiz-Calvo, Félix
  • Martos Torres, Julio
  • Corberán, José M.
In situ thermal response tests (TRT s) are currently the standard methodology used for determining ground thermal properties needed for sizing ground source heat exchangers (GSHE). The main drawback of this methodology is the high cost involved, mainly due to the long injection times needed. Since ground conductivity is a key parameter in the design of a GSHE, any advances in the reduction of the duration of a TRT would result in a lower cost. Hence, the viability of this kind of test would increase. In this context, a dynamic model of the GSHE can be very useful to reduce the amount of data needed in order to obtain the ground thermal properties. The recently developed B2G model has proven to be able to reproduce the short-term response of a GSHE with a great accuracy. One of the main advantages of the B2G dynamic model is that it can be adjusted to any specific GSHE with only a few experimental data (typically, corresponding to 10-15 hours of heat injection/extraction). This model could be used to provide an estimation of the ground thermal properties using less data than a standard TRT. In this work, the B2G model has been adapted to an existing borehole heat exchanger (BHE) located at Universitat Politècnica de València. Experimental data corresponding to a TRT performed in this BHE have been used in order to validate the adaptability of the B2G model and its utility as a ground thermal properties estimation tool., The present work has been supported by the European Community Horizon 2020 Program for European Research and Technological Development (2014-2020) inside the framework of the project 656889 – GEOTeCH (Geothermal Technology for Economic Cooling and Heating)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Initial test campaign of an innovative dual source heat pump

  • Marchante-Avellaneda, Javier|||0000-0001-5680-5033
  • Cazorla-Marín, Antonio|||0000-0003-3314-0395
  • Montagud- Montalvá, Carla|||0000-0002-7118-6119
  • Corberán, José M.
This paper describes the experimental setup and the test campaign performed on an innovative prototype of reversible dual source heat pump, with aerothermal and geothermal heat sources working with R32 as refrigerant. The addition of the air source allows the use each time of the most convenient source, hence leading to a considerably higher efficiency, as well as to dramatically reducing the size of the ground source heat exchanger so that the initial cost is much lower than the one of a full geothermal heat pump installation. The design and construction of this unit is the result of the research carried out under the frame of the GEOTeCH, project funded by the European Commission under the H2020 program. This paper first describes the employed experimental setup, and then presents the definition of the test matrix for the characterization of the heat pump performance under each operation mode, which has been based on the Design of Experiments methodology in order to minimize as much as possible the number of test points. 227 test points were acquired, what has allowed the characterization of the unit performance in all operation modes and a broad range of operating conditions, through adequate Response Surfaces. Finally, a comparison of the experimental performance results with the calculations performed with IMST-ART software is presented., The present work has been supported by the European Union under the Horizon 2020 Framework Programme for European Research and Technological Development (2014–20) inside the framework of the project 656889— EOTeCH (Geothermal Technology for Economic Cooling and Heating). Additionally, funding was received by the Generalitat Valenciana inside the programme ‘Ayudas para la contratación de personal investigador en formación de carácter predoctoral (ACIF/2016/131)’ and by the Ministerio de Educación, Cultura y Deporte inside the programme ‘Formación de Profesorado Universitario (FPU15/03476)’
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Adaptation of the B2G dynamic model to new borehole heat exchanger coaxial configurations

  • Cazorla-Marín, Antonio|||0000-0003-3314-0395
  • Montagud- Montalvá, Carla|||0000-0002-7118-6119
  • Corberán, José M.
In order to reach a global reduction in the CO2 emissions, it is key to improve the energy efficiency of systems for producing heating and cooling in buildings. This can be achieved by increasing the use of renewable energies, for instance ground source heat pumps (GSHP). However, special attention should be paid to its optimal design and operation. In this context, the development of dynamic models is a key factor, being the model of the ground source heat exchanger and its coupling to the heat pump particularly important. This coupling needs to be well reproduced both in the short term and long term operation, given that most of the GSHP systems have an on/off operation. In this context, the novel B2G dynamic model was developed and experimentally validated previously for a single U-loop BHE. This work presents the adaptation and experimental validation of the B2G model both to a standard coaxial configuration and to a novel coaxial spiral configuration., The present work has been supported by the European Community Horizon 2020 Program for European Research and Technological Development (2014-2020) inside the framework of the project 656889 – GEOTeCH (Geothermal Technology for Economic Cooling and Heating) and by the Generalitat Valenciana inside the program “Ayudas para la contratación de personal investigador en formación de carácter predoctoral (ACIF/2016/131)”
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Characterization of the performance for water-to-water and air-to-water heat pumps: Development of simple and compact polynomial correlations

  • Marchante-Avellaneda, Javier|||0000-0001-5680-5033
  • Navarro-Peris, Emilio|||0000-0002-0608-2129
  • Corberán, José M.
  • Llopis, Belén
Nowadays, the development of models is one of the most common problems in many research studies. In the field of refrigeration and heating, researchers increasingly require compact models with a reduced computational time. These models must be able to predict the performance of heat pumps and chillers with reasonable accuracy. This paper describe the development of simple and compact polynomial models for the performance characterization in these machines. To this end, this study consists of two main parts: Obtaining the polynomial models and then its final adjustment with experimental data. The unit selected for this study, is an innovative prototype of reversible dual source heat pump, with aerothermal and geothermal heat sources working with R32 as refrigerant. This has enabled us to analyze the response surface for the performance of the two main heat pump technologies: water-to-water and air-to-water heat pumps., The present work has been supported by the European Union under the Horizon 2020 Framework Programme for European Research and Technological Development (2014–20) inside the framework of the project 656889—GEOTeCH (Geothermal Technology for Economic Cooling and Heating). Additionally, funding was received by the Ministerio de Educación, Cultura y Deporte inside the programme ‘Formación de Profesorado Universitario (FPU15/03476)’.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Nuevo modelo dinámico de un intercambiador enterrado en TRNSYS: adaptación del modelo B2G a largos periodos de simulación

  • Cazorla-Marín, Antonio|||0000-0003-3314-0395
  • Montagud- Montalvá, Carla|||0000-0002-7118-6119
  • Ruiz-Calvo, Félix
  • Corberán, José M.
El uso de modelos que simulen el comportamiento de una instalación está ampliamente extendido como ayuda en el diseño y optimización de sistemas de climatización. En un sistema de bomba de calor geotérmica, el intercambiador enterrado es uno de los componentes más importantes, y uno de los más complejos de modelar. Existe una gran variedad de modelos de intercambiador enterrado. La mayoría de los modelos existentes se centran en modelar el comportamiento a corto o a largo plazo. Por otra parte, existen algunos modelos que engloban tanto el corto como el largo plazo; sin embargo, estos requieren un coste computacional muy alto. En el presente trabajo, se presenta el modelado de un intercambiador enterrado situado en la Universitat Politècnica de València, el cual consiste en la utilización de un nuevo modelo dinámico (B2G) desarrollado en TRNSYS que simula el comportamiento del intercambiador enterrado con una gran precisión y un coste computacional bajo, a corto plazo. Para modelar el largo plazo, se propone acoplar el B2G a otro modelo ya existente y ampliamente conocido. Se consideran dos modelos de largo plazo distintos: el modelo DST existente en TRNSYS y el modelo g-function. Finalmente, se comparan los resultados de simulación en ambos casos. Los resultados obtenidos muestran que el modelo B2G acoplado a cualquiera de los dos modelos a largo plazo estudiados reproduce con gran precisión el comportamiento real del intercambiador. Esto refleja su alta versatilidad, ya que puede trabajar combinado con diferentes modelos de intercambiador enterrado a largo plazo, Este trabajo ha sido financiado por el proyecto europeo del programa Horizonte 2020 “Geothermal Technology for €conomic Cooling and Heating” (GEOT€CH)