Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Compensation of phase noise impairments in distributed acoustic sensors based on optical pulse compression time-domain reflectometry

  • Piñeiro Ben, Enrique
  • Sagüés García, Mikel
  • Loayssa Lara, Alayn
We introduce a method to compensate for the deleterious effects of the phase noise of the laser source on long-range distributed acoustic sensors (DAS) that implement optical pulse compression (OPC). Pulse compression can be used in coherent optical time-domain reflectometry (COTDR) sensors to extend the measurement range without compromising spatial resolution. In fact, OPC-COTDR sensors have demonstrated the longest measurement range to date in passive sensing links that do not require distributed amplification to compensate fiber attenuation. However, it has been found that the limited coherence of the laser source has a degrading effect on the actual performance enhancement that pulse compression can bring because it constrains the maximum duration of the compression waveforms that can be used and makes the use of lasers with extremely low phase noise necessary.We introduce a technique to compensate for the effects of phase noise on OPC-COTDR sensors so that they can demonstrate their full potential for long-range measurements using lasers with less stringent phase noise requirements. The method is based on sampling the phase noise of the laser with an auxiliary interferometer and using this information in a simple signal processing technique to mitigate its deleterious effect on the signal measured. We test our method in an OPCCOTDR sensor that uses 500-μs linear frequency modulated pulses to demonstrate 100-km range measurements with 200 p/√Hz of strain sensitivity at 2-m initial spatial resolution that becomes 10-m after applying the gauge length. To our knowledge, this is the longest compression waveform demonstrated to date in an OPCCOTDR sensor. Its use provides an extra 20-km range compared to previous demonstrations using laser sources of comparable linewidth. Furthermore, comparable performance is also demonstrated when using a laser source with an order of magnitude larger linewidth., This work was supported in part by European Union “Next generationEU”/PRTR and MCIN/AEI/10.13039/501100011033 under grant PDC2021-121172-C21, in part by FEDER “A way to make Europe” and MCIN/AEI/10.13039/501100011033 under Grant PID2019-107270RB-C22, and in part by the Gobierno de Navarra under Grant PC210-211 FIBRATRAFIC.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

C and L band fiber lasers enhanced by ultrafast laser inscribed artificial backscatter reflectors

  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Sánchez González, Arturo
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
This letter presents an experimental comparison between two linear-cavity erbiumdoped fiber lasers (EDFL) assisted by two different artificial backscatter fiber-based reflectors. Both reflectors were inscribed by femtosecond laser direct writing, one of them within a single-mode fiber (SMF) and the other one within a multi-mode fiber (MMF). Although the erbium-doped fiber amplifier (EDFA) used in both structures was the same and both reflectors were manufactured under the same parameters, the reflection spectrum of each was clearly different due to their different physical properties. The first linear-cavity EDFL, consisting of an SMF-based reflector with 9µm core and 125µm cladding, resulted in a single laser emission line located in the C-band and centered at 1564.4 nm, exhibiting an optical signal-to-noise ratio (OSNR) of 52dB when pumped at 100mW. On the other hand, a single laser emission line with a similar OSNR but in L-band (centered at 1574.5nm) was obtained when using an MMF-based reflector with 50µm core and 125µm cladding., Ministerio de Educacion, Cultura y Deporte (PhD grant FPU2018/02797); European Commission (Next generation EU/PTR); FEDER (A way to make Europe); MCIN/AEI/10.13039/501100011033 (PDC2021-121172-C21, PID2019-107270RB).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Wavelength-switchable L-band fiber laser assisted by random reflectors

  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Sánchez González, Arturo
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
A wavelength-switchable L-band erbium-doped fiber laser (EDFL) assisted by an artificially controlled backscattering (ACB) fiber reflector is here presented. This random reflector was inscribed by femtosecond (fs) laser direct writing on the axial axis of a multimode fiber with 50 lm core and 125 lm cladding with a length of 17 mm. This microstructure was placed inside a surgical syringe to be positioned in the center of a high-precision rotation mount to accurately control its angle of rotation. Only by rotating this mount, three different output spectra were obtained: a single wavelength lasing centered at 1574.75 nm, a dual wavelength lasing centered at 1574.75 nm and 1575.75 nm, and a single wavelength lasing centered at 1575.5 nm. All of them showed an optical signal-to-noise ratio (OSNR) of around 60 dB when pumped at 300 mW, This work was financed by the program "José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores", funded by the Ministerio de Universidades of Spain (reference CAS21/00351); the Spanish AEI projects PID2019-107270RB, funded by MCIN/AEI/10.13039/501100011033 and FEDER "A way to make Europe", and projects PDC2021-121172 and TED2021-130378B funded by MCIN/ AEI/10.13039/501100011033 and European Union "Next generation EU"/PTR. Finally, the work was also founded by the Ministerio de Educación, Cultura y Deporte of Spain (PhD grant FPU2018/02797).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Method to use transport microsimulation models to create synthetic distributed acoustic sensing datasets

  • Robles Urquijo, Ignacio
  • Benavente, Juan
  • Blanco García, Javier
  • Diego González, Pelayo
  • Loayssa Lara, Alayn
  • Sagüés García, Mikel
  • Rodríguez Cobo, Luis
  • Cobo, Adolfo
This research introduces a new method for creating synthetic Distributed Acoustic Sensing (DAS) datasets from transport microsimulation models. The process involves modeling detailed vehicle interactions, trajectories, and characteristics from the PTV VISSIM transport microsimulation tool. It then applies the Flamant-Boussinesq approximation to simulate the resulting ground deformation detected by virtual fiber-optic cables. These synthetic DAS signals serve as large-scale, scenario-controlled, labeled datasets on training machine learning models for various transport applications. We demonstrate this by training several U-Net convolutional neural networks to enhance spatial resolution (reducing it to half the original gauge length), filtering traffic signals by vehicle direction, and simulating the effects of alternative cable layouts. The methodology is tested using simulations of real road scenarios, featuring a fiber-optic cable buried along the westbound shoulder with sections deviating from the roadside. The U-Net models, trained solely on synthetic data, showed promising performance (e.g., validation MSE down to 0.0015 for directional filtering) and improved the detectability of faint signals, like bicycles among heavy vehicles, when applied to real DAS measurements from the test site. This framework uniquely integrates detailed traffic modeling with DAS physics, providing a novel tool to develop and evaluate DAS signal processing techniques, optimize cable layout deployments, and advance DAS applications in complex transportation monitoring scenarios. Creating such a procedure offers significant potential for advancing the application of DAS in transportation monitoring and smart city initiatives., This research was funded by the Spanish Goverment 'Subprograma Ayudas Predoctorales 2020 Investigadores' program under Grant PRE2020-096336, assigned to the National Plan project PID2019-107270RB-C21, 'Photonic Devices and Systems Sensors for Intelligent Structures and Non Destructive Evaluation I'; the National 'Knowledge Generation Projects' project 'Photonic Sensors for Smart and Sustainable Cities (Performance)' under grant ID6448137269-137269-4-22; the project 'Integrated System for Traffic and Road Condition Monitoring Using Fiber-Optic Sensors (Ingestion)', under grant PDC2021-121172-C22 funded by MICIU/AEI/10.13039/501100011033 and by the European Union Next GenerationEU/PRTR). This work was supported in part by grant PID2022-137269OB-C21 by MICIU/AEI/10.13039/501100011033 and by ERDF 'A way of making Europe'; and grant PID2022-137269OB-C22 by MICIU/AEI/10.13039/501100011033 and by the European Union.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Ring cavity erbium-doped fiber for refractive index measurements

  • Pérez Herrera, Rosa Ana
  • Soares, Liliana
  • Silva, Susana
  • Frazão, Orlando
In this study, an interrogation system based on an erbium-doped fiber ring cavity for refractive index measurements is presented and experimentally demonstrated. This cavity ring includes a 1 × 3 coupler wherein one of the fiber output ports is used to increase the optical power of the system by means of an FBG used as a reflector. The other two output ports are used as a refractive index sensing head and reference port, respectively. An experimental demonstration of this proposed sensor system for the measurement of a distinct refractive index is presented., This work is financed by the program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Universidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PTR; and National Funds through the Portuguese funding agency, FCT—Fundação para a Ciência e a Tecnologia, within project UIDB/50014/2020. Liliana Soares acknowledges the support of FCT, Portugal through the Grant 2020.05297.BD.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Study of in-line capillary fiber sensor for uniaxial transverse deformation

  • Sánchez González, Arturo
  • Leandro González, Daniel
  • Dauliat, Romain
  • Jamier, Raphael
  • Roy, Philippe
  • Pérez Herrera, Rosa Ana
This research explores the impact of cyclic uniaxial transverse deformation on an in-line hollow-core fiber etalon. The structure consists of a 6 mm long section of capillary fiber spliced between two standard single-mode fibers. The optical response of the structure is theoretically analyzed in spectral and transformed domains, evidencing Fabry-Perot and antiresonant interferometric mechanisms. A validation of the theoretical behavior is carried out both through simulation and experimentation. The performance of the structure for uniaxial transverse deformation is subsequently evaluated by tracking the phase of the main component in the transformed domain. The relevance of measuring in the time domain is discussed, demonstrating improved accuracy over wavelength shift and inverse spatial domain methods. Several sensors with different internal diameters underwent cycles of transverse deformation, revealing robust linear trends in every case. On average, the structure demonstrated elastic behavior under deformations up to 42 μm, with a mean sensitivity of 0.174 rad/μm, and mechanical breakage taking place at 58 μm. The results confirmed the suitability of the sensor to withstand uniaxial micro-displacements or pressures, with smaller inner diameter capillary fibers showing the best performance., This work was supported in part by MCIN/AEI/10.13039/501100011033 and FEDER "A way to make Europe" under Project PID2019-107270RB-C22 and Project PID2022-137269OB-C21, in part by MCIN/AEI/10.13039/501100011033 and European Union "Next generation EU"/PRTR under Project PDC2021-121172-C21 and Project TED2021- 130378B-C22, and in part by the Public University of Navarre under Project PJUPNA06-2022. Open access funding provided by Public University of Navarre.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Long-range traffic monitoring based on pulse-compression distributed acoustic sensing and advanced vehicle tracking and classification algorithm

  • Corera Orzanco, Íñigo
  • Piñeiro Ben, Enrique
  • Navallas Irujo, Javier
  • Sagüés García, Mikel
  • Loayssa Lara, Alayn
We introduce a novel long-range traffic monitoring system for vehicle detection, tracking, and classification based on fiber-optic distributed acoustic sensing (DAS). High resolution and long range are provided by the use of an optimized setup incorporating pulse compression, which, to our knowledge, is the first time that is applied to a traffic-monitoring DAS system. The raw data acquired with this sensor feeds an automatic vehicle detection and tracking algorithm based on a novel transformed domain that can be regarded as an evolution of the Hough Transform operating with non-binary valued signals. The detection of vehicles is performed by calculating the local maxima in the transformed domain for a given time-distance processing block of the detected signal. Then, an automatic tracking algorithm, which relies on a moving window paradigm, identifies the trajectory of the vehicle. Hence, the output of the tracking stage is a set of trajectories, each of which can be regarded as a vehicle passing event from which a vehicle signature can be extracted. This signature is unique for each vehicle, allowing us to implement a machine-learning algorithm for vehicle classification purposes. The system has been experimentally tested by performing measurements using dark fiber in a telecommunication fiber cable running in a buried conduit along 40 km of a road open to traffic. Excellent results were obtained, with a general classification rate of 97.7% for detecting vehicle passing events and 99.6% and 85.7% for specific car and truck passing events, respectively., This work was supported in part by European Union “Next generationEU”/PRTR and MCIN/AEI/10.13039/501100011033 under grant PDC2021-121172-C21, in part by FEDER “A way to make Europe” and MCIN/AEI/10.13039/501100011033 under grant PID2019-107270RB, and in part by Gobierno de Navarra under grant PC210-211 FIBRATRAFIC.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

High performance fiber laser resonator for dual band (C and L) sensing

  • Sánchez González, Arturo
  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
This work presents an experimental analysis and comparison of the performance of quasi-randomly distributed reflectors inscribed into a single-mode fiber as a sensing mirror both in C- and L-band. Single-wavelength emission has been obtained in either band when using these artificially controlled backscattering fiber reflectors in a ring-cavity fiber laser. Single-longitudinal mode operation with an optical signal to noise ratio (OSNR) of 47 dB and an output power instability as low as 0.04 dB have been measured when employing a C-band optical amplifier. When replaced by an L-band optical amplifier, a single-longitudinal mode behavior has also been obtained, showing an OSNR of 44 dB and an output power instability of 0.09 dB. Regarding their performance as fiber-laser sensing systems, very similar temperature and strain sensitivities have been obtained in both bands, comparable to fiber Bragg grating sensors in the case of temperature and one order of magnitude higher in the case of strain variations., and European Union “Next generationEU”/PTR.This work is part of the project PID2019-107270RB, funded by MCIN/ AEI/10.13039/501100011033 and FEDER “A way to make Europe”, the Ministerio de Educación, Cultura y Deporte of Spain (PhD grant FPU2018/02797), and PDC2021-121172, funded by MCIN/ AEI/10.13039/501100011033
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Paracetamol concentration-sensing scheme based on a linear cavity fiber laser configuration

  • Soares, Liliana
  • Pérez Herrera, Rosa Ana
  • Novais, Susana
  • Ferreira, António
  • Frazão, Orlando
  • Silva, Susana
A paracetamol concentration-sensing scheme based on a linear cavity fiber laser configuration is demonstrated experimentally. The laser cavity has a fiber sensor at one end, that allows refractive index measurements. The refractometer consists of a cleaved fiber tip combined with an FBG functioning as a reflecting mirror. The combination of a fiber loop mirror at the other end allows to reflect all the light from the FBG and refractometer, forming a linear cavity. By measuring the intensity variation of the Fresnel reflection at the fiber-to-liquid interface, the measured concentration is linear and have a concentration sensitivity of -8.74±0.34×10-5 µW/(g/kg), over a range of 52.61 to 219.25 g/kg, and with a resolution of 2.77 g/kg. The results obtained present high stability and prove the potential of the fiber laser system to performed real-time measurements of concentration, in a non-invasive way., This research was funded by: National Funds through the Portuguese funding agency, FCT - Fundação para a Ciência e a Tecnologia, within project UIDB/50014/2020; National Funds through FCT/MCTES (PIDDAC), within projects LA/P/0045/2020 (ALiCE), UIDB/00511/2020 and UIDP/00511/2020 (LEPABE); Program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Univesidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021-130378B-C22 funded by MCIN/ AEI/https://doi.org/10.13039/501100011033 and European Union “Next generation EU”/PTR. Liliana Soares acknowledges the support of FCT, Portugal, through the Grant 2020.05297.BD.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Measurement of paracetamol concentration using an erbium-doped fiber ring cavity

  • Soares, Liliana
  • Pérez Herrera, Rosa Ana
  • Novais, Susana
  • Ferreira, António
  • Silva, Susana
  • Frazão, Orlando
Process Analytical Technology (PAT) has been increasingly used in the pharmaceutical industry to monitor essential parameters in real-time during pharmaceutical processes. The concentration of Active Pharmaceutical Ingredients (APIs), such as paracetamol, is one of these parameters, and controlling its variations allows for optimization of the production process. In this study, a refractometric sensor, implemented by an interrogation system based on an Erbium-Doped Fiber Ring Cavity (EDFRC), was presented and experimentally demonstrated. The Cavity Ring proposed included a 1 × 3 coupler. One port of the coupler was used to increase the optical power of the system through a Fiber Bragg Grating (FBG), and the other two ports were used as sensing head and reference. The sensor detected variations of paracetamol concentration with a sensitivity of [(−1.00 ± 0.05) × 10−3] nW/(g/kg) and a resolution of 5.53 g/kg. The results demonstrate the potential of this technology as a possible non-invasive PAT tool., and European Union “Next generation EU”/PTR. Liliana Soares acknowledges the support of FCT, Portugal, through the Grant 2020.05297.BD.This research was funded by: National Funds through the Portuguese funding agency, FCT—Fundação para a Ciência e a Tecnologia, within project UIDB/50014/2020; National Funds through FCT/MCTES (PIDDAC), within projects LA/P/0045/2020 (ALiCE), UIDB/00511/2020, and UIDP/00511/2020 (LEPABE); Program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Univesidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021-130378B-C22, funded by MCIN/AEI/10.13039/501100011033