Skip to main content

Obtención de combustibles líquidos a partir de residuos plásticos de naturaleza poliolefínica

DI-16-08700

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprogram Subprograma Estatal de Formación
Call Doctorados Industriales
Call year 2016
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre URBASER SA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Simulation-assisted design of a catalytic hydrogenation reactor for plastic pyrolysis fuels

  • Gala Buro, Alberto Jesus
  • Catalán-Martínez, David
  • Guerrero, Marta
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] An enhancement of the properties of pyrolysis liquids (PL) from municipal plastic waste (mainly low-density polyethylene) by catalytic hydrotreatment is required to obtain automotive quality fuels. In this context, we report the design of a pilot catalytic hydrotreatment reactor using computational fluid dynamics (CFD). This modelling technique considered fluid flows, gas diffusion, olefin hydrogenation reactions, and heat transfer. The built model allowed the development of different sensitive analysis to evaluate the influence of spatial time, heat transfer fluid (used as a reactor coolant) and hydrogen/pyrolysis liquid ratio. Possible phase changes (from gas to liquid) were analyzed by a thermodynamic approach. The results showed that the refrigerant oil allows alleviating possible temperature gradients arising from the exothermic hydrogenation reaction. It was also found that the system can be optimized in order to minimize the energy cost by adjusting the inlet temperature of the reactive gas (H2) and the refrigerant oil flow. Condensations in the reactive chamber could be avoided by working at intermediate pressures (40¿60 bar) and/or increasing the feed of H2. Additionally, the results obtained with the CFD 3D model together with the condensation analysis allowed to optimize the operational regime and the pilot-reactor design in terms of dimensioning and construction materials., The authors acknowledge the financial support of the Centre for the Development of Industrial Technology [grant number IDI -20150730] and the Ministerio de Ciencia, Innovacion y Universidades (Spain) [grant number DI - 16 - 08700]
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Characterization and Distillation of Pyrolysis Liquids Coming from Polyolefins Segregated of MSW for Their Use as Automotive Diesel Fuel

  • Gala, Alberto
  • Guerrero, Marta
  • Guirao, Beatriz
  • Domine, Marcelo Eduardo
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] The liquids resulting from pyrolysis of industrial plastic waste (IPW) and postconsumer colored and white plastic film waste (PCPW and PWPW, respectively) at the pilot scale (80 kg/h) were widely characterized by different techniques to assess their potential as both petrochemical raw material and automotive diesel fuel. It was found that pyrolysis liquids mainly consisted of hydrocarbons in the diesel boiling point range (180-380 degrees C), amounting to approximately 50-55 vol %. Therefore, the results were further contrasted with limits established by the EN 590:2014 + A1:2017 standard for automotive diesel fuel. Although pyrolysis liquids showed good properties, they do not conform to some key fuel parameters for diesel engines, such as density, distillation curve, kinematic viscosity, flash point, and cold filter plugging point. To improve these properties, PWPW pyrolysis liquids were distilled in the diesel range and the liquid fractions were characterized according to automotive diesel standards. It was found that the diesel fraction met all specifications with the exception of the cold filter plugging point (-10 to 4 degrees C vs -10 degrees C winter/0 degrees C summer) and density (800-807 vs 820 kg/m(3)). To accomplish these standards, a blend of diesel obtained from PWPW pyrolysis liquids and commercial diesel (50/50 wt %) was also prepared and analyzed. Results revealed that the blend met the requirements of the 21 parameters demanded by the standard for a product to be marketed and used as automotive fuel in diesel engine vehicles., The authors acknowledge the financial support of the Centre for the Development of Industrial Technology (grant number IDI-20150730) and the Ministerio de Ciencia, Innovacion y Universidades (Spain) (grant number DI-16-08700).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Characterization of post-consumer plastic film waste from mixed MSW in Spain: A key point for the successful implementation of sustainable plastic waste management strategies

  • Gala, Alberto
  • Guerrero, Marta
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] The purpose of this paper is to provide a full characterization of post-consumer plastic film recovered from mixed municipal solid waste (MSW) treatment plants in Spain. Currently, this type of plastic waste is not recycled due to technical or economic barriers and is still sent to landfill. Different types of municipal plastic waste (MPW) from manual and automated sorting were studied: i) colour plastic film recovered by ballistic separators and then manual sorting in different seasons; ii) colour plastic film recovered by automated sorting (air suction); and iii) white plastic film from primary manual sorting process. The samples were characterized by different techniques, including the ultimate and proximate analysis, Higher Heating Value (HHV) and Lower Heating Value (LHV), metal content, Thermogravimetric Analysis (TGA) and Derivative Thermogravimetry (DTG), Fourier Transform Infrared (FT-IR) analysis and Differential Scanning Calorimetry (DSC). The results were compared to those obtained for pretreated colour and white plastic film waste and contrasted with industrial recycled film granules of polyethylene (as a reference material for packaging film). Additionally, pretreated plastic film samples were also characterized by analyzing viscosity, Pressure-Volume-Temperature (PVT) diagram, specific heat capacity and halogen and sulphur contents. Characterization data from this study will contribute to identify and develop potential recycling alternatives for a more sustainable municipal plastic waste management, which is recognized as a priority in the European Circular Economy Action Plan to use resources in a more sustainable way., The authors acknowledge the financial support of the Centre for the Development of Industrial Technology [grant number IDI - 20181081] and the Ministerio de Ciencia, Innovacion y Universidades (Spain) [grant number DI - 16 - 08700].