Pasar al contenido principal

RECUBRIMIENTOS MULTIFUNCIONALES MODIFICADOS CON AGENTES DE RETROALIMENTACION ACTIVA PARA LA PROTECCION DE ALEACIONES LIGERAS DE INTERES EN AERONAUTICA Y AUTOMOCION

MAT2015-65445-C2-1-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Study of the biocompatibility and corrosion resistance of hydroxyapatite Sol-Gel thin coatings on Ti6Al4V alloy

  • Jiménez Morales, Antonia
  • El Hadad, Amir A.
  • Peón, Eduardo
  • García Galván, Federico
  • Barranco, Violeta
  • Galván Sierra, Juan Carlos
Oral presentation given at the PRiME 2016, held in Honolulu (Hawaii) on October 2-7th, 2016., The aim of this work was to prepare hydroxyapatite thin films (HAp) by a sol-gel method and to study the effect of thermal treatment temperature upon the biocompatibility and corrosion protection of these coatings on Ti6Al4V alloy. The HAp sol was obtained by hydrolysis and condensation of a mixture of triethyl phosphite and calcium nitrate tetrahydrate in stoichiometric amounts (i.e. maintaining a Ca/P ratio of 1.67) adapting a water-based route. The crystallite size and degree of crystallinity of the HAp sol-gel derived coatings strongly depends on the thermal treatment applied. Based on this knowledge, the HAp sol-gel films were annealing in air during 2h at 400ºC, 600ºC, 800ºC and 1200ºC, respectively. As an alternative to conventional thermal treatments, a set of samples was prepared by applying a modification of the Controlled Rate Thermal Analysis (CRTA) developed by Rouquerol, with the aim of obtaining HAp ceramic thin films with controlled textural characteristics at lower temperatures. The basis of this thermal treatment is to control temperature and pressure system, keeping constant the decomposition speed. The application of Thermogravimetric/Differential Thermal Analyses (TG/DTA) and X-ray Diffraction (XRD) has provided valuable information about the phase transformation, mass loss, identification of the phases developed, crystallite size and degree of crystallinity of the obtained HAp powders. Fourier Transformer Infrared Spectroscopy (FTIR) has been utilized for studying the functional groups within the prepared structures. The surface morphology and nature of the prepared HAp coatings was studied by Scanning Electron Microscopy (SEM) with energy dispersive spectroscopy (EDS). The specific surface (BET) and porosity of the material were determined starting from isotherms of adsorption for N2 at a temperature of 77 K. The corrosion protection behaviour of the HAp-coatings/Ti6Al4V in Kokubo¿s Simulated Body Fluid (SBF) has been studied by Electrochemical Impedance Spectroscopy (EIS). Inductively Coupled Plasma (ICP) has been used to detect the concentration of Ca2+ and PO43- ions released and re-precipitated upon the HAp coatings submitted to soaking test in SBF. The quantification of the in vitro cytotoxicity of the HAp sol-gel coatings was made with human osteoblast cultures and a tetrazolium dye (MTT) based assay (3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyltetrazoliumbromide)). Finally the analysis of the adhesion and cellular proliferation on the surface of the materials was also carried out. In these last studies Alamar Blue assays and human osteoblast cultures have been used. In summary hydroxyapatite nano-crystalline coatings on Ti6Al4V alloy have been obtained by a water-based sol-gel route. The crystallite size and degree of crystallinity of the HAp sol-gel derived coatings strongly depends on the thermal treatment applied. HAp films have been successfully obtained by annealing sol-gel-derived coatings in air during 2h at 600ºC and 800ºC. As an alternative to these conventional thermal treatments it has been possible to crystallize pure hydroxyapatite at 100°C of temperature of control for the pressure and 300°C as maximum temperature by applying controlled rate thermal analysis (CRTA) conditions. The obtained results have shown that the prepared coatings are nanocrystalline HAp with little deviations from that present in the human bone. All these HAp coating/Ti6Al4V systems have shown to have good bioactivity upon immersion in SBF, good biocompatibility and corrosion protection properties., The authors would also like to acknowledge the Ministerio de Economía y Competitividad of Spain (Projects MAT2012-38541-C02-02 and MAT2015-65445-C2-1-R) and Comunidad de Madrid (Project S2013/MIT-2862-MULTIMAT-CHALLENGE) for funding this research.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Corrosion protection of metallic substrates of historical interest by lanthanum-silica sol-gel coatings

  • García Galván, Federico
  • Peña Poza, Javier
  • Agua Martínez, Fernando
  • Villegas Broncano, María Ángeles
  • Galván Sierra, Juan Carlos
  • García Heras, Manuel
The European Corrosion Congress – EUROCORR. Applied Science with constant Awareness, September, 9-13 2018, ICE Krakow, Poland., Lanthanum compounds as doping agents in silica based sol-gel coatings can play as environmentally friendly corrosion inhibitors of metallic surfaces of interest in automotive and/or aeronautical industries. In the framework of an interdisciplinary research project the application of lanthanum-silica sol-gel coatings to metallic surfaces of historical interest is being explored for the first time. This contribution presents such application as far as four different metallic substrates are concerned: copper, bronze, lead, and steel. Coatings were prepared from tetraethoxysilane (TEOS) as precursor, distilled water for hydrolysis, absolute ethanol as solvent and HNO3 as catalyst of the hydrolysis. Two types of coatings were formulated: one of them using lanthanum nitrate as doping agent, and another one using lanthanum tri-acetate. Both coatings were deposited upon either common glass slides or metallic plates from 1.0 to 1.5 mm in thickness of copper, bronze, lead, and steel by dip coating at a constant drawing speed (2.0 mm s-1), under controlled temperature (25°C) and relative humidity (35%). Partial thermal densification was accomplished in a forced air stove at 60°C for 72 h. Low quality plates of these four metals and alloys were selected since they are among the most common substrates of metallic items of historical and Heritage interest. Once coatings were made the remaining sols were gelled at 35°C for 48 h. After that, sol-gel monoliths were powdered for characterization by Fourier transformed infrared spectroscopy (FTIR), differential thermal analysis (DTA) and thermogravimetry (TG). A set of sol-gel coating/metal systems was coated with transparent polyvinylbutyral films to simulate commercial top-coatings. Coatings thickness was evaluated by the interference fringe method. The corrosion resistance of both types of lanthanum-silica sol-gel coatings was studied through cathodic delamination tests and electrochemical impedance spectroscopy (EIS) measurements carried out during immersion of coated samples into a 0.6 M NaCl aqueous solution. In addition, chemical and optical quality was also evaluated by weathering and resistance tests. Microstructure was studied by field emission scanning electron microscopy (FESEM). The results indicate that a concentration of 1 mol % of La2O3 respect to the sol-gel coating formulation is adequate for La3+-ions to remain entrapped in the pores and interstitial sites of the silica matrix and thus behave as active corrosion inhibitors that are released when the metal/coating system is set in contact with the aqueous solution. Moreover, the precipitation of insoluble lanthanum products provides a self-healing mechanism which later plays as a protective barrier for the delay of early corrosion. The electrochemical study by joined cathodic delamination tests and EIS has proved to be very effective in evaluating not only the inhibitor effect of lanthanum compounds but also their self-healing properties., Projects ref. MAT2015-65445-C2-1-R and MAT2015-65445-C2-2-R. Program Geomateriales 2 (S2013/MIT 2914 CAM EU) (Dr. J. Peña-Poza contract).