Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Using momentum flux measurements to determine the injection rate of a commercial Urea Water Solution injector

  • Payri, Raul|||0000-0001-7428-5510
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Moreno-Gasparotto, Armando Enrique
[EN] The Selective Catalytic Reduction (SCR) technology allows the transformation of the Nitrous Oxide emissions present in exhaust gases into gaseous nitrogen and water. For a proper operation of the SCR, a urea-water solution (UWS) injector must dose an adequate amount of liquid into the exhaust pipe in order to avoid deposit formation and to guarantee the SCR system efficiency. This task requires the knowledge of the performance of the injector. Then, the goal of this work is to study the hydraulic performance of a UWS injector, by means of measuring the spray momentum flux in order to understand the influence of different variables as injected fluid, injection pressure, counter pressure and cooling temperature of the injector on the flow characteristics. The tested injector was cooled at three different temperatures, 60, 90 and 120 degrees C, the injection pressure of the UWS was set at 5, 7 and 9 bar, with counter pressures of 750, 900, 1000 and 2000 mbar for the two tested fluids, water and UWS. The measurements were carried out using an experimental facility developed at CMT-Motores Termicos for the determination of spray momentum flux, where a piezoelectric pressure sensor was located near the nozzle exit of the injector, which measures the impact force of the spray. Additionally, the proposed methodology allowed to determine the injected mass flow and to capture the transient injection events, such as the opening and closing stages. Moreover, mass flow rate measurements of the injector were performed under the same operating conditions, determining the influence of the injection pressure, cooling temperature, counter pressure and fluid properties. Regarding the pressure, the tendency was as expected, the higher the injection pressure the higher the Momentum flux and flow rate. Results showed that an increment of the cooling temperature of the injector induces the appearance of flash boiling conditions, having an impact on the total injected mass and momentum flux, changing the behaviour of the spray. For the same conditions, water has a higher momentum flux than the UWS due to differences in fluid properties and velocity at the nozzle exit., This work has been partially funded by Spanish Ministerio de Ciencia, Innovacion y Universidades through project RTI2018099706B100. The author A. Moreno thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI2018S213) , which is included within the framework of Programa de Apoyo para la Investigacion y Desarrollo (PAID).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental approach for the analysis of the flow behaviour in the stator of a real centripetal turbine

  • Galindo, José|||0000-0001-6068-182X
  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Hervás-Gómez, Natalia
[EN] During normal operation, radial turbines may work in off-design conditions. Off-design conditions may be characterised by very low expansion ratios, very high expansion ratios, very low rotational speeds or very high rotational speeds. All of these cases are difficult to characterise experimentally due to high experimental uncertainties or a lack of capabilities in the system feeding pressurised air to the turbine. Also, there are two- and three-dimensional computational fluid dynamics simulations at these operating points but could not be accurate enough due to high turbulence effects, flow detachment and shock wave generation. With a lack of high-quality data, experimental or computational, to fit the reduced-order turbine models used in zero- and one-dimensional engine simulations, there are large uncertainties associated to their results in off-design conditions. This work develops an experimental facility able to characterise the internal flow of radial turbine stators in terms of pressure and velocity fields at off-design and regular working conditions. The facility consists of an upscaled model of a radial turbine volute and stator fed with air in pressure- and temperature-controlled conditions, so different sensors can be used inside it with the least amount of flow disturbance. The different restrictions considered in the design of the upscaled model are presented, and their effects in the final experimental apparatus capabilities are discussed. A preliminary comparison between computational fluid dynamics simulations and experimental data shows encouraging results., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This work was partly sponsored by the programme 'Ayuda a Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia (UPV), Spain'. The support given to Ms N.H.G. by Universitat Politecnica de Valencia through the 'FPI-Subprograma 2' (No. FPI-2018-S2-1368) grant within the 'Programa de Apoyo para la Investigacion y Desarrollo (PAID-0118)' is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Design and Numerical Analysis of Flow Characteristics in a Scaled Volute and Vaned Nozzle of Radial Turbocharger Turbines

  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • Navarro, Roberto|||0000-0003-2587-4954
  • Inhestern, Lukas Benjamin
  • Hervás-Gómez, Natalia
[EN] Over the past few decades, the aerodynamic improvements of turbocharger turbines contributed significantly to the overall efficiency augmentation and the advancements in downsizing of internal combustion engines. Due to the compact size of automotive turbochargers, the experimental measurement of the complex internal aerodynamics has been insufficiently studied. Hence, turbine designs mostly rely on the results of numerical simulations and the validation of zero-dimensional parameters as efficiency and reduced mass flow. To push the aerodynamic development even further, a precise validation of three-dimensional flow patterns predicted by applied computational fluid dynamics (CFD) methods is in need. This paper presents the design of an up-scaled volute-stator model, which allows optical experimental measurement techniques. In a preliminary step, numerical results indicate that the enlarged geometry will be representative of the flow patterns and characteristic non-dimensional numbers at defined flow sections of the real size turbine. Limitations due to rotor-stator interactions are highlighted. Measurement sections of interest for available measurement techniques are predefined., The authors disclose receipt of the following financial support for the research, authorship, and/or publication of this article: This work was partly sponsored by the program "Ayuda a Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia (UPV), Spain". The support given to Ms. N.H.G. by Universitat Politecnica de Valencia through the "FPI-Subprograma 2" (No.FPI-2018-S2-1368) grant within the "Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-18)" is gratefully acknowledged