Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Behavioural Study of the Force Control Loop Used in a Collaborative Robot for Sanding Materials

  • Pérez Ubeda, Rodrigo
  • Gutiérrez, S. C.|||0000-0002-9106-9120
  • Zotovic Stanisic, Ranko|||0000-0002-4746-2101
  • Perles, Angel|||0000-0002-5782-4284
[EN] The rise of collaborative robots urges the consideration of them for different industrial tasks such as sanding. In this context, the purpose of this article is to demonstrate the feasibility of using collaborative robots in processing operations, such as orbital sanding. For the demonstration, the tools and working conditions have been adjusted to the capacity of the robot. Materials with different characteristics have been selected, such as aluminium, steel, brass, wood, and plastic. An inner/outer control loop strategy has been used, complementing the robot¿s motion control with an outer force control loop. After carrying out an explanatory design of experiments, it was observed that it is possible to perform the operation in all materials, without destabilising the control, with a mean force error of 0.32%. Compared with industrial robots, collaborative ones can perform the same sanding task with similar results. An important outcome is that unlike what might be thought, an increase in the applied force does not guarantee a better finish. In fact, an increase in the feed rate does not produce significant variation in the finish¿less than 0.02 m; therefore, the process is in a ¿saturation state¿ and it is possible to increase the feed rate to increase productivity., Rodrigo Perez-Ubeda is grateful to the Ph.D. Grant CONICYT PFCHA/Doctorado Becas Chile/2017-72180157 and the University of Antofagasta, Chile.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Force Control Improvement in Collaborative Robots through Theory Analysis and Experimental Endorsement

  • Pérez-Ubeda, Rodrigo
  • Zotovic Stanisic, Ranko|||0000-0002-4746-2101
  • Gutiérrez, S. C.|||0000-0002-9106-9120
[EN] Due to the elasticity of their joints, collaborative robots are seldom used in applications with force control. Besides, the industrial robot controllers are closed and do not allow the user to access the motor torques and other parameters, hindering the possibility of carrying out a customized control. A good alternative to achieve a custom force control is sending the output of the force regulator to the robot controller through motion commands (inner/outer loop control). There are different types of motion commands (e.g., position or velocity). They may be implemented in different ways (Jacobian inverse vs. Jacobian transpose), but this information is usually not available for the user. This article is dedicated to the analysis of the effect of different inner loops and their combination with several external controllers. Two of the most determinant factors found are the type of the inner loop and the stiffness matrix. The theoretical deductions have been experimentally verified on a collaborative robot UR3, allowing us to choose the best behaviour in a polishing operation according to pre-established criteria., The authors are grateful for the financial support of the Spanish Ministry of Economy and European Union, grant DPI2016-81002-R (AEI/FEDER, UE), to the research work here published. Rodrigo Perez-Ubeda is grateful to the Ph.D. Grant CONICYT PFCHA/DOCTORADO BECAS CHILE/2017-72180157.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of the application of a collaborative robot for machining tasks

  • Pérez-Ubeda, R.
  • Gutiérrez, S. C.|||0000-0002-9106-9120
  • Zotovic Stanisic, Ranko|||0000-0002-4746-2101
  • Lluch-Cerezo, Joaquín|||0000-0003-1973-0188
[EN] The importance of collaborative robots is increasing very fast in the industry. They have several advantages over the 'classical' robot arms: they may work side-by-side with humans, their environment needs less adaptation, they may be easily transported, etc. Their joints are more elastic than those in classical robots. For this reason, they are less suited for machining. In this work, a collaborative robot, a sensor of 6 Degree of Freedom (DOF) and a spindle with flex-shaft attachment are used to perform milling operations on soft materials. An inner/outer loop control is being developed to control the movements and the cutting forces. The experiments have been designed to evaluate the capability of the robot with milling operations with different parameters. An analysis of the dimensions and the finished surface will be carried out. The contribution of this article is to determine the possibilities and limitations of the collaborative robots in machining applications, with external control of forces., The authors are grateful for the financial support of the Spanish Ministry of Economy and European Union, grant DPI2016-81002-R (AEI/FEDER, UE). This work was funded by the CONICYT PFCHA/DOCTORADO BECAS CHILE/2017 - 72180157