DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación
Tesis doctoral (DoctoralThesis)
Development of high-performance and stable electrocatalysts for alkaline water electrolysis
PhD Thesis presented at University of Zaragoza to obtain the degree of Doctor, Doctoral Program in Chemical and Environmental Engineering.-- Cum Laude, Rapid industrialization and rising living standards around the world have led to an energy crisis and severe environmental pollution caused by the excessive use of conventional fossil fuels. Preventing further climate change and reducing carbon dioxide emissions have become the most critical challenges confronting modern society. This has sparked an intense interest in discovering and designing alternative energy sources with affordable, clean, and environmentally benign features. Hydrogen energy has been recognized as a viable alternative to fossil fuels and is pivotal in neutralizing carbon emissions. H2 can be obtained using different approaches from different sources, including water, natural gas, coal, and biomass. The leading pathway for H2 production remains via steam reforming of fossil fuels. Still, this method cannot achieve the future "carbon-neutral" energy system due to its reliance on fossil fuels and high CO2 emissions.
H2 production through water electrolysis driven by renewable energy is a clean and ultralow-carbon footprint route and has been regarded as the most promising approach for high-purity H2 production. Two important half-reactions occur in water electrolysis: the Hydrogen evolution reaction (HER) on the cathode and the oxygen evolution reaction (OER) on the anode. Nonetheless, the sluggish kinetics and unfavorable thermodynamics of these reactions lead to enormous overpotential, which is the main challenge for mass hydrogen production. As a result, efficient electrocatalysts are required to ease the reaction energy barrier and expedite the reaction. To date, the most effective electrocatalysts for water electrolysis are primarily based on noble metals. For example, Pt-based electrocatalysts for HER and Ir- and Ru-derived electrocatalysts for OER. However, their scarcity and high cost obstruct them from sustainable use in large-scale applications. To circumvent this problem, in the last few decades, considerable efforts have been devoted to designing and developing electrocatalysts derived from transition metals combined with different materials such as carbon and heteroatoms, in which these materials exhibited appealing features such as good performance and availability, which made them a viable alternative to replacing the precious metals of Pt, Ir, and Ru.
This Thesis has focused on researching electrocatalysts derived from transition metals for both HER and OER electrodes. Two spinel oxides (NiFe2O4 and CoFe2O4) were prepared through hydrothermal methods for oxygen evolution reaction. They were used as precursors for further modification, in which through in situ polymerization of dopamine on the surface of the as prepared spinel oxides followed by carbonization has enabled to obtain an optimized property. The work has emphasized optimizing the electrochemical properties of these oxides by integrating them with multiple dopamine concentrations. The as-prepared CoFe2O4 powder was combined with various dopamine content (10, 20, 30, and 40 wt. %) and subjected to polymerization for 24 h and carbonization at 800 0C for 1 h under N2 atmosphere. The effect of carbonized polydopamine on the overall physicochemical properties and electrochemical activity of CoFe2O4 electrocatalysts was systematically investigated. There was a noticeable change from a CoFe2O4 structure to a CoFe alloy when the ratio of CoFe2O4 to dopamine was optimized. The same procedure was employed to modify the NiFe2O4. The morphology, crystalline structure, and chemical composition of the catalysts were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and inductively coupled plasma (ICP). The as-prepared electrocatalysts were measured for their electrochemical performance in a three-electrode system controlled by a potentiostat/galvanostat. In particular, CoFe/NC30% (prepared with 30wt.% dopamine) electrocatalyst exhibits excellent catalytic activity towards OER, in which a small overpotential of 340 mV was required to generate a current density of 10 mA cm−2 in a 1.0 M KOH accompanied with outstanding durability. In the case of NiFe2O4, NiFe/NC10% electrocatalyst that contains 10 wt. % dopamine showed a relatively higher catalytic activity for OER measured in 1 M KOH aqueous solution. It revealed a low overpotential (350 mV at 10 mAcm-2), a low Tafel slope (56 mVdec-1), a low charge transfer resistance, and a relatively higher electrochemically active surface area.
Moreover, a carbonaceous substance other than polydopamine was utilized to improve the electrochemical properties of CoFe. Carbon foam derived from petroleum pitch was synthesized and used to immobilize the Co and Fe electroactive metals. The bare carbon foam and heteroatom (P, N) co-doped carbon foam were produced through a simple thermal-chemical and carbonization process. The resulting composite materials were evaluated for their physical and chemical properties as well as electrochemical properties. The prepared electrocatalysts showed excellent electrocatalytic activity, faster reaction kinetics, and stability for OER electrodes, thanks to the carbon foam support that allowed for the immobilization of the Co and Fe electroactive metals. To generate a current density of 10 mA cm-2, the synthesized CoFe@PN-CF electrocatalyst requires a low overpotential of 320 mV, a low Tafel slope of 48 mV dec-1, a relatively low charge transfer resistance, and a large electrochemically active surface area. Notably, it maintained stability for at least 20 hours, suggesting it could be used for large-scale water electrolysis.
In addition to the OER electrode, efforts have been devoted to designing and developing an electrocatalyst for the HER electrode. In this case, a stainless steel mesh (SSM) with a three-dimensional network structure was used as a substrate for growing transition metals. The commercial SSM material was transformed into an active and stable electrocatalyst through a hydrothermal and phosphorization process. Single and bimetals of Ni and Co were grown on the SSM substrate using the hydrothermal method, and the resulting material was subjected to further phosphorization. Electrochemical analysis showed that the NiCoP@SSM catalyst has excellent catalytic activity for HER in 1 M KOH, with a current density of 10 mA cm-2 achieved at a low overpotential of 138 mV. This synthesis method provides a simple, binder-free, and scalable fabrication process.
Finally, the as-prepared electrocatalysts were evaluated for their performance in a single-cell anion exchange membrane water electrolysis. The results showed promising performance, particularly for the OER electrode. All electrocatalysts demonstrated attractive electroactivity. Among them, CoFe@PN-CF was found to have the highest activity, producing a current density of 0.45 Acm-2 at a cell potential of 1.8V when using CoFe@PN-CF in the anode and Pt/C in the cathode electrode., PhD thesis under the fellowship of Marie Skłodowska–Curie Action –International Training Network (MSCA–ITN) in the project of Bimetallic catalyst knowledge-based development for energy applications (BIKE, Grant agreement ID: 813748., Peer reviewed
Proyecto:
EC / H2020 813748