Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Visual guidance of unmanned aerial manipulators

  • Santamaria-Navarro, Àngel
A thesis submitted to the Universitat Politècnica de Catalunya for the degree of Doctor of Philosophy. Doctoral Programme: Automatic Control, Robotics and Computer Vision. This thesis has been completed at: Institut de Robòtica i Informàtica Industrial, CSIC-UPC., [EN]: The ability to fly has greatly expanded the possibilities for robots to perform surveillance, inspection or map generation tasks. Yet it was only in recent years that research in aerial robotics was mature enough to allow active interactions with the environment. The robots responsible for these interactions are called aerial manipulators and usually combine a multirotor platform and one or more robotic arms. The main objective of this thesis is to formalize the concept of aerial manipulator and present guidance methods, using visual information, to provide them with autonomous functionalities. A key competence to control an aerial manipulator is the ability to localize it in the environment. Traditionally, this localization has required external infrastructure of sensors (e.g., GPS or IR cameras), restricting the real applications. Furthermore, localization methods with on-board sensors, exported from other robotics fields such as simultaneous localization and mapping (SLAM), require large computational units becoming a handicap in vehicles where size, load, and power consumption are important restrictions. In this regard, this thesis proposes a method to estimate the state of the vehicle (i.e., position, orientation, velocity and acceleration) by means of on-board, low-cost, light-weight and high-rate sensors. With the physical complexity of these robots, it is required to use advanced control techniques during navigation. Thanks to their redundancy on degrees-of-freedom, they offer the possibility to accomplish not only with mobility requirements but with other tasks simultaneously and hierarchically, prioritizing them depending on their impact to the overall mission success. In this work we present such control laws and define a number of these tasks to drive the vehicle using visual information, guarantee the robot integrity during flight, and improve the platform stability or increase arm operability. The main contributions of this research work are threefold: (1) Present a localization technique to allow autonomous navigation, this method is specifically designed for aerial platforms with size, load and computational burden restrictions. (2) Obtain control commands to drive the vehicle using visual information (visual servo). (3) Integrate the visual servo commands into a hierarchical control law by exploiting the redundancy of the robot to accomplish secondary tasks during flight. These tasks are specific for aerial manipulators and they are also provided. All the techniques presented in this document have been validated throughout extensive experimentation with real robotic platforms., [CA]: La capacitat de volar ha incrementat molt les possibilitats dels robots per a realitzar tasques de vigilància, inspecció o generació de mapes. Tot i això, no és fins fa pocs anys que la recerca en robòtica aèria ha estat prou madura com per començar a permetre interaccions amb l’entorn d’una manera activa. Els robots per a fer-ho s’anomenen manipuladors aeris i habitualment combinen una plataforma multirotor i un braç robòtic. L’objectiu d’aquesta tesi és formalitzar el concepte de manipulador aeri i presentar mètodes de guiatge, utilitzant informació visual, per dotar d’autonomia aquest tipus de vehicles. Una competència clau per controlar un manipulador aeri és la capacitat de localitzar-se en l’entorn. Tradicionalment aquesta localització ha requerit d’infraestructura sensorial externa (GPS, càmeres IR, etc.), limitant així les aplicacions reals. Pel contrari, sistemes de localització exportats d’altres camps de la robòtica basats en sensors a bord, com per exemple mètodes de localització i mapejat simultànis (SLAM), requereixen de gran capacitat de còmput, característica que penalitza molt en vehicles on la mida, pes i consum elèctric son grans restriccions. En aquest sentit, aquesta tesi proposa un mètode d’estimació d’estat del robot (posició, velocitat, orientació i acceleració) a partir de sensors instal·lats a bord, de baix cost, baix consum computacional i que proporcionen mesures a alta freqüència. Degut a la complexitat física d’aquests robots, és necessari l’ús de tècniques de control avançades. Gràcies a la seva redundància de graus de llibertat, aquests robots ens ofereixen la possibilitat de complir amb els requeriments de mobilitat i, simultàniament, realitzar tasques de manera jeràrquica, ordenant-les segons l’impacte en l’acompliment de la missió. En aquest treball es presenten aquestes lleis de control, juntament amb la descripció de tasques per tal de guiar visualment el vehicle, garantir la integritat del robot durant el vol, millorar de l’estabilitat del vehicle o augmentar la manipulabilitat del braç. Aquesta tesi es centra en tres aspectes fonamentals: (1) Presentar una tècnica de localització per dotar d’autonomia el robot. Aquest mètode està especialment dissenyat per a plataformes amb restriccions de capacitat computacional, mida i pes. (2) Obtenir les comandes de control necessàries per guiar el vehicle a partir d’informació visual. (3) Integrar aquestes accions dins una estructura de control jeràrquica utilitzant la redundància del robot per complir altres tasques durant el vol. Aquestes tasques son específiques per a manipuladors aeris i també es defineixen en aquest document. Totes les tècniques presentades en aquesta tesi han estat avaluades de manera experimental amb plataformes robòtiques reals., This work has been partially supported by an FPI-UPC grant (87-915) of the Universitat Politècnica de Catalunya under the EU project ARCAS (FP7-ICT-287617), and also funded from the EU project AEROARMS (H2020-ICT-2014-1-644271), Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Bridging the gap between reconstruction and synthesis

  • Pumarola, Albert
Tesis doctoral presentada para lograr el título de Doctor por la Universidad Politécnica de Cataluña, programa de doctorado: Automatic Control, Robotics and Computer Vision.--2021-10-13, [EN] 3D reconstruction and image synthesis are two of the main pillars in computer vision. Early works focused on simple tasks such as multi-view reconstruction and texture synthesis. With the spur of Deep Learning, the field has rapidly progressed, making it possible to achieve more complex and high level tasks. For example, the 3D reconstruction results of traditional multi-view approaches are currently obtained with single view methods. Similarly, early pattern based texture synthesis works have resulted in techniques that allow generating novel high-resolution images. In this thesis we have developed a hierarchy of tools that cover all these range of problems, lying at the intersection of computer vision, graphics and machine learning. We tackle the problem of 3D reconstruction and synthesis in the wild. Importantly, we advocate for a paradigm in which not everything should be learned. Instead of applying Deep Learning naively we propose novel representations, layers and architectures that directly embed prior 3D geometric knowledge for the task of 3D reconstruction and synthesis. We apply these techniques to problems including scene/person reconstruction and photo-realistic rendering. We first address methods to reconstruct a scene and the clothed people in it while estimating the camera position. Then, we tackle image and video synthesis for clothed people in the wild. Finally, we bridge the gap between reconstruction and synthesis under the umbrella of a unique novel formulation. Extensive experiments conducted along this thesis show that the proposed techniques improve the performance of Deep Learning models in terms of the quality of the reconstructed 3D shapes / synthesised images, while reducing the amount of supervision and training data required to train them. In summary, we provide a variety of low, mid and high level algorithms that can be used to incorporate prior knowledge into different stages of the Deep Learning pipeline and improve performance in tasks of 3D reconstruction and image synthesis., [CAT] La reconstrucció 3D i la síntesi d'imatges són dos dels pilars fonamentals en visió per computador. Els estudis previs es centren en tasques senzilles com la reconstrucció amb informació multi-càmera i la síntesi de textures. Amb l'aparició del "Deep Learning", aquest camp ha progressat ràpidament, fent possible assolir tasques molt més complexes. Per exemple, per obtenir una reconstrucció 3D, tradicionalment s'utilitzaven mètodes multi-càmera, en canvi ara, es poden obtenir a partir d'una sola imatge. De la mateixa manera, els primers treballs de síntesi de textures basats en patrons han donat lloc a tècniques que permeten generar noves imatges completes en alta resolució. En aquesta tesi, hem desenvolupat una sèrie d'eines que cobreixen tot aquest ventall de problemes, situats en la intersecció entre la visió per computador, els gràfics i l'aprenentatge automàtic. Abordem el problema de la reconstrucció i la síntesi 3D en el món real. És important destacar que defensem un paradigma on no tot s'ha d'aprendre. Enlloc d'aplicar el "Deep Learning" de forma naïve, proposem representacions novedoses i arquitectures que incorporen directament els coneixements geomètrics ja existents per a aconseguir la reconstrucció 3D i la síntesi d'imatges. Nosaltres apliquem aquestes tècniques a problemes com ara la reconstrucció d'escenes/persones i a la renderització d'imatges fotorealistes. Primer abordem els mètodes per reconstruir una escena, les persones vestides que hi ha i la posició de la càmera. A continuació, abordem la síntesi d'imatges i vídeos de persones vestides en situacions quotidianes. I finalment, aconseguim, a través d'una nova formulació única, connectar la reconstrucció amb la síntesi. Els experiments realitzats al llarg d'aquesta tesi demostren que les tècniques proposades milloren el rendiment dels models de "Deepp Learning" pel que fa a la qualitat de les reconstruccions i les imatges sintetitzades alhora que redueixen la quantitat de dades necessàries per entrenar-los. En resum, proporcionem una varietat d'algoritmes de baix, mitjà i alt nivell que es poden utilitzar per incorporar els coneixements previs a les diferents etapes del "Deep Learning" i millorar el rendiment en tasques de reconstrucció 3D i síntesi d'imatges., This work has been partially supported by: - EU project AEROARMS - Aerial Robotics Inspection System, 2015-2019. Code: H2020-ICT-2014- 1-644271 - National Project ColRobTransp - Robotics Last Mile Transportation in Urban Areas, 2016-2019. Code: DPI2016-78957-R - Google Research Award - Geometry-aware CNNs for Non-Rigid Reconstruction, 2017-2018 - Amazon Research Award - Geometry-aware 3D Human Body Animation from Still Photos, 2018- 2019 - Google Research Award - GANimation3D: Unsupervised 3D Face Animation from Monocular Images, 2019-2020
UPCommons. Portal del coneixement obert de la UPC
Publicación Tesis doctoral (DoctoralThesis)

Visual guidance of unmanned aerial manipulators

  • Santamaria Navarro, Àngel|||0000-0002-6328-1423
Finalista del Georges Giralt PhD Award 2018, a la millor tesi europea sobre robòtica, The ability to fly has greatly expanded the possibilities for robots to perform surveillance, inspection or map generation tasks. Yet it was only in recent years that research in aerial robotics was mature enough to allow active interactions with the environment. The robots responsible for these interactions are called aerial manipulators and usually combine a multirotor platform and one or more robotic arms. The main objective of this thesis is to formalize the concept of aerial manipulator and present guidance methods, using visual information, to provide them with autonomous functionalities. A key competence to control an aerial manipulator is the ability to localize it in the environment. Traditionally, this localization has required external infrastructure of sensors (e.g., GPS or IR cameras), restricting the real applications. Furthermore, localization methods with on-board sensors, exported from other robotics fields such as simultaneous localization and mapping (SLAM), require large computational units becoming a handicap in vehicles where size, load, and power consumption are important restrictions. In this regard, this thesis proposes a method to estimate the state of the vehicle (i.e., position, orientation, velocity and acceleration) by means of on-board, low-cost, light-weight and high-rate sensors. With the physical complexity of these robots, it is required to use advanced control techniques during navigation. Thanks to their redundancy on degrees-of-freedom, they offer the possibility to accomplish not only with mobility requirements but with other tasks simultaneously and hierarchically, prioritizing them depending on their impact to the overall mission success. In this work we present such control laws and define a number of these tasks to drive the vehicle using visual information, guarantee the robot integrity during flight, and improve the platform stability or increase arm operability. The main contributions of this research work are threefold: (1) Present a localization technique to allow autonomous navigation, this method is specifically designed for aerial platforms with size, load and computational burden restrictions. (2) Obtain control commands to drive the vehicle using visual information (visual servo). (3) Integrate the visual servo commands into a hierarchical control law by exploiting the redundancy of the robot to accomplish secondary tasks during flight. These tasks are specific for aerial manipulators and they are also provided. All the techniques presented in this document have been validated throughout extensive experimentation with real robotic platforms., La capacitat de volar ha incrementat molt les possibilitats dels robots per a realitzar tasques de vigilància, inspecció o generació de mapes. Tot i això, no és fins fa pocs anys que la recerca en robòtica aèria ha estat prou madura com per començar a permetre interaccions amb l’entorn d’una manera activa. Els robots per a fer-ho s’anomenen manipuladors aeris i habitualment combinen una plataforma multirotor i un braç robòtic. L’objectiu d’aquesta tesi és formalitzar el concepte de manipulador aeri i presentar mètodes de guiatge, utilitzant informació visual, per dotar d’autonomia aquest tipus de vehicles. Una competència clau per controlar un manipulador aeri és la capacitat de localitzar-se en l’entorn. Tradicionalment aquesta localització ha requerit d’infraestructura sensorial externa (GPS, càmeres IR, etc.), limitant així les aplicacions reals. Pel contrari, sistemes de localització exportats d’altres camps de la robòtica basats en sensors a bord, com per exemple mètodes de localització i mapejat simultànis (SLAM), requereixen de gran capacitat de còmput, característica que penalitza molt en vehicles on la mida, pes i consum elèctric son grans restriccions. En aquest sentit, aquesta tesi proposa un mètode d’estimació d’estat del robot (posició, velocitat, orientació i acceleració) a partir de sensors instal·lats a bord, de baix cost, baix consum computacional i que proporcionen mesures a alta freqüència. Degut a la complexitat física d’aquests robots, és necessari l’ús de tècniques de control avançades. Gràcies a la seva redundància de graus de llibertat, aquests robots ens ofereixen la possibilitat de complir amb els requeriments de mobilitat i, simultàniament, realitzar tasques de manera jeràrquica, ordenant-les segons l’impacte en l’acompliment de la missió. En aquest treball es presenten aquestes lleis de control, juntament amb la descripció de tasques per tal de guiar visualment el vehicle, garantir la integritat del robot durant el vol, millorar de l’estabilitat del vehicle o augmentar la manipulabilitat del braç. Aquesta tesi es centra en tres aspectes fonamentals: (1) Presentar una tècnica de localització per dotar d’autonomia el robot. Aquest mètode està especialment dissenyat per a plataformes amb restriccions de capacitat computacional, mida i pes. (2) Obtenir les comandes de control necessàries per guiar el vehicle a partir d’informació visual. (3) Integrar aquestes accions dins una estructura de control jeràrquica utilitzant la redundància del robot per complir altres tasques durant el vol. Aquestes tasques son específiques per a manipuladors aeris i també es defineixen en aquest document. Totes les tècniques presentades en aquesta tesi han estat avaluades de manera experimental amb plataformes robòtiques reals, Award-winning