Pasar al contenido principal

MATERIALES TERMOESTABLES AVANZADOS OBTENIDOS MEDIANTE METODOLOGIA CLICK

MAT2017-82849-C2-2-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Sequential photo-thermal curing of (meth)acrylate-epoxy thiol formulations

  • Roig, Adrià
  • Flor López, Sílvia de la|||0000-0002-6851-1371
  • Ramis Juan, Xavier|||0000-0003-2550-7185
  • Serra Albet, Maria Àngels|||0000-0003-1387-0358
In this work, a novel dual-curing procedure has been developed. It is a combination of a first radical UV-initiated thiol-(meth)acrylate reaction, followed by a second thermal thiol-epoxy step catalysed by a base. Since (meth)acrylates can lead to homopolymerization by radical mechanism, the amount of thiol have to be optimized to reach crosslinked materials with Tgs above room temperature and good mechanical performance. It should be considered, that if the amount of thiol is too low, epoxy homopolymerization can take place. The use of glycidyl methacrylate in combination with trifunctional meth(acrylates) allow this system to gel in the 1st stage and avoid possible dripping or exudation of free monomers in the storage of the intermediate materials. We selected trimethylolpropane tris(3-mercaptopropionate) as the thiol, 2,2-dimethoxy-2- phenylacetophenone as UV initiator and 1-methylimidazole as the base catalyst, Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Novel hybrid poly(thiourethane)/POSS covalent adaptable networks

  • Guerrero, Federico
  • Flor López, Sílvia de la|||0000-0002-6851-1371
  • Ramis Juan, Xavier|||0000-0003-2550-7185
  • Santos, Jose-Ignacio
  • Serra Albet, Maria Àngels|||0000-0003-1387-0358
Hybrid organic-inorganic materials have been introduced as one of the strategies to improve mechanical properties and obtaining new high-performance polymeric materials. These materials present a synergism that meets the advantages of both organic and inorganic phases: hardness and strength of inorganic phase, and elasticity and toughness of the organic matrix [1] Thiols and isocyanate groups react to give thiourethane or thiocarbamate groups. Polythiourethane (PTUs) are analogous with sulphur of polyurethane (PUs), one of the most produced polymers in the world. Despite of their advantages over PUs, PTUs have been less studied than PUs. In previous studies of our group, it was demonstrated that trans-thiocarbamoylation exchange reactions between thiourethane groups leads to a vitrimeric-like behaviour to this knd of networked polymers improving the easily of recycling and reshaping them [2, 3]. The aim of this study is not only to improve the mechanical characteristics of PTUs but also to determine the effect of the inorganic reinforcement in the relaxation behaviour., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Contribución de congreso (ConferenceOutput)

Dual-curable vitrimers for 3d-printing

  • Romano, Angelo
  • Konuray, Ali Osman|||0000-0001-7281-006X
  • Roppolo, Ignazio
  • Sangermano, Marco
  • Fernández-Francos, Xavier
  • Ramis Juan, Xavier|||0000-0003-2550-7185
3D-printed objects can greatly benefit from the introduction of molecular structure undergoing dynamic bond exchange [1] or the use dual-curing processing [2], leading to a significant enhancement of mechanical properties and extended capabilities such as adhesion, reshaping, healing and recycling. We have developed a family of dual-curing 3D-printable materials based on acrylate homopolymerization for the printing stage and epoxy-acid reaction for the second thermal curing stage, with the purpose 1) having a stable intermediate material with desired reshaping and adhesion capabilities and 2) obtaining a network structure capable of undergoing dynamic work rearrangement promoted by transesterification between ester and available hydroxyl groups. A latent amine catalyst has been added in order to accelerate both the thermal curing stage and transesterification, Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Novel hybrid poly(thiourethane)/POSS covalent adaptable networks

  • Guerrero, Federico
  • Flor López, Sílvia de la
  • Ramis Juan, Xavier
  • Santos, Jose-Ignacio
  • Serra Albet, Maria Àngels
Hybrid organic-inorganic materials have been introduced as one of the strategies to improve mechanical properties and obtaining new high-performance polymeric materials. These materials present a synergism that meets the advantages of both organic and inorganic phases: hardness and strength of inorganic phase, and elasticity and toughness of the organic matrix [1] Thiols and isocyanate groups react to give thiourethane or thiocarbamate groups. Polythiourethane (PTUs) are analogous with sulphur of polyurethane (PUs), one of the most produced polymers in the world. Despite of their advantages over PUs, PTUs have been less studied than PUs. In previous studies of our group, it was demonstrated that trans-thiocarbamoylation exchange reactions between thiourethane groups leads to a vitrimeric-like behaviour to this knd of networked polymers improving the easily of recycling and reshaping them [2, 3]. The aim of this study is not only to improve the mechanical characteristics of PTUs but also to determine the effect of the inorganic reinforcement in the relaxation behaviour., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Sequential photo-thermal curing of (meth)acrylate-epoxy thiol formulations

  • Roig, Adrià
  • Flor López, Sílvia de la
  • Ramis Juan, Xavier
  • Serra Albet, Maria Àngels
In this work, a novel dual-curing procedure has been developed. It is a combination of a first radical UV-initiated thiol-(meth)acrylate reaction, followed by a second thermal thiol-epoxy step catalysed by a base. Since (meth)acrylates can lead to homopolymerization by radical mechanism, the amount of thiol have to be optimized to reach crosslinked materials with Tgs above room temperature and good mechanical performance. It should be considered, that if the amount of thiol is too low, epoxy homopolymerization can take place. The use of glycidyl methacrylate in combination with trifunctional meth(acrylates) allow this system to gel in the 1st stage and avoid possible dripping or exudation of free monomers in the storage of the intermediate materials. We selected trimethylolpropane tris(3-mercaptopropionate) as the thiol, 2,2-dimethoxy-2- phenylacetophenone as UV initiator and 1-methylimidazole as the base catalyst, Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Dual-curable vitrimers for 3d-printing

  • Romano, Angelo
  • Konuray, Ali Osman
  • Roppolo, Ignazio
  • Sangermano, Marco
  • Fernández-Francos, Xavier
  • Ramis Juan, Xavier
3D-printed objects can greatly benefit from the introduction of molecular structure undergoing dynamic bond exchange [1] or the use dual-curing processing [2], leading to a significant enhancement of mechanical properties and extended capabilities such as adhesion, reshaping, healing and recycling. We have developed a family of dual-curing 3D-printable materials based on acrylate homopolymerization for the printing stage and epoxy-acid reaction for the second thermal curing stage, with the purpose 1) having a stable intermediate material with desired reshaping and adhesion capabilities and 2) obtaining a network structure capable of undergoing dynamic work rearrangement promoted by transesterification between ester and available hydroxyl groups. A latent amine catalyst has been added in order to accelerate both the thermal curing stage and transesterification, Peer Reviewed, Postprint (author's final draft)