- Fernández Domene, Ramón Manuel
- Solsona Espriu, Benjamin Eduardo
- Erans Moreno, María
- Blasco-Tamarit, E.|||0000-0001-7314-082X
- Sánchez Tovar, Rita
This study reports the bio-mediated synthesis of tungsten trioxide nanostructures from aqueous extracts of Melia
azedarach (L.) dry leaves. The synthesis was carried out by electrochemical anodization of tungsten foils in the
presence of different volume percentages of leaves extracts. These nanostructures were afterwards
characterized by X-Ray Diffraction (XRD), impedance measurements and linear sweep voltammetry
in the presence of simulated solar light. Finally, these nanoelectrodes were used as
(photo)electrocatalysts in the photoelectrochemical water splitting process to obtain green hydrogen and as
anodes in Li-ion rechargeable batteries.
Description of methods used for collection/generation of data:
- Synthesis of WO3 nanostructures:
The leaves of M. azedarach were randomly sampled from several
mature trees from the surroundings of the Burjassot Campus of the
University of Valencia (Spain). Fresh leaves were rinsed with tap and
distilled water and subsequently air-dried indoors for 1 week, at room
temperature. The extracts were obtained from dried leaves, by mixing
15 g of material with 150 mL of distilled water at 60 ºC. The infusion was
maintained at that temperature for 20 min. After that, the solution, once
cooled, was filtered through filter paper and used to prepare the
different reaction media.
Nanostructures of WO3 were synthesized by subjecting tungsten foils
(1,3 cm2 of exposed area) to an anodization process with a cell potential
of 20 V, for 4 h. A platinum foil served as the cathode within the cell. The
anodization process employed an aqueous electrolyte composed of
1.5 M methanesulfonic acid (MSA) with varying proportions of M.
azedarach leaves extract (from 0% to 10%, in volume), at a temperature
of 50◦C. Anodization was performed under
controlled hydrodynamic conditions, by means of a Rotating Disk
Electrode (RDE) set a constant rotation speed of 750 rpm. Following
anodization, a thermal treatment (annealing) was carried out in a
tubular oven at 600◦C for 4 h in an air atmosphere to obtain crystalline
WO3 nanostructures.
- Morphological and structural characterization:
X-Ray diffraction analyses (XRD) were performed to investigate the
crystallinity of the WO3 samples. A D8AVANCE diffractometer (Bruker)
equipped with a monochromatic Cu Kα1 source was used.
-(Photo)electrochemical characterization: impedance measurements
and photocurrent density vs potential curves:
Electrochemical characterization of the WO3 nanostructures was
conducted through impedance measurements, performing Electrochemical
Impedance Spectroscopy (EIS) and Mott-Schottky (MS) analyses.
All electrochemical tests were carried out using a three-electrode
cell with the nanostructures acting as working electrodes, a silver/silver
chloride (3 M KCl) electrode was the reference electrode and a platinum
tip served as counterelectrode. Measurements were performed with a
PalmSens4 potentiostat and 0.1 M H2SO4 was used as electrolyte. The
sample area exposed to that electrolyte was 0.5 cm2. For EIS, a constant
potential of 1 V was selected with an amplitude of 10 mV, scanning the
frequency from 100 kHz to 10 mHz. For MS analysis, a constant frequency
of 5 kHz was used, while the potential was scanned from 1 V to
0.2 V at a rate of 50 mV/s.
For the photoelectrochemical characterization of the WO3 nanostructures,
the same experimental set-up was used, with the addition of a
solar simulator with AM 1.5 conditions (100 mW/cm2). Linear voltammetries
to obtain photocurrent density – potential curves were
conducted from 0.2 V to 1.05 V, by applying dark-light pulses (16 s in
the dark followed by 4 s with illumination) while the potential was
scanned.
- Evaluation of WO3 nanostructures as Li-ion battery anodes:
WO3 nanostructures were evaluated as anodes (negative electrodes)
for Li-ion batteries. For that purpose, Swagelok-type cells were used,
with WO3 nanostructures acting as working electrodes and a metallic
lithium foil acting as both the counter and the reference electrodes.
Batteries were assembled inside an Ar-filled glove box, using 1 M LiPF6
in ethylene carbonate/dimethyl carbonate/diethyl carbonate 1:1:1 (v/
v/v) as electrolyte (Sigma-Aldrich) and a Whatman glass microfiber
separator. After sealing the cells, they were cycled outside the glove box
at room temperature, using a Biologic BCS-815 cyclic station. Galvanostatic
charge/discharge curves were recorded at different cycling
rates (from C/10–1 C, and returning to C/10) within a potential window
between 1 V and 3.5 V vs Li/Li+.