Skip to main content

EVALUACION DE LA CAPACIDAD RESISTENTE FRENTE A ESFUERZOS TANGENTES DE ESTRUCTURAS DE HORMIGON MEDIANTE MODELOS MECANICOS PARA LA EXTENSION DE SU VIDA UTIL

BIA2015-64672-C4-1-R

•
Funding agency name Ministerio de Economía y Competitividad
Funding agency acronym MINECO
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2015
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Management unit Dirección General de Investigación Científica y Técnica
Beneficiary centre UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 75
Encontrada(s) 1 página(s)

RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Application of the Compression Chord Capacity Model to predict the fatigue shear strength of reinforced concrete members without stirrups

  • Cladera, Antoni
  • Ribas, Carlos
  • Oller, Eva
  • Marí, Antonio
The Compression Chord Capacity Model (CCCM), previously developed by the authors with other colleagues, is a simplified model for the shear strength prediction of reinforced and prestressed concrete members with and without transverse reinforcement, with I, T or rectangular cross-section, which represents a useful tool for structural design and assessment in engineering practice. The principal advantage of the application of a mechanical model is the possibility to extend it to different cases, without the need of empirical calibrations. According to the CCCM, the shear strength depends on the concrete tensile strength. In this communication, the CCCM is extended to assess the fatigue shear strength of RC members just incorporating the equation proposed in Model Code 2010 for the concrete tensile fatigue strength. A good performance of the model was observed when analysing the ratio Vtest/Vpred through a previously published database, showing a low scatter (COV 14.7 %).
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Effects of tensile stresses on punching shear strength of RC slabs

  • Fernández, Pablo G.
  • Marí, Antonio
  • Oller, Eva
  • Domingo, Magí
RC slabs can be subjected to transverse loads and tensile in-plane forces, as it occurs in top slabs of continuous bridges under negative moments. Tensile forces can reduce the shear or punching capacity of the slab, aspect not yet studied. A theoretical and experimental investigation has been carried out, in which 10 slabs have been tested under a point load and different degrees of tensile force. The results of five axisymmetrically supported slabs of 1.65x1.65x0.12m are presented. Numerical predictions were made with FEA software ABAQUS and, in addition, the Compression Chord Capacity Mechanical Model CCCM, was extended to account for the effect of in-plane tensile forces. The experimental results showed that the ultimate punching load diminished linearly with the applied tensile force applied and that, after yielding of longitudinal reinforcement such reduction was higher.
RUC. Repositorio da Universidade da Coruña
Publication Artículo científico (JournalArticle)

Ultimate Capacity of Corroded Statically Indeterminate Reinforced Concrete Members

  • Fernández, Ignasi
  • Herrador, Manuel
  • Marí, Antonio
  • Bairan, JM
[Abstract:] The corrosion of steel reinforcement is commonly believed to be the primary cause of structural deterioration of reinforced concrete (RC) structures; as a result of this deterioration, a RC structure can incur a considerable reduction in structural serviceability and safety. Because of their inherent redundancy, statically indeterminate structures develop resistant mechanisms that can potentially assist in delaying the collapse of severely damaged RC structures. In order to experimentally demonstrate these resistant mechanisms, four groups of three two-span continuous RC beam members each were deteriorated using induced corrosion methods and tested to failure under monotonic loads. For control, one group of three RC beams was left uncorroded and similarly load tested. All the RC beam specimens subjected to corrosion demonstrated a significant reduction (a maximum reduction of 55% as compared to the uncorroded control group) of their ultimate capacity. The presence of corrosion induced a transition from flexural failure to anchorage failure in some specimens; despite the induced damage some redistributed structural capacity was observed. Modelling of deterioration effects by the inclusion of different aspects of corrosion was also conducted. Three-dimensional (3D) Finite-Element Method (FEM) models were developed to assess the variation in the mechanical properties of the corroded steel and the reduction in the bond interaction between concrete and steel due to the corrosion of the steel reinforcement. In general, the current 3D FEM models demonstrated a good agreement with the experimental data; however, 3D FEM models that exhibit greater sophistication are necessary to better describe the failure mode of some RC beam specimens when they are associated with local effects., The authors wish to acknowledge the financial support of the European Regional Development Fund (ERDF) and The Ministry of Economy and Competitiveness of the Government of Spain (MINECO) for providing funds for projects BIA2009-11764, BIA2015-64672-C4-1-R, BIA2015-64672-C4-2-R. The financial support of Infrastructures de Catalunya (ICAT) was also highly appreciated.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Embedded Fibre Reinforced Polymer (FRP) reinforcement in concrete structures according to the new version of eurocode 2, Armaduras de polímeros reforzados con fibras (PRF) para estructuras de hormigón en la nueva versión del Eurocódigo 2

  • Oller, Eva
  • Torres, Lluís
  • Diego, Ana de
The new version of Eurocode 2 will include for the first time an informative annex, Annex R “Embedded FRP reinforcement”, to design reinforced concrete structures with fibre reinforced polymer (FRP) reinforcement. FRP embedded reinforcement has some advantages such as their low susceptibility to corrosion, high-strength, and low life-cycle cost. FRP rebars can be used as longitudinal or transverse reinforcement in a similar way than conventional steel rebars. However, in the design of FRP reinforced concrete structures, some particular aspects related to the reinforcement properties must be taken into account, among which it is worth highlighting their linear elastic behaviour until failure, their relatively low modulus of elasticity or their behaviour under sustained stresses. Since, the content of Annex R is new, a summary and background related to all aspects required for designing with FRP reinforcement are given in this paper., Spanish Ministry of Science and Innovation (MCIN/ AEI) and by the European Funds for Regional Development, Peer reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Performance-based slenderness limits for deformations and crack control of reinforced concrete flexural members

  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Torres Llinàs, Lluís
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Barris Peña, Cristina
The use of high strength materials allows flexural members to resist the design loads or to cover long spans with a reduced depth. However, the strict cross section dimensions and reinforcement amount required in ULS are often insufficient to satisfy the serviceability limit states. Due to the complexity associated to a rigorous computation of deflections and cracks width in cracked RC members along their service life, an effective way to ensure the satisfaction of the SLS is to limit the slenderness ratio l/d of the element. In the present study, the slenderness limit concept, previously used for deflection control, is generalized to incorporate the crack width limitations in the framework of structural performance-based design. Equations for slenderness limits incorporating the main parameters influencing the service behaviour of RC members are derived. Cracking and long-term effects are accounted for through simplified coefficients derived from structural concrete mechanics and experimental observations. The proposed slenderness limits are compared with those derived from a numerical non-linear time-dependent analysis for two case studies, and also with those obtained using the EC2 procedure for deflection calculation in terms of constant applied load and constant reinforcement strain. Very good results have been obtained in terms of low errors and scatter, showing that the proposed slenderness limits are a useful tool for performance-based design of RC structures., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Ensayos a cortante y punzonamiento sobre un puente antiguo de hormigón armado sobre el rio Anoia en Gelida, Punching and shear tests on an old reinforced concrete bridge over the Anoia river in Gelida

  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Fernández Sánchez, Pablo Gonzalo|||0000-0002-8237-860X
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Aceña Ramos, Valentín
  • García Vicente, Tomàs
  • Duarte Gómez, Noemí|||0000-0002-4542-8487
Se presentan los estudios llevados a cabo sobre el tablero de un puente de hormigón armado, construido en 1929 en Gelida (Barcelona) sobre el río Anoia, formado por 11 vanos isostáticos de 10,5 m de luz, con vigas sección en ¿, armadas con barras lisas levantadas y cercos. Se han realizado ensayos de cortante sobre vigas en T y de punzonamiento en la losa superior, así como predicciones teóricas de los resultados experimentales. La estructura ha mostrado gran resistencia frente a solicitaciones tangentes y gran rigidez, pese a la heterogeneidad del hormigón, del uso de barras lisas y de la presencia de corrosión local, satisfaciendo los requisitos de seguridad y aptitud al servicio establecidos en las normativas actuales., Este trabajo se ha desarrollado en el contexto del proyecto BIA2015-64672-C4-1-R, financiado por el Ministerio de Economía y Competitividad de España. La Diputación de Barcelona, ha facilitado las vigas ensayadas, así como su corte, manipulación en obra y transporte al laboratorio. El equipo de la UPC agradece enormemente la colaboración de la ingeniera de la Diputación de Barcelona, Maria Josep Palau, de los ingenieros de la empresa constructora Pasquina y de la Dirección de Obra, Sergi Font y José Escudero, entre otros, por su inmensa ayuda, así como a los técnicos del Laboratorio de Tecnología de Estructuras y Materiales de la UPC, Carlos Hurtado, Jordi Cabrerizo y Robert McAloon, por su dedicación y entrega. Finalmente, se agradece a los estudiantes Felipe Baba, Alberto Sarmiento y Raúl Salinas quienes han desarrollado su tesis de Máster en el contexto de este proyecto.
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Strengthening of existing concrete structures with fibre reinforced polymers (FRP) in the new version of Eurocode 2, Refuerzo de estructuras existentes de hormigón con polímeros reforzados con fibras (PRF) en la nueva versión del Eurocódigo 2

  • Oller Ibars, Eva|||0000-0002-0845-3587
  • de Diego, Ana
  • Torres Llinàs, Lluís
  • Madera, Pedro
This  paper  aims  to  introduce  the  content  of  Annex  J  “Strengthening  of  Existing  Concrete  Structures with CFRP” of Eurocode 2 [1]. This is first time that the design of adhesively bonded reinforcement  with  CFRP  has  been  introduced  in  the  European  regulations  through  an  informative annex. Annex J considers two different bonded strengthening techniques: externally bonded reinforcement (EBR) that consists of bonding CFRP strips or sheets to the surface of concrete elements, and near surface mounted reinforcement (NSM) that consists of embedded CFRP strips or rods to the slot cut in the concrete cover. Since, the content of Annex J is new, a summary  and  background  related  to  all  aspects  required  for  designing  CFRP  strengthened  systems for concrete structures, are given in this paper., The authors acknowledge the support provided by Spanish Ministry of Science and Innovation (MCIN/AEI) and by the European Funds for Regional Development in the following projects during their collaboration in the CTN140/SC2 and in the CEN/TC250/SC2/WG1/TG1 (Eva Oller): BIA2015‐64672‐C4‐1‐R, RTI2018‐097314‐B‐C21, and PID2020‐119015GB‐C22., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Analysis of shear resisting actions by means of optimization of strut and tie models taking into account crack patterns

  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Cladera Bohigas, Antoni
The shear resisting actions in reinforced concrete elements without transverse reinforcement is analyzed by means of optimized strut-and-tie models with concrete ties. Biaxial failure criteria are used for uncracked and cracked regions. The stress transfer capacity across cracks is accounted for by including the inclination between the stress field and the crack opening and sliding. An experimental case-study is analyzed. It is shown that that different shear resisting actions can occur in different regions of the beam. The strut-and-tie scheme in the critical region is consistent with the Multi-Action Shear Strength Model (MASM). Analysis of shear resisting actions by means of optimization of strut and tie models taking into account crack patterns., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Assessment of the efficiency of strengthening solutions in concrete structures by means of non-linear step by step analysis models, Evaluación de la eficiencia de soluciones de refuerzo en estructuras de hormigón mediante análisis no lineal evolutivo

  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
  • Oller Ibars, Eva|||0000-0002-0845-3587
When designing a structural strengthening solution, the influence of the previous state of the structure on the capacity of the strengthened structure must be evaluated. In addition, strengthening interventions may involve operations such as partial unloading of the structure, placement and removal of temporary shores, application of loads or pre-deformations, restoring of damaged reinforcement or spalled con-crete or constraining of lateral strains. Therefore, changes in the cross-section geometry and reinforcement, longitudinal scheme, support conditions, loads and state of stresses and strains, may take place. Furthermore, occurrence of phenomena producing a premature failure or a change in the failure mode, should be avoided. In order to account for such a large variety of causes and phenomena affecting the structural response, a nonlinear and time-dependent analysis model of 3D reinforced and prestressed concrete frames, capable of capturing different failure modes and taking into account the structural history, is described. The model has been verified with tests on strengthened structures available in the literature and has been applied to an actually remodeled structure, comparing the advantages and disadvantages of two different strengthening proposals, showing its capabilities to assess the efficiency of structural strengthening systems., This paper is dedicated to the memory of an extraordinary engineer and human being, Luis Ortega Basagoiti, who was an example and reference for structural engineers and researchers along his professional career. The works described in this paper have been developed in the framework of the following research projects funded by the Spanish Science and Technology Ministries and by the European Funds for Regional Development, ADRESS (BIA2009-11764), REHABCAR (IPT-370000-2010-029), HORVITAL (BIA2015-64672-C4-1-R) and STRADURAVIUS (RTI2018-097314-B-C21)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Theoretical prediction of the punching shear strength of concrete flat slabs under in-plane tensile forces

  • Fernández Sánchez, Pablo Gonzalo|||0000-0002-8237-860X
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Oller Ibars, Eva|||0000-0002-0845-3587
RC slabs can be subjected simultaneously to transverse loads and in-plane tensile forces, as it happens in top slabs of continuous box girder bridges decks, in the regions of negative moments, or in flat slabs subjected to horizontal loads, produced by wind or earth pressure. Tensile forces can reduce the shear punching capacity of slabs. However, few studies have been carried out to quantify this effect. With this purpose, a mechanical model has been developed to capture the influence of in-plane tensile forces on the punching shear strength and verified with punching tests under different in-plane tensile load levels. The model, presented in this paper, consists of an extension of the Punching shear Compression Chord Capacity Model to account for the effects of tensile forces on the resisting actions. A linear reduction of the punching shear strength as a function of the external load applied has been obtained for moderate tensile forces, whereas high level of tensile forces may produce premature yielding of the reinforcement and further reduction of the punching shear strength. The proposed model accurately captures the available test results, including the effects of the premature yielding of reinforcement when the tensile force produces concrete cracking. In addition, predictions of punching-shear-tensile tests available in the literature were made with different theoretical models included in design codes, which yielded in general conservative results and showed high scatter., This work was developed in the framework of Research Project BIA-2015-64672-C4-1-R, financed by the Ministry of Economy and Competitiveness (MINECO) of Spain and the European Funds for Regional Development (FEDER). The authors want to thank Mr. José Romo, from FHECOR Engineering, for transmitting his experience in bridge design that helped to set the problem and to the director and technicians of the Structural Technology Laboratory of UPC, for their help in carrying out the experimental campaign., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Shear fatigue strength of reinforced concrete members without transverse reinforcement according to the compression chord capacity model

  • Cladera Bohigas, Antoni
  • Ribas González, Carlos Rodrigo
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
Although the shear fatigue behaviour of elements without shear reinforcement has been studied for a while, there is still a need for a simple mechanical model that evaluates the shear fatigue strength. The Compression Chord Capacity Model (CCCM), previously developed by the authors, is a simplified model for the shear strength prediction of reinforced and prestressed concrete members with and without transverse reinforcement, with I, T or rectangular cross-sections. This model represents a useful tool for structural design and assessment in engineering practice. In this paper, the CCCM has been extended to assess the fatigue shear strength of RC elements. This extension is consistent since the existing observed fatigue failure modes show similarities with the initial assumption of the model, which considers that the member shear strength is controlled by the shear capacity of the flexural compression chord. Three different approaches to take into account the influence of the fatigue have been combined with the CCCM. In general, a good performance of the model combined with the three different approaches was observed when analysing the ratio Vtest/Vpred through a database of 87 tests previously published by other authors, showing a low scatter (<15%) and a significant safety given by the minimum ratio and the 5th percentile., The authors want to acknowledge the financial support provided by the Spanish Ministry of Economy and Competitiveness (MINECO) and the European Funds for Regional Development (FEDER), through research projects: BIA2015-64672-C4-3-R and BIA2015-64672-C4-1-R. The authors also want to thank to Dr. Miguel Fernández-Ruiz for providing the authors the fatigue shear tests database., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Simplified tests to study the size effect of the compression chord in beams under shear forces: application of DIC methodology, Ensayos en probetas para el estudio del efecto tamaño en la cabeza de compresión de vigas sometidas a esfuerzo cortante: aplicación de la metodología DIC

  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Barris Peña, Cristina
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Torres Llinàs, Lluís
  • Santander, Andres
To evaluate how the size effect affects the stresses developed along the compression chord in a beams subjected to shear forces, a simplified experimental program was developed on 50 prismatic specimens subjected to a splitting test. The studied parameters were: dimensions, slenderness, concrete compressive strength, and maximum aggregate size. To capture the post-peak behavior of the concrete, the load was introduced as a function of the crack width, through appropriate control algorithms. Digital Image Correlation (DIC) in a 2D configuration has also been used to accurately capture the formation, width and propagation of cracks to corroborate the experimental measurements., The financial support provided by the Spanish Ministry of Economy and Competitiveness (MINECO) and the European Funds for Regional Development (FEDER), through the Research projects: BIA2015-64672-C4-1-R and BIA2017-84975-C2-2-P and through the Excellence network BIA2015-71484-REDT.
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Evaluación del tiempo de recuperación de edificios de concreto reforzado dañados por sismo

  • Gutiérrez, Juan Jesús
  • Ayala, A. Gustavo
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
Sismos recientes han demostrado la importancia de evaluar el tiempo que tardarían los edificios dañados en ser reparados, ocupables y funcionales nuevamente, debido a que el tiempo de inactividad puede generar pérdidas económicas e implicaciones sociales importantes. En este trabajo se presenta una metodología para evaluar el tiempo de recuperación en términos probabilistas de edificios que han sido dañados por sismo. El esquema de evaluación propuesto se basa en el método PERT y es consistente con el esquema de evaluación sísmica propuesto por el PEER y con el concepto de resiliencia desarrollado por el MCEER. Se presenta la evaluación de un edificio de concreto reforzado en el que se incluyen los muros de mampostería no reforzada. Recent earthquakes have demonstrated the importance of assessing the time it would take for damaged buildings to be repaired, occupied and functional again, because downtime can lead to significant economic losses and social implications. This paper presents a methodology to evaluate the recovery time in probabilistic terms of buildings that have been damaged by earthquakes. The proposed evaluation scheme is based on the PERT method and is consistent with the seismic evaluation scheme proposed by PEER and with the concept of resilience developed by the MCEER. The evaluation of a reinforced concrete building is presented, in which the infill unreinforced masonry walls are included.
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Efficiency of shear strengthening of RC beams with externally bonded FRP materials: state-of-the-art in the experimental tests

  • Kotynia, Renata
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Kaszubska, Monika
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
This paper presents a study of the shear capacity of reinforced concrete (RC) beams strengthened in shear with externally bonded (EB) fiber reinforced polymer (FRP) composites, based on the performance of existing published tests. The main objective of this study is to create a comprehensive overview of the performance of different shear strengthening configurations and the failure modes observed in experimental tests. In addition, the influence of the following parameters on the strengthening efficiency has been analyzed: shear span to depth ratio (a/d), existing steel transverse reinforcement ratio (ρsw), concrete strength (fck), size effect (d), longitudinal reinforcement ratio (ρsL), strengthening configurations, type of FRP: sheets or laminates (CFRP, GFRP), and FRP axial stiffness (AfEf)., This paper has been developed under the framework of the Research Projects “BIA2015‐64672‐C4‐1‐R” and “RTI2018‐097314‐BC21” funded by the Spanish Ministry of Economy and Competitiveness (MINECO) and co‐funded by the European Regional Development Funds (ERDF). The authors would also like to thank the Cost Action TU1207 which funded a short term scientific mission of the second author in Lodz University of Technology., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Effects of tensile stresses on punching shear strength of RC slabs

  • Fernández Sánchez, Pablo Gonzalo|||0000-0002-8237-860X
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Domingo Tarancón, Magí|||0000-0002-5403-5204
RC slabs can be subjected to transverse loads and tensile in-plane forces, as it occurs in top slabs of continuous bridges under negative moments. Tensile forces can reduce the shear or punching capacity of the slab, aspect not yet studied. A theoretical and experimental investigation has been carried out, in which 10 slabs have been tested under a point load and different degrees of tensile force. The results of five axisymmetrically supported slabs of 1.65x1.65x0.12m are presented. Numerical predictions were made with FEA software ABAQUS and, in addition, the Compression Chord Capacity Mechanical Model CCCM, was extended to account for the effect of in-plane tensile forces. The experimental results showed that the ultimate punching load diminished linearly with the applied tensile force applied and that, after yielding of longitudinal reinforcement such reduction was higher., Los autores desean agradecer la financiación recibida del Ministerio de Ciencia e Innovación y de los Fondos Europeos de Desarrollo Regional (FEDER) a través del proyecto “Evaluación de la capacidad resistente frente a esfuerzos tangentes de estructuras de hormigón mediante modelos mecánicos para la extensión de su vida útil” BIA2015-64672-C4-1-R . Así mismo desean agradecer el apoyo del Laboratorio de Tecnologia de Estructuras y Materiales de la UPC y de todos los técnicos que han contribuido a la realización de esta campaña experimental y sin cuya ayuda no habría sido posible.
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

A punching shear mechanical model for reinforced concrete flat slabs with and without shear reinforcement

  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Cladera Bohigas, Antoni
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
A punching shear strength mechanical model for RC flat slabs with and without shear reinforcement, based on a beam shear model previously developed by the authors, is presented. The differences in resisting actions between beam shear and punching shear have been identified and incorporated into the governing equations and failure modes, resulting in simple but accurate punching design equations. The model consistently explains and quantifies some experimentally observed phenomena, such as the higher contribution of the concrete to the punching shear strength of slabs than in the case of beams subjected to shear, mainly due to the multi-axial state of stresses that takes place near the support. Furthermore, the model provides physical meaning to some parameters used in the design, such as the position of the critical perimeter or the effective stress of the punching reinforcement, among others. Very good agreement has been obtained between the model predictions and the results of 560 punching tests of concentrically loaded slabs, with and without shear reinforcement, included in two available large databases. The mechanical character of the model allows its extension to post-tensioned flat slabs, border or corner columns, steel fiber and FRP reinforced concrete slabs or different strengthening systems in a consistent way., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Influence of the flanges width and thickness on the shear strength of reinforced concrete beams with T-shaped cross section

  • Ayensa Pardo, Alberto
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Beltrán, Beatriz
  • Ibarz Montaner, Elena
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Gracia Villa, Luis
Shear design of reinforced concrete beams with T section considers only the contribution of the web, mainly provided by aggregate interlock. However, as the load increases and large web crack openings take place, aggregate interlock reduces and shear stresses tend to concentrate near the neutral axis, usually located in the flanges of T beams, whose contribution to shear strength may be not negligible, as it has been experimentally observed. Thus, the contribution of flanges may drive to considerable cost savings in new structures and may become decisive when evaluating the shear capacity of existing structures. To quantify such contribution, a nonlinear 3D-FEA model has been developed and calibrated with the results of shear tests performed on RC T-beams by the authors. Once adjusted, the model has been used to analyze the shear response of beams with different geometry and longitudinal reinforcement, usual in practice. It has been found that, up to certain limits, the contribution of the flanges to the shear strength increases as the amount of longitudinal reinforcement decreases, as the flanges width increases and as the flange thickness increases. The maximum contribution of flanges found in the present study is 31.3% of the total shear resisted. Furthermore, the numerical model has been used to visualize and quantify aspects that are not easy to obtain experimentally, such as the distribution of the shear stresses between the web and the flanges. The present study will contribute to derive a design expression for the shear effective flanges width of T beams., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Assessment of the existing models to evaluate the shear strength contribution of externally bonded FRP shear reinforcements

  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Kotynia, Renata
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
This paper presents an analysis of the performance of different existing formulations to quantify the FRP contribution to the shear strength of RC elements strengthened in shear by externally bonded FRP sheets. A large database of 555 tests has been assembled distinguishing between the shape of the section, the existence of internal transverse reinforcement and the FRP configurations. In general, predictions are more conservative for beams without transverse reinforcement. In addition, in some cases predictions are unsafe for beams with transverse reinforcement, showing a possible interaction with the internal transverse reinforcement which is not considered in the experimental FRP contribution to the shear strength. For wrapped FRP configurations, models generally assumed failure at the bottom corner of the section and results are very conservative in some cases where failure was experimentally observed along the web. For U-shaped and side-bonded configuration, results depend mainly on the assumed bond model and are more accurate than in the previous case, showing for some models unsafe predictions for the continuous FRP system applied in beams with transverse reinforcement., This paper has been developed under the framework of the Research Projects “BIA2015-64672-575 C4-1-R” and “RTI2018-097314-B-C21” funded by the Spanish Ministry of Economy and Competitiveness (MINECO) and co-funded by the European Regional Development Funds (ERDF). The authors would also like to thank the Cost Action TU1207 which funded a short term scientific mission of the first author in Lodz University of Technology., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Crack detection in concrete elements from RGB pictures using modified line detection kernels

  • Sánchez Calderón, Luis
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
Cracking is inevitable in ordinary reinforced concrete construction, yet it should be controlled to guarantee adequate serviceability and durability. Crack patterns analysis is essential for diagnosis, monitoring and maintenance, to identify malfunctioning or unsafe situations. An important part of this state is the cracking pattern of the elements as an indicator of the tensional distribution in the concrete. A method to search and measure fissures in RGB images of concrete elements has been developed and implemented as a MATLAB script. The algorithm uses several digital image processing tools to detect the measure, the cracks width and orientation; featuring these tools are the spatial filters called “orientation kernels” developed especially for detecting the angle and width of the cracks.
UPCommons. Portal del coneixement obert de la UPC
Publication Capítulo o parte de un libro (BookPart)

SP-357—8: Punching-shear strength of reinforced concrete slabs subjected to concentric transverse loads and in-plane tensile forces

  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Fernández Sánchez, Pablo Gonzalo|||0000-0002-8237-860X
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Cladera Bohigas, Antoni
Reinforced concrete slabs can be subjected simultaneously to transverse loads and in-plane tensile forces, as it occurs in top slabs of continuous box girder bridges at intermediate supports, or in flat slabs supported on columns, subjected to horizontal loads. To study the effects of in-plane forces in the slab punching-shear strength, an experimental and theoretical investigation was carried out, which is described in this paper. Five square slabs of 1650 mm (42”) side and 120 mm (4.7”) thickness were tested under a centered transverse point load and different degrees of uniaxial in-plane tensile force. Numerical predictions using non-linear finite element analyses were performed to help in the experiments design. Furthermore, the punching-shear mechanical model, Compression Chord Capacity Model (CCCM), was extended to incorporate the effects of in-plane tensile forces. The experimental results showed that the punching strength linearly decreases with the level of applied tensile force and, if cracking in the slabs is produced by the tensile force, yielding of the reinforcement and further reduction may take place. Excellent agreement was found between theoretical predictions and tests results. Furthermore, the CCCM was verified with available results of punching tests with uniaxial and biaxial tensile forces, obtaining very good results., This work has been carried out within the framework of research projects BIA-2015-64672-C4-1-R, and BIA2015- 64672-C4-3-R financed by the Ministry of Economy and Competitiveness (MINECO) of Spain, and also with the financial support of the Government of Catalonia through the contract for research and innovation in infrastructures E1-INF-18500. The authors want to deeply thank also the personnel of the Structural Technology Laboratory of the Universitat Politècnica de Catalunya.
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Application of the Compression Chord Capacity Model to predict the fatigue shear strength of reinforced concrete members without stirrups

  • Cladera Bohigas, Antoni
  • Ribas González, Carlos Rodrigo
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
The Compression Chord Capacity Model (CCCM), previously developed by the authors with other colleagues, is a simplified model for the shear strength prediction of reinforced and prestressed concrete members with and without transverse reinforcement, with I, T or rectangular cross-section, which represents a useful tool for structural design and assessment in engineering practice. The principal advantage of the application of a mechanical model is the possibility to extend it to different cases, without the need of empirical calibrations. According to the CCCM, the shear strength depends on the concrete tensile strength. In this communication, the CCCM is extended to assess the fatigue shear strength of RC members just incorporating the equation proposed in Model Code 2010 for the concrete tensile fatigue strength. A good performance of the model was observed when analysing the ratio Vtest/Vpred through a previously published database, showing a low scatter (COV 14.7 %)., Esta investigación se ha desarrollado en el marco de dos proyectos cofinanciados por la Agencia Estatal de Investigación y Fondos FEDER: BIA2015-64672-C4-3-R y BIA2015-64672-C4-1-R.
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Performance-based slenderness limits for deflections and reinforcement stresses control in RC beams, Límites de esbeltez basados en prestaciones para vigas de hormigón armado para el control de deformaciones y el control de tensiones en la armadura

  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Torres Llinàs, Lluís
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Barris Peña, Cristina
Due to the complex deformational behavior of cracked RC members, an effective way to ensure the fulfilment of the SLS is to limit the slenderness ratio l/d of the element. In this study, the deformation slenderness limit concept is generalized to incorporate crack width limitations. The proposed slenderness limits are compared with those derived from non-linear time-dependent analysis and also with those obtained using the EC2 method of deflections interpolation. Very good approximation and low scatter has been obtained showing that the proposed slenderness limits are a useful tool for performance-based design of RC structures., The financial support provided by the Spanish Ministry of Economy and Competitiveness (MINECO) and the European Funds for Regional Development (FEDER), through the Research projects: BIA2015-64672-C4-1-R and BIA2017-84975-C2-2-P and through the Excellence network BIA2015-71484-REDT
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Theoretical prediction of the shear strength of reinforced concrete slabs under concentrated loads close to linear supports

  • Fernández Sánchez, Pablo Gonzalo|||0000-0002-8237-860X
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Oller Ibars, Eva|||0000-0002-0845-3587
A mechanical model has been developed by the authors in order to predict the shear strength of reinforced concrete slabs under concentrated loads close to linear supports. Such situation takes place very often in bridge slabs and cantilever sections of bridge decks under concentrated heavy vehicle loads. The model takes into account a significant number of variables involved in the phenomenon, such as the clear shear span, the concrete compressive strength, the reinforcement ratio, the effective depth, the load spreading angle, the size effect and the size of the loaded area. It is applicable to simply supported slabs, cantilever slabs and situations with partial restraint to the rotation, such as intermediate supports. It has been validated with a database of 90 shear test in slabs subjected to a single concentrated load in different supporting conditions, yielding results on the safe side and showing low scatter. A parametric analysis of the model is also presented, detailing how the different involved variables affect the shear strength. These results, along with the simplified expressions developed for the shear strength calculation, provide a useful tool for the assessment of the shear strength of RC solid slabs in daily engineering., This work was developed in the framework of Research Project BIA-2015-64672-C4-1-R, financed by the Ministry of Economy and Competitiveness (MINECO) of Spain and the European Funds for Regional Development (FEDER). The authors want to thank Ph.D candidate Alex Micael Dantas de Sousa, from the University of Sao Paulo, and Prof Eva Lantsoght from Tecnische Universiteit of Delft, for sharing the up-to-date database of shear test on RC slabs, which has facilitated the development and validation of the proposed mechanical model., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Ultimate capacity of corroded statically indeterminate reinforced concrete members

  • Fernández Pérez, Ignacio
  • Herrador Barrios, Manuel F.
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
The corrosion of steel reinforcement is commonly believed to be the primary cause of structural deterioration of reinforced concrete (RC) structures; as a result of this deterioration, a RC structure can incur a considerable reduction in structural serviceability and safety. Because of their inherent redundancy, statically indeterminate structures develop resistant mechanisms that can potentially assist in delaying the collapse of severely damaged RC structures. In order to experimentally demonstrate these resistant mechanisms, four groups of three two-span continuous RC beam members each were deteriorated using induced corrosion methods and tested to failure under monotonic loads. For control, one group of three RC beams was left uncorroded and similarly load tested. All the RC beam specimens subjected to corrosion demonstrated a significant reduction (a maximum reduction of 55% as compared to the uncorroded control group) of their ultimate capacity. The presence of corrosion induced a transition from flexural failure to anchorage failure in some specimens; despite the induced damage some redistributed structural capacity was observed. Modelling of deterioration effects by the inclusion of different aspects of corrosion was also conducted. Three-dimensional (3D) Finite-Element Method (FEM) models were developed to assess the variation in the mechanical properties of the corroded steel and the reduction in the bond interaction between concrete and steel due to the corrosion of the steel reinforcement. In general, the current 3D FEM models demonstrated a good agreement with the experimental data; however, 3D FEM models that exhibit greater sophistication are necessary to better describe the failure mode of some RC beam specimens when they are associated with local effects., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Resistencia a punzonamiento de losas de hormigón armado sometidas a tracciones en su plano, Punching strength of reinforced concrete slabs subjected to in-plane tensile forces

  • Fernández Sánchez, Pablo Gonzalo|||0000-0002-8237-860X
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Duarte Gómez, Noemí|||0000-0002-4542-8487
Se presentan los resultados de un estudio teórico y experimental de la resistencia a punzonamiento de placas sometidas a tracciones en su plano. Se han ensayado 10 losas de 1,65 x 1,65 x 0,12 metros, con dos cuantías diferentes de armadura, apoyadas en ocho puntos, sometidas a diversos niveles de tracción. Se observó que la carga última disminuye linealmente con la tracción aplicada, si bien, a partir de la plastificación de la armadura de flexión longitudinal, esta reducción es mayor. Las predicciones mediante modelos numéricos y mediante el modelo mecánico CCCM de resistencia a punzonamiento proporcionaron una excelente concordancia con los resultados experimentales., Los autores desean agradecer la financiación recibida del Ministerio de Ciencia e Innovación y de los Fondos Europeos de Desarrollo Regional (FEDER) a través del proyecto “Evaluación de la capacidad resistente frente a esfuerzos tangentes de estructuras de hormigón mediante modelos mecánicos para la extensión de su vida útil” BIA2015-64672-C4-1-R . Así mismo desean agradecer el apoyo del director del Laboratorio de Tecnología de Estructuras y Materiales de la UPC, de los técnicos y de los estudiantes de Master Magí Domingo y Laura Beltrán, quienes han contribuido a la realización de esta campaña experimental.
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Experimental investigation of the shear strength of one-way reinforced concrete (RC) slabs subjected to concentrated loads and in-plane transverse axial tension

  • Fernández Sánchez, Pablo Gonzalo|||0000-0002-8237-860X
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Oller Ibars, Eva|||0000-0002-0845-3587
This paper presents the results of an experimental campaign carried out to investigate the effects of in-plane transverse tensile forces on the shear strength of linearly supported one-way reinforced concrete (RC) slabs without shear reinforcement subjected to concentrated loads. A total of 5 half scale slabs (1650¿×¿1650¿×¿120¿mm), subjected simultaneously to different levels of in-plane tensile forces and a concentrated load were tested up to failure. The clear shear span to effective depth ratio av/d was equal to 3 in all tests, to minimize the effects of the direct transmission of the load to the closest support, the so called arching action. As observed, the shear strength barely decreases with increasing values of the tensile force applied, even for values of the external force that cracked the concrete cross-section of the slabs in the direction perpendicular to the span. These observations may indicate that the shear–flexural behavior in the spanning direction is not significantly affected by the membrane forces in the transverse direction., This work has been carried out within the framework of the research project BIA-2015-64672-C4-1-R, financed by the Ministry of Economy and Competitiveness (MINECO) of Spain, and with the invaluable help of the technicians and the director of the Laboratory of Technology of Structures and Materials of the Universitat Politècnica de Catalunya. The authors want also to thank Master students Pau Figueras and Laura Beltran who collaborated in the numerical predictions and execution of the tests, respectively., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Punching-shear strength of reinforced concrete slabs subjected to unidirectional in-plane tensile forces

  • Fernández Sánchez, Pablo Gonzalo|||0000-0002-8237-860X
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Oller Ibars, Eva|||0000-0002-0845-3587
This is the peer reviewed version of the following article: [Fernández, PG, Marí, A, Oller, E. Punching‐shear strength of reinforced concrete slabs subjected to unidirectional in‐plane tensile forces. Structural Concrete. 2020; 1– 16. https://doi.org/10.1002/suco.202000112], which has been published in final form at https://doi.org/10.1002/suco.202000112. This article may be used for non-commercial purposes in accordance with Wiley Terms and Conditions for Self-Archiving., Some reinforced concrete slabs are subjected simultaneously to concentrated loads and unidirectional in‐plane tensile forces. This the case of the top slab of a box girder bridge where hogging bending moments take place at the intermediate supports. Then, the in‐plane tensile forces may reduce the punching‐shear strength under concentrated loads. This paper describes an experimental campaign carried out to investigate the effect of unidirectional in‐plane tensile forces on the punching‐shear strength of RC slabs. A total of, five slabs (1,650 × 1,650 × 120 mm), subjected to different levels of in‐plane tensile forces were tested under a concentrated load up to failure. As observed, the punching‐shear strength diminishes almost linearly as the tensile force increases, up to a certain point associated to concrete cracking. From that point on, the reduction of punching strength is larger since the tensile force at the crack must be resisted by the reinforcement, which yields prematurely., This work has been carried out within the framework of the research project BIA-2015-64672-C4-1-R, financed by the Ministry of Economy and Competitiveness (MINECO) of Spain, and with the invaluable help of the technicians and the director of the Structural Technology Laboratory of the Polytechnic University of Catalonia. The authors want also to thank Master students Magí Domingo and Laura Beltran who collaborated in the numerical predictions and execution of the tests, respectively., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Effects of unidirectional tensile stresses on punching shear strength of RC slabs

  • Fernández Sánchez, Pablo Gonzalo|||0000-0002-8237-860X
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Domingo Tarancón, Magí|||0000-0002-5403-5204
RC slabs can be subjected to transverse loads and in-plane tensile forces simultaneously, as it occurs in top slabs of continuous box girder bridges at intermediate supports, or in floor slabs supported on columns and subjected to horizontal forces, due to skew in-plane compressions. Tensile forces can reduce the punching capacity of the slabs, aspect not studied yet. An experi-mental, numerical and theoretical investigation has been carried out, in which 5 1.65x1.65x0.12 m slabs have been tested under a point load and different degrees of unidirectional tensile force. Numerical predictions were made with FEA software ABAQUS and, from the theoretical point of view, the Compression Chord Capacity Model (CCCM) was extended to take into account the effect of in-plane tensile forces in the punching strength of the slabs. The experimental results showed that the ultimate punching load decreases linearly with the applied tensile force, and if that tensile force cracks the slabs, such reduction is higher. Results obtained with FEA and CCCM are in agreement with the observations made at the laboratory, This work has been carried out within the framework of research project BIA-2015-64672-C4-1-R, financed by the Ministry of Economy and Competitiveness (MINECO) of Spain. The authors want o deeply thank the personnel of the Structural Technology Laboratory of the Polytechnic University of Catalonia and Master student Laura Beltrán who collaborated in the execution of the tests.
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

B-spline sectional model for general 3D effects in reinforced concrete elements

  • Poliotti, Mauro
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
In this paper, an efficient sectional model for the nonlinear analysis of reinforced concrete elements sensible to 3D stress-components effects is presented. The classic plane-sections kinematic hypothesis is enhanced with a warping-distortion displacement field, which enables the model to reproduce the interaction between normal and tangential forces. The complementary field is obtained explicitly considering the inter-fiber equilibrium. This is solved using b-splines interpolation on the cross-section domain. The proposed method significantly reduces the number of unknowns compared with a finite element solution. The model is able to reproduce the interaction of longitudinal and transverse reinforcement with the concrete matrix. The validation shows that the presented model reproduces accurately complex failure modes as pure shear and coupling between bending and torsion. Further, as the transverse reinforcement is considered explicitly, confinement can be simulated in an objective manner. The presented model is an efficient tool for nonlinear analysis of reinforced concrete sections under general loading., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Shear strength of non-slender reinforced concrete beams

  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
  • Menduiña Montero, Raul
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Cladera Bohigas, Antoni
Shear strength of non-slender reinforced concrete beams, in which a/d¿ 2.5, is enhanced due to arching action. Current shear design methods for such elements, including the Strut-and-Tie Method (STM), show deviations with respect to tests results. In this paper, a shear strength mechanical model developed for slender beams is extended to non-slender beams. The effects of the non-planar strains distribution, of the multi-compression stress state generated near the applied load, and those of the pre-determined position and inclination of the critical shear crack are incorporated in the model formulation. The predictions of the proposed model have been compared with those obtained using the STM following the ACI and FIP recommendations and the EC2 simplified proposal. Three previously published databases, including the results of 486 shear tests of non-slender beams with and without web reinforcement, have been considered. The predictions by the proposed model resulted in better precision and less scatter, for all subset of tests, while the proposed method is direct and simpler for daily engineering purposes., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

A new concrete plastic-damage model with an evolutive dilatancy parameter

  • Poliotti, Mauro
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
Typical plastic-damage models for concrete use a constant dilatancy parameter. On problems sensitive to confinement and shear softening, this parameter needs ad hoc calibration to fit experimental observations. This makes the model not objective for general applications. To overcome this issue, in this paper, a constitutive plastic-damage model with evolutive dilatancy is proposed for concrete. The evolution of dilatancy is made dependent on the plastic-damage and stress states. The proposed evolution law is validated by comparison of numerical simulations with available experimental results. The validation includes: concrete specimens under uniaxial compression measuring the free expansion, passively confined concrete specimens with different confining materials, and reinforced concrete panels under in-plane shear. It is concluded that the model accurately reproduces concrete lateral expansion through different nonlinear states. Proper modeling of concrete nonlinear expansion proves essential for capturing the response in a number of situations: softening under high shear stresses, confinement, and ductility assessment., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Mechanical model for the shear strength of steel fibers reinforced concrete beams (SFRC) without stirrups, Modelo mecánico para la resistencia a cortante de vigas de hormigón armado reforzado con fibras, sin armadura de cortante

  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Spinella, Nino
  • Recupero, Antonino
  • Cladera Bohigas, Antoni
Despite the numerous studies made showing that the addition of steel fibres to concrete enhances the shear strength of RC beams, current design formulations are still empirical and present large scatter in front of the test results. In this paper, the previously developed Multi-Action Shear Model is extended to SFRC beams without stirrups, adopting an analytical formulation to evaluate the residual tensile stress of SFRC and incorporating the effects of the crack bridging capacity of SFRC in the shear resisted trough the different shear-transfer mechanisms. The proposed model predicts the tests results included in a recently published database with 448 shear tests with less scatter than any of the existing models., The financial support provided by the University of Messina (Italy), through the scholarship granted for a two-months research and teaching stage of the first author, is acknowledged. This work is part of the Research Projects BIA2015-64672-C4-1-R, funded by the Spanish Ministry of Economy and competitiveness, and RTI2018-097314-B-C21, funded by the Spanish Ministry of Science and Innovation.
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

A variable order framework for 3D nonlinear analysis of reinforced concrete frames under general loading

  • Poliotti, Mauro
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
  • Moller, O.
A framework for the analysis of three-dimensional reinforced concrete frame structures, capable of reproducing general failure modes, is presented. A force-based model which guarantees the equilibrium between nodal and sectional forces is enhanced by means of a cross-sectional model. It is capable of capturing the complex coupling between all the internal forces. Consequently, different failure modes can be reproduced such as shear, torsional, flexural or axial failures. Material modeling of concrete is made using a plastic-damage model that incorporates a variable dilatancy parameter. The sectional and constitutive models are implemented in OpenSees. The sectional model can be used at each integration point of the force-based element. Alternatively, it can be used only where high coupling between the internal forces is expected, producing a variable order structural model. The validation shows that the frame element is capable of accurately reproduce beams and columns under monotonic and cyclic loads. The framework presented is a powerful numerical instrument for the analysis, design and assessment of reinforced concrete buildings and bridges., The first and second authors acknowledge the support provided by Spanish Ministry of Economy, Industry and Competitiveness and the European Regional Development Fund (ERDF), through the projects BIA2015-64672-C4-1R, BIA2012-36848 and RTI2018-097314-B-C21. The first author acknowledges the support of the Catalan Agency for University and Research through doctoral scholarship 2018FI-B1-00103. The third author acknowledges the support of the Research Council of Universidad Nacional de Rosario (CIUNR) and the Science and Technology Secretariat (SECyT), through the project 1ING601., Peer Reviewed, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura::9.1 - Desenvolupar infraestructures fiables, sostenibles, resilients i de qualitat, incloent infraestructures regionals i transfrontereres, per tal de donar suport al desenvolupament econòmic i al benestar humà, amb especial atenció a l’accés assequible i equitatiu per a totes les persones, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura::9.a - Facilitar el desenvolupament d’infraestructures sostenibles i resilients als països en desenvolupament per mitjà de més suport financer, tecnològic i tècnic als països africans, països menys avançats, països en desenvolu­pament sense litoral i petits estats insulars en desenvolupament, Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles, Objectius de Desenvolupament Sostenible::13 - Acció per al Clima::13.1 - Enfortir la resiliència i la capacitat d’adaptació als riscos relacionats amb el clima i els desastres naturals a tots els països, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura, Objectius de Desenvolupament Sostenible::13 - Acció per al Clima, Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles::11.b - Per a 2020, augmentar substancialment el nombre de ciutats i assentaments humans que adopten i posen en marxa polítiques i plans integrats per promoure la inclusió, l’ús eficient dels recursos, la mitigació del canvi climàtic i l’adaptació a aquest, així com la resiliència davant dels desastres, i desenvolupar i posar en pràctica una gestió integral dels riscos de desastre a tots els nivells, d’acord amb el Marc de Sendai per a la reducció del risc de desastres 2015.2030, Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles::11.5 - Per a 2030, reduir de forma significativa el nombre de morts causades per desastres, inclosos els relacio­nats amb l’aigua, i de persones afectades per aquests, i reduir substancialment les pèrdues econòmiques directes causades per desastres relacionades amb el producte interior brut mundial, fent un èmfasi especial en la protecció de les persones pobres i de les persones en situacions de vulnerabilitat
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Detección y medición semiautomática de fisuras en elementos de hormigón en fotos digitales usando procesamiento de imágenes

  • Sánchez Claderón, Luis
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
La fisuración es inevitable en las obras de hormigón armado, pero debe de ser controlada para asegurar un adecuado comportamiento en servicio y por durabilidad. El análisis de los patrones de fisuración es una parte esencial en el diagnóstico, monitorización y mantenimiento; para identificar deficiencias o situaciones comprometidas. Por otro lado, el patrón de fisuración también puede ser un indicador de la distribución tensional del hormigón y de los esfuerzos determinantes en una zona. En este artículo se presente un nuevo método para la búsqueda y medición de fisuras en imágenes en color de elementos de hormigón. El algoritmo usa diversas herramientas de procesamiento digital de imágenes para medir la orientación de las fisuras y entre estas herramientas destaca un tipo especial de filtros llamados “orientation kernels” desarrollados especialmente para detectar el ángulo y ancho de las fisuras., Esta investigación es parcialmente apoyada por los proyectos BIA2012-36848 “Performance-based design of partially prestressed concrete structures ”, y BIA2015-64672-C4-1-R “Contribution to the extension of service lifetime of existing concrete structures through an adequate structural evaluatio n and strengthening with advanced materials” , financiados a su vez por el Ministerio Economía, 14/14 Industria y Competitividad de España y por los Fond os Europos de Desarrollo Regional (FEDER). También se debe mencionar el financiamiento por par te de la Secretaria de Educación Superior, Ciencia, Tecnología y Educación (SENECYCT) (insituc ión del gobierno ecuatoriano) a través de una beca de “Convocatoria Abierta” para programas d e Masters y Phd., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Mechanical model for the shear strength of steel fiber reinforced concrete (SFRC) beams without stirrups

  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Spinella, Nino
  • Recupero, Antonino
  • Cladera Bohigas, Antoni
The final publication is available at Springer via http://dx.doi.org/10.1617/s11527-020-01461-4., Numerous studies have shown that adding steel fibers to the concrete mixture improves both the shear strength and ductility of reinforced concrete beams. Most current shear design formulations for steel fiber reinforced concrete beams are empirically based and their predictions provide acceptable results when compared with tests results, but only in limited ranges of the parameters involved. On the other hand, many shear theoretical models suggested in the literature are derived by extending previous formulations for conventional reinforced concrete beams, just introducing the stresses transferred across the critical shear crack. Since the effects of steel fibers on the others shear resisting mechanisms are not accounted for, “adjusting” empirical factors must be used to fit the experimental results. There is, therefore, the need for developing mechanical models capable to rationally account for the effects of steel fibers on the global shear strength and on each shear resisting mechanisms. In this paper, the previously derived and validated Multi Action Shear Model for RC elements is extended to steel fiber reinforced concrete beams without stirrups. The effects of steel fibers on each resisting mechanism have been identified and incorporated in the formulation of each shear component and in the Multi-Action Shear Model equilibrium equations. The residual tensile stresses of fibrous concrete, obtained through a simple formulation, has been used to: capture the enhancement of the compression chord contribution; the shear transferred by bridging effect of the fibres along the critical shear crack and by dowel action. The proposed model is shown to properly estimate the shear resistance of a large set of available test data, being able to account for most influencing parameters, like fibers types and amounts, concrete strength, longitudinal reinforcement ratios and beam geometry., This work is part of the Research Projects BIA2015-64672-C4-1-R, funded by the Spanish Ministry of Economy and competitiveness, and RTI2018-097314-B-C21, funded by The Spanish Ministry of Science and Innovation., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Safety factor calibration for a new model of shear strength of reinforced concrete building beams and slabs

  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
  • Casas Rius, Joan Ramon|||0000-0003-4473-4308
When assessing existing structures, the availability of adequate safety factors, calibrated with the most accurate models, and for established target reliability indexes, is of critical importance in order to take the right decision regarding the maintenance/repair/strengthening interventions. In the case of shear resistance in reinforced concrete (RC) structures, when using the current design codes provisions for new constructions in assessment results that, in many cases, existing structures may be considered unsafe, implying large economic costs in strengthening or even dismantling. In this research, a proposal of safety factor relative to a recently developed model for shear strength, for elements with and without transversal reinforcement, based on a reliability-based calibration is presented. A formulation is proposed to determine the adequate strength factor for a selected target reliability index of the existing structure and desired remaining service life by means of a safety factor format, considering the load factors present in the Eurocodes. The calibration is carried out considering typical geometry and load ratios of building floors, as well as normal and high strength concrete. The derived safety factor is almost independent of the chosen remaining service life., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Contribution of externally bonded FRP shear reinforcement to the shear strength of RC beams

  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Pujol Sánchez, Mireia|||0000-0002-8674-9033
  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
An experimental program of T-beams strengthened in shear by CFRP sheets has been developed with two longitudinal reinforcement ratios and different externally bonded CFRP shear strengthening amounts in a discontinuous or continuous U-shaped configuration with and without mechanical anchorages. The effectiveness of the external reinforcement without anchorages was low regardless the CFRP reinforcement ratio. There is an evidence of the interaction of the different shear strength components, concrete Vc, transverse steel Vs, CFRP sheets Vf that have been obtained from the registered data of the instrumentation. This interaction might explain that the ultimate shear force of some CFRP-strengthened beams was lower than the one of the control beam. There is a significant difference between the sum of the Vc, Vs, and Vf components and the total shear force. This difference is assumed to be carried out by the flange (including its internal transverse reinforcement), which represents a significant percentage of the total shear strength (with a mean value of 38%). Finally, the contribution of the CFRP has been obtained by different existing guidelines and has been compared to the experimental values., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Embedded fibre reinforced polymer (FRP) reinforcement in concrete structures according to the new version of Eurocode 2, Armadura de polímeros reforzados con fibras (PRF) para estructuras de hormigón en la nueva versión del Eurocódigo 2

  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Torres Llinàs, Lluís
  • de Diego, Ana
The new version of Eurocode 2 will include for the first time an informative annex, Annex R “Embedded FRP reinforcement”, to design reinforced concrete structures with fibre reinforced polymer (FRP) reinforcement. FRP embedded reinforcement has some advantages such as their low susceptibility to corrosion, high-strength, and low life-cycle cost. FRP rebars can be used as longitudinal or transverse reinforcement in a similar way than conventional steel rebars. However, in the design of FRP reinforced concrete structures, some particular aspects related to the reinforcement properties must be taken into account, among which it is worth highlighting their linear elastic behaviour until failure, their relatively low modulus of elasticity or their behaviour under sustained stresses. Since, the content of Annex R is new, a summary and background related to all aspects required for designing with FRP reinforcement are given in this paper., The authors acknowledge the support provided by Spanish Ministry of Science and Innovation (MCIN/  AEI)  and  by  the  European  Funds  for  Regional  Development  in  the  following  projects  during their collaboration in the TN140/SC2 and in the CEN/TC250/SC2/WG1/TG1 (Eva Oller): BIA2015‐64672‐C4‐1‐R, RTI2018‐097314‐B‐C21, and PID2020‐119015GB‐C22., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Performance-based slenderness limits for deformations and reinforcement stresses control in reinforced concrete beams, Límites de esbeltez basados en prestaciones para vigas de hormigón armado para el control de deformaciones y el control de tensiones en la armadura

  • Marí Bernat, Antonio Ricardo|||0000-0002-0994-0715
  • Torres Llinàs, Lluís
  • Oller Ibars, Eva|||0000-0002-0845-3587
  • Barris Peña, Cristina
Los procedimientos actuales de dimensionamiento a flexión de elementos de hormigón armado, basados en la comprobación de estado límite último (ELU), proporcionan suficiente resistencia para soportar las cargas de diseño con un canto reducido. Sin embargo, las dimensiones estrictas de la sección transversal y la cantidad de armadura calculada para satisfacer el ELU pueden ser insuficientes para evitar deformaciones excesivas que pueden producir daños en los elementos no estructurales, o para garantizar el control de la fisuración y satisfacer así, los requisitos de durabilidad, funcionalidad o estética.Debido a la complejidad asociada a un cálculo riguroso de las deformaciones y el ancho de fisura en elementos de hormigón armado a lo largo de su vida útil, una forma efectiva de garantizar la satisfacción del estado límite de servicio es mediante la limitación de la relación de esbeltez l/d del elemento. En el presente estudio, el concepto de esbeltez límite, utilizado anteriormente para el control de la deformación, se generaliza para incorporar las limitaciones de la abertura de fisura, en el marco del diseño estructural basado en prestaciones. Por ello, se derivan las ecuaciones para la esbeltez límite que incorporan los parámetros principales que influyen en el comportamiento de servicio de los elementos de hormigón armado, que son válidos para secciones transversales rectangulares en forma de I o T y para elementos simplemente apoyados o continuos. La fisuración y los efectos a largo plazo se explican a través de coeficientes simplificados derivados de la mecánica estructural y las observaciones experimentales.Las esbelteces límite propuestas, tanto para una carga aplicada constante como para una deformación en la armadura constante, se comparan con las obtenidos utilizando el procedimiento EC2 para el cálculo de deformaciones, basado en la integración de curvaturas. Se han obtenido buenos resultados en términos de errores y dispersión, lo que demuestra que las esbelteces límite propuestas son una herramienta útil para el diseño basado en prestaciones de estructuras de hormigón armado. El carácter mecánico de la formulación facilita su modificación para situaciones diferentes a las utilizadas en su deducción, por ejemplo, diferentes tipos de carga, vigas parcialmente pretensadas o elementos de hormigón armado con FRP, entre otros., The financial support provided by the Spanish Ministry of Economy and Competitiveness (MINECO) and the European Funds for Regional Development (FEDER), through the Research projects: BIA2015-64672-C4-1-R and BIA2017-84975-C2-2-P and through the Excellence network BIA2015-71484-REDT., Peer Reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Influence of the flanges width and thickness on the shear strength of reinforced concrete beams with T-shaped cross section

  • Ayensa, A.
  • Oller, E.
  • Beltrán, B.
  • Ibarz, E.
  • Marí, A.
  • Gracia, L.
Shear design of reinforced concrete beams with T section considers only the contribution of the web, mainly provided by aggregate interlock. However, as the load increases and large web crack openings take place, aggregate interlock reduces and shear stresses tend to concentrate near the neutral axis, usually located in the flanges of T beams, whose contribution to shear strength may be not negligible, as it has been experimentally observed. Thus, the contribution of flanges may drive to considerable cost savings in new structures and may become decisive when evaluating the shear capacity of existing structures. To quantify such contribution, a nonlinear 3D-FEA model has been developed and calibrated with the results of shear tests performed on RC T-beams by the authors. Once adjusted, the model has been used to analyze the shear response of beams with different geometry and longitudinal reinforcement, usual in practice. It has been found that, up to certain limits, the contribution of the flanges to the shear strength increases as the amount of longitudinal reinforcement decreases, as the flanges width increases and as the flange thickness increases. The maximum contribution of flanges found in the present study is 31.3% of the total shear resisted. Furthermore, the numerical model has been used to visualize and quantify aspects that are not easy to obtain experimentally, such as the distribution of the shear stresses between the web and the flanges. The present study will contribute to derive a design expression for the shear effective flanges width of T beams.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Efficiency of shear strengthening of RC beams with externally bonded FRP materials: state-of-the-art in the experimental tests

  • Kotynia, Renata
  • Oller Ibars, Eva
  • Kaszubska, Monika
  • Marí Bernat, Antonio Ricardo
This paper presents a study of the shear capacity of reinforced concrete (RC) beams strengthened in shear with externally bonded (EB) fiber reinforced polymer (FRP) composites, based on the performance of existing published tests. The main objective of this study is to create a comprehensive overview of the performance of different shear strengthening configurations and the failure modes observed in experimental tests. In addition, the influence of the following parameters on the strengthening efficiency has been analyzed: shear span to depth ratio (a/d), existing steel transverse reinforcement ratio (ρsw), concrete strength (fck), size effect (d), longitudinal reinforcement ratio (ρsL), strengthening configurations, type of FRP: sheets or laminates (CFRP, GFRP), and FRP axial stiffness (AfEf)., This paper has been developed under the framework of the Research Projects “BIA2015‐64672‐C4‐1‐R” and “RTI2018‐097314‐BC21” funded by the Spanish Ministry of Economy and Competitiveness (MINECO) and co‐funded by the European Regional Development Funds (ERDF). The authors would also like to thank the Cost Action TU1207 which funded a short term scientific mission of the second author in Lodz University of Technology., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Assessment of the existing models to evaluate the shear strength contribution of externally bonded FRP shear reinforcements

  • Oller Ibars, Eva
  • Kotynia, Renata
  • Marí Bernat, Antonio Ricardo
This paper presents an analysis of the performance of different existing formulations to quantify the FRP contribution to the shear strength of RC elements strengthened in shear by externally bonded FRP sheets. A large database of 555 tests has been assembled distinguishing between the shape of the section, the existence of internal transverse reinforcement and the FRP configurations. In general, predictions are more conservative for beams without transverse reinforcement. In addition, in some cases predictions are unsafe for beams with transverse reinforcement, showing a possible interaction with the internal transverse reinforcement which is not considered in the experimental FRP contribution to the shear strength. For wrapped FRP configurations, models generally assumed failure at the bottom corner of the section and results are very conservative in some cases where failure was experimentally observed along the web. For U-shaped and side-bonded configuration, results depend mainly on the assumed bond model and are more accurate than in the previous case, showing for some models unsafe predictions for the continuous FRP system applied in beams with transverse reinforcement., This paper has been developed under the framework of the Research Projects “BIA2015-64672-575 C4-1-R” and “RTI2018-097314-B-C21” funded by the Spanish Ministry of Economy and Competitiveness (MINECO) and co-funded by the European Regional Development Funds (ERDF). The authors would also like to thank the Cost Action TU1207 which funded a short term scientific mission of the first author in Lodz University of Technology., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Crack detection in concrete elements from RGB pictures using modified line detection kernels

  • Sánchez Calderón, Luis
  • Bairán García, Jesús Miguel
Cracking is inevitable in ordinary reinforced concrete construction, yet it should be controlled to guarantee adequate serviceability and durability. Crack patterns analysis is essential for diagnosis, monitoring and maintenance, to identify malfunctioning or unsafe situations. An important part of this state is the cracking pattern of the elements as an indicator of the tensional distribution in the concrete. A method to search and measure fissures in RGB images of concrete elements has been developed and implemented as a MATLAB script. The algorithm uses several digital image processing tools to detect the measure, the cracks width and orientation; featuring these tools are the spatial filters called “orientation kernels” developed especially for detecting the angle and width of the cracks., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Effects of unidirectional tensile stresses on punching shear strength of RC slabs

  • Fernández Sánchez, Pablo Gonzalo
  • Marí Bernat, Antonio Ricardo
  • Oller Ibars, Eva
  • Domingo Tarancón, Magí
RC slabs can be subjected to transverse loads and in-plane tensile forces simultaneously, as it occurs in top slabs of continuous box girder bridges at intermediate supports, or in floor slabs supported on columns and subjected to horizontal forces, due to skew in-plane compressions. Tensile forces can reduce the punching capacity of the slabs, aspect not studied yet. An experi-mental, numerical and theoretical investigation has been carried out, in which 5 1.65x1.65x0.12 m slabs have been tested under a point load and different degrees of unidirectional tensile force. Numerical predictions were made with FEA software ABAQUS and, from the theoretical point of view, the Compression Chord Capacity Model (CCCM) was extended to take into account the effect of in-plane tensile forces in the punching strength of the slabs. The experimental results showed that the ultimate punching load decreases linearly with the applied tensile force, and if that tensile force cracks the slabs, such reduction is higher. Results obtained with FEA and CCCM are in agreement with the observations made at the laboratory, This work has been carried out within the framework of research project BIA-2015-64672-C4-1-R, financed by the Ministry of Economy and Competitiveness (MINECO) of Spain. The authors want o deeply thank the personnel of the Structural Technology Laboratory of the Polytechnic University of Catalonia and Master student Laura Beltrán who collaborated in the execution of the tests., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Contribution of externally bonded FRP shear reinforcement to the shear strength of RC beams

  • Oller Ibars, Eva
  • Pujol Sánchez, Mireia
  • Marí Bernat, Antonio Ricardo
An experimental program of T-beams strengthened in shear by CFRP sheets has been developed with two longitudinal reinforcement ratios and different externally bonded CFRP shear strengthening amounts in a discontinuous or continuous U-shaped configuration with and without mechanical anchorages. The effectiveness of the external reinforcement without anchorages was low regardless the CFRP reinforcement ratio. There is an evidence of the interaction of the different shear strength components, concrete Vc, transverse steel Vs, CFRP sheets Vf that have been obtained from the registered data of the instrumentation. This interaction might explain that the ultimate shear force of some CFRP-strengthened beams was lower than the one of the control beam. There is a significant difference between the sum of the Vc, Vs, and Vf components and the total shear force. This difference is assumed to be carried out by the flange (including its internal transverse reinforcement), which represents a significant percentage of the total shear strength (with a mean value of 38%). Finally, the contribution of the CFRP has been obtained by different existing guidelines and has been compared to the experimental values., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Shear strength of non-slender reinforced concrete beams

  • Bairán García, Jesús Miguel
  • Menduiña Montero, Raul
  • Marí Bernat, Antonio Ricardo
  • Cladera Bohigas, Antoni
Shear strength of non-slender reinforced concrete beams, in which a/d¿ 2.5, is enhanced due to arching action. Current shear design methods for such elements, including the Strut-and-Tie Method (STM), show deviations with respect to tests results. In this paper, a shear strength mechanical model developed for slender beams is extended to non-slender beams. The effects of the non-planar strains distribution, of the multi-compression stress state generated near the applied load, and those of the pre-determined position and inclination of the critical shear crack are incorporated in the model formulation. The predictions of the proposed model have been compared with those obtained using the STM following the ACI and FIP recommendations and the EC2 simplified proposal. Three previously published databases, including the results of 486 shear tests of non-slender beams with and without web reinforcement, have been considered. The predictions by the proposed model resulted in better precision and less scatter, for all subset of tests, while the proposed method is direct and simpler for daily engineering purposes., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Simplified tests to study the size effect of the compression chord in beams under shear forces: application of DIC methodology, Ensayos en probetas para el estudio del efecto tamaño en la cabeza de compresión de vigas sometidas a esfuerzo cortante: aplicación de la metodología DIC

  • Oller Ibars, Eva
  • Barris Peña, Cristina
  • Marí Bernat, Antonio Ricardo
  • Torres Llinàs, Lluís
  • Santander, Andres
To evaluate how the size effect affects the stresses developed along the compression chord in a beams subjected to shear forces, a simplified experimental program was developed on 50 prismatic specimens subjected to a splitting test. The studied parameters were: dimensions, slenderness, concrete compressive strength, and maximum aggregate size. To capture the post-peak behavior of the concrete, the load was introduced as a function of the crack width, through appropriate control algorithms. Digital Image Correlation (DIC) in a 2D configuration has also been used to accurately capture the formation, width and propagation of cracks to corroborate the experimental measurements., The financial support provided by the Spanish Ministry of Economy and Competitiveness (MINECO) and the European Funds for Regional Development (FEDER), through the Research projects: BIA2015-64672-C4-1-R and BIA2017-84975-C2-2-P and through the Excellence network BIA2015-71484-REDT., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Performance-based slenderness limits for deflections and reinforcement stresses control in RC beams, Límites de esbeltez basados en prestaciones para vigas de hormigón armado para el control de deformaciones y el control de tensiones en la armadura

  • Marí Bernat, Antonio Ricardo
  • Torres Llinàs, Lluís
  • Oller Ibars, Eva
  • Barris Peña, Cristina
Due to the complex deformational behavior of cracked RC members, an effective way to ensure the fulfilment of the SLS is to limit the slenderness ratio l/d of the element. In this study, the deformation slenderness limit concept is generalized to incorporate crack width limitations. The proposed slenderness limits are compared with those derived from non-linear time-dependent analysis and also with those obtained using the EC2 method of deflections interpolation. Very good approximation and low scatter has been obtained showing that the proposed slenderness limits are a useful tool for performance-based design of RC structures., The financial support provided by the Spanish Ministry of Economy and Competitiveness (MINECO) and the European Funds for Regional Development (FEDER), through the Research projects: BIA2015-64672-C4-1-R and BIA2017-84975-C2-2-P and through the Excellence network BIA2015-71484-REDT, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Effects of tensile stresses on punching shear strength of RC slabs

  • Fernández Sánchez, Pablo Gonzalo
  • Marí Bernat, Antonio Ricardo
  • Oller Ibars, Eva
  • Domingo Tarancón, Magí
RC slabs can be subjected to transverse loads and tensile in-plane forces, as it occurs in top slabs of continuous bridges under negative moments. Tensile forces can reduce the shear or punching capacity of the slab, aspect not yet studied. A theoretical and experimental investigation has been carried out, in which 10 slabs have been tested under a point load and different degrees of tensile force. The results of five axisymmetrically supported slabs of 1.65x1.65x0.12m are presented. Numerical predictions were made with FEA software ABAQUS and, in addition, the Compression Chord Capacity Mechanical Model CCCM, was extended to account for the effect of in-plane tensile forces. The experimental results showed that the ultimate punching load diminished linearly with the applied tensile force applied and that, after yielding of longitudinal reinforcement such reduction was higher., Los autores desean agradecer la financiación recibida del Ministerio de Ciencia e Innovación y de los Fondos Europeos de Desarrollo Regional (FEDER) a través del proyecto “Evaluación de la capacidad resistente frente a esfuerzos tangentes de estructuras de hormigón mediante modelos mecánicos para la extensión de su vida útil” BIA2015-64672-C4-1-R . Así mismo desean agradecer el apoyo del Laboratorio de Tecnologia de Estructuras y Materiales de la UPC y de todos los técnicos que han contribuido a la realización de esta campaña experimental y sin cuya ayuda no habría sido posible., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Theoretical prediction of the punching shear strength of concrete flat slabs under in-plane tensile forces

  • Fernández Sánchez, Pablo Gonzalo
  • Marí Bernat, Antonio Ricardo
  • Oller Ibars, Eva
RC slabs can be subjected simultaneously to transverse loads and in-plane tensile forces, as it happens in top slabs of continuous box girder bridges decks, in the regions of negative moments, or in flat slabs subjected to horizontal loads, produced by wind or earth pressure. Tensile forces can reduce the shear punching capacity of slabs. However, few studies have been carried out to quantify this effect. With this purpose, a mechanical model has been developed to capture the influence of in-plane tensile forces on the punching shear strength and verified with punching tests under different in-plane tensile load levels. The model, presented in this paper, consists of an extension of the Punching shear Compression Chord Capacity Model to account for the effects of tensile forces on the resisting actions. A linear reduction of the punching shear strength as a function of the external load applied has been obtained for moderate tensile forces, whereas high level of tensile forces may produce premature yielding of the reinforcement and further reduction of the punching shear strength. The proposed model accurately captures the available test results, including the effects of the premature yielding of reinforcement when the tensile force produces concrete cracking. In addition, predictions of punching-shear-tensile tests available in the literature were made with different theoretical models included in design codes, which yielded in general conservative results and showed high scatter., This work was developed in the framework of Research Project BIA-2015-64672-C4-1-R, financed by the Ministry of Economy and Competitiveness (MINECO) of Spain and the European Funds for Regional Development (FEDER). The authors want to thank Mr. José Romo, from FHECOR Engineering, for transmitting his experience in bridge design that helped to set the problem and to the director and technicians of the Structural Technology Laboratory of UPC, for their help in carrying out the experimental campaign., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Ensayos a cortante y punzonamiento sobre un puente antiguo de hormigón armado sobre el rio Anoia en Gelida, Punching and shear tests on an old reinforced concrete bridge over the Anoia river in Gelida

  • Marí Bernat, Antonio Ricardo
  • Fernández Sánchez, Pablo Gonzalo
  • Oller Ibars, Eva
  • Aceña Ramos, Valentín
  • García Vicente, Tomàs
  • Duarte Gómez, Noemí
Se presentan los estudios llevados a cabo sobre el tablero de un puente de hormigón armado, construido en 1929 en Gelida (Barcelona) sobre el río Anoia, formado por 11 vanos isostáticos de 10,5 m de luz, con vigas sección en ¿, armadas con barras lisas levantadas y cercos. Se han realizado ensayos de cortante sobre vigas en T y de punzonamiento en la losa superior, así como predicciones teóricas de los resultados experimentales. La estructura ha mostrado gran resistencia frente a solicitaciones tangentes y gran rigidez, pese a la heterogeneidad del hormigón, del uso de barras lisas y de la presencia de corrosión local, satisfaciendo los requisitos de seguridad y aptitud al servicio establecidos en las normativas actuales., Este trabajo se ha desarrollado en el contexto del proyecto BIA2015-64672-C4-1-R, financiado por el Ministerio de Economía y Competitividad de España. La Diputación de Barcelona, ha facilitado las vigas ensayadas, así como su corte, manipulación en obra y transporte al laboratorio. El equipo de la UPC agradece enormemente la colaboración de la ingeniera de la Diputación de Barcelona, Maria Josep Palau, de los ingenieros de la empresa constructora Pasquina y de la Dirección de Obra, Sergi Font y José Escudero, entre otros, por su inmensa ayuda, así como a los técnicos del Laboratorio de Tecnología de Estructuras y Materiales de la UPC, Carlos Hurtado, Jordi Cabrerizo y Robert McAloon, por su dedicación y entrega. Finalmente, se agradece a los estudiantes Felipe Baba, Alberto Sarmiento y Raúl Salinas quienes han desarrollado su tesis de Máster en el contexto de este proyecto., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Influence of the flanges width and thickness on the shear strength of reinforced concrete beams with T-shaped cross section

  • Ayensa Pardo, Alberto
  • Oller Ibars, Eva
  • Beltrán, Beatriz
  • Ibarz Montaner, Elena
  • Marí Bernat, Antonio Ricardo
  • Gracia Villa, Luis
Shear design of reinforced concrete beams with T section considers only the contribution of the web, mainly provided by aggregate interlock. However, as the load increases and large web crack openings take place, aggregate interlock reduces and shear stresses tend to concentrate near the neutral axis, usually located in the flanges of T beams, whose contribution to shear strength may be not negligible, as it has been experimentally observed. Thus, the contribution of flanges may drive to considerable cost savings in new structures and may become decisive when evaluating the shear capacity of existing structures. To quantify such contribution, a nonlinear 3D-FEA model has been developed and calibrated with the results of shear tests performed on RC T-beams by the authors. Once adjusted, the model has been used to analyze the shear response of beams with different geometry and longitudinal reinforcement, usual in practice. It has been found that, up to certain limits, the contribution of the flanges to the shear strength increases as the amount of longitudinal reinforcement decreases, as the flanges width increases and as the flange thickness increases. The maximum contribution of flanges found in the present study is 31.3% of the total shear resisted. Furthermore, the numerical model has been used to visualize and quantify aspects that are not easy to obtain experimentally, such as the distribution of the shear stresses between the web and the flanges. The present study will contribute to derive a design expression for the shear effective flanges width of T beams., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Analysis of shear resisting actions by means of optimization of strut and tie models taking into account crack patterns

  • Bairán García, Jesús Miguel
  • Marí Bernat, Antonio Ricardo
  • Cladera Bohigas, Antoni
The shear resisting actions in reinforced concrete elements without transverse reinforcement is analyzed by means of optimized strut-and-tie models with concrete ties. Biaxial failure criteria are used for uncracked and cracked regions. The stress transfer capacity across cracks is accounted for by including the inclination between the stress field and the crack opening and sliding. An experimental case-study is analyzed. It is shown that that different shear resisting actions can occur in different regions of the beam. The strut-and-tie scheme in the critical region is consistent with the Multi-Action Shear Strength Model (MASM). Analysis of shear resisting actions by means of optimization of strut and tie models taking into account crack patterns., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Application of the Compression Chord Capacity Model to predict the fatigue shear strength of reinforced concrete members without stirrups

  • Cladera Bohigas, Antoni
  • Ribas González, Carlos Rodrigo
  • Oller Ibars, Eva
  • Marí Bernat, Antonio Ricardo
The Compression Chord Capacity Model (CCCM), previously developed by the authors with other colleagues, is a simplified model for the shear strength prediction of reinforced and prestressed concrete members with and without transverse reinforcement, with I, T or rectangular cross-section, which represents a useful tool for structural design and assessment in engineering practice. The principal advantage of the application of a mechanical model is the possibility to extend it to different cases, without the need of empirical calibrations. According to the CCCM, the shear strength depends on the concrete tensile strength. In this communication, the CCCM is extended to assess the fatigue shear strength of RC members just incorporating the equation proposed in Model Code 2010 for the concrete tensile fatigue strength. A good performance of the model was observed when analysing the ratio Vtest/Vpred through a previously published database, showing a low scatter (COV 14.7 %)., Esta investigación se ha desarrollado en el marco de dos proyectos cofinanciados por la Agencia Estatal de Investigación y Fondos FEDER: BIA2015-64672-C4-3-R y BIA2015-64672-C4-1-R., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Shear fatigue strength of reinforced concrete members without transverse reinforcement according to the compression chord capacity model

  • Cladera Bohigas, Antoni
  • Ribas González, Carlos Rodrigo
  • Oller Ibars, Eva
  • Marí Bernat, Antonio Ricardo
Although the shear fatigue behaviour of elements without shear reinforcement has been studied for a while, there is still a need for a simple mechanical model that evaluates the shear fatigue strength. The Compression Chord Capacity Model (CCCM), previously developed by the authors, is a simplified model for the shear strength prediction of reinforced and prestressed concrete members with and without transverse reinforcement, with I, T or rectangular cross-sections. This model represents a useful tool for structural design and assessment in engineering practice. In this paper, the CCCM has been extended to assess the fatigue shear strength of RC elements. This extension is consistent since the existing observed fatigue failure modes show similarities with the initial assumption of the model, which considers that the member shear strength is controlled by the shear capacity of the flexural compression chord. Three different approaches to take into account the influence of the fatigue have been combined with the CCCM. In general, a good performance of the model combined with the three different approaches was observed when analysing the ratio Vtest/Vpred through a database of 87 tests previously published by other authors, showing a low scatter (<15%) and a significant safety given by the minimum ratio and the 5th percentile., The authors want to acknowledge the financial support provided by the Spanish Ministry of Economy and Competitiveness (MINECO) and the European Funds for Regional Development (FEDER), through research projects: BIA2015-64672-C4-3-R and BIA2015-64672-C4-1-R. The authors also want to thank to Dr. Miguel Fernández-Ruiz for providing the authors the fatigue shear tests database., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Experimental investigation of the shear strength of one-way reinforced concrete (RC) slabs subjected to concentrated loads and in-plane transverse axial tension

  • Fernández Sánchez, Pablo Gonzalo
  • Marí Bernat, Antonio Ricardo
  • Oller Ibars, Eva
This paper presents the results of an experimental campaign carried out to investigate the effects of in-plane transverse tensile forces on the shear strength of linearly supported one-way reinforced concrete (RC) slabs without shear reinforcement subjected to concentrated loads. A total of 5 half scale slabs (1650¿×¿1650¿×¿120¿mm), subjected simultaneously to different levels of in-plane tensile forces and a concentrated load were tested up to failure. The clear shear span to effective depth ratio av/d was equal to 3 in all tests, to minimize the effects of the direct transmission of the load to the closest support, the so called arching action. As observed, the shear strength barely decreases with increasing values of the tensile force applied, even for values of the external force that cracked the concrete cross-section of the slabs in the direction perpendicular to the span. These observations may indicate that the shear–flexural behavior in the spanning direction is not significantly affected by the membrane forces in the transverse direction., This work has been carried out within the framework of the research project BIA-2015-64672-C4-1-R, financed by the Ministry of Economy and Competitiveness (MINECO) of Spain, and with the invaluable help of the technicians and the director of the Laboratory of Technology of Structures and Materials of the Universitat Politècnica de Catalunya. The authors want also to thank Master students Pau Figueras and Laura Beltran who collaborated in the numerical predictions and execution of the tests, respectively., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Theoretical prediction of the shear strength of reinforced concrete slabs under concentrated loads close to linear supports

  • Fernández Sánchez, Pablo Gonzalo
  • Marí Bernat, Antonio Ricardo
  • Oller Ibars, Eva
A mechanical model has been developed by the authors in order to predict the shear strength of reinforced concrete slabs under concentrated loads close to linear supports. Such situation takes place very often in bridge slabs and cantilever sections of bridge decks under concentrated heavy vehicle loads. The model takes into account a significant number of variables involved in the phenomenon, such as the clear shear span, the concrete compressive strength, the reinforcement ratio, the effective depth, the load spreading angle, the size effect and the size of the loaded area. It is applicable to simply supported slabs, cantilever slabs and situations with partial restraint to the rotation, such as intermediate supports. It has been validated with a database of 90 shear test in slabs subjected to a single concentrated load in different supporting conditions, yielding results on the safe side and showing low scatter. A parametric analysis of the model is also presented, detailing how the different involved variables affect the shear strength. These results, along with the simplified expressions developed for the shear strength calculation, provide a useful tool for the assessment of the shear strength of RC solid slabs in daily engineering., This work was developed in the framework of Research Project BIA-2015-64672-C4-1-R, financed by the Ministry of Economy and Competitiveness (MINECO) of Spain and the European Funds for Regional Development (FEDER). The authors want to thank Ph.D candidate Alex Micael Dantas de Sousa, from the University of Sao Paulo, and Prof Eva Lantsoght from Tecnische Universiteit of Delft, for sharing the up-to-date database of shear test on RC slabs, which has facilitated the development and validation of the proposed mechanical model., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Performance-based slenderness limits for deformations and reinforcement stresses control in reinforced concrete beams, Límites de esbeltez basados en prestaciones para vigas de hormigón armado para el control de deformaciones y el control de tensiones en la armadura

  • Marí Bernat, Antonio Ricardo
  • Torres Llinàs, Lluís
  • Oller Ibars, Eva
  • Barris Peña, Cristina
Los procedimientos actuales de dimensionamiento a flexión de elementos de hormigón armado, basados en la comprobación de estado límite último (ELU), proporcionan suficiente resistencia para soportar las cargas de diseño con un canto reducido. Sin embargo, las dimensiones estrictas de la sección transversal y la cantidad de armadura calculada para satisfacer el ELU pueden ser insuficientes para evitar deformaciones excesivas que pueden producir daños en los elementos no estructurales, o para garantizar el control de la fisuración y satisfacer así, los requisitos de durabilidad, funcionalidad o estética.Debido a la complejidad asociada a un cálculo riguroso de las deformaciones y el ancho de fisura en elementos de hormigón armado a lo largo de su vida útil, una forma efectiva de garantizar la satisfacción del estado límite de servicio es mediante la limitación de la relación de esbeltez l/d del elemento. En el presente estudio, el concepto de esbeltez límite, utilizado anteriormente para el control de la deformación, se generaliza para incorporar las limitaciones de la abertura de fisura, en el marco del diseño estructural basado en prestaciones. Por ello, se derivan las ecuaciones para la esbeltez límite que incorporan los parámetros principales que influyen en el comportamiento de servicio de los elementos de hormigón armado, que son válidos para secciones transversales rectangulares en forma de I o T y para elementos simplemente apoyados o continuos. La fisuración y los efectos a largo plazo se explican a través de coeficientes simplificados derivados de la mecánica estructural y las observaciones experimentales.Las esbelteces límite propuestas, tanto para una carga aplicada constante como para una deformación en la armadura constante, se comparan con las obtenidos utilizando el procedimiento EC2 para el cálculo de deformaciones, basado en la integración de curvaturas. Se han obtenido buenos resultados en términos de errores y dispersión, lo que demuestra que las esbelteces límite propuestas son una herramienta útil para el diseño basado en prestaciones de estructuras de hormigón armado. El carácter mecánico de la formulación facilita su modificación para situaciones diferentes a las utilizadas en su deducción, por ejemplo, diferentes tipos de carga, vigas parcialmente pretensadas o elementos de hormigón armado con FRP, entre otros., The financial support provided by the Spanish Ministry of Economy and Competitiveness (MINECO) and the European Funds for Regional Development (FEDER), through the Research projects: BIA2015-64672-C4-1-R and BIA2017-84975-C2-2-P and through the Excellence network BIA2015-71484-REDT., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Evaluación del tiempo de recuperación de edificios de concreto reforzado dañados por sismo

  • Gutiérrez, Juan Jesús
  • Ayala, A. Gustavo
  • Bairán García, Jesús Miguel
Sismos recientes han demostrado la importancia de evaluar el tiempo que tardarían los edificios dañados en ser reparados, ocupables y funcionales nuevamente, debido a que el tiempo de inactividad puede generar pérdidas económicas e implicaciones sociales importantes. En este trabajo se presenta una metodología para evaluar el tiempo de recuperación en términos probabilistas de edificios que han sido dañados por sismo. El esquema de evaluación propuesto se basa en el método PERT y es consistente con el esquema de evaluación sísmica propuesto por el PEER y con el concepto de resiliencia desarrollado por el MCEER. Se presenta la evaluación de un edificio de concreto reforzado en el que se incluyen los muros de mampostería no reforzada. Recent earthquakes have demonstrated the importance of assessing the time it would take for damaged buildings to be repaired, occupied and functional again, because downtime can lead to significant economic losses and social implications. This paper presents a methodology to evaluate the recovery time in probabilistic terms of buildings that have been damaged by earthquakes. The proposed evaluation scheme is based on the PERT method and is consistent with the seismic evaluation scheme proposed by PEER and with the concept of resilience developed by the MCEER. The evaluation of a reinforced concrete building is presented, in which the infill unreinforced masonry walls are included., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

A punching shear mechanical model for reinforced concrete flat slabs with and without shear reinforcement

  • Marí Bernat, Antonio Ricardo
  • Cladera Bohigas, Antoni
  • Oller Ibars, Eva
  • Bairán García, Jesús Miguel
A punching shear strength mechanical model for RC flat slabs with and without shear reinforcement, based on a beam shear model previously developed by the authors, is presented. The differences in resisting actions between beam shear and punching shear have been identified and incorporated into the governing equations and failure modes, resulting in simple but accurate punching design equations. The model consistently explains and quantifies some experimentally observed phenomena, such as the higher contribution of the concrete to the punching shear strength of slabs than in the case of beams subjected to shear, mainly due to the multi-axial state of stresses that takes place near the support. Furthermore, the model provides physical meaning to some parameters used in the design, such as the position of the critical perimeter or the effective stress of the punching reinforcement, among others. Very good agreement has been obtained between the model predictions and the results of 560 punching tests of concentrically loaded slabs, with and without shear reinforcement, included in two available large databases. The mechanical character of the model allows its extension to post-tensioned flat slabs, border or corner columns, steel fiber and FRP reinforced concrete slabs or different strengthening systems in a consistent way., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication

SP-357—8: Punching-shear strength of reinforced concrete slabs subjected to concentric transverse loads and in-plane tensile forces

  • Marí Bernat, Antonio Ricardo
  • Fernández Sánchez, Pablo Gonzalo
  • Oller Ibars, Eva
  • Cladera Bohigas, Antoni
Reinforced concrete slabs can be subjected simultaneously to transverse loads and in-plane tensile forces, as it occurs in top slabs of continuous box girder bridges at intermediate supports, or in flat slabs supported on columns, subjected to horizontal loads. To study the effects of in-plane forces in the slab punching-shear strength, an experimental and theoretical investigation was carried out, which is described in this paper. Five square slabs of 1650 mm (42”) side and 120 mm (4.7”) thickness were tested under a centered transverse point load and different degrees of uniaxial in-plane tensile force. Numerical predictions using non-linear finite element analyses were performed to help in the experiments design. Furthermore, the punching-shear mechanical model, Compression Chord Capacity Model (CCCM), was extended to incorporate the effects of in-plane tensile forces. The experimental results showed that the punching strength linearly decreases with the level of applied tensile force and, if cracking in the slabs is produced by the tensile force, yielding of the reinforcement and further reduction may take place. Excellent agreement was found between theoretical predictions and tests results. Furthermore, the CCCM was verified with available results of punching tests with uniaxial and biaxial tensile forces, obtaining very good results., This work has been carried out within the framework of research projects BIA-2015-64672-C4-1-R, and BIA2015- 64672-C4-3-R financed by the Ministry of Economy and Competitiveness (MINECO) of Spain, and also with the financial support of the Government of Catalonia through the contract for research and innovation in infrastructures E1-INF-18500. The authors want to deeply thank also the personnel of the Structural Technology Laboratory of the Universitat Politècnica de Catalunya., Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Strengthening of existing concrete structures with fibre reinforced polymers (FRP) in the new version of Eurocode 2, Refuerzo de estructuras existentes de hormigón con polímeros reforzados con fibras (PRF) en la nueva versión del Eurocódigo 2

  • Oller Ibars, Eva
  • de Diego, Ana
  • Torres Llinàs, Lluís
  • Madera, Pedro
This  paper  aims  to  introduce  the  content  of  Annex  J  “Strengthening  of  Existing  Concrete  Structures with CFRP” of Eurocode 2 [1]. This is first time that the design of adhesively bonded reinforcement  with  CFRP  has  been  introduced  in  the  European  regulations  through  an  informative annex. Annex J considers two different bonded strengthening techniques: externally bonded reinforcement (EBR) that consists of bonding CFRP strips or sheets to the surface of concrete elements, and near surface mounted reinforcement (NSM) that consists of embedded CFRP strips or rods to the slot cut in the concrete cover. Since, the content of Annex J is new, a summary  and  background  related  to  all  aspects  required  for  designing  CFRP  strengthened  systems for concrete structures, are given in this paper., The authors acknowledge the support provided by Spanish Ministry of Science and Innovation (MCIN/AEI) and by the European Funds for Regional Development in the following projects during their collaboration in the CTN140/SC2 and in the CEN/TC250/SC2/WG1/TG1 (Eva Oller): BIA2015‐64672‐C4‐1‐R, RTI2018‐097314‐B‐C21, and PID2020‐119015GB‐C22., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

A new concrete plastic-damage model with an evolutive dilatancy parameter

  • Poliotti, Mauro
  • Bairán García, Jesús Miguel
Typical plastic-damage models for concrete use a constant dilatancy parameter. On problems sensitive to confinement and shear softening, this parameter needs ad hoc calibration to fit experimental observations. This makes the model not objective for general applications. To overcome this issue, in this paper, a constitutive plastic-damage model with evolutive dilatancy is proposed for concrete. The evolution of dilatancy is made dependent on the plastic-damage and stress states. The proposed evolution law is validated by comparison of numerical simulations with available experimental results. The validation includes: concrete specimens under uniaxial compression measuring the free expansion, passively confined concrete specimens with different confining materials, and reinforced concrete panels under in-plane shear. It is concluded that the model accurately reproduces concrete lateral expansion through different nonlinear states. Proper modeling of concrete nonlinear expansion proves essential for capturing the response in a number of situations: softening under high shear stresses, confinement, and ductility assessment., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Mechanical model for the shear strength of steel fiber reinforced concrete (SFRC) beams without stirrups

  • Marí Bernat, Antonio Ricardo
  • Spinella, Nino
  • Recupero, Antonino
  • Cladera Bohigas, Antoni
The final publication is available at Springer via http://dx.doi.org/10.1617/s11527-020-01461-4., Numerous studies have shown that adding steel fibers to the concrete mixture improves both the shear strength and ductility of reinforced concrete beams. Most current shear design formulations for steel fiber reinforced concrete beams are empirically based and their predictions provide acceptable results when compared with tests results, but only in limited ranges of the parameters involved. On the other hand, many shear theoretical models suggested in the literature are derived by extending previous formulations for conventional reinforced concrete beams, just introducing the stresses transferred across the critical shear crack. Since the effects of steel fibers on the others shear resisting mechanisms are not accounted for, “adjusting” empirical factors must be used to fit the experimental results. There is, therefore, the need for developing mechanical models capable to rationally account for the effects of steel fibers on the global shear strength and on each shear resisting mechanisms. In this paper, the previously derived and validated Multi Action Shear Model for RC elements is extended to steel fiber reinforced concrete beams without stirrups. The effects of steel fibers on each resisting mechanism have been identified and incorporated in the formulation of each shear component and in the Multi-Action Shear Model equilibrium equations. The residual tensile stresses of fibrous concrete, obtained through a simple formulation, has been used to: capture the enhancement of the compression chord contribution; the shear transferred by bridging effect of the fibres along the critical shear crack and by dowel action. The proposed model is shown to properly estimate the shear resistance of a large set of available test data, being able to account for most influencing parameters, like fibers types and amounts, concrete strength, longitudinal reinforcement ratios and beam geometry., This work is part of the Research Projects BIA2015-64672-C4-1-R, funded by the Spanish Ministry of Economy and competitiveness, and RTI2018-097314-B-C21, funded by The Spanish Ministry of Science and Innovation., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Detección y medición semiautomática de fisuras en elementos de hormigón en fotos digitales usando procesamiento de imágenes

  • Sánchez Claderón, Luis
  • Bairán García, Jesús Miguel
La fisuración es inevitable en las obras de hormigón armado, pero debe de ser controlada para asegurar un adecuado comportamiento en servicio y por durabilidad. El análisis de los patrones de fisuración es una parte esencial en el diagnóstico, monitorización y mantenimiento; para identificar deficiencias o situaciones comprometidas. Por otro lado, el patrón de fisuración también puede ser un indicador de la distribución tensional del hormigón y de los esfuerzos determinantes en una zona. En este artículo se presente un nuevo método para la búsqueda y medición de fisuras en imágenes en color de elementos de hormigón. El algoritmo usa diversas herramientas de procesamiento digital de imágenes para medir la orientación de las fisuras y entre estas herramientas destaca un tipo especial de filtros llamados “orientation kernels” desarrollados especialmente para detectar el ángulo y ancho de las fisuras., Esta investigación es parcialmente apoyada por los proyectos BIA2012-36848 “Performance-based design of partially prestressed concrete structures ”, y BIA2015-64672-C4-1-R “Contribution to the extension of service lifetime of existing concrete structures through an adequate structural evaluatio n and strengthening with advanced materials” , financiados a su vez por el Ministerio Economía, 14/14 Industria y Competitividad de España y por los Fond os Europos de Desarrollo Regional (FEDER). También se debe mencionar el financiamiento por par te de la Secretaria de Educación Superior, Ciencia, Tecnología y Educación (SENECYCT) (insituc ión del gobierno ecuatoriano) a través de una beca de “Convocatoria Abierta” para programas d e Masters y Phd., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Performance-based slenderness limits for deformations and crack control of reinforced concrete flexural members

  • Marí Bernat, Antonio Ricardo
  • Torres Llinàs, Lluís
  • Oller Ibars, Eva
  • Barris Peña, Cristina
The use of high strength materials allows flexural members to resist the design loads or to cover long spans with a reduced depth. However, the strict cross section dimensions and reinforcement amount required in ULS are often insufficient to satisfy the serviceability limit states. Due to the complexity associated to a rigorous computation of deflections and cracks width in cracked RC members along their service life, an effective way to ensure the satisfaction of the SLS is to limit the slenderness ratio l/d of the element. In the present study, the slenderness limit concept, previously used for deflection control, is generalized to incorporate the crack width limitations in the framework of structural performance-based design. Equations for slenderness limits incorporating the main parameters influencing the service behaviour of RC members are derived. Cracking and long-term effects are accounted for through simplified coefficients derived from structural concrete mechanics and experimental observations. The proposed slenderness limits are compared with those derived from a numerical non-linear time-dependent analysis for two case studies, and also with those obtained using the EC2 procedure for deflection calculation in terms of constant applied load and constant reinforcement strain. Very good results have been obtained in terms of low errors and scatter, showing that the proposed slenderness limits are a useful tool for performance-based design of RC structures., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Mechanical model for the shear strength of steel fibers reinforced concrete beams (SFRC) without stirrups, Modelo mecánico para la resistencia a cortante de vigas de hormigón armado reforzado con fibras, sin armadura de cortante

  • Marí Bernat, Antonio Ricardo
  • Spinella, Nino
  • Recupero, Antonino
  • Cladera Bohigas, Antoni
Despite the numerous studies made showing that the addition of steel fibres to concrete enhances the shear strength of RC beams, current design formulations are still empirical and present large scatter in front of the test results. In this paper, the previously developed Multi-Action Shear Model is extended to SFRC beams without stirrups, adopting an analytical formulation to evaluate the residual tensile stress of SFRC and incorporating the effects of the crack bridging capacity of SFRC in the shear resisted trough the different shear-transfer mechanisms. The proposed model predicts the tests results included in a recently published database with 448 shear tests with less scatter than any of the existing models., The financial support provided by the University of Messina (Italy), through the scholarship granted for a two-months research and teaching stage of the first author, is acknowledged. This work is part of the Research Projects BIA2015-64672-C4-1-R, funded by the Spanish Ministry of Economy and competitiveness, and RTI2018-097314-B-C21, funded by the Spanish Ministry of Science and Innovation., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

A variable order framework for 3D nonlinear analysis of reinforced concrete frames under general loading

  • Poliotti, Mauro
  • Bairán García, Jesús Miguel
  • Moller, O.
A framework for the analysis of three-dimensional reinforced concrete frame structures, capable of reproducing general failure modes, is presented. A force-based model which guarantees the equilibrium between nodal and sectional forces is enhanced by means of a cross-sectional model. It is capable of capturing the complex coupling between all the internal forces. Consequently, different failure modes can be reproduced such as shear, torsional, flexural or axial failures. Material modeling of concrete is made using a plastic-damage model that incorporates a variable dilatancy parameter. The sectional and constitutive models are implemented in OpenSees. The sectional model can be used at each integration point of the force-based element. Alternatively, it can be used only where high coupling between the internal forces is expected, producing a variable order structural model. The validation shows that the frame element is capable of accurately reproduce beams and columns under monotonic and cyclic loads. The framework presented is a powerful numerical instrument for the analysis, design and assessment of reinforced concrete buildings and bridges., The first and second authors acknowledge the support provided by Spanish Ministry of Economy, Industry and Competitiveness and the European Regional Development Fund (ERDF), through the projects BIA2015-64672-C4-1R, BIA2012-36848 and RTI2018-097314-B-C21. The first author acknowledges the support of the Catalan Agency for University and Research through doctoral scholarship 2018FI-B1-00103. The third author acknowledges the support of the Research Council of Universidad Nacional de Rosario (CIUNR) and the Science and Technology Secretariat (SECyT), through the project 1ING601., Peer Reviewed, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura::9.1 - Desenvolupar infraestructures fiables, sostenibles, resilients i de qualitat, incloent infraestructures regionals i transfrontereres, per tal de donar suport al desenvolupament econòmic i al benestar humà, amb especial atenció a l’accés assequible i equitatiu per a totes les persones, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura::9.a - Facilitar el desenvolupament d’infraestructures sostenibles i resilients als països en desenvolupament per mitjà de més suport financer, tecnològic i tècnic als països africans, països menys avançats, països en desenvolu­pament sense litoral i petits estats insulars en desenvolupament, Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles, Objectius de Desenvolupament Sostenible::13 - Acció per al Clima::13.1 - Enfortir la resiliència i la capacitat d’adaptació als riscos relacionats amb el clima i els desastres naturals a tots els països, Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura, Objectius de Desenvolupament Sostenible::13 - Acció per al Clima, Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles::11.b - Per a 2020, augmentar substancialment el nombre de ciutats i assentaments humans que adopten i posen en marxa polítiques i plans integrats per promoure la inclusió, l’ús eficient dels recursos, la mitigació del canvi climàtic i l’adaptació a aquest, així com la resiliència davant dels desastres, i desenvolupar i posar en pràctica una gestió integral dels riscos de desastre a tots els nivells, d’acord amb el Marc de Sendai per a la reducció del risc de desastres 2015.2030, Objectius de Desenvolupament Sostenible::11 - Ciutats i Comunitats Sostenibles::11.5 - Per a 2030, reduir de forma significativa el nombre de morts causades per desastres, inclosos els relacio­nats amb l’aigua, i de persones afectades per aquests, i reduir substancialment les pèrdues econòmiques directes causades per desastres relacionades amb el producte interior brut mundial, fent un èmfasi especial en la protecció de les persones pobres i de les persones en situacions de vulnerabilitat, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Ultimate capacity of corroded statically indeterminate reinforced concrete members

  • Fernández Pérez, Ignacio
  • Herrador Barrios, Manuel F.
  • Marí Bernat, Antonio Ricardo
  • Bairán García, Jesús Miguel
The corrosion of steel reinforcement is commonly believed to be the primary cause of structural deterioration of reinforced concrete (RC) structures; as a result of this deterioration, a RC structure can incur a considerable reduction in structural serviceability and safety. Because of their inherent redundancy, statically indeterminate structures develop resistant mechanisms that can potentially assist in delaying the collapse of severely damaged RC structures. In order to experimentally demonstrate these resistant mechanisms, four groups of three two-span continuous RC beam members each were deteriorated using induced corrosion methods and tested to failure under monotonic loads. For control, one group of three RC beams was left uncorroded and similarly load tested. All the RC beam specimens subjected to corrosion demonstrated a significant reduction (a maximum reduction of 55% as compared to the uncorroded control group) of their ultimate capacity. The presence of corrosion induced a transition from flexural failure to anchorage failure in some specimens; despite the induced damage some redistributed structural capacity was observed. Modelling of deterioration effects by the inclusion of different aspects of corrosion was also conducted. Three-dimensional (3D) Finite-Element Method (FEM) models were developed to assess the variation in the mechanical properties of the corroded steel and the reduction in the bond interaction between concrete and steel due to the corrosion of the steel reinforcement. In general, the current 3D FEM models demonstrated a good agreement with the experimental data; however, 3D FEM models that exhibit greater sophistication are necessary to better describe the failure mode of some RC beam specimens when they are associated with local effects., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Assessment of the efficiency of strengthening solutions in concrete structures by means of non-linear step by step analysis models, Evaluación de la eficiencia de soluciones de refuerzo en estructuras de hormigón mediante análisis no lineal evolutivo

  • Marí Bernat, Antonio Ricardo
  • Bairán García, Jesús Miguel
  • Oller Ibars, Eva
When designing a structural strengthening solution, the influence of the previous state of the structure on the capacity of the strengthened structure must be evaluated. In addition, strengthening interventions may involve operations such as partial unloading of the structure, placement and removal of temporary shores, application of loads or pre-deformations, restoring of damaged reinforcement or spalled con-crete or constraining of lateral strains. Therefore, changes in the cross-section geometry and reinforcement, longitudinal scheme, support conditions, loads and state of stresses and strains, may take place. Furthermore, occurrence of phenomena producing a premature failure or a change in the failure mode, should be avoided. In order to account for such a large variety of causes and phenomena affecting the structural response, a nonlinear and time-dependent analysis model of 3D reinforced and prestressed concrete frames, capable of capturing different failure modes and taking into account the structural history, is described. The model has been verified with tests on strengthened structures available in the literature and has been applied to an actually remodeled structure, comparing the advantages and disadvantages of two different strengthening proposals, showing its capabilities to assess the efficiency of structural strengthening systems., This paper is dedicated to the memory of an extraordinary engineer and human being, Luis Ortega Basagoiti, who was an example and reference for structural engineers and researchers along his professional career. The works described in this paper have been developed in the framework of the following research projects funded by the Spanish Science and Technology Ministries and by the European Funds for Regional Development, ADRESS (BIA2009-11764), REHABCAR (IPT-370000-2010-029), HORVITAL (BIA2015-64672-C4-1-R) and STRADURAVIUS (RTI2018-097314-B-C21)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

B-spline sectional model for general 3D effects in reinforced concrete elements

  • Poliotti, Mauro
  • Bairán García, Jesús Miguel
In this paper, an efficient sectional model for the nonlinear analysis of reinforced concrete elements sensible to 3D stress-components effects is presented. The classic plane-sections kinematic hypothesis is enhanced with a warping-distortion displacement field, which enables the model to reproduce the interaction between normal and tangential forces. The complementary field is obtained explicitly considering the inter-fiber equilibrium. This is solved using b-splines interpolation on the cross-section domain. The proposed method significantly reduces the number of unknowns compared with a finite element solution. The model is able to reproduce the interaction of longitudinal and transverse reinforcement with the concrete matrix. The validation shows that the presented model reproduces accurately complex failure modes as pure shear and coupling between bending and torsion. Further, as the transverse reinforcement is considered explicitly, confinement can be simulated in an objective manner. The presented model is an efficient tool for nonlinear analysis of reinforced concrete sections under general loading., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Safety factor calibration for a new model of shear strength of reinforced concrete building beams and slabs

  • Bairán García, Jesús Miguel
  • Casas Rius, Joan Ramon
When assessing existing structures, the availability of adequate safety factors, calibrated with the most accurate models, and for established target reliability indexes, is of critical importance in order to take the right decision regarding the maintenance/repair/strengthening interventions. In the case of shear resistance in reinforced concrete (RC) structures, when using the current design codes provisions for new constructions in assessment results that, in many cases, existing structures may be considered unsafe, implying large economic costs in strengthening or even dismantling. In this research, a proposal of safety factor relative to a recently developed model for shear strength, for elements with and without transversal reinforcement, based on a reliability-based calibration is presented. A formulation is proposed to determine the adequate strength factor for a selected target reliability index of the existing structure and desired remaining service life by means of a safety factor format, considering the load factors present in the Eurocodes. The calibration is carried out considering typical geometry and load ratios of building floors, as well as normal and high strength concrete. The derived safety factor is almost independent of the chosen remaining service life., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Embedded fibre reinforced polymer (FRP) reinforcement in concrete structures according to the new version of Eurocode 2, Armadura de polímeros reforzados con fibras (PRF) para estructuras de hormigón en la nueva versión del Eurocódigo 2

  • Oller Ibars, Eva
  • Torres Llinàs, Lluís
  • de Diego, Ana
The new version of Eurocode 2 will include for the first time an informative annex, Annex R “Embedded FRP reinforcement”, to design reinforced concrete structures with fibre reinforced polymer (FRP) reinforcement. FRP embedded reinforcement has some advantages such as their low susceptibility to corrosion, high-strength, and low life-cycle cost. FRP rebars can be used as longitudinal or transverse reinforcement in a similar way than conventional steel rebars. However, in the design of FRP reinforced concrete structures, some particular aspects related to the reinforcement properties must be taken into account, among which it is worth highlighting their linear elastic behaviour until failure, their relatively low modulus of elasticity or their behaviour under sustained stresses. Since, the content of Annex R is new, a summary and background related to all aspects required for designing with FRP reinforcement are given in this paper., The authors acknowledge the support provided by Spanish Ministry of Science and Innovation (MCIN/  AEI)  and  by  the  European  Funds  for  Regional  Development  in  the  following  projects  during their collaboration in the TN140/SC2 and in the CEN/TC250/SC2/WG1/TG1 (Eva Oller): BIA2015‐64672‐C4‐1‐R, RTI2018‐097314‐B‐C21, and PID2020‐119015GB‐C22., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Resistencia a punzonamiento de losas de hormigón armado sometidas a tracciones en su plano, Punching strength of reinforced concrete slabs subjected to in-plane tensile forces

  • Fernández Sánchez, Pablo Gonzalo
  • Marí Bernat, Antonio Ricardo
  • Oller Ibars, Eva
  • Duarte Gómez, Noemí
Se presentan los resultados de un estudio teórico y experimental de la resistencia a punzonamiento de placas sometidas a tracciones en su plano. Se han ensayado 10 losas de 1,65 x 1,65 x 0,12 metros, con dos cuantías diferentes de armadura, apoyadas en ocho puntos, sometidas a diversos niveles de tracción. Se observó que la carga última disminuye linealmente con la tracción aplicada, si bien, a partir de la plastificación de la armadura de flexión longitudinal, esta reducción es mayor. Las predicciones mediante modelos numéricos y mediante el modelo mecánico CCCM de resistencia a punzonamiento proporcionaron una excelente concordancia con los resultados experimentales., Los autores desean agradecer la financiación recibida del Ministerio de Ciencia e Innovación y de los Fondos Europeos de Desarrollo Regional (FEDER) a través del proyecto “Evaluación de la capacidad resistente frente a esfuerzos tangentes de estructuras de hormigón mediante modelos mecánicos para la extensión de su vida útil” BIA2015-64672-C4-1-R . Así mismo desean agradecer el apoyo del director del Laboratorio de Tecnología de Estructuras y Materiales de la UPC, de los técnicos y de los estudiantes de Master Magí Domingo y Laura Beltrán, quienes han contribuido a la realización de esta campaña experimental., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Punching-shear strength of reinforced concrete slabs subjected to unidirectional in-plane tensile forces

  • Fernández Sánchez, Pablo Gonzalo
  • Marí Bernat, Antonio Ricardo
  • Oller Ibars, Eva
This is the peer reviewed version of the following article: [Fernández, PG, Marí, A, Oller, E. Punching‐shear strength of reinforced concrete slabs subjected to unidirectional in‐plane tensile forces. Structural Concrete. 2020; 1– 16. https://doi.org/10.1002/suco.202000112], which has been published in final form at https://doi.org/10.1002/suco.202000112. This article may be used for non-commercial purposes in accordance with Wiley Terms and Conditions for Self-Archiving., Some reinforced concrete slabs are subjected simultaneously to concentrated loads and unidirectional in‐plane tensile forces. This the case of the top slab of a box girder bridge where hogging bending moments take place at the intermediate supports. Then, the in‐plane tensile forces may reduce the punching‐shear strength under concentrated loads. This paper describes an experimental campaign carried out to investigate the effect of unidirectional in‐plane tensile forces on the punching‐shear strength of RC slabs. A total of, five slabs (1,650 × 1,650 × 120 mm), subjected to different levels of in‐plane tensile forces were tested under a concentrated load up to failure. As observed, the punching‐shear strength diminishes almost linearly as the tensile force increases, up to a certain point associated to concrete cracking. From that point on, the reduction of punching strength is larger since the tensile force at the crack must be resisted by the reinforcement, which yields prematurely., This work has been carried out within the framework of the research project BIA-2015-64672-C4-1-R, financed by the Ministry of Economy and Competitiveness (MINECO) of Spain, and with the invaluable help of the technicians and the director of the Structural Technology Laboratory of the Polytechnic University of Catalonia. The authors want also to thank Master students Magí Domingo and Laura Beltran who collaborated in the numerical predictions and execution of the tests, respectively., Peer Reviewed, Postprint (author's final draft)