Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Drone-based RGB, thermal, and multispectral datasets for application with MosaicSeadron

  • Román, Alejandro
  • Heredia, Sergio
  • Windle, Anna E.
  • Tovar-Sánchez, Antonio
  • Navarro, Gabriel
[Description of methods used for collection/generation of data] Three different drones were used for data acquisition, equipped with different sensors: i) The quadcopter DJI Matrice 300 (M300) is equipped with both the MicaSense RedEdge-MX dual multispectral sensor and the DJI Zenmuse H20T sensor. The multispectral sensor has ten bands that capture information from the visible to near-infrared (NIR) range, with wavelengths centered, respectively, at the blue (444 and 475 nm), green (531 and 560 nm), red (650 and 668 nm), red edge (705, 717 and 740 nm), and NIR (842 nm) regions. In addition, it includes a Downwelling Light Sensor (DLS2) to account for changes in solar angle and illumination during flight. A calibration panel (RP04-1924106-0B) was used before each UAV flight for radiometric calibration. The DJI Zenmuse H20T sensor includes a 20-megapixel (MP) optical RGB Zoom sensor with a complementary metal oxide semiconductor (CMOS) 1/2.7″, a 12 MP optical RGB wide angle sensor with a CMOS 1/2.3″, and an Uncooled VOx Microbolometer thermal sensor with a focal length of 13.5 mm, capturing 640 × 512 pixel image resolution. The M300 has on-board real-time kinematic (RTK) technology to enhance georeferencing accuracy, achieving 1 cm ± 1 ppm (horizontal) and 1.5 cm ± 1 ppm (vertical) accuracies when RTK is enabled and fixed. ii) The DJI Phantom 4 Pro (P4P) is equipped with the MicaSense RedEdge-MX sensor, including five bands on the electromagnetic spectrum, namely, in the blue (475 nm), green (560 nm), red (668 nm), red edge (717 nm), and NIR (842 nm) regions. This sensor also includes the DLS and is mounted using a 10° 3D-printed mount, resulting in a direct nadir viewing angle while in flight. The P4P does not have RTK technology on board, so the vertical and horizontal georeferencing accuracies are ±0.1 m and ±0.3 m (with vision positioning) and ±0.5 m and ±1.5 m (with GPS positioning), respectively. iii) The DJI Mavic 2 Enterprise Advanced (M2EA) is equipped with an extra RTK module to ensure accurate georeferencing. It features a 48 MP, 1/2″ CMOS optical RGB sensor and a 640 × 512 px Uncooled VOx Microbolometer thermal sensor. This RTK quadcopter achieves a horizontal accuracy of 1 cm ± 1 ppm and a vertical accuracy of 1.5 cm ± 1 ppm, without the requirement of ground control points (GCPs)., [Environmental/experimental conditions] Data acquisition was attempted to be carried out during spring tide and clear sky weather conditions. In the vast majority of study areas, this was possible except in the Antarctic locations where cloudiness and wind conditions prevailed during the sampling days. In the flights conducted over the San Pedro River and Estepona, strong winds also hindered the execution of the intended UAV surveys. Flight missions were planned using the Universal Ground Control System (UgCS) client mission planning software (SPH Engineering, Riga, Latvia, v.4.2.156) and Pix4D Capture Pro software (Pix4D SA, Lausanne, Switzerland, v.4.12), taking into account different overlapping settings, altitudes, and flight orientations, which are displayed in Table 1 along with the dates of drone survey execution. To support RTK measurements and improve georeferencing accuracies, a Reach RS2+ RTK GNSS antenna (EMLID) was set as the base station for all drone surveys. Spanish (Spanish Agency for Aviation Safety, AESA), European (European Agency for Aviation Safety, EASA), and U.S. (Federal Aviation Administration, FAA) civil aviation regulations were followed during all UAV operations., This repository contains the original RAW data captured by a drone equipped with RGB, thermal, and multispectral sensors, which were used to obtain the results published in Román et al. 2024 (DOI: https://doi.org/10.3390/rs16020290). The repository also aims to make drone‑acquired datasets from various regions of the world - namely Antarctica, southern Europe, and the United States - readily available for running the pioneering georeferencing and mosaicking algorithm "MosaicSeadron" (https://github.com/SeadroneICMAN/MosaicSeadron/). This open‑source Python algorithm overcomes the main limitations of traditional photogrammetric techniques when working with drones over water surfaces. Indeed, it represents a significant advance in monitoring marine and coastal processes by introducing an innovative, efficient, and accurate workflow that improves local‑scale remote observation of aquatic environments., This research has been funded by the European Union’s Horizon 2020 research and innovation programme REWRITE project (grant number 101081357), PY20-00244 (SAT4ALGAE) PROJECT and TURISDRON (PROYEXCEL 00052) project by Junta de Andalucía, RTI2018-098048B-100 (PiMetAn), PID2021-1257830B-100 (DICHOSO), and EQC2018-004275-P and TED2021-129230B-I00 funded by MCIN/AEI/10.13039/501100011033 and by ‘ERDF A way of making Europe’. The research that led to this publication was conducted with the support of a US–Spain Fulbright grant and of the Junta de Andalucía. A.R. is supported by grant FPU19/04557 funded by Ministry of Universities of the Spanish Government. This research has been financially supported by the agreement between the Spanish Ministry for Ecological Transition and Demographic Challenge and CSIC, funded by the European Union-Next Generation Program to contribute to the MSFD. This work represents a contribution to CSIC Thematic Interdisciplinary Platform PTI TELEDETECT., File List: 6 folders: Dataset 1 - San Pedro river_20230621; Dataset 2 - San Pedro river_20230724; Dataset 3 - Estepona_20230128; Dataset 4 - Guadalquivir river_20230322; Dataset 5 - Whalers Bay_20220130; Dataset 6 - Fumarole Bay_20220201, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Drone-derived datasets in the assessment of the 2024 cut-off low event in Valencia

  • Román, Alejandro
  • Tovar-Sánchez, Antonio
  • Larrad, Marcos
  • Rubiano, Francisco
  • Zafra González, José Manuel
  • Piñeiro Martínez de Lecea, Rafael
  • Castillo Talavera, Ángel
  • López Gómez, Félix Antonio
  • Lucía Vela, Ana
  • Allende, Ana
  • Sánchez, Gloria
  • Martínez-Alonso, Alberto
  • Samper, Daniel
  • García López-Davalillo, Juan Carlos
  • Galindo Jiménez, Inés
  • Navarro, Gabriel
[Description of methods used for collection/generation of data] Three different UAV platforms were used for data acquisition, each chosen based on their payload capacity and compatibility with various sensors:: 1) DJI Matrice 300 RTK (M300). This quadcopter supports a maximum payload of 2.5 kg and has a maximum take-off weight (MTOW) of 9 kg. It was equipped with several sensors to capture multispectral imagery, RGB data, and gas concentration measurements: - DJI Zenmuse H20T. A multi-sensor payload featuring a 20 MP RGB zoom camera (1/2.7” CMOS) and a 12 MP wide-angle RGB camera (1/2.3” CMOS). It includes a detachable gimbal and offers a maximum shutter speed of 1/8000 s. Under controlled conditions, the manufacturer specifies an accuracy of 0.2 m plus 0.15% of the target distance. - MicaSense RedEdge-MX. A multispectral dual sensor that captures 10 bands across the visible and near-infrared (NIR) spectrum, including blue (444, 475 nm), green (531, 560 nm), red (650, 668 nm), red edge (705, 717, 740 nm), and NIR (842 nm). The system integrates a Downwelling Light Sensor (DLS) with GPS to account for changes in solar irradiance, along with a radiometric calibration panel (RP04-1924106-0B) to ensure radiometric accuracy. - Sniffer4D V2 RS (Soarability). A multi-gas sensing and mapping system capable of simultaneously detecting total volatile organic compounds (TVOC, ppm), sulfur dioxide (SO₂, μg/m³), ozone and nitrogen dioxide (O₃ + NO₂, μg/m³), particulate matter (PM1.0, PM2.5, PM10, μg/m³), flammable gases (CxHy, %), and hydrogen sulfide (H₂S, μg/m³). It provides real-time visualization in both 2D and 3D. In addition, it was integrated with the Sniffer4D Multi-pass TDLAS Hyper-local Methane Module, enabling quantitative methane detection with a resolution of 1 ppm. 2) DJI Mavic 3E (M3E). A lightweight quadcopter equipped with a 20 MP wide-angle RGB camera (4/3” CMOS) and a 12 MP telephoto RGB camera with 56× hybrid zoom. It has an MTOW of 1,050 g and a maximum flight endurance of 45 minutes. 3) DJI Mavic 2 Enterprise Advanced (M2EA). This UAV features a 48 MP RGB optical sensor with a 1/2” CMOS sensor. It has an MTOW of 1,100 g and a maximum flight duration of 31 minutes., [Methods for processing the data] 1) Structure from Motion (SfM) photogrammetry: Aerial images acquired along pre-programmed flight paths with sufficient overlap were processed using Pix4D Mapper (Pix4D SA, Lausanne, Switzerland, v.4.8.3) to generate high-resolution topographic products. The workflow consisted of image alignment, point cloud generation, digital surface model (DSM) reconstruction, orthomosaic and reflectance maps generation. 2) Gas Sniffer data monitoring: The gas detection sensors were directly connected to the PSDK port of the DJI M300, which provided power and allowed real-time data transmission to the UAV’s remote controller. Measurements were logged at one-second intervals and simultaneously stored on the sensor’s internal SD card. To ensure stable sampling, the device incorporated a rear-mounted active air intake fan, drawing ambient air at a flow rate of roughly 10 L min⁻¹., [Environmental/experimental conditions] UAV flights were conducted in strict accordance with Spanish civil aviation regulations for emergency operations, under the supervision of the Spanish Aviation Safety Agency (AESA). Moreover, missions carried out following the Valencia cut-off low were undertaken within the framework of the Scientific-Technical Advisory Group for Emergency Crises (GADE) of the Spanish National Research Council (CSIC). For field operations, flight plans were pre-programmed using the DJI Pilot application (Shenzhen Dà-Jiang Innovations Sciences and Technologies Ltd., Guangdong, China) installed on the UAV controller. These plans were configured with fixed parameters, including flight altitude, speed, duration, ground sampling distance (GSD), and image overlap., This repository contains the original raw data, along with some of the topographic products generated after the initial data processing, captured immediately after the 2024 Valencia cut-off low event by a drone equipped with RGB, thermal, multispectral, and gas-sniffer sensors. These datasets were used to obtain the results published in Román et al. 2025 (DOI: available soon). The data, together with their rapid and preliminary processing, were also employed in real time during the emergency to support decision-makers in tasks related to prevention, evacuation, and reconstruction. Furthermore, access to these data makes the methodologies described in the manuscript reproducible, thereby contributing to the development of new tools that can enable faster, more efficient, and more accurate management during future emergencies., This work was financially supported by funds from PIE202430E238 and PIE202460E236. Sensors and UAV were funded by Spanish Government Infrastructure Project EQC2018-004275-P and EQC2019-005721. The Accreditation of IATA as a Center of Excellence, Severo Ochoa CEX2021-001189-S funded by MCIU/AEI/10.13039/501100011033 is fully acknowledged. A. Román, staff hired under the Generation D initiative, promoted by Red.es, an organisation attached to the Ministry for Digital Transformation and the Civil Service, for the attraction and retention of talent through grants and training contracts, financed by the Recovery, Transformation and Resilience Plan through the European Union's Next Generation funds. This study also represents a contribution to the CSIC Scientific-Technical Advisory Group for Emergency Crises (GADE-CSIC, Spain)., With funding form the Spanish government through the "Severa Ochoa Centre of Excellence" accreditation (CEX2021-001189-S)., File List: 6 folders: Dataset 1 - Object Detection Vehicle Yard; Dataset 2 - Object Detection Trash Items; Dataset 3 - Gas Sensors Paiporta; Dataset 4 - Damage Assessment Picanya; Dataset 5 - Damage Assessment Pont Nou; Dataset 6 - Sludge Characterization, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Post-fire UAV LiDAR dataset of the Las Médulas Cultural Heritage Site (León, Spain)

  • Navarro, Gabriel
  • García López-Davalillo, Juan Carlos
  • Pecharromán Fuente, Juan Luis
  • Tovar-Sánchez, Antonio
  • Gumiel, Juan Carlos
  • Madrigal, Javier
  • Galindo Jiménez, Inés
  • Román, Alejandro
[Description of methods used for collection/generation of data A total of 37 UAV flights were conducted using DJI Matrice 300/350 platforms equipped with Zenmuse L1 and L2 LiDAR sensors. Terrain-following acquisition was performed at 120 m AGL using double-grid flight plans., [Methods for processing the data] Data were processed in DJI Terra v5.1.0 to generate LAS point clouds, DEM, DSM, and DOM. Output rasters and clouds were tiled (1×1 km or 2×2 km) using Python scripts (included)., This dataset contains high-resolution UAV-LiDAR data acquired in September and November 2025 following the Yeres wildfire affecting the Las Médulas Cultural Heritage Site (León, Spain). Las Médulas is a UNESCO World Heritage landscape shaped by large-scale Roman gold mining, making precise post-fire documentation essential for archaeological, geomorphological, and environmental assessment. The dataset includes LiDAR point clouds, Digital Elevation Models (DEM), Digital Surface Models (DSM), and orthomosaics (DOM) produced for the full extent of the BIC. These open-access data provide an unprecedented 3D record of post-fire terrain conditions, vegetation loss, and erosion patterns, supporting heritage management, ecological monitoring, and scientific research., This research was funded by the CSIC Scientific-Technical Advisory Group for Emergency Crises (GADE-CSIC, Spain) and partially by PIE202430E238. ICMAN sensors and UAVs were funded by Spanish Government Infrastructure Project EQC2018–004275-P and SCT-OPECAM (825909). IGME sensors and UAVs were partially founded by MICIU/AEI/10.13039/501100011033/FEDER, UE in CPP2023-010560 HELICE project. A. Román, staff hired under the Generation D initiative, promoted by Red.es, an organisation attached to the Ministry for Digital Transformation and the Civil Service, for the attraction and retention of talent through grants and training contracts, financed by the Recovery, Transformation and Resilience Plan through the European Union’s Next Generation funds., File List: /DEM_2x2km/ — Digital Elevation Model tiles (GeoTIFF) /DSM_2x2km/ — Digital Surface Model tiles (GeoTIFF) /DOM_1x1km/ — Orthomosaic tiles (GeoTIFF) /LAS_1x1km/ — LiDAR point cloud tiles (LAS format), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Original raw datasets of greenhouse gas concentrations measured using a LI-COR LI-7810 gas analyser in penguin colonies, and topographic products generated from drone-based surveys

  • Román, Alejandro
  • Amaya-Vías, Silvia
  • Díez-Minguito, Manuel
  • Tovar-Sánchez, Antonio
  • Navarro, Gabriel
  • Flecha, Susana
  • Huertas, I. Emma
This repository contains the original raw data acquired with the LI-COR LI-7810 gas analyser, together with some of the topographic products generated during the initial processing of drone-derived RGB and multispectral data, from which the results reported in the publication “Methane emissions from penguin colonies reshape the natural greenhouse gas budget” were derived. In parallel, in-situ measurements of methane, carbon dioxide, and water were collected using a gas analyser and non-steady-state chambers at multiple georeferenced locations across two major Chinstrap penguin colonies on Deception Island (South Shetland Islands, Antarctica). Drone-based observations were simultaneously acquired to analyse the spatial distribution of individuals within the colonies and characterize their surrounding ecosystem. The results of this study demonstrate that dense aggregations of Chinstrap penguins represent an overlooked component of the natural CH4 cycle in Antarctica and highlight the need to better constrain these emissions in future CH4 budgets., This research was supported by the projects DICHOSO (PID2021-1257830B-100) and SYMPHONIA (PIE202630E144) funded by the Spanish Ministry of Science, Innovation and Universities and the CSIC, respectively. Sensors and UAVs were funded by the grants EQC2018-004275-P and EQC2019-005721. A. Román and S. Flecha, staff hired under the Generation D initiative, promoted by Red.es, an organisation attached to the Ministry for Digital Transformation and the Civil Service, for the attraction and retention of talent through grants and training contracts, financed by the Recovery, Transformation and Resilience Plan through the European Union’s Next Generation funds., Peer reviewed