Pasar al contenido principal

DISPOSITIVOS OPTOMECANICOS BASADOS EN MATERIALES ACTIVOS Y AUTOENSAMBLADOS

RTI2018-093921-A-C44

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario FUNDACIÓ INSTITUT CATALÀ DE NANOCIÈNCIA I NANOTECNOLOGIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A Self-Assembled 2D Thermofunctional Material for Radiative Cooling

  • Jaramillo-Fernandez, Juliana
  • Whitworth, Guy L.
  • Pariente González, J. Ángel
  • Blanco Montes, Álvaro
  • García Fernández, Pedro David
  • López, Cefe
  • Sotomayor Torres, C. M.
[EN] The regulation of temperature is a major energy-consuming process of humankind. Today, around 15% of the global-energy consumption is dedicated to refrigeration and this figure is predicted to triple by 2050, thus linking global warming and cooling needs in a worrying negative feedback-loop. Here, an inexpensive solution is proposed to this challenge based on a single layer of silica microspheres self-assembled on a soda-lime glass. This 2D crystal acts as a visibly translucent thermal-blackbody for above-ambient radiative cooling and can be used to improve the thermal performance of devices that undergo critical heating during operation. The temperature of a silicon wafer is found to be 14 K lower during daytime when covered with the thermal emitter, reaching an average temperature difference of 19 K when the structure is backed with a silver layer. In comparison, the soda-lime glass reference used in the measurements lowers the temperature of the silicon by just 5 K. The cooling power of this simple radiative cooler under direct sunlight is found to be 350 W m when applied to hot surfaces with relative temperatures of 50 K above the ambient. This is crucial to radiatively cool down devices, i.e., solar cells, where an increase in temperature has drastic effects on performance., The European Union’s Horizon 2020 research and innovation program under the Marie Sklodoswa-Curie grant agreement N 665919 supported J.J.-F. and funded this project. Moreover, the research received funds from the Spanish Minister of Science, Innovation and Universities via the Severo Ochoa Program (Grant No. SEV-2017-0706), RTI2018-093921-B-C41 and RTI2018-093921-A-C44 (SMOOTH), as well as by the CERCA Program/Generalitat de Catalunya. P.D.G. was supported by a Ramon y Cajal fellowship nr. RyC-2015-18124. J.J
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Quantifying the robustness of topological slow light

  • Arregui, Guillermo
  • Gomis-Bresco, J.
  • Sotomayor Torres, C. M.
  • García Fernández, Pedro David
The backscattering mean free path ξ, the average ballistic propagation length along a waveguide, quantifies the resistance of slow light against unwanted imperfections in the critical dimensions of the nanostructure. This figure of merit determines the crossover between acceptable slow-light transmission affected by minimal scattering losses and a strong backscattering-induced destructive interference when the waveguide length L exceeds ξ. Here, we calculate the backscattering mean free path for a topological photonic waveguide for a specific and determined amount of disorder and, equally relevant, for a fixed value of the group index ng which is the slowdown factor of the group velocity with respect to the speed of light in vacuum. These two figures of merit, ξ and ng, should be taken into account when quantifying the robustness of topological and conventional (nontopological) slow-light transport at the nanoscale. Otherwise, any claim on a better performance of topological guided light over a conventional one is not justified., This work was supported by the European Commission H2020 FET Proactive project TOCHA (No. 824140). The authors acknowledge funding by the Severo Ochoa program from Spanish MINECO (Grant No. SEV-2019-0706) and the Plan Nacional RTI2018-093921-A-C44 (SMOOTH) and CERCA Programme/Generalitat de Catalunya. G. A. was supported by a H2020 MSC cofund action, a BIST Ph.D. fellowship, and P. D. G. by a Ramon y Cajal Fellowship No. RyC-2015-18124., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Highly-Scattering Cellulose-Based Films for Radiative Cooling

  • Jaramillo-Fernandez, Juliana
  • Yang, Han
  • Schertel, Lukas
  • Whitworth, Guy L.
  • García Fernández, Pedro David
  • Vignolini, Silvia
  • Sotomayor Torres, C. M.
Passive radiative cooling (RC) enables the cooling of objects below ambient temperature during daytime without consuming energy, promising to be a game changer in terms of energy savings and CO reduction. However, so far most RC surfaces are obtained by energy-intensive nanofabrication processes or make use of unsustainable materials. These limitations are overcome by developing cellulose films with unprecedentedly low absorption of solar irradiance and strong mid-infrared (mid-IR) emittance. In particular, a cellulose-derivative (cellulose acetate) is exploited to produce porous scattering films of two different thicknesses, L ≈ 30 µm (thin) and L ≈ 300 µm (thick), making them adaptable to above and below-ambient cooling applications. The thin and thick films absorb only (Formula presented.) of the solar irradiance, which represents a net cooling power gain of at least 17 W m, compared to state-of-the-art cellulose-based radiative-cooling materials. Field tests show that the films can reach up to ≈5 °C below ambient temperature, when solar absorption and conductive/convective losses are minimized. Under dryer conditions (water column = 1 mm), it is estimated that the films can reach average minimum temperatures of ≈7–8 °C below the ambient. The work presents an alternative cellulose-based material for efficient radiative cooling that is simple to fabricate, cost-efficient and avoids the use of polluting materials., This work was supported by the BBSRC David Phillips fellowship (BB/K014617/1) and the Horizon 2020 Framework Programme Marie Curie Individual Fellowship (793643-MFCPF), ERC SeSaME ERC2014STG H2020 639088, the PoC 963872, Cellunan, and the Isaac Newton Trust (SNSF3) and the Philip Leverhulme Prize (PLP-2019-271). The European Union Horizon 2020 Research and Innovation Program partly funded this research (Marie Sklodoswa-Curie Actions Grant No. 665919 that supported J.J.F and the project FLEXPOL Grant. No. 721062 that supported G.L.W). Moreover, the research received funds from the Spanish Minister of Science, Innovation and Universities via the Severo Ochoa Program (Grant No. SEV-2017-0706) that supports ICN2, and the projects PGC2018-101743-B-I00 (SIP) and RTI2018-093921-A-C44 (SMOOTH), as well as by the CERCA Program/Generalitat de Catalunya. L.S. acknowledges the support of the Swiss National Science Foundation under project 40B1-0 198708. P.D.G gratefully acknowledges the support the Ramon y Cajal fellowship (RYC-2015-18124).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Engineering nanoscale hypersonic phonon transport

  • Florez, Omar
  • Arregui, Guillermo
  • Albrechtsen, Marcus
  • Ng, Ryan C.
  • Gomis-Bresco, J.
  • Stobbe, Søren
  • Sotomayor Torres, C. M.
  • García Fernández, Pedro David
Controlling vibrations in solids is crucial to tailor their elastic properties and interaction with light. Thermal vibrations represent a source of noise and dephasing for many physical processes at the quantum level. One strategy to avoid these vibrations is to structure a solid such that it possesses a phononic stop band, that is, a frequency range over which there are no available elastic waves. Here we demonstrate the complete absence of thermal vibrations in a nanostructured silicon membrane at room temperature over a broad spectral window, with a 5.3-GHz-wide bandgap centred at 8.4 GHz. By constructing a line-defect waveguide, we directly measure gigahertz guided modes without any external excitation using Brillouin light scattering spectroscopy. Our experimental results show that the shamrock crystal geometry can be used as an efficient platform for phonon manipulation with possible applications in optomechanics and signal processing transduction., This project has received funding from the European Union’s H2020 FET Proactive project TOCHA (No. 824140) and Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement (No. 754558). The ICN2 authors acknowledge funding from the Severo Ochoa programme from Spanish MINECO (No. SEV-2019-0706), Plan Nacional (RTI2018-093921-A-C44 - SMOOTH) and MCIN project SIP (PGC2018-101743-B-100), as well as by the CERCA Programme Generalitat de Catalunya. O.F. and G.A. are supported by BIST PhD Fellowships, R.C.N. by a Marie Sklodowska-Curie fellowship (No. 897148) and P.D.G. by a Ramon y Cajal fellowship (No. RyC-2015-18124). M.A. and S.S. gratefully acknowledge funding from the Villum Foundation Young Investigator Programme (No. 13170), the Danish National Research Foundation (No. DNRF147 – NanoPhoton), Innovation Fund Denmark (No. 0175-00022 – NEXUS) and Independent Research Fund Denmark (No. 0135-00315 – VAFL)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cavity Optomechanics with Anderson-Localized Optical Modes

  • Arregui, Guillermo
  • Ng, Ryan C.
  • Albrechtsen, Marcus
  • Stobbe, Søren
  • Sotomayor Torres, C. M.
  • García Fernández, Pedro David
Confining photons in cavities enhances the interaction between light and matter. In cavity optomechanics, this enables a wealth of phenomena ranging from optomechanically induced transparency to macroscopic objects cooled to their motional ground state. Previous work in cavity optomechanics employed devices where ubiquitous structural disorder played no role beyond perturbing resonance frequencies and quality factors. More generally, the interplay between disorder, which must be described by statistical physics, and optomechanical effects has thus far been unexplored. Here, we demonstrate how sidewall roughness in air-slot photonic-crystal waveguides can induce sufficiently strong backscattering of slot-guided light to create Anderson-localized modes with quality factors as high as half a million and mode volumes estimated to be below the diffraction limit. We observe how the interaction between these disorder-induced optical modes and in-plane mechanical modes of the slotted membrane is governed by a distribution of coupling rates, which can exceed g_{o}/2π∼200  kHz, leading to mechanical amplification up to self sustained oscillations via optomechanical backaction. Our Letter constitutes the first steps towards understanding optomechanics in the multiple-scattering regime and opens new perspectives for exploring complex systems with a multitude of mutually coupled degrees of freedom., This work was supported by the Spanish Minister of Science, Innovation and Universities via the Severo Ochoa Program (Grant No. SEV-2017-0706) as well as by the CERCA Program/Generalitat de Catalunya and the EU-H2020 FET Proactive project TOCHA (No. 824140). G. A. was supported by the project RTI2018-093921-A-C44 (SMOOTH). R. C. N. acknowledges funding from the EU-H2020 research and innovation programme under the Marie Sklodowska-Curie (Grant No. 897148). P. D. gratefully acknowledges the support of a Ramon y Cajal fellowship (RYC-2015-18124) and C. M. S. T. acknowledges the support of the national project SIP (Grant No. PGC2018-104333-BI00). M. A. and S. S. gratefully acknowledge funding from the Villum Foundation Young Investigator Program (Grant No. 13170), the Danish National Research Foundation (Grant No. DNRF147—NanoPhoton), Innovation Fund Denmark (Grant No. 0175-00022—NEXUS), and Independent Research Fund Denmark (Grant No. 0135-00315—VAFL)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced behaviour of a passive thermoelectric generator with phase change heat exchangers and radiative cooling

  • Astrain, David
  • Jaramillo-Fernandez, Juliana
  • Araiz, Miguel
  • Francone, Achille
  • Catalán, Leyre
  • Jacobo-Martín, Alejandra
  • Alegría, Patricia
  • Sotomayor Torres, C. M.
Heat exchangers are essential to optimize the efficiency of Thermoelectric Generators (TEGs), and heat pipes without fans have proven to be an advantageous design as it maintains the characteristic robustness of thermoelectricity, low maintenance and lack of moving parts. However, the efficiency of these heat exchangers decreases under natural convection conditions, reducing their heat transfer capacity and thus thermoelectric power production. This work reports on a novel heat exchanger that combines for the first time, phase change and radiative cooling in a thermoelectric generator to improve its efficiency and increase the production of electrical energy, specially under natural convection. For this, two thermoelectric generators with heat-pipes on their cold sides have been tested: one with the radiative coating and the other without it. Their thermal resistances have been determined and the electric power output was compared under different working conditions, namely, natural convection and forced convection indoors and outdoors. The experimental tests show a clear reduction of the heat exchanger thermal resistance thanks to the radiative coating and consequently, an increase of electric production 8.3 % with outdoor wind velocities of 1 m/s, and up to 54.8 % under free convection conditions. The application of the radiative surface treatment is shown to result in a more stable electrical energy production, suppressing the drastic decrease in the generated electric power that occurs in thermoelectric generators when they work under free convection., The authors acknowledge the support of the Spanish Ministry of Science, Innovation and Universities, and the European Regional Development Fund, under grants PID2021-124014OB-I00 (VIVOTEG), TED2021-129359B-I00 (GEOTEG), PGC2018-101743-B-I00 (SIP) and RTI2018-093921-A-C44 (SMOOTH). The ICN2 authors thank the CERCA Program/Generalitat de Catalunya. Open access funding provided by Universidad Pública de Navarra., Peer reviewed
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Simulations of micro-sphere/shell 2D silica photonic crystals for radiative cooling

  • Whitworth, Guy L.|||0000-0002-5060-6946
  • Jaramillo Fernández, Juliana|||0000-0002-4787-3904
  • Pariente, Jose Angel|||0000-0003-2649-9164
  • Garcia, Pedro David
  • Blanco, Alvaro|||0000-0002-0015-4873
  • Lopez, Cefe
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
Passive daytime radiative cooling has recently become an attractive approach to address the global energy demand associated with modern refrigeration technologies. One technique to increase the radiative cooling performance is to engineer the surface of a polar dielectric material to enhance its emittance atwavelengths in the atmospheric infrared transparency window (8-13 ìm) by outcoupling surface-phonon polaritons (SPhPs) into free-space. Here we present a theoretical investigation of new surface morphologies based upon self-assembled silica photonic crystals (PCs) using an in-house built rigorous coupled-wave analysis (RCWA) code. Simulations predict that silica micro-sphere PCs can reach up to 73 K below ambient temperature, when solar absorption and conductive/convective losses can be neglected. Micro-shell structures are studied to explore the direct outcoupling of the SPhP, resulting in near-unity emittance between 8 and 10 ìm. Additionally, the effect of material composition is explored by simulating soda-lime glass micro-shells, which, in turn, exhibit a temperature reduction of 61 K below ambient temperature. The RCWA code was compared to FTIR measurements of silica micro-spheres, self-assembled on microscope slides.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Highly-Scattering Cellulose-Based Films for Radiative Cooling

  • Jaramillo Fernández, Juliana|||0000-0002-4787-3904
  • Yang, Han
  • Schertel, Lukas
  • Whitworth, Guy L.|||0000-0002-5060-6946
  • Garcia, Pedro David
  • Vignolini, Silvia
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
Passive radiative cooling (RC) enables the cooling of objects below ambient temperature during daytime without consuming energy, promising to be a game changer in terms of energy savings and CO2 reduction. However, so far most RC surfaces are obtained by energy-intensive nanofabrication processes or make use of unsustainable materials. These limitations are overcome by developing cellulose films with unprecedentedly low absorption of solar irradiance and strong mid-infrared (mid-IR) emittance. In particular, a cellulose-derivative (cellulose acetate) is exploited to produce porous scattering films of two different thicknesses, L ≈ 30 µm (thin) and L ≈ 300 µm (thick), making them adaptable to above and below-ambient cooling applications. The thin and thick films absorb only ≈5% of the solar irradiance, which represents a net cooling power gain of at least 17 W m-2, compared to state-of-the-art cellulose-based radiative-cooling materials. Field tests show that the films can reach up to ≈5 °C below ambient temperature, when solar absorption and conductive/convective losses are minimized. Under dryer conditions (water column = 1 mm), it is estimated that the films can reach average minimum temperatures of ≈7-8 °C below the ambient. The work presents an alternative cellulose-based material for efficient radiative cooling that is simple to fabricate, cost-efficient and avoids the use of polluting materials.
Dipòsit Digital de Documents de la UAB
Publicación Artículo preliminar (WorkingPaper)

Engineering nanoscale hypersonic phonon transport

  • Florez, Omar|||0000-0001-6662-9811
  • Arregui Bravo, Guillermo|||0000-0002-6458-5277
  • Albrechtsen, Marcus|||0000-0003-4226-0997
  • Ng, Ryan C.|||0000-0002-0527-9130
  • Gomis-Bresco, Jordi|||0000-0002-6066-7064
  • Stobbe, Søren|||0000-0002-0991-041X
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • García Fernández, Pedro David|||0000-0002-3422-178X
Controlling the vibrations in solids is crucial to tailor their mechanical properties and their interaction with light. Thermal vibrations represent a source of noise and dephasing for many physical processes at the quantum level. One strategy to avoid these vibrations is to structure a solid such that it possesses a phononic stop band, i.e., a frequency range over which there are no available mechanical modes. Here, we demonstrate the complete absence of mechanical vibrations at room temperature over a broad spectral window, with a 5.3 GHz wide band gap centered at 8.4 GHz in a patterned silicon nanostructure membrane measured using Brillouin light scattering spectroscopy. By constructing a line-defect waveguide, we directly measure GHz localized modes at room temperature. Our experimental results of thermally excited guided mechanical modes at GHz frequencies provides an eficient platform for photon-phonon integration with applications in optomechanics and signal processing transduction.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Enhanced behaviour of a passive thermoelectric generator with phase change heat exchangers and radiative cooling

  • Astrain, David|||0000-0002-6987-0640
  • Jaramillo Fernández, Juliana|||0000-0002-4787-3904
  • Araiz, Miguel|||0000-0002-7674-0078
  • Francone, Achille|||0000-0001-7757-9901
  • Catalán, Leyre|||0000-0003-0140-6689
  • Jacobo-Martín, Alejandra|||0000-0003-2404-2881
  • Alegría, Patricia
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
Heat exchangers are essential to optimize the efficiency of Thermoelectric Generators (TEGs), and heat pipes without fans have proven to be an advantageous design as it maintains the characteristic robustness of thermoelectricity, low maintenance and lack of moving parts. However, the efficiency of these heat exchangers decreases under natural convection conditions, reducing their heat transfer capacity and thus thermoelectric power production. This work reports on a novel heat exchanger that combines for the first time, phase change and radiative cooling in a thermoelectric generator to improve its efficiency and increase the production of electrical energy, specially under natural convection. For this, two thermoelectric generators with heat-pipes on their cold sides have been tested: one with the radiative coating and the other without it. Their thermal resistances have been determined and the electric power output was compared under different working conditions, namely, natural convection and forced convection indoors and outdoors. The experimental tests show a clear reduction of the heat exchanger thermal resistance thanks to the radiative coating and consequently, an increase of electric production 8.3 % with outdoor wind velocities of 1 m/s, and up to 54.8 % under free convection conditions. The application of the radiative surface treatment is shown to result in a more stable electrical energy production, suppressing the drastic decrease in the generated electric power that occurs in thermoelectric generators when they work under free convection.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Enhanced behaviour of a passive thermoelectric generator with phase change heat exchangers and radiative cooling

  • Astrain Ulibarrena, David
  • Jaramillo-Fernández, Juliana
  • Araiz Vega, Miguel
  • Francone, Achille
  • Catalán Ros, Leyre
  • Jacobo-Martín, Alejandra
  • Alegría Cía, Patricia
  • Sotomayor-Torres, Clivia M.
Heat exchangers are essential to optimize the efficiency of Thermoelectric Generators (TEGs), and heat pipes without fans have proven to be an advantageous design as it maintains the characteristic robustness of thermoelectricity, low maintenance and lack of moving parts. However, the efficiency of these heat exchangers decreases under natural convection conditions, reducing their heat transfer capacity and thus thermoelectric power production. This work reports on a novel heat exchanger that combines for the first time, phase change and radiative cooling in a thermoelectric generator to improve its efficiency and increase the production of electrical energy, specially under natural convection. For this, two thermoelectric generators with heat-pipes on their cold sides have been tested: one with the radiative coating and the other without it. Their thermal resistances have been determined and the electric power output was compared under different working conditions, namely, natural convection and forced convection indoors and outdoors. The experimental tests show a clear reduction of the heat exchanger thermal resistance thanks to the radiative coating and consequently, an increase of electric production 8.3 % with outdoor wind velocities of 1 m/s, and up to 54.8 % under free convection conditions. The application of the radiative surface treatment is shown to result in a more stable electrical energy production, suppressing the drastic decrease in the generated electric power that occurs in thermoelectric generators when they work under free convection., The authors acknowledge the support of the Spanish Ministry of Science, Innovation and Universities, and the European Regional Development Fund , under grants PID2021-124014OB-I00 (VIVOTEG), TED2021-129359B-I00 (GEOTEG), PGC2018-101743-B-I00 (SIP) and RTI2018-093921-A-C44 (SMOOTH). Open access funding provided by Universidad Pública de Navarra.