Pasar al contenido principal

MEJORA DE LA COMBUSTION DE CARBON CON CAPTURA DE CO2 POR PROCESOS DE CHEMICAL LOOPING

ENE2013-45454-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2013
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Secretaría de Estado de Educación, Formación Profesional y Universidades
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Comparative evaluation of the performance of coal combustion in 0.5 and 50 kWth Chemical Looping Combustion units with ilmenite, redmud or iron ore as oxygen carrier.

  • Abad Secades, Alberto
  • Mendiara, Teresa
  • Gayán Sanz, Pilar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Bueno, José A.
  • Pérez-Vega, Raúl
  • Adánez Elorza, Juan
13 figures, 2 tables.-- Work presented at the 13th International Conference on Greenhouse Gas Control Technologies, GHGT-13, 14-18 November 2016, Lausanne, Switzerland, Chemical Looping Combustion (CLC) is one of the most promising technologies to achieve the CO2 capture at a low economic and energetic penalty. In CLC the combustion is split in two steps: fuel combustion assisted by an oxygen carrier in the fuel reactor, and oxygen carrier regeneration in the air reactor by oxygen in air. Usually, the air and fuel reactors are interconnected fluidized beds, with the oxygen carrier circulating between them. Thus, the CO2 capture is inherent to the CLC process. The use of solid fuels in CLC is attracting great attention due to coal is the most abundant fuel, and burning biomass with CO2 capture would allow to reduce the atmospheric CO2 concentration. The in situ Gasification CLC (iG-CLC) allows the conversion of the solid fuel by performing both gasification and combustion of gasification products in the fuel reactor. In iG-CLC complete combustion is not reached, and an oxygen polishing step is required downstream by using a small fraction of pure oxygen., The authors thank the Spanish Ministry of Economy and Competitiveness (MINECO) for the funding received from the ENE2013-45454-R and ENE 2014-56857-R projects, as well as the European Regional Development Fund (ERDF)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Evaluation of (MnxFe1-x)2TiyOz particles as oxygen carrier for Chemical Looping Combustion

  • Abián, María
  • Abad Secades, Alberto
  • Izquierdo Pantoja, María Teresa
  • Gayán Sanz, Pilar
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Adánez Elorza, Juan
Work presented at the 13th International Conference on Greenhouse Gas Control Technologies, GHGT-13, 14-18 November 2016, Lausanne, Switzerland., The present work accomplishes a screening of the performance of Mn-Fe-Ti based oxygen carriers, prepared with different Mn/(Mn+Fe) molar ratios in the general formula (MnyFe1-y)Ti0.15Ox. The oxygen carriers were prepared by physical mixing followed by pelletizing under pressure, calcining, crushing and sieving in the 100-300 μm particle size interval. The characterization of the carriers is based on the evaluation of their crushing strength, magnetic properties and reduction and oxidation behavior through TGA experiments at temperatures suitable for the CLC process (i.e. 850-950 °C). In addition, the main chemical structures of the Mn-Fe-Ti system were identified as a function of the Mn/(Mn+Fe) molar ratio. Oxygen uncoupling property was analyzed by reduction under a N2 atmosphere and the capability to interact with fuel gases was analyzed by using CH4, H2 and CO. Results indicate that the (MnyFe1-y)Ti0.15Ox oxygen carriers with Mn/(Mn+Fe) molar ratios of 0.55-0.87 have very promising properties for the CLC process with solid fuels., This work was partially supported by the Spanish Ministry for Economy and competitiveness via the ENE-2013-45454-R project, by the European Regional Development Fund (ERDF) and by the CSIC via the 2014-80E101 project. M. Abian acknowledges the MINECO and Instituto de Carboquimica (ICB-CSIC) for the post-doctoral grant awarded (FPDI-2013-16172), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Design and operation of a coal-fired 50 kWth chemical looping combustor

  • Adánez Elorza, Juan
  • Abad Secades, Alberto
  • Pérez-Vega, Raúl
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Gayán Sanz, Pilar
7 figures, 3 tables.-- Work presented at the 12th International Conference on Greenhouse Gas Control Technologies, GHGT-12, 5th - 9th October 2014, Austin, Texas, (USA), CLC technology with solid fuels is being developed mainly by means of two modes: in situ Gasification CLC (iG-CLC) and Chemical Lopping with Oxygen Uncoupling (CLOU). In the iG-CLC concept, coal gasification is an intermediate step taking place inside the fuel reactor, where gasification products (CO+H2) and volatile matter are oxidized by reaction with oxygen carrier particles. The CLOU concept was developed on the strategy of using oxygen carrier materials which can release gaseous oxygen in the fuel reactor environment, and thereby allowing the solid fuel to be quickly burnt with gas phase oxygen. A 50 kWth pilot plant for solid fuels have been designed and constructed to be operated in both iG-CLC and CLOU modes. The design of the concept was based on two interconnected circulating fluidized beds reactors. The coal is fed at the bottom of the fuel reactor to maximize the contact between the volatile matter and the oxygen carrier particles, minimizing the unburnt compounds at the outlet. In iG-CLC mode, residence time of solids in the fuel reactor is low compared to the time to allow complete coal gasification. A carbon stripper has been included between fuel and air reactors to increase the residence time of char particles in the fuel reactor, thus allowing high CO2 capture rates. In this unit, the char particles are separated from the oxygen carrier particles using their different fluidization properties and they are recirculated to the fuel reactor. This unit could be also required for low reactive coals in CLOU mode. Solids circulation flow rate is controlled by using a double loop seal after fuel reactor cyclone. In this device, the solid flow exiting from the fuel reactor splits into two different streams. One goes to the carbon stripper and the other is recirculated to the fuel reactor., We thank the Spanish Ministry for Science and Innovation for financial support via the ENE2013-45454-R project. R. Pérez-Vega thanks for the FPI Fellowship.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Evaluación de minerales de manganeso como transportadores de oxígeno en la combustión de carbón con captura de CO2 mediante el proceso CLC

  • Mendiara, Teresa
  • Mei, Daofeng
  • Gayán Sanz, Pilar
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
Póster presentado en la XIII Reunión del Grupo Español del Carbón, del 18 al 21 de Octubre de 2015, organizada por la Universidad de Alicante con el apoyo del Grupo Español del Carbón., La tecnología Chemical Looping Combustion (CLC) es una de las técnicas más prometedoras dentro de las opciones de captura de CO2 puesto que permite la combustión de carbón con separación inherente de CO2 con un bajo coste. En esta técnica, el oxígeno necesario es aportado por un transportador de oxígeno, normalmente un óxido metálico (MOy), que transfiere el oxígeno del aire al combustible, evitando el contacto directo entre ellos La selección de un transportador de oxígeno barato es importante en la combustión de carbón puesto que parte del transportador es extraido junto con las cenizas., OBJETIVO: Evaluar el comportamiento de varios minerales de manganeso como transportadores de oxígeno en la combustión de carbón, CONCLUSIÓN: El mineral MnGBHNE se propone para su uso en procesos iG-CLC debido a su elevada capacidad de transporte de oxígeno, elevada reactividad y adecuada resistencia mecánica, Este trabajo ha sido financiado por el Ministerio de Economía y Competitividad (MINECO, ENE 2013-45454-R), por fondos FEDER y por el Gobierno de Aragón (DGA, Ref.T06). T. Mendiara agradece al MINECO el contrato “Ramón y Cajal”., Peer reviewed