Skip to main content

ESTABLECIMIENTO DE UNA METODOLOGIA PARA LA OBTENCION DE MATERIALES CON GRADIENTE DE CONCENTRACION BIDIMENSIONAL MEDIANTE LA DEPOSICION DIRECTA DE MATERIALES CON LASER

RTI2018-096472-B-I00

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2018
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSIDADE DA CORUÑA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of alloying elements on laser surface modification of powder metallurgy to improve surface mechanical properties of beta titanium alloys for biomedical application

  • Rossi, M. C.
  • Amado, J. M.
  • Tobar, M. J.
  • Yáñez, A.
  • Vicente-Escuder, Ángel|||0000-0001-8425-3424
  • Amigó, Vicente|||0000-0002-2107-0273
[EN] Beta-type titanium alloy surfaces (Tie35Nbe10Ta (TNT) and Tie30Nbe4Sn (TNS)) were modified by laser using a power of 1000Wand speed of 6.7 mm/s (Condition A) and a power of 1500 W with speed of 10 mm/s (Condition B). Increasing laser conditions, the thickness of the molten layer was also increased. The initial equiaxed grains changes to quite elongated grains shape. The surfaces were structured under alfa" martensite, alfa and matrix beta. The beta phase content decreased slightly and the alfa" phase increased for both alloys increasing the laser conditions. The condition A increased the elastic modulus (E) and decreased the hardness while condition B did not affect the mechanical properties surface for the TNT system compared to base metal (BM). In TNS system the laser condition A decreased the E and increased the hardness while increasing the laser parameters (Condition B) both E and hardness decreased compared to BM. The laser surface treatment was influenced by the levels of alloying elements present promoting most significant changes in the microstructure and mechanical properties in the TNS system., This work was supported by the Ministerio Espan~ol de Ciencia, Innovaci?on y Universidades, Spain with Grant RTI2018-097810-B-I00, RTI2018-096472-B-I00 and the European Union (EU) through Fondo Europeo de Desarrollo Regional (FEDER) , Spain.
RUC. Repositorio da Universidade da Coruña
Publication Artículo científico (JournalArticle)

Laser Surface Modification in Ti-xNb-yMo Alloys Prepared by Powder Metallurgy

  • Tendero, Inmaculada
  • Rossi, Mariana
  • Viera, Mauricio
  • Amado, José
  • Tobar, M.J.
  • Vicente-Escuder, Ángel
  • Yáñez, Armando
  • Amigó, Vicente
[Abstract] The main objective was to study the effect of surface modification by laser on Ti-Nb-Mo powder metallurgical alloys to improve their mechano-chemical behavior and their application as a biomedical implant. The used powder mixtures were produced in an inert atmosphere. Uniaxial compaction took place at 600 MPa with high-vacuum sintering at 1250 °C for 3 h. The specimens for the three-point flexure test were prepared and their mechanical properties determined. Microstructural characterization was performed by scanning electron microscopy (SEM) and X-ray diffraction (XRD) to obtain the distribution of phases, porosity, size, and shape of the grains of each alloy. Corrosion behavior was evaluated by electrochemical tests using an artificial saliva electrolyte modified from Fusayama at 37 °C. Chemical characterization was completed by analyzing the ionic release by Inductively coupled plasma atomic emission spectroscopy (ICP-EOS) after immersion for 730 h in Fusayama solution modified with NaF at 37 °C to simulate a 20-year life span based on a daily 2-min cycle of three toothbrushes. Corrosion behavior confirmed promising possibilities for the biomedicine field. The surface porosity of the samples not submitted to surface treatment deteriorated properties against corrosion and ion release. The obtained phase was β, with a low α”-martensite percentage. The maximum resistance to bending was greater after surface fusion. Plastic deformations were above 7% under some conditions. Microhardness came close to 300 HV in heat-affected zone (HAZ) and 350 HV in fusion zone (FZ) (under the determined condition. The elastic modulus lowered by around 10%. The corrosion rate was lower in Ti-27Nb-8Mo and Ti-35Nb-6Mo. Niobium release was significant, but below the physiological limit., The authors thank the Ministerio de Economía y Competitividad de España for Research Project RTI2018-097810-B-I00 and the Ministerio de Economía y Competitividad de España for Research Project RTI2018-096472-B-I00. The European Commission thanks to FEDER and the São Paulo State Research Support Foundation (FAPESP) [Grant: 2019/24237-6]., Fundação de Amparo à Pesquisa do Estado de São Paulo; 2019/24237-6
RUC. Repositorio da Universidade da Coruña
Publication Artículo científico (JournalArticle)

Effect of Alloying Elements on Laser Surface Modification of Powder Metallurgy to Improve Surface Mechanical Properties of Beta Titanium Alloys for Biomedical Application

  • Rossi, Mariana
  • Amado, José
  • Tobar, M.J.
  • Vicente-Escuder, Ángel
  • Yáñez, Armando
  • Amigó, Vicente
[Abstract] Beta-type titanium alloy surfaces (Tie35Nbe10Ta (TNT) and Tie30Nbe4Sn (TNS)) weremodified by laser using a power of 1000 W and speed of 6.7 mm/s (Condition A) and a powerof 1500 W with speed of 10 mm/s (Condition B). Increasing laser conditions, the thicknessof the molten layer was also increased. The initial equiaxed grains changes to quiteelongated grains shape. The surfaces were structured undera00martensite,aand matrixb.Thebphase content decreased slightly and thea00phase increased for both alloysincreasing the laser conditions. The condition A increased the elastic modulus (E) anddecreased the hardness while condition B did not affect the mechanical properties surfacefor the TNT system compared to base metal (BM). In TNS system the laser condition Adecreased the E and increased the hardness while increasing the laser parameters (Con-dition B) both E and hardness decreased compared to BM. The laser surface treatment wasinfluenced by the levels of alloying elements present promoting most significant changesin the microstructure and mechanical properties in the TNS system, This work was supported by the Ministerio Español de Ciencia, Innovación y Universidades, Spain with Grant RTI2018-097810-B-I00, RTI2018-096472-B-I00 and the European Union (EU) through Fondo Europeo de Desarrollo Regional (FEDER), Spain