Skip to main content

SISTEMA DE APOYO A LA TOMA DE DECISIONES DURANTE EL CICLO DE VIDA DE LAS INFRAESTRUCTURAS: SMART-INFRASTRUCTURES

BIA2013-47290-R

•
Funding agency name Ministerio de Economía y Competitividad
Funding agency acronym MINECO
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2013
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Management unit Secretaría de Estado de Educación, Formación Profesional y Universidades
Beneficiary centre UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 31
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Calibration of the descent local search algorithm parameters using orthogonal arrays

  • Gisbert Doménech, Carlos Miguel
  • Paya-Zaforteza, Ignacio
  • Lozano-Galant, Jose A.
  • Turmo, Jose
[EN] Solving optimization problems using heuristic algorithms requires the selection of its parameters. Traditionally, these parameters are selected by a trial and error process that cannot guarantee the quality of the results obtained because not all the potential combinations of parameters are checked. To fill this gap, this paper proposes the application of Taguchi's orthogonal arrays to calibrate the parameters of a heuristic optimization algorithm (the descent local search algorithm). This process is based on the study of the combinations of discrete values of the heuristic tool parameters and it enables optimization of the heuristic tool performance with a reduced computational effort. To check its efficiency, this methodology is applied to a technical challenge never studied before: the optimization of the tensioning process of cable-stayed bridges. The statistical improvement of the heuristic tool performance is studied by the optimization of the tensioning process of a real cable-stayed bridge. Results show that the proposed calibration technique provided robust values of the objective function (with lower minimum and mean values, and lower standard deviation) with reduced computational cost., The authors are indebted to the Spanish Ministry of Economy and Competitiveness for the funding provided through the research projects BIA2013-47290-R and BIA2017-86811-C2-1-R founded with FEDER funds and directed by Professor Jose Turmo and through the research project BIA2017-86811-C2-2-R directed by Jose Antonio Lozano-Galant.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Modifications of the stress-state of cable-stayed bridges due to staggered construction of their superstructure

  • Lozano-Galant, Jose Antonio
  • Ruiz Ripoll, Lidia
  • Paya-Zaforteza I.
  • Turmo, José
In current practice, the effects of the evolutionary erection of cable-stayed bridge superstructure are rarely included into the simulation of its tensioning process. In fact, stay forces in service are usually defined in early stages of design, when the construction process has not even been conceived in detail yet. In order to fill this gap, the effects of the evolutionary erection of cable-stayed bridge superstructure throughout the tensioning process are studied in this paper. This study is focused on steel cable-stayed bridges erected on temporary supports. For the very first time a new criterion to include the effects of the evolutionary erection of cable-stayed bridges into the definition of the stay forces in the service state is presented., The authors wish to thank the Ministerio de Economia y Competitividad, the Ministerio de Ciencia e Innovacion and the Junta de Comunidades de Castilla-La Mancha (Spain) for the funding provided through the research projects BIA2013-47290-R, BIA2009-13056 and PII2I09-0129-4085 directed by Jose Turmo and founded with FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effects in service of the staggered construction of cable-stayed bridges built on temporary supports

  • Lozano Galant, José Antonio
  • Turmo Coderque, José
  • Paya-Zaforteza, Ignacio
Cable-stayed bridges can be rarely built on a single construction stage and staggered construction is commonly used. The effects of this staggered construction are not only economical as they might also play an important role in the structural behaviour in service. Despite of this importance, these effects are rarely included into the definition of the structural response in service. In order to fill this gap, this paper deals with the effects in service of the staggered erection of steel cable-stayed bridges built on temporary supports. To do so, a criterion based on the minimization of the bending energy in terms of stay forces is applied to several cable-stayed bridges. This study shows the importance of the existence of the pylon-deck connection as well as the number and location of both construction joints and temporary supports during staggered erection, The authors thank the Spanish Ministerio de Economia y Competitividad and the FEDER funds for the funding provided through the research grant BIA2013-47290-R directed by Jose Turmo.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of Eduardo Torroja&apos, s Tempul Aqueduct an important precursor of modern cable-stayed bridges, extradosed bridges and prestressed concrete

  • Lozano-Galant, José Antonio
  • Paya-Zaforteza, Ignacio
[EN] This paper describes a study of the Tempul Aqueduct, one of the first structures designed and built by Eduardo Torroja. At a time when computers did not exist, Torroja's courage and innovation were outstanding. He was in no way constrained by a lack of theoretical knowledge, inadequate materials and the contemporary doubts about cable-stayed structures. In fact, he was able to build one of the world's first prestressed concrete structures, and a precursor to modern cable-stayed and extradosed bridges. This paper briefly reviews the history of the Tempul Aqueduct, gives the results of the analysis of this structure by several Finite Element Models (FEMs), and compares the FEM results to those obtained by Torroja himself. The FEM results confirm the validity of Torroja's conceptual design. The paper also contains a detailed analysis of the influence of the structural system on the behavior of the bridge and the effect of removing the live loads with the aim of providing a better understanding of the context and behavior of the Tempul aqueduct., Funding for this research has been provided to Mr Lozano-Galant by the Spanish Ministry of Economy, Industry and Competitiveness (Research Project BIA2013-47290-R from FEDER funds). The authors are also grateful to Prof. S. Buonopane of Bucknell University and J.L. Temprado, of COMPOSAN, for their assistance and support. The authors also want to thank the CEHOPU-Archivo Torroja, for all the information and support provided.
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Planning low-error SHM strategy by constrained observability method

  • Peng, Tian
  • Nogal, María
  • Casas Rius, Joan Ramon|||0000-0003-4473-4308
  • Turmo Coderque, José|||0000-0001-5001-2438
Structural identification using dynamical parameters (such as the natural vibration frequencies and mode shapes) is an important issue, especially in bridges or high-rise buildings. However, incorrect decisions could happen on the Structural Health Monitoring (SHM) strategy and the Structural System Identification (SSI) analysis that makes the sometimes expensive and time-consuming process useless due to the large uncertainty of the resulting estimations. This paper discusses the role of the SHM strategy and the SSI analysis based on the constrained observability method (COM) and decision trees (DT) in reducing the estimation error. Here, the COM uses subsets of natural frequencies and/or modal-shapes to deal with the nonlinearity of the SSI derived from the operational aspects of the methods, and combines the unknown items including frequencies and mode shapes into an optimization process. Next, a decision-support tool based on decision trees is applied to help engineers to establish the best SHM + SSI strategy yielding the most accurate estimations. The principle and steps of this new method, the combination of constrained observability m,ethod and decision trees, are presented for the first time. After that, a numerical model of a bridge case is used to show how to choose the optimal strategy, when factors such as the structure layout, span length, measurement set, and parameters of the COM are included as decision variables. The importance ranking of these four factors is the layout, measurement set, parameters of the COM, and length through the sensitivity analysis of the COM estimated. Last, a real bridge is used to validate this methodology under the undamaged and damaged scenarios by comparing an Error Index, which shows the optimal SHM + SSI strategy works well no matter the bridge is damaged or not. The presented analysis leads to significant insights that can help the decision-making of the optimal SHM + SSI strategy, avoiding erroneous decisions if this tool is not used beforehand., This work was mainly funded by the Chinese Scholarship Council through its program (No. 201808390083), which has been provided to Mrs. Peng. It is also to be noted that this work was partially funded by the Spanish Ministry of Economy and Competitiveness for the funding provided through the research projects BIA2013-47290-R and BIA2017-86811-C2-1-R founded with FEDER funds and directed by Professor José Turmo. Authors are also indebted to the Secretaria d’ Universitats i Recerca de la Generalitat de Catalunya for the funding provided through Agaur (2017 SGR 1481)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Shear crack pattern identification in concrete elements via distributed optical fibre grid

  • Rodríguez Gutiérrez, Gerardo
  • Casas Rius, Joan Ramon|||0000-0003-4473-4308
  • Villalba Herrero, Sergi|||0000-0001-6535-6372
This is an Accepted Manuscript of an article published by Taylor & Francis Group in "Structure and infrastructure engineering: maintenance, management, life-cycle design and performance" on 2019, available online at: http://www.tandfonline.com/10.1080/15732479.2019.1640256, An experimental methodology to obtain the shear cracking pattern in concrete elements is presented. The method is based on the use of Distributed Optical Fiber Sensors (DOFS) connected to an Optical Backscattered Reflectometer (OBR). Using this OBR system and a 2D grid conformed by one or two DOFS, the crack patterns of three partially pre-stressed concrete (PPC) beams subjected experimentally to shear failure, were obtained for increasing level of load. The 2D distributed fiber optic sensoring mesh was formed by attaching the fiber to the shear span of each beam using an epoxy adhesive. The importance of a correct DOFS attaching procedure to the concrete surface to obtain accurate results is described, and the principal advantages of DOFS to complement the use of discrete sensors in concrete experimental shear tests are shown. The proposed technique is a powerful tool to be implemented in the structural health monitoring in shear of concrete structures, where the variable inclined cracks are difficult to monitor by other experimental techniques using discrete sensors., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Application of low-cost sensors for accurate ambient temperature monitoring

  • Mobaraki, Behnam|||0000-0002-2924-643X
  • Komarizadehasl, Seyedmilad|||0000-0002-9010-2611
  • Castilla Pascual, Francisco Javier
  • Lozano Galant, José Antonio
In structures with reduced monitoring budgets, the high cost of commercial metering devices is always an obstacle for monitoring structural health. This might be an issue when temperatures must be measured for both structural and environmental reasons. To fill this gap, in this paper, a novel monitoring system is proposed for the accurate measurement of indoor temperature in buildings. This protocol is characterized by its generality, as it can be easily adapted to measure any structural or environmental parameters on site. The proposed monitoring system uses from one to eight low-cost sensors to obtain multiple measurements of the ambient temperatures. The accuracy ranges of the developed monitoring systems with different numbers of sensors are statistically analysed. The results indicate that the discrepancy of the measurements decreases with the increase in the number of sensors, as the maximum standard deviation of 10 sensors (0.42) decreases to 0.32 and 0.27 for clusters of 20 and 30 sensors, respectively., This research was funded by the Spanish Ministry of Economy and Competitiveness (grant number BIA2013-47290-R, BIA2017-86811-C2-1-R, and BIA2017-86811-C2-2-R) and by the Universidad de Castilla La Mancha (grant number 2018-COB-9092)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Calibration of the descent local search algorithm parameters using orthogonal arrays

  • Gisbert Doménech, Carlos Miguel
  • Lozano Galant, José Antonio
  • Payá Zaforteza, Ignacio Javier
  • Turmo Coderque, José|||0000-0001-5001-2438
This is the peer reviewed version of the following article: [ Gisbert, CM, Lozano‐Galant, JA, Paya‐Zaforteza, I, Turmo, J. Calibration of the descent local search algorithm parameters using orthogonal arrays. Comput Aided Civ Inf. 2020; 35: 997– 1008. https://doi.org/10.1111/mice.12545 ], which has been published in final form at https://onlinelibrary.wiley.com/doi/abs/10.1111/mice.12545. This article may be used for non-commercial purposes in accordance with Wiley Terms and Conditions for Self-Archiving., Solving optimization problems using heuristic algorithms requires the selection of its parameters. Traditionally, these parameters are selected by a trial and error process that cannot guarantee the quality of the results obtained because not all the potential combinations of parameters are checked. To fill this gap, this paper proposes the application of Taguchi's orthogonal arrays to calibrate the parameters of a heuristic optimization algorithm (the descent local search algorithm). This process is based on the study of the combinations of discrete values of the heuristic tool parameters and it enables optimization of the heuristic tool performance with a reduced computational effort. To check its efficiency, this methodology is applied to a technical challenge never studied before: the optimization of the tensioning process of cable-stayed bridges. The statistical improvement of the heuristic tool performance is studied by the optimization of the tensioning process of a real cable-stayed bridge. Results show that the proposed calibration technique provided robust values of the objective function (with lower minimum and mean values, and lower standard deviation) with reduced computational cost, The authors are indebted to the Spanish Ministry of Economy and Competitiveness for the funding provided through the research projects BIA2013-47290-R and BIA2017-86811-C2-1-R founded with FEDER funds and directed by Professor José Turmo and through the research project BIA2017-86811-C2-2-R directed by José Antonio Lozano-Galant., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Towards the integration and automation of the design process for domestic drinking-water and sewerage systems with BIM

  • Atencio, Edison
  • Araya, Pablo
  • Oyarce, Francisco
  • Herrera, Rodrigo F.
  • Muñoz La Rivera, Felipe
  • Lozano Galant, Fidel|||0000-0001-9272-6172
The use of building information modelling (BIM) in construction projects is expanding, and its usability throughout building lifecycles, from planning and construction to operation and maintenance, is gaining increasing proof. In the design of domestic drinking-water and sewerage systems (DDWSSs), BIM focuses on coordinating disciplines and their design. Despite studies promoting BIM environments for DDWSSs that take into account the regulatory frameworks of corresponding countries, these efforts do not include the use of parametric tools that enhance the efficiency of the design process. Therefore, engineers still use conventional 2D design, which requires many rounds of iteration, and manual work is also generally still used. In this research, we developed and validated an intuitive methodology for solving a specific DDWSS problem, using a design science research method (DSRM) as an applied science approach. This was addressed by developing an artefact and validating it through two case studies. The obtained solution combines BIM models and parametric tools to automate the manual activities of the traditional design method. This article aims to bring abstract BIM concepts into practice and encourage researchers and engineers to adopt BIM for DDWSSs., This research was funded by Proyecto VRIEA-PUCV, grant number 039.427/2021, and the Grants for the Promotion of Research in the Department of Civil and Building Engineering, UCLM. This research was also funded by Spanish Ministry of Economy and Competitiveness provided through the research project BIA2013-47290-R, BIA2017-86811-C2-1-R and BIA2017-86811-C2-2-R. All these projects were funded with FEDER funds., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Constrained observability techniques for structural system identification using modal analysis

  • Peng, Tian
  • Nogal, María
  • Casas Rius, Joan Ramon|||0000-0003-4473-4308
  • Lozano Galant, José Antonio
  • Turmo Coderque, José|||0000-0001-5001-2438
The characteristics of civil structures inevitably suffer a certain level of damage during its lifetime and cheap, non-destructive and reliable methods to assess their correct performance are of high importance. Structural System Identification (SSI) using measured response is the way to fine why performance is not correct and identify where the problems can be found. Different methods of SSI exist, both using static and vibration experimental data. However, using these methods is not always possible to decide if available measurements are sufficient to uniquely obtain the unknown. A (SSI) method that uses constrained observability method (COM) has already been developed based on the information provided by the monitoring of static non-destructive tests - using deflections and rotations under a known loading case. The method assures that all observable variables can be obtained with the available measured data. In the present paper, the problem of determining the actual characteristics of the members of a structure such as axial stiffness, flexural stiffness and mass using vibration data is analyzed. Subsets of natural frequencies and/or modal shapes are used. To give a better understanding of the proposed method and to demonstrate its potential applicability, several examples of growing complexity are analyzed, and the results show how constrained observability techniques might be efficiently used for the dynamic identification of structural systems using dynamic data. These lead to significant conclusions regarding the functioning of an SSI method based on dynamic behavior., The authors are indebted to the Spanish Ministry of Economy and Competitiveness for the funding provided through the research projects BIA2013-47290-R and BIA2017-86811-C2-1-R founded with FEDER funds and directed by Professor Jose Turmo and through the research project BIA2017-86811-C2-2-R. It is also to be noted that the part of this work was done included an exchange of faculty financed by the Chinese government to Mrs.Peng thorough the program (No. 201808390083). The financial support from the the Chinese Scholarship Council and the Spanish Ministry of Economy and Competitiveness (BES-2018-B00230) are greatly appreciated., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Structural system identification including shear deformation of composite bridges from vertical deflections

  • Emadi, Seyyedbehrad
  • Lozano Galant, José Antonio
  • Xia, Ye
  • Ramos Schneider, Gonzalo|||0000-0002-7263-8471
  • Turmo Coderque, José|||0000-0001-5001-2438
Shear deformation effects are neglected in most structural system identification methods. This assumption might lead to important errors in some structures like built up steel or composite deep beams. Recently, the observability techniques were presented as one of the first methods for the inverse analysis of structures including the shear effects. In this way, the mechanical properties of the structures could be obtained from the nodal movements measured on static tests. One of the main controversial features of this procedure is the fact that the measurement set must include rotations. This characteristic might be especially problematic in those structures where rotations cannot be measured. To solve this problem and to increase its applicability, this paper proposes an update of the observability method to enable the structural identification including shear effects by measuring only vertical deflections. This modification is based on the introduction of a numerical optimization method. With this aim, the inverse analysis of several examples of growing complexity are presented to illustrate the validity and potential of the updated method., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Design and construction of post-tensioned concrete box-girder viaducts for high-speed rail

  • Torralba Mendiola, Víctor
  • Polo Orodea, Tomás
  • Ramos Schneider, Gonzalo|||0000-0002-7263-8471
  • Aparicio Bengoechea, Ángel Carlos|||0000-0002-3029-9491
This paper explains the design criteria used for nine box-girder continuous high-speed rail viaducts constructed in Spain. It describes the longitudinal layout and an innovative construction process using movable scaffolding. A comparison between different post-tensioning and reinforcing steel ratios is provided. Recommendations for fatigue design and concrete stress criteria in the serviceability limit state are given. In addition, the paper provides the quantities of concrete, post-tensioning and reinforcing steel used in the construction of the viaducts., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Structural system identification by measurement error-minimizing observability method

  • Lei, Jun
  • Lozano Galant, José Antonio
  • Xu, Dong
  • Turmo Coderque, José|||0000-0001-5001-2438
This is the accepted version of the following article: [Lei, J, Lozano‐Galant, JA, Xu, D, Turmo, J. Structural system identification by measurement error‐minimizing observability method. Struct Control Health Monit. 2019; 26:e2425. https://doi.org/10.1002/stc.2425], which has been published in final form at https://doi.org/10.1002/stc.2425, This paper proposes a method for the finite element model updating using static load tests under the framework of observability analysis. Previous works included measurement errors in the coefficient matrix of the observability equations. This impeded the obtainment of accurate estimations. To deal with this issue, the proposed method relocates the errors and incorporates an optimization procedure to minimize the square sum of these errors. This method is able to identify the structural parameters of complex structures where the axial and bending behaviors are coupled, such as inclined beams or frame structures. Its application is illustrated by three structures. First, the method was validated in a beam-like structure by comparing it with other methods in the literature. Then the effects of different factors were investigated in a multistory frame and a rigid frame bridge with inclined piers. These factors include the curvatures, the inclusion of rotation measurements, and the constraints on the range of unidentifiable parameters. The importance of rotation measurements is demonstrated in static structural system identification., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Structural health monitoring of 2D plane structures

  • Mobaraki, Behnam|||0000-0002-2924-643X
  • Ma, Haiying
  • Lozano Galant, José Antonio
  • Turmo Coderque, José|||0000-0001-5001-2438
This paper presents the application of the observability technique for the structural system identification of 2D models. Unlike previous applications of this method, unknown variables appear both in the numerator and the denominator of the stiffness matrix system, making the problem non-linear and impossible to solve. To fill this gap, new changes in variables are proposed to linearize the system of equations. In addition, to illustrate the application of the proposed procedure into the observability method, a detailed mathematical analysis is presented. Finally, to validate the applicability of the method, the mechanical properties of a state-of-the-art plate are numerically determined., The authors are indebted to the Spanish Ministry of Economy and Competitiveness for the funding provided through the research projects BIA2013‐47290‐R, BIA2017‐86811‐C2‐1‐R, and BIA2017‐86811‐C2‐2‐R founded with FEDER funds. Funding for this research was provided to Behnam Mobaraki by the Spanish Ministry of Economy and Competitiveness through its program for his PhD. Part of this work was done through grant number 2018‐COB‐9092 from the Universidad de Castilla La Mancha (UCLM). The authors are also indebted to the Secretaria d’ Universitats i Recerca de la Generalitat de Catalunya for the funding provided through Agaur (2017 SGR 1481)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Robust static structural system identification using rotations

  • Lei, Jun
  • Lozano Galant, José Antonio
  • Xu, Dong
  • Zhang, Feng
  • Turmo Coderque, José|||0000-0001-5001-2438
Deflections are commonly measured in the static structural system identification of structures. Comparatively less attention has been paid to the possibility of measuring rotations for structural system identification purposes, despite the many advantages of using inclinometers, such as a high resolution and being reference free. Although some work using rotations can be found in the literature, this paper, for the very first time, proposes a statistical analysis that justifies the theoretical advantage of measuring rotations. The analytical expressions for the target parameters are obtained via static structural system identification using the constrained observability method first. Combined with the inverse distribution theory, the probability density function of the estimations of the target parameters can be obtained. Comparative studies on a simply supported bridge and a frame structure demonstrate the advantage of measuring rotations regarding the unbiasedness and the extent of variation in the estimations. To achieve robust parameter estimations, four strategies to use redundant rotations are proposed and compared. Numerical verifications on a bridge structure and a high-rise building have shown promising results., This work was partially funded by the Scientific Research Fund of the Institute of Engineering Mechanics, China Earthquake Administration (grant no. 2019 EEEVL0401), National Natural Science Foundation of China (grant nos. 51878484), Spanish Ministry of Economy and Competitiveness and the FEDER fund through the projects BIA2013-47290-R and BIA2017-86811-C2-1-R directed by José Turmo and BIA2017-86811-C2-2-R, and the Natural Science Foundation of Shenzhen (grant no. JCYJ20190806143618723). The authors are also indebted to the Secretaria d’Universitats i Recerca de la Generalitat de Catalunya for the funding provided through Agaur (2017 SGR 1481). Part of this work was carried out through a collaborative agreement between Tongji University (China) and the Technical University of Catalonia, UPC. This included an exchange of faculty financed by the Chinese government. The financial support from the Chinese High-End Foreign Experts program (GDW20143100115) is greatly appreciated. Funding for this research has been provided to Jun Lei by the Chinese Scholarship Council through its program No. 201506260116 and by the Spanish Ministry of Economy and Competitiveness through its program BES-2014-07022 for his PhD stays., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Safety factor calibration for a new model of shear strength of reinforced concrete building beams and slabs

  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
  • Casas Rius, Joan Ramon|||0000-0003-4473-4308
When assessing existing structures, the availability of adequate safety factors, calibrated with the most accurate models, and for established target reliability indexes, is of critical importance in order to take the right decision regarding the maintenance/repair/strengthening interventions. In the case of shear resistance in reinforced concrete (RC) structures, when using the current design codes provisions for new constructions in assessment results that, in many cases, existing structures may be considered unsafe, implying large economic costs in strengthening or even dismantling. In this research, a proposal of safety factor relative to a recently developed model for shear strength, for elements with and without transversal reinforcement, based on a reliability-based calibration is presented. A formulation is proposed to determine the adequate strength factor for a selected target reliability index of the existing structure and desired remaining service life by means of a safety factor format, considering the load factors present in the Eurocodes. The calibration is carried out considering typical geometry and load ratios of building floors, as well as normal and high strength concrete. The derived safety factor is almost independent of the chosen remaining service life., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Shear crack width assessment in concrete structures by 2D distributed optical fiber

  • Rodríguez, Gerardo
  • Casas Rius, Joan Ramon|||0000-0003-4473-4308
  • Villalba Herrero, Sergi|||0000-0001-6535-6372
This paper outlines the second part of an experimental study to show the capabilities of distributed optical fiber sensors (DOFS) in their application to the structural health monitoring (SHM) of the shear performance of concrete structures. SHM seeks to obtain the shear crack characteristics of concrete elements: detection, localization and quantification of shear damage. The two first were discussed in the first part of the experimental study. In the present paper, the quantification is dealt with by proposing a method to obtain the mean shear crack width in concrete beams. The method is based on the experimental data obtained by a DOFS bonded to the concrete surface. First, the basis of the methodology are presented and, later on, experimentally checked by testing of three partially pre-stressed concrete (PPC) beams subjected to a shear test with increasing level of load. The DOFS were deployed in the web of the beams to conform a 2D grid mesh to measure the strain profile along two orthogonal directions. The experimental data was obtained using an OBR (Optical Backscattered Reflectometer) system with high spatial resolution and sensitivity that allow a complete mapping of the cracking pattern and to obtain the required data for the calculation of the crack width. The results show the feasibility of the proposed method in calculating the shear crack width when compared to the results from traditional instrumentation, Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Shear crack pattern identification in concrete elements via distributed optical fibre grid

  • Rodríguez Gutiérrez, Gerardo
  • Casas Rius, Joan Ramon
  • Villalba Herrero, Sergi
This is an Accepted Manuscript of an article published by Taylor & Francis Group in "Structure and infrastructure engineering: maintenance, management, life-cycle design and performance" on 2019, available online at: http://www.tandfonline.com/10.1080/15732479.2019.1640256, An experimental methodology to obtain the shear cracking pattern in concrete elements is presented. The method is based on the use of Distributed Optical Fiber Sensors (DOFS) connected to an Optical Backscattered Reflectometer (OBR). Using this OBR system and a 2D grid conformed by one or two DOFS, the crack patterns of three partially pre-stressed concrete (PPC) beams subjected experimentally to shear failure, were obtained for increasing level of load. The 2D distributed fiber optic sensoring mesh was formed by attaching the fiber to the shear span of each beam using an epoxy adhesive. The importance of a correct DOFS attaching procedure to the concrete surface to obtain accurate results is described, and the principal advantages of DOFS to complement the use of discrete sensors in concrete experimental shear tests are shown. The proposed technique is a powerful tool to be implemented in the structural health monitoring in shear of concrete structures, where the variable inclined cracks are difficult to monitor by other experimental techniques using discrete sensors., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Design and construction of post-tensioned concrete box-girder viaducts for high-speed rail

  • Torralba Mendiola, Víctor
  • Polo Orodea, Tomás
  • Ramos Schneider, Gonzalo
  • Aparicio Bengoechea, Ángel Carlos
This paper explains the design criteria used for nine box-girder continuous high-speed rail viaducts constructed in Spain. It describes the longitudinal layout and an innovative construction process using movable scaffolding. A comparison between different post-tensioning and reinforcing steel ratios is provided. Recommendations for fatigue design and concrete stress criteria in the serviceability limit state are given. In addition, the paper provides the quantities of concrete, post-tensioning and reinforcing steel used in the construction of the viaducts., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Robust static structural system identification using rotations

  • Lei, Jun
  • Lozano Galant, José Antonio
  • Xu, Dong
  • Zhang, Feng
  • Turmo Coderque, José
Deflections are commonly measured in the static structural system identification of structures. Comparatively less attention has been paid to the possibility of measuring rotations for structural system identification purposes, despite the many advantages of using inclinometers, such as a high resolution and being reference free. Although some work using rotations can be found in the literature, this paper, for the very first time, proposes a statistical analysis that justifies the theoretical advantage of measuring rotations. The analytical expressions for the target parameters are obtained via static structural system identification using the constrained observability method first. Combined with the inverse distribution theory, the probability density function of the estimations of the target parameters can be obtained. Comparative studies on a simply supported bridge and a frame structure demonstrate the advantage of measuring rotations regarding the unbiasedness and the extent of variation in the estimations. To achieve robust parameter estimations, four strategies to use redundant rotations are proposed and compared. Numerical verifications on a bridge structure and a high-rise building have shown promising results., This work was partially funded by the Scientific Research Fund of the Institute of Engineering Mechanics, China Earthquake Administration (grant no. 2019 EEEVL0401), National Natural Science Foundation of China (grant nos. 51878484), Spanish Ministry of Economy and Competitiveness and the FEDER fund through the projects BIA2013-47290-R and BIA2017-86811-C2-1-R directed by José Turmo and BIA2017-86811-C2-2-R, and the Natural Science Foundation of Shenzhen (grant no. JCYJ20190806143618723). The authors are also indebted to the Secretaria d’Universitats i Recerca de la Generalitat de Catalunya for the funding provided through Agaur (2017 SGR 1481). Part of this work was carried out through a collaborative agreement between Tongji University (China) and the Technical University of Catalonia, UPC. This included an exchange of faculty financed by the Chinese government. The financial support from the Chinese High-End Foreign Experts program (GDW20143100115) is greatly appreciated. Funding for this research has been provided to Jun Lei by the Chinese Scholarship Council through its program No. 201506260116 and by the Spanish Ministry of Economy and Competitiveness through its program BES-2014-07022 for his PhD stays., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Calibration of the descent local search algorithm parameters using orthogonal arrays

  • Gisbert Doménech, Carlos Miguel
  • Lozano Galant, José Antonio
  • Payá Zaforteza, Ignacio Javier
  • Turmo Coderque, José
This is the peer reviewed version of the following article: [ Gisbert, CM, Lozano‐Galant, JA, Paya‐Zaforteza, I, Turmo, J. Calibration of the descent local search algorithm parameters using orthogonal arrays. Comput Aided Civ Inf. 2020; 35: 997– 1008. https://doi.org/10.1111/mice.12545 ], which has been published in final form at https://onlinelibrary.wiley.com/doi/abs/10.1111/mice.12545. This article may be used for non-commercial purposes in accordance with Wiley Terms and Conditions for Self-Archiving., Solving optimization problems using heuristic algorithms requires the selection of its parameters. Traditionally, these parameters are selected by a trial and error process that cannot guarantee the quality of the results obtained because not all the potential combinations of parameters are checked. To fill this gap, this paper proposes the application of Taguchi's orthogonal arrays to calibrate the parameters of a heuristic optimization algorithm (the descent local search algorithm). This process is based on the study of the combinations of discrete values of the heuristic tool parameters and it enables optimization of the heuristic tool performance with a reduced computational effort. To check its efficiency, this methodology is applied to a technical challenge never studied before: the optimization of the tensioning process of cable-stayed bridges. The statistical improvement of the heuristic tool performance is studied by the optimization of the tensioning process of a real cable-stayed bridge. Results show that the proposed calibration technique provided robust values of the objective function (with lower minimum and mean values, and lower standard deviation) with reduced computational cost, The authors are indebted to the Spanish Ministry of Economy and Competitiveness for the funding provided through the research projects BIA2013-47290-R and BIA2017-86811-C2-1-R founded with FEDER funds and directed by Professor José Turmo and through the research project BIA2017-86811-C2-2-R directed by José Antonio Lozano-Galant., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Application of low-cost sensors for accurate ambient temperature monitoring

  • Mobaraki, Behnam
  • Komarizadehasl, Seyedmilad
  • Castilla Pascual, Francisco Javier
  • Lozano Galant, José Antonio
In structures with reduced monitoring budgets, the high cost of commercial metering devices is always an obstacle for monitoring structural health. This might be an issue when temperatures must be measured for both structural and environmental reasons. To fill this gap, in this paper, a novel monitoring system is proposed for the accurate measurement of indoor temperature in buildings. This protocol is characterized by its generality, as it can be easily adapted to measure any structural or environmental parameters on site. The proposed monitoring system uses from one to eight low-cost sensors to obtain multiple measurements of the ambient temperatures. The accuracy ranges of the developed monitoring systems with different numbers of sensors are statistically analysed. The results indicate that the discrepancy of the measurements decreases with the increase in the number of sensors, as the maximum standard deviation of 10 sensors (0.42) decreases to 0.32 and 0.27 for clusters of 20 and 30 sensors, respectively., This research was funded by the Spanish Ministry of Economy and Competitiveness (grant number BIA2013-47290-R, BIA2017-86811-C2-1-R, and BIA2017-86811-C2-2-R) and by the Universidad de Castilla La Mancha (grant number 2018-COB-9092)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Towards the integration and automation of the design process for domestic drinking-water and sewerage systems with BIM

  • Atencio, Edison
  • Araya, Pablo
  • Oyarce, Francisco
  • Herrera, Rodrigo F.
  • Muñoz La Rivera, Felipe
  • Lozano Galant, Fidel
The use of building information modelling (BIM) in construction projects is expanding, and its usability throughout building lifecycles, from planning and construction to operation and maintenance, is gaining increasing proof. In the design of domestic drinking-water and sewerage systems (DDWSSs), BIM focuses on coordinating disciplines and their design. Despite studies promoting BIM environments for DDWSSs that take into account the regulatory frameworks of corresponding countries, these efforts do not include the use of parametric tools that enhance the efficiency of the design process. Therefore, engineers still use conventional 2D design, which requires many rounds of iteration, and manual work is also generally still used. In this research, we developed and validated an intuitive methodology for solving a specific DDWSS problem, using a design science research method (DSRM) as an applied science approach. This was addressed by developing an artefact and validating it through two case studies. The obtained solution combines BIM models and parametric tools to automate the manual activities of the traditional design method. This article aims to bring abstract BIM concepts into practice and encourage researchers and engineers to adopt BIM for DDWSSs., This research was funded by Proyecto VRIEA-PUCV, grant number 039.427/2021, and the Grants for the Promotion of Research in the Department of Civil and Building Engineering, UCLM. This research was also funded by Spanish Ministry of Economy and Competitiveness provided through the research project BIA2013-47290-R, BIA2017-86811-C2-1-R and BIA2017-86811-C2-2-R. All these projects were funded with FEDER funds., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Planning low-error SHM strategy by constrained observability method

  • Peng, Tian
  • Nogal, María
  • Casas Rius, Joan Ramon
  • Turmo Coderque, José
Structural identification using dynamical parameters (such as the natural vibration frequencies and mode shapes) is an important issue, especially in bridges or high-rise buildings. However, incorrect decisions could happen on the Structural Health Monitoring (SHM) strategy and the Structural System Identification (SSI) analysis that makes the sometimes expensive and time-consuming process useless due to the large uncertainty of the resulting estimations. This paper discusses the role of the SHM strategy and the SSI analysis based on the constrained observability method (COM) and decision trees (DT) in reducing the estimation error. Here, the COM uses subsets of natural frequencies and/or modal-shapes to deal with the nonlinearity of the SSI derived from the operational aspects of the methods, and combines the unknown items including frequencies and mode shapes into an optimization process. Next, a decision-support tool based on decision trees is applied to help engineers to establish the best SHM + SSI strategy yielding the most accurate estimations. The principle and steps of this new method, the combination of constrained observability m,ethod and decision trees, are presented for the first time. After that, a numerical model of a bridge case is used to show how to choose the optimal strategy, when factors such as the structure layout, span length, measurement set, and parameters of the COM are included as decision variables. The importance ranking of these four factors is the layout, measurement set, parameters of the COM, and length through the sensitivity analysis of the COM estimated. Last, a real bridge is used to validate this methodology under the undamaged and damaged scenarios by comparing an Error Index, which shows the optimal SHM + SSI strategy works well no matter the bridge is damaged or not. The presented analysis leads to significant insights that can help the decision-making of the optimal SHM + SSI strategy, avoiding erroneous decisions if this tool is not used beforehand., This work was mainly funded by the Chinese Scholarship Council through its program (No. 201808390083), which has been provided to Mrs. Peng. It is also to be noted that this work was partially funded by the Spanish Ministry of Economy and Competitiveness for the funding provided through the research projects BIA2013-47290-R and BIA2017-86811-C2-1-R founded with FEDER funds and directed by Professor José Turmo. Authors are also indebted to the Secretaria d’ Universitats i Recerca de la Generalitat de Catalunya for the funding provided through Agaur (2017 SGR 1481)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Structural system identification by measurement error-minimizing observability method

  • Lei, Jun
  • Lozano Galant, José Antonio
  • Xu, Dong
  • Turmo Coderque, José
This is the accepted version of the following article: [Lei, J, Lozano‐Galant, JA, Xu, D, Turmo, J. Structural system identification by measurement error‐minimizing observability method. Struct Control Health Monit. 2019; 26:e2425. https://doi.org/10.1002/stc.2425], which has been published in final form at https://doi.org/10.1002/stc.2425, This paper proposes a method for the finite element model updating using static load tests under the framework of observability analysis. Previous works included measurement errors in the coefficient matrix of the observability equations. This impeded the obtainment of accurate estimations. To deal with this issue, the proposed method relocates the errors and incorporates an optimization procedure to minimize the square sum of these errors. This method is able to identify the structural parameters of complex structures where the axial and bending behaviors are coupled, such as inclined beams or frame structures. Its application is illustrated by three structures. First, the method was validated in a beam-like structure by comparing it with other methods in the literature. Then the effects of different factors were investigated in a multistory frame and a rigid frame bridge with inclined piers. These factors include the curvatures, the inclusion of rotation measurements, and the constraints on the range of unidentifiable parameters. The importance of rotation measurements is demonstrated in static structural system identification., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Constrained observability techniques for structural system identification using modal analysis

  • Peng, Tian
  • Nogal, María
  • Casas Rius, Joan Ramon
  • Lozano Galant, José Antonio
  • Turmo Coderque, José
The characteristics of civil structures inevitably suffer a certain level of damage during its lifetime and cheap, non-destructive and reliable methods to assess their correct performance are of high importance. Structural System Identification (SSI) using measured response is the way to fine why performance is not correct and identify where the problems can be found. Different methods of SSI exist, both using static and vibration experimental data. However, using these methods is not always possible to decide if available measurements are sufficient to uniquely obtain the unknown. A (SSI) method that uses constrained observability method (COM) has already been developed based on the information provided by the monitoring of static non-destructive tests - using deflections and rotations under a known loading case. The method assures that all observable variables can be obtained with the available measured data. In the present paper, the problem of determining the actual characteristics of the members of a structure such as axial stiffness, flexural stiffness and mass using vibration data is analyzed. Subsets of natural frequencies and/or modal shapes are used. To give a better understanding of the proposed method and to demonstrate its potential applicability, several examples of growing complexity are analyzed, and the results show how constrained observability techniques might be efficiently used for the dynamic identification of structural systems using dynamic data. These lead to significant conclusions regarding the functioning of an SSI method based on dynamic behavior., The authors are indebted to the Spanish Ministry of Economy and Competitiveness for the funding provided through the research projects BIA2013-47290-R and BIA2017-86811-C2-1-R founded with FEDER funds and directed by Professor Jose Turmo and through the research project BIA2017-86811-C2-2-R. It is also to be noted that the part of this work was done included an exchange of faculty financed by the Chinese government to Mrs.Peng thorough the program (No. 201808390083). The financial support from the the Chinese Scholarship Council and the Spanish Ministry of Economy and Competitiveness (BES-2018-B00230) are greatly appreciated., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Structural health monitoring of 2D plane structures

  • Mobaraki, Behnam
  • Ma, Haiying
  • Lozano Galant, José Antonio
  • Turmo Coderque, José
This paper presents the application of the observability technique for the structural system identification of 2D models. Unlike previous applications of this method, unknown variables appear both in the numerator and the denominator of the stiffness matrix system, making the problem non-linear and impossible to solve. To fill this gap, new changes in variables are proposed to linearize the system of equations. In addition, to illustrate the application of the proposed procedure into the observability method, a detailed mathematical analysis is presented. Finally, to validate the applicability of the method, the mechanical properties of a state-of-the-art plate are numerically determined., The authors are indebted to the Spanish Ministry of Economy and Competitiveness for the funding provided through the research projects BIA2013‐47290‐R, BIA2017‐86811‐C2‐1‐R, and BIA2017‐86811‐C2‐2‐R founded with FEDER funds. Funding for this research was provided to Behnam Mobaraki by the Spanish Ministry of Economy and Competitiveness through its program for his PhD. Part of this work was done through grant number 2018‐COB‐9092 from the Universidad de Castilla La Mancha (UCLM). The authors are also indebted to the Secretaria d’ Universitats i Recerca de la Generalitat de Catalunya for the funding provided through Agaur (2017 SGR 1481)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

A novel data acquisition system for obtaining thermal parameters of building envelopes

  • Mobaraki, Behnam
  • Komarizadehasl, Seyedmilad
  • Castilla Pascual, Francisco Javier
  • Lozano Galant, José Antonio
  • Porras Soriano, Rocío
Owing to the high energy consumption in the building sector, appraising the thermal performance of building envelopes is an increasing concern. Recently, a few in situ methodologies to diagnose the thermal parameters of buildings have been considered. However, because of their limitations such as low accuracy, limited number of measurements, and the high cost of monitoring devices, researchers are seeking a new alternative. In this study, a novel hyper-efficient Arduino transmittance-meter was introduced to overcome these limitations and determine the thermal parameters of building envelopes. Unlike conventional methodologies, the proposed transmittance-meter is based on synchronized measurements of different parameters necessary to estimate the transmittance parameter. To verify the applicability of the transmittance-meter, an experimental study was conducted wherein a temperature-controlled box model was thermally monitored, and the outputs of the transmittance-meter employed were compared with those captured by a commercial device. The results revealed a high level of reduction in cost and a low range of difference compared with the latter, thereby validating the applicability of the proposed thermal monitoring system., This research was funded by the Spanish Ministry of Economy and Competitiveness, grant numbers BIA2013-47290-R, BIA2017-86811-C2-1-R, and BIA2017-86811-C2-2-R, and Ministerio de Ciencia Innovación y Universidades: PRE2018-085172., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Shear crack width assessment in concrete structures by 2D distributed optical fiber

  • Rodríguez, Gerardo
  • Casas Rius, Joan Ramon
  • Villalba Herrero, Sergi
This paper outlines the second part of an experimental study to show the capabilities of distributed optical fiber sensors (DOFS) in their application to the structural health monitoring (SHM) of the shear performance of concrete structures. SHM seeks to obtain the shear crack characteristics of concrete elements: detection, localization and quantification of shear damage. The two first were discussed in the first part of the experimental study. In the present paper, the quantification is dealt with by proposing a method to obtain the mean shear crack width in concrete beams. The method is based on the experimental data obtained by a DOFS bonded to the concrete surface. First, the basis of the methodology are presented and, later on, experimentally checked by testing of three partially pre-stressed concrete (PPC) beams subjected to a shear test with increasing level of load. The DOFS were deployed in the web of the beams to conform a 2D grid mesh to measure the strain profile along two orthogonal directions. The experimental data was obtained using an OBR (Optical Backscattered Reflectometer) system with high spatial resolution and sensitivity that allow a complete mapping of the cracking pattern and to obtain the required data for the calculation of the crack width. The results show the feasibility of the proposed method in calculating the shear crack width when compared to the results from traditional instrumentation, Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Safety factor calibration for a new model of shear strength of reinforced concrete building beams and slabs

  • Bairán García, Jesús Miguel
  • Casas Rius, Joan Ramon
When assessing existing structures, the availability of adequate safety factors, calibrated with the most accurate models, and for established target reliability indexes, is of critical importance in order to take the right decision regarding the maintenance/repair/strengthening interventions. In the case of shear resistance in reinforced concrete (RC) structures, when using the current design codes provisions for new constructions in assessment results that, in many cases, existing structures may be considered unsafe, implying large economic costs in strengthening or even dismantling. In this research, a proposal of safety factor relative to a recently developed model for shear strength, for elements with and without transversal reinforcement, based on a reliability-based calibration is presented. A formulation is proposed to determine the adequate strength factor for a selected target reliability index of the existing structure and desired remaining service life by means of a safety factor format, considering the load factors present in the Eurocodes. The calibration is carried out considering typical geometry and load ratios of building floors, as well as normal and high strength concrete. The derived safety factor is almost independent of the chosen remaining service life., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Structural system identification including shear deformation of composite bridges from vertical deflections

  • Emadi, Seyyedbehrad
  • Lozano Galant, José Antonio
  • Xia, Ye
  • Ramos Schneider, Gonzalo
  • Turmo Coderque, José
Shear deformation effects are neglected in most structural system identification methods. This assumption might lead to important errors in some structures like built up steel or composite deep beams. Recently, the observability techniques were presented as one of the first methods for the inverse analysis of structures including the shear effects. In this way, the mechanical properties of the structures could be obtained from the nodal movements measured on static tests. One of the main controversial features of this procedure is the fact that the measurement set must include rotations. This characteristic might be especially problematic in those structures where rotations cannot be measured. To solve this problem and to increase its applicability, this paper proposes an update of the observability method to enable the structural identification including shear effects by measuring only vertical deflections. This modification is based on the introduction of a numerical optimization method. With this aim, the inverse analysis of several examples of growing complexity are presented to illustrate the validity and potential of the updated method., Peer Reviewed, Postprint (author's final draft)