Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Measurements and modeling of sediment transport during offshore and onshore bar migration

  • Grossmann, Florian|||0000-0002-1037-2372
  • Hurther, David
  • Sánchez-Arcilla Conejo, Agustín|||0000-0002-3450-6697
  • Alsina Torrent, José María|||0000-0002-3055-5379
Effective design of interventions in the coastal zone (flood defense, nourishments, etc.) requires understanding of long term coastal evolution. Historically, such evolution has been difficult to model because of different processes in storms and calm conditions, and the specific calibration factors required. This knowledge gap partly resulted from difficulties in measuring bedload and accretive transport processes at high detail. In the present study such measurements were obtained in the shoaling and outer surf zone of large-scale wave flume experiments with offshore-/onshore-migrating breaker bars. Physical insight from the measurements guided model decisions in a practical modeling approach separating bedload and suspended load but using the same calibration for storm and calm conditions. As a result, good replication (most tests within factor 2) of measured transport rates is obtained on the basis of free stream velocities. Identified priorities for development include parametrization of hydraulic roughness and wave breaking’s influences on entrainment and suspension., The experiments described in this work were funded by the EU Horizon 2020 Research and Innovation Programme through HYDRALAB+ Contract no. 654110. FG acknowledges PhD funding from the Agency for Management of University and Research Grants (AGAUR). Further funding was provided by the REST-COAST project which receives funding from the EU Horizon 2020 Research and Innovation Programme under Grant Agreement number 101037097.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

MODEX: Laboratory experiment exploring sediment spreading of a mound under waves and currents

  • de Schipper, Matthieu
  • Hopkins, Julia
  • Wengrove, Meagan E.
  • Saxoni, Ioanna
  • Kleinhans Maarten, G.
  • Senechal, Nadia
  • Castelle, Bruno
  • Ribas Prats, Francesca|||0000-0003-4701-5982
  • Ruessink, Gerben
  • Murphy, Brendan
  • McLelland, Stuart J.
The dispersal of sand from submerged mounds in the nearshore is driven by the interplay of processes such as converging and recirculating flows, changing roughness, bed slope effects and wave focusing/refraction. This morphological diffusivity is key to understanding sand bars in shallow seas, tidal inlets, estuaries, and the nearshore response to human interventions such as nourishments and dredging. Most of the work on the evolution of submerged mounds has been based on fluvial studies, focusing on flow without waves. In these cases, circular mounds tend to deform to crescentic (barchan) shapes. In contrast, observations of sandbars and berms in the nearshore subjected to waves show much more complex translation and deformation behavior. This contribution introduces the laboratory MOrphological Diffusivity Experiment (MODEX) aimed at examining morphological diffusivity under different forcing conditions. The experiment particularly addresses the linkages between small scale (local) effects (e.g. bed slope, bedforms) on the adjustment of sandy mounds., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

SPH simulation of wave breaking over a barred beach and comparison with experiments

  • Scandura, Pietro
  • Altomare, Corrado|||0000-0001-8817-0431
  • Cáceres Rabionet, Iván|||0000-0002-7426-7029
  • Viccione, Giacomo
  • Van Der A, Dominic
This paper presents an SPH numerical simulation of the hydrodynamics due to monochromatic waves breaking on a rigid barred beach profile. The simulation is compared with large–scale laboratory experiments, in which detailed water surface measurements were made at 22 cross-shore locations. The results include wave heights, and the phase-averaged velocity and time-mean velocities along the bar. Overall, the SPH model is able to reproduce several features of this complex flow. Information about the correct setup of an SPH simulation to accurately reproduce the physical processes involved in the wave breaking is also reported. The results show that a recirculating cell, just above the bar through, is generated because of wave breaking. The flow in this cell contributes to the growth of the bar when the bed is made up of mobile material., The experiments were supported by the European Community’s Horizon 2020 Programme through the grant to the budget of the integrated infrastructure initiative HYDRALAB+, Contract no. 654110, and were conducted as part of the transnational access project HYBRID. P.S. acknowledges the support received from the University of Catania through the funding of the research project ‘Valutazione del rischio idraulico in sistemi complessi (VARIO)’. G.V. acknowledges the support received from the University of Salerno through the funding of the research project ‘Analisi del comportamento di flussi geofisici a superficie libera’. Dr. Corrado Altomare acknowledges funding from Spanish government and the European Social Found (ESF) under the programme ‘Ramón y Cajal 2020’ (RYC2020-030197-I/AEI/ 10.13039/501100011033).
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Ship manoeuvring effects on propeller induced erosion

  • Mujal Colilles, Anna|||0000-0003-0139-3849
  • Llull Marroig, Antoni Ignaci|||0000-0002-4234-4173
  • Castells Sanabra, Marcel·la|||0000-0002-9038-3126
  • Gironella Cobos, Xavier|||0000-0002-8862-5704
  • Martínez de Osés, Francesc Xavier|||0000-0001-9997-6246
  • Sánchez-Arcilla Conejo, Agustín|||0000-0002-3450-6697
The shipping industry evolution over the last decades has led to growing structural and operational problems, in particular, for old marinas with lower depths to hosts present ships and with higher drafts and power of engines. The increase in capacity, size, power and self-propulsion of present ships is the main cause behind morphodynamic sea bed changes in harbour basins. This is producing two different but linked problems: scouring effects near the structures, affecting their stability, and sedimentation of the scoured material in other areas of the basin that reduces the average depth of the basin and the ship motions become uncontrollable. The present contribution aims to compare two different manoeuvring situations in a confined scenario, using laboratory data. Laboratory experiments have been carried out at the Marine Engineering Laboratory facility LaBassa. The two manoeuvring situations, modelled at bollard pull condition are permanent docking/backward and permanent undocking/forward using three different propeller revolutions at a fixed pitch angle and blade area ratio and two fixed locations of the propellers from the wall. The potential erosion is measured through an ecosound scanner of the control area over a homogeneous sandy bed. The evolution of the maximum erosion depth behaviour is completely different for undocking and docking operations. Undocking/backward results show higher depths at the initial stages reaching an almost asymptotic state at the end of the experiments whereas maximum erosion depth during forward operations increases monotonically over time.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

The MARHIS network: an application to composite modelling for overtopping

  • Sánchez-Arcilla Conejo, Agustín|||0000-0002-3450-6697
  • López Lara, Javier
  • Marzeddu, Andrea|||0000-0001-9515-7323
  • Alvarez, Alvaro
  • Gironella Cobos, Xavier|||0000-0002-8862-5704
  • Mujal Colilles, Anna|||0000-0003-0139-3849
  • Losada, Iñigo
This paper presents the MARHIS network, an added value aggregation of hydraulic facilities and numerical modelling tools plus field equipment from the Catalonia University of Technology and IH Cantabria. The paper presents the origin and objectives of such a network, emphasizing the applications to coastal harbour and offshore cases. This is based on a summarized description of the facilities and tools in IH Cantabria and LIM-UPC. A summarized description of the third element forming the MARHIS network (CEHIPAR) in Madrid is also presented. The next section deals with a composite modelling approach and how to develop and apply it to a) wave structure interactions and b) sediment propeller interactions. The paper ends with some conclusions about the MARHIS network and the benefits such structure should provide to composite modelling, a tough challenge for present engineering applications.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

The MARHIS network: an application to composite modelling for overtopping

  • Sánchez-Arcilla Conejo, Agustín
  • López Lara, Javier
  • Marzeddu, Andrea
  • Alvarez, Alvaro
  • Gironella Cobos, Xavier
  • Mujal Colilles, Anna
  • Losada, Iñigo
This paper presents the MARHIS network, an added value aggregation of hydraulic facilities and numerical modelling tools plus field equipment from the Catalonia University of Technology and IH Cantabria. The paper presents the origin and objectives of such a network, emphasizing the applications to coastal harbour and offshore cases. This is based on a summarized description of the facilities and tools in IH Cantabria and LIM-UPC. A summarized description of the third element forming the MARHIS network (CEHIPAR) in Madrid is also presented. The next section deals with a composite modelling approach and how to develop and apply it to a) wave structure interactions and b) sediment propeller interactions. The paper ends with some conclusions about the MARHIS network and the benefits such structure should provide to composite modelling, a tough challenge for present engineering applications., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

SPH simulation of wave breaking over a barred beach and comparison with experiments

  • Scandura, Pietro
  • Altomare, Corrado
  • Cáceres Rabionet, Iván
  • Viccione, Giacomo
  • Van Der A, Dominic
This paper presents an SPH numerical simulation of the hydrodynamics due to monochromatic waves breaking on a rigid barred beach profile. The simulation is compared with large–scale laboratory experiments, in which detailed water surface measurements were made at 22 cross-shore locations. The results include wave heights, and the phase-averaged velocity and time-mean velocities along the bar. Overall, the SPH model is able to reproduce several features of this complex flow. Information about the correct setup of an SPH simulation to accurately reproduce the physical processes involved in the wave breaking is also reported. The results show that a recirculating cell, just above the bar through, is generated because of wave breaking. The flow in this cell contributes to the growth of the bar when the bed is made up of mobile material., The experiments were supported by the European Community’s Horizon 2020 Programme through the grant to the budget of the integrated infrastructure initiative HYDRALAB+, Contract no. 654110, and were conducted as part of the transnational access project HYBRID. P.S. acknowledges the support received from the University of Catania through the funding of the research project ‘Valutazione del rischio idraulico in sistemi complessi (VARIO)’. G.V. acknowledges the support received from the University of Salerno through the funding of the research project ‘Analisi del comportamento di flussi geofisici a superficie libera’. Dr. Corrado Altomare acknowledges funding from Spanish government and the European Social Found (ESF) under the programme ‘Ramón y Cajal 2020’ (RYC2020-030197-I/AEI/ 10.13039/501100011033)., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Ship manoeuvring effects on propeller induced erosion

  • Mujal Colilles, Anna
  • Llull Marroig, Antoni Ignaci
  • Castells Sanabra, Marcel·la
  • Gironella Cobos, Xavier
  • Martínez de Osés, Francesc Xavier
  • Sánchez-Arcilla Conejo, Agustín
The shipping industry evolution over the last decades has led to growing structural and operational problems, in particular, for old marinas with lower depths to hosts present ships and with higher drafts and power of engines. The increase in capacity, size, power and self-propulsion of present ships is the main cause behind morphodynamic sea bed changes in harbour basins. This is producing two different but linked problems: scouring effects near the structures, affecting their stability, and sedimentation of the scoured material in other areas of the basin that reduces the average depth of the basin and the ship motions become uncontrollable. The present contribution aims to compare two different manoeuvring situations in a confined scenario, using laboratory data. Laboratory experiments have been carried out at the Marine Engineering Laboratory facility LaBassa. The two manoeuvring situations, modelled at bollard pull condition are permanent docking/backward and permanent undocking/forward using three different propeller revolutions at a fixed pitch angle and blade area ratio and two fixed locations of the propellers from the wall. The potential erosion is measured through an ecosound scanner of the control area over a homogeneous sandy bed. The evolution of the maximum erosion depth behaviour is completely different for undocking and docking operations. Undocking/backward results show higher depths at the initial stages reaching an almost asymptotic state at the end of the experiments whereas maximum erosion depth during forward operations increases monotonically over time., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Measurements and modeling of sediment transport during offshore and onshore bar migration

  • Grossmann, Florian
  • Hurther, David
  • Sánchez-Arcilla Conejo, Agustín
  • Alsina Torrent, José María
Effective design of interventions in the coastal zone (flood defense, nourishments, etc.) requires understanding of long term coastal evolution. Historically, such evolution has been difficult to model because of different processes in storms and calm conditions, and the specific calibration factors required. This knowledge gap partly resulted from difficulties in measuring bedload and accretive transport processes at high detail. In the present study such measurements were obtained in the shoaling and outer surf zone of large-scale wave flume experiments with offshore-/onshore-migrating breaker bars. Physical insight from the measurements guided model decisions in a practical modeling approach separating bedload and suspended load but using the same calibration for storm and calm conditions. As a result, good replication (most tests within factor 2) of measured transport rates is obtained on the basis of free stream velocities. Identified priorities for development include parametrization of hydraulic roughness and wave breaking’s influences on entrainment and suspension., The experiments described in this work were funded by the EU Horizon 2020 Research and Innovation Programme through HYDRALAB+ Contract no. 654110. FG acknowledges PhD funding from the Agency for Management of University and Research Grants (AGAUR). Further funding was provided by the REST-COAST project which receives funding from the EU Horizon 2020 Research and Innovation Programme under Grant Agreement number 101037097., Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

MODEX: Laboratory experiment exploring sediment spreading of a mound under waves and currents

  • de Schipper, Matthieu
  • Hopkins, Julia
  • Wengrove, Meagan E.
  • Saxoni, Ioanna
  • Kleinhans Maarten, G.
  • Senechal, Nadia
  • Castelle, Bruno
  • Ribas Prats, Francesca
  • Ruessink, Gerben
  • Murphy, Brendan
  • McLelland, Stuart J.
The dispersal of sand from submerged mounds in the nearshore is driven by the interplay of processes such as converging and recirculating flows, changing roughness, bed slope effects and wave focusing/refraction. This morphological diffusivity is key to understanding sand bars in shallow seas, tidal inlets, estuaries, and the nearshore response to human interventions such as nourishments and dredging. Most of the work on the evolution of submerged mounds has been based on fluvial studies, focusing on flow without waves. In these cases, circular mounds tend to deform to crescentic (barchan) shapes. In contrast, observations of sandbars and berms in the nearshore subjected to waves show much more complex translation and deformation behavior. This contribution introduces the laboratory MOrphological Diffusivity Experiment (MODEX) aimed at examining morphological diffusivity under different forcing conditions. The experiment particularly addresses the linkages between small scale (local) effects (e.g. bed slope, bedforms) on the adjustment of sandy mounds., Peer Reviewed, Postprint (published version)
UCrea Repositorio Abierto de la Universidad de Cantabria
Publicación Contribución de congreso (ConferenceOutput)

Physical Model Tests on Spar Buoy for Offshore Floating Wind Energy Conversion

  • Tomasicchio, Giuseppe Roberto
  • Vicinanza, Diego
  • Belloli, Marco
  • Lugli, Claudio
  • Latham, John-Paul
  • Iglesias Rodriguez, Jose Gregorio
  • Jensen, Bjarne
  • Vire, Axelle
  • Monbaliu, Jaak
  • Taruffi, Federico
  • Pustina, Luca
  • Leone, Elisa
  • Russo, Sara
  • Francone, Antonio
  • Fontanella, Alessandro
  • Di Carlo, Simone
  • Muggiasca, Sara
  • Decorte, Griet
  • Rivera, Irene
  • Ferrante, Vincenzo
  • Battistella, Tommaso
  • Guanche García, Raúl
  • Martínez Díaz, Abel
  • Elsässer, Björn
  • Via-Estrem, Lluis
  • Xiang, Jiansheng
  • Andersen, Morten Thøtt
  • Kofoed, Jens Peter
  • Bech Kramer, Morten
  • Musci, Elena
  • Lusito, Letizia
ABSTRACT: The present paper describes the experiences gained from the design methodology and operation of a 3D physical modelexperiment aimed to investigate the dynamic behaviour of a spar buoy floating offshore wind turbine. The physical model consists in a Froude-scaled NREL 5MW reference wind turbine (RWT) supported on the OC3-Hywind floating platform. Experimental tests have been performed at Danish Hydraulic Institute (DHI) offshore wave basin within the European Union-Hydralab+ Initiative, in April 2019. The floating wind turbine model has been subjected to a combination of regular and irregular wave attacks and different wind loads. Measurements of displacements, rotations, accelerations, forces response of the floating model and at the mooring lines have been carried out. First, free decay tests have been analysed to obtain the natural frequency and the modal damping ratios of each degree of freedom governing the offshore. Then, the results concerning regular waves, with orthogonal incidence to the structure, are presented. The results show that most of longitudinal dynamic response occurs at the wave frequency and most of lateral dynamic response occurs at rigid-body frequencies., This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 654110, HYDRALAB+.
UCrea Repositorio Abierto de la Universidad de Cantabria
Publicación Contribución de congreso (ConferenceOutput)

Hidrodinámica y evolución del fondo en ecosistemas vegetados intermareales

  • Maza Fernández, María Emilia
  • García-Maribona López-Sela, Julio|||0000-0003-1385-4403
  • Argemi, Marta
  • López Lara, Javier|||0000-0003-0968-1909
  • Gillis, Lucy G.
  • Balke, Thorstenb
  • Suzuki, Tomohiro
Este trabajo ha sido financiado por el proyecto HyWEdges (hydrodynamics at coastal wetland edges) dentro de Hydralab+, financiado por el programa EUHorizon2020 Research and Innovation Programme, Grant Agreement 654110.