Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Numerical modal analysis of a Kaplan turbine runner

  • Roig Bauzà, Rafel
  • Torre Rodríguez, Óscar de la
  • Jou Santacreu, Esteban|||0000-0001-6991-6250
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
The aim of the research has been to investigate the change of dynamic behavior of a Kaplan turbine runner when submerged in still water. More specifically, the effects of the added mass on the modes of vibration have been quantified. For that, the modes of vibration of the runner in vacuum, in air and in water have been simulated with a coupled Acoustic-Structural modal analysis and, from their comparison, the reduction of the natural frequencies and the possible changes of the mode shapes have been determined. The results show that the typically assumed invariance of all the mode shapes of a structure when submerged in a dense fluid is not fully accomplished in this particular geometry. And regards to the frequency reduction ratios, they are found to be similar for the first six modes with an average value of about 37%., This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 814958. The authors also wish to acknowledge Vattenfall for the support., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Understanding the modal response of a full-scale 200 MW Francis turbine runner

  • Roig Bauzà, Rafel
  • Sánchez Botello, Xavier
  • Wiborg, Erik
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
Under off-design operating conditions, the flow through hydraulic turbines presents fluidodynamic disturbances that can excite a natural frequency and provoke a resonance. Determining with precision the modal properties of the runner is thus of paramount importance. The current article presents an experimental modal analysis of a 200 MW Francis runner located in the Oksla hydropower plant in Norway. During the test, the runner was bolted to the still shaft supported by the bearings and an instrumented hammer was used to excite it. Then, several accelerometers were fixed to the band and blades to measure its modal response. Subsequently, frequency response functions between the hammer impulsive force and the vibration acceleration signals were computed to determine the natural frequencies and mode shapes of the Oksla runner. Even though the main modes corresponded to nodal diameters, other more complex modes were also identified on the blades. Nevertheless, a significant disagreement was found when comparing the experimental results with the numerical predictions from a similar but not exactly equal Francis geometry, which confirms the need to scan the actual shapes and dimensions of the runner in order to obtain reliable simulated results., This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 814958. The authors also wish to acknowledge the technical support received from Statkraft.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Large Eddy Simulation of the transient cavitating vortical flow in the wake of a hydrofoil

  • Chen, Jian
  • Geng, Linlin
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
The Zwart mixture cavitation model and the Large Eddy Simulation (LES) turbulence model have been combined to simulate the transient cavitating flow in the wake of a hydrofoil. The hydrofoil is a 2D NACA0009 with a truncated trailing edge which has been extensively investigated experimentally in the EPFL high-speed cavitation tunnel. The simulated flow conditions correspond to a free stream velocity of 20 m/s (Re = 2 × 106) and an incidence angle of 0° for different levels of cavitation number, ¿¿, ranging from free cavitation to cavitation flow with different amounts of vapor. Under such hydrodynamic conditions and blunt trailing edge geometry, a Von Kármán vortex street takes place that is the object of the present study in order to ascertain how cavitation modifies the vortex structure and its dynamic behavior. The numerical results show a good agreement with the experimentally measured vortex shedding frequency without and with cavitation. As observed experimentally, the numerical results also predict an increase of the frequency induced by a significant change of the vortex properties. In order to identify the effects induced by the occurrence and development of cavitation, the obtained unsteady velocity field has been analyzed via Proper Orthogonal Decomposition (POD) technique to identify and understand changes in the flow structure. It has been found that the occurrence and development of cavitation can change the contribution of the POD modes to the total velocity filed. Moreover, the appearance of cavitation seems to stabilize the flow field unsteady behavior since high order POD modes are harmonically correlated with the first couple of basic POD modes., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

PZT actuators as on-board instruments to reduce vibrations and strains in submerged structures

  • Sánchez Botello, Xavier
  • Torre Rodríguez, Óscar de la
  • Roig Bauzà, Rafel
  • Costa Castelló, Ramon|||0000-0003-2553-5901
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
This paper presents the design and evaluation of an active control system to reduce vibrations and strains of submerged structures. For that, a metallic disk mounted in a test rig has been equipped with on-board waterproof strain gauges and accelerometers, to measure its structural response, and with an on-board PZT actuator patch, to provide the required control force. This control force is computed in real-time by an optimal algorithm that determines the exact voltage to be supplied to the PZT patch in order to mitigate any increase of vibrations and/or strains detected by the sensors. In order to capture the dynamics of the structure when it is excited both in air and submerged in water, a plant model has been identified from the Frequency Response Functions (FRFs) obtained experimentally from the measured vibrations and numerically from simulated strains. With these plant models, two different control techniques based on a Linear Quadratic Gaussian (LQG) controller and on an H8 controller have been implemented and simulated under different types of excitations. The obtained results are satisfactory and support the need to continue the research to validate them experimentally., This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 814958., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Numerical assessment of parameters influencing the modal response of a Kaplan turbine model

  • Roig Bauzà, Rafel
  • Torre Rodríguez, Óscar de la
  • Jou Santacreu, Esteban|||0000-0001-6991-6250
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
The present study intends to investigate numerically the impact of: i) the fluid added mass, ii) the turbine rotational speed and iii) the variation of the runner blade bearing stiffness due to the turbine water head on the modal response of a reduced scale Kaplan turbine. The impact of each variable has been quantified by means of a series of numerical modal analyses of the turbine in vacuum and in water, and at rest and rotating. It has been found that the natural frequencies of the Kaplan turbine model are sensitive to all the variables investigated in the present paper, the added mass being the factor which has the greatest impact., This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 814958. The authors also wish to acknowledge Vattenfall for the technical support received for developing this work., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Experimental and numerical modal analysis of a reduced scale Kaplan turbine model

  • Roig Bauzà, Rafel
  • Torre Rodríguez, Óscar de la
  • Jou Santacreu, Esteban|||0000-0001-6991-6250
  • Mulu, Berhanu
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
This paper presents an experimental modal test of a Kaplan turbine model and provides the corresponding analysis of the results. The modal test, which included both the runner and the shaft line, was performed using an impact hammer and a shaker as exciters and several accelerometers as sensors. Additionally, a numerical model of the Kaplan turbine has been built and validated in air. By comparing the numerical and experimental results, the main modes of vibration of the rotor and a runner blade in dry conditions have been identified and discussed. Finally, the rotor has also been tested in wet conditions (still water), and the results have been compared with those calculated from a numericalmodelincluding water as an acoustic domain., This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 814958. The authors also wish to acknowledge the technical support received from Vattenfall and Lightness by Design., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Assessment of fiber bragg grating sensors for monitoring induced strains on the draft tube cone of hydraulic turbines

  • Sánchez Botello, Xavier
  • Roig Bauzà, Rafel
  • Torre Rodríguez, Óscar de la
  • Madrigal, Javier
  • Sales, Salvador
  • Mulu, Berhanu
  • Högström, Carl-Maikel
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
In hydraulic turbines, several flow instabilities can take place inside the draft tube cone during off-design and transient operating conditions such as the rotating vortex rope which can severely damage the structure if sustained in time. In the frame of the AFC4Hydro H2020 research project, an extensive measurement campaign has been carried out to monitor and predict this rotating vortex rope phenomenon in a reduced scale Kaplan turbine model at the Vattenfall Research and Development facility in Älvkarleby, Sweden. The hydraulic turbine model has been operated in propeller mode with a fixed blade angle corresponding to its best efficiency point. Several sensors have been placed along the test stand to monitor vibrations, strains and pressures. Concretely, the present paper assesses the performance of using Fiber Bragg Grating sensors to measure the strains induced on the draft tube cone walls with high-spatial resolution in three different zones of influence: the upper and lower flanges and the vertical cone wall between the runner outlet and the elbow. To do so, a total of 3 arrays embedding a total of 48 Fiber Bragg Grating sensors were glued inside three grooves previously machined on these particular areas of the draft tube cone. Analysing the frequency response of the different Fiber Bragg Grating sensors, the strain patterns induced by the rotating and plunging components of the rotating vortex rope have been precisely determined. Moreover, their impacts at the different part load conditions tested have also been quantified., This work was supported by the funding received from the European Union’s Horizon H2020 research and innovation program under grant agreement No 814958. The authors would like to acknowledge the technical support received from Vattenfall AB.
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Numerical investigation of the effects of hydrofoil vibrations on the unsteady behavior of cavitation

  • Geng, Linlin
  • Chen, Jian
  • Torre Rodríguez, Óscar de la
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
In order to better understand the fluid-structure interaction (FSI) in hydraulic machines, this study aims to numerically investigate the flow around an oscillating hydrofoil with special attention on the effect of unsteadiness on leading edge cavitation. The cavitating flow has been modelled as incompressible with a Shear Stress Transport (SST) turbulence model coupled with a transition model, and with a mass transport equation between vapor and water. The sinusoidal motion of the hydrofoil has been implemented by using a moving mesh technique. The numerical results, which have been validated with experimental data, show that a critical frequency exists showing two different behaviors. For pitching frequencies above this critical frequency, the cavitation shedding frequency is linearly dependent on the pitching frequency. Moreover, this change of cavitation dynamics is explained by a pressure phase shift and an amplitude change observed as the pitching frequency increases., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Mass transfer rate effects on the cavitating vortex shedding flow around a circular cylinder at low Reynolds number

  • Chen, Jian
  • Escaler Puigoriol, Francesc Xavier|||0000-0002-9374-7749
Cavitating vortex shedding is a flow phenomenon commonly encountered behind bluff bodies in hydraulic machinery and systems and the generated vapor bubbles significantly change the dynamic behavior of the vortices. In addition, the collapses of the cavities become a source of unwanted effects such as vibration, noise and material erosion. In this study, the numerical results of the cavitating vortex shedding behind a circular cylinder at low Reynolds number have been compared and analyzed using different mass transfer rate values between the vapor and the liquid water phases. For that, the transport equation for the vapor volume fraction coupled with the explicit source term based on the simplification of the Rayleigh-Plesset equation has been solved. Commonly, this explicit source term that accounts for the mass transfer rate is driven by a function of the pressure difference, the vapor volume fraction and several empirical factors. To understand the effects of this rate, its value has been gradually increased from its default value up to the infinite when the equilibrium assumption for the barotropic flow is satisfied. The obtained results show that as the rate is increased, higher gradients of the vapor volume fraction and of the pressure near the interface between the vapor and the liquid phases are predicted. However, the frequency of the vortex shedding is slightly affected by the increase of the mass transfer rate., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Numerical assessment of parameters influencing the modal response of a Kaplan turbine model

  • Roig Bauzà, Rafel
  • Torre Rodríguez, Óscar de la
  • Jou Santacreu, Esteban
  • Escaler Puigoriol, Francesc Xavier
The present study intends to investigate numerically the impact of: i) the fluid added mass, ii) the turbine rotational speed and iii) the variation of the runner blade bearing stiffness due to the turbine water head on the modal response of a reduced scale Kaplan turbine. The impact of each variable has been quantified by means of a series of numerical modal analyses of the turbine in vacuum and in water, and at rest and rotating. It has been found that the natural frequencies of the Kaplan turbine model are sensitive to all the variables investigated in the present paper, the added mass being the factor which has the greatest impact., This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 814958. The authors also wish to acknowledge Vattenfall for the technical support received for developing this work., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Experimental and numerical modal analysis of a reduced scale Kaplan turbine model

  • Roig Bauzà, Rafel
  • Torre Rodríguez, Óscar de la
  • Jou Santacreu, Esteban
  • Mulu, Berhanu
  • Escaler Puigoriol, Francesc Xavier
This paper presents an experimental modal test of a Kaplan turbine model and provides the corresponding analysis of the results. The modal test, which included both the runner and the shaft line, was performed using an impact hammer and a shaker as exciters and several accelerometers as sensors. Additionally, a numerical model of the Kaplan turbine has been built and validated in air. By comparing the numerical and experimental results, the main modes of vibration of the rotor and a runner blade in dry conditions have been identified and discussed. Finally, the rotor has also been tested in wet conditions (still water), and the results have been compared with those calculated from a numericalmodelincluding water as an acoustic domain., This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 814958. The authors also wish to acknowledge the technical support received from Vattenfall and Lightness by Design., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Understanding the modal response of a full-scale 200 MW Francis turbine runner

  • Roig Bauzà, Rafel
  • Sánchez Botello, Xavier
  • Wiborg, Erik
  • Escaler Puigoriol, Francesc Xavier
Under off-design operating conditions, the flow through hydraulic turbines presents fluidodynamic disturbances that can excite a natural frequency and provoke a resonance. Determining with precision the modal properties of the runner is thus of paramount importance. The current article presents an experimental modal analysis of a 200 MW Francis runner located in the Oksla hydropower plant in Norway. During the test, the runner was bolted to the still shaft supported by the bearings and an instrumented hammer was used to excite it. Then, several accelerometers were fixed to the band and blades to measure its modal response. Subsequently, frequency response functions between the hammer impulsive force and the vibration acceleration signals were computed to determine the natural frequencies and mode shapes of the Oksla runner. Even though the main modes corresponded to nodal diameters, other more complex modes were also identified on the blades. Nevertheless, a significant disagreement was found when comparing the experimental results with the numerical predictions from a similar but not exactly equal Francis geometry, which confirms the need to scan the actual shapes and dimensions of the runner in order to obtain reliable simulated results., This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 814958. The authors also wish to acknowledge the technical support received from Statkraft., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Numerical modal analysis of a Kaplan turbine runner

  • Roig Bauzà, Rafel
  • Torre Rodríguez, Óscar de la
  • Jou Santacreu, Esteban
  • Escaler Puigoriol, Francesc Xavier
The aim of the research has been to investigate the change of dynamic behavior of a Kaplan turbine runner when submerged in still water. More specifically, the effects of the added mass on the modes of vibration have been quantified. For that, the modes of vibration of the runner in vacuum, in air and in water have been simulated with a coupled Acoustic-Structural modal analysis and, from their comparison, the reduction of the natural frequencies and the possible changes of the mode shapes have been determined. The results show that the typically assumed invariance of all the mode shapes of a structure when submerged in a dense fluid is not fully accomplished in this particular geometry. And regards to the frequency reduction ratios, they are found to be similar for the first six modes with an average value of about 37%., This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 814958. The authors also wish to acknowledge Vattenfall for the support., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Large Eddy Simulation of the transient cavitating vortical flow in the wake of a hydrofoil

  • Chen, Jian
  • Geng, Linlin
  • Escaler Puigoriol, Francesc Xavier
The Zwart mixture cavitation model and the Large Eddy Simulation (LES) turbulence model have been combined to simulate the transient cavitating flow in the wake of a hydrofoil. The hydrofoil is a 2D NACA0009 with a truncated trailing edge which has been extensively investigated experimentally in the EPFL high-speed cavitation tunnel. The simulated flow conditions correspond to a free stream velocity of 20 m/s (Re = 2 × 106) and an incidence angle of 0° for different levels of cavitation number, ¿¿, ranging from free cavitation to cavitation flow with different amounts of vapor. Under such hydrodynamic conditions and blunt trailing edge geometry, a Von Kármán vortex street takes place that is the object of the present study in order to ascertain how cavitation modifies the vortex structure and its dynamic behavior. The numerical results show a good agreement with the experimentally measured vortex shedding frequency without and with cavitation. As observed experimentally, the numerical results also predict an increase of the frequency induced by a significant change of the vortex properties. In order to identify the effects induced by the occurrence and development of cavitation, the obtained unsteady velocity field has been analyzed via Proper Orthogonal Decomposition (POD) technique to identify and understand changes in the flow structure. It has been found that the occurrence and development of cavitation can change the contribution of the POD modes to the total velocity filed. Moreover, the appearance of cavitation seems to stabilize the flow field unsteady behavior since high order POD modes are harmonically correlated with the first couple of basic POD modes., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Numerical investigation of the effects of hydrofoil vibrations on the unsteady behavior of cavitation

  • Geng, Linlin
  • Chen, Jian
  • Torre Rodríguez, Óscar de la
  • Escaler Puigoriol, Francesc Xavier
In order to better understand the fluid-structure interaction (FSI) in hydraulic machines, this study aims to numerically investigate the flow around an oscillating hydrofoil with special attention on the effect of unsteadiness on leading edge cavitation. The cavitating flow has been modelled as incompressible with a Shear Stress Transport (SST) turbulence model coupled with a transition model, and with a mass transport equation between vapor and water. The sinusoidal motion of the hydrofoil has been implemented by using a moving mesh technique. The numerical results, which have been validated with experimental data, show that a critical frequency exists showing two different behaviors. For pitching frequencies above this critical frequency, the cavitation shedding frequency is linearly dependent on the pitching frequency. Moreover, this change of cavitation dynamics is explained by a pressure phase shift and an amplitude change observed as the pitching frequency increases., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Assessment of fiber bragg grating sensors for monitoring induced strains on the draft tube cone of hydraulic turbines

  • Sánchez Botello, Xavier
  • Roig Bauzà, Rafel
  • Torre Rodríguez, Óscar de la
  • Madrigal, Javier
  • Sales, Salvador
  • Mulu, Berhanu
  • Högström, Carl-Maikel
  • Escaler Puigoriol, Francesc Xavier
In hydraulic turbines, several flow instabilities can take place inside the draft tube cone during off-design and transient operating conditions such as the rotating vortex rope which can severely damage the structure if sustained in time. In the frame of the AFC4Hydro H2020 research project, an extensive measurement campaign has been carried out to monitor and predict this rotating vortex rope phenomenon in a reduced scale Kaplan turbine model at the Vattenfall Research and Development facility in Älvkarleby, Sweden. The hydraulic turbine model has been operated in propeller mode with a fixed blade angle corresponding to its best efficiency point. Several sensors have been placed along the test stand to monitor vibrations, strains and pressures. Concretely, the present paper assesses the performance of using Fiber Bragg Grating sensors to measure the strains induced on the draft tube cone walls with high-spatial resolution in three different zones of influence: the upper and lower flanges and the vertical cone wall between the runner outlet and the elbow. To do so, a total of 3 arrays embedding a total of 48 Fiber Bragg Grating sensors were glued inside three grooves previously machined on these particular areas of the draft tube cone. Analysing the frequency response of the different Fiber Bragg Grating sensors, the strain patterns induced by the rotating and plunging components of the rotating vortex rope have been precisely determined. Moreover, their impacts at the different part load conditions tested have also been quantified., This work was supported by the funding received from the European Union’s Horizon H2020 research and innovation program under grant agreement No 814958. The authors would like to acknowledge the technical support received from Vattenfall AB., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Mass transfer rate effects on the cavitating vortex shedding flow around a circular cylinder at low Reynolds number

  • Chen, Jian
  • Escaler Puigoriol, Francesc Xavier
Cavitating vortex shedding is a flow phenomenon commonly encountered behind bluff bodies in hydraulic machinery and systems and the generated vapor bubbles significantly change the dynamic behavior of the vortices. In addition, the collapses of the cavities become a source of unwanted effects such as vibration, noise and material erosion. In this study, the numerical results of the cavitating vortex shedding behind a circular cylinder at low Reynolds number have been compared and analyzed using different mass transfer rate values between the vapor and the liquid water phases. For that, the transport equation for the vapor volume fraction coupled with the explicit source term based on the simplification of the Rayleigh-Plesset equation has been solved. Commonly, this explicit source term that accounts for the mass transfer rate is driven by a function of the pressure difference, the vapor volume fraction and several empirical factors. To understand the effects of this rate, its value has been gradually increased from its default value up to the infinite when the equilibrium assumption for the barotropic flow is satisfied. The obtained results show that as the rate is increased, higher gradients of the vapor volume fraction and of the pressure near the interface between the vapor and the liquid phases are predicted. However, the frequency of the vortex shedding is slightly affected by the increase of the mass transfer rate., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

PZT actuators as on-board instruments to reduce vibrations and strains in submerged structures

  • Sánchez Botello, Xavier
  • Torre Rodríguez, Óscar de la
  • Roig Bauzà, Rafel
  • Costa Castelló, Ramon
  • Escaler Puigoriol, Francesc Xavier
This paper presents the design and evaluation of an active control system to reduce vibrations and strains of submerged structures. For that, a metallic disk mounted in a test rig has been equipped with on-board waterproof strain gauges and accelerometers, to measure its structural response, and with an on-board PZT actuator patch, to provide the required control force. This control force is computed in real-time by an optimal algorithm that determines the exact voltage to be supplied to the PZT patch in order to mitigate any increase of vibrations and/or strains detected by the sensors. In order to capture the dynamics of the structure when it is excited both in air and submerged in water, a plant model has been identified from the Frequency Response Functions (FRFs) obtained experimentally from the measured vibrations and numerically from simulated strains. With these plant models, two different control techniques based on a Linear Quadratic Gaussian (LQG) controller and on an H8 controller have been implemented and simulated under different types of excitations. The obtained results are satisfactory and support the need to continue the research to validate them experimentally., This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 814958., Peer Reviewed, Postprint (published version)