Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental characterization of direct injection liquid ammonia sprays under non-reacting Diesel-like conditions

  • Payri, Raul|||0000-0001-7428-5510
  • García-Oliver, José M|||0000-0002-2676-9681
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Cao, Jiawei
[EN] Ammonia is seen as a promising fuel to replace fossil fuels internal combustion engines, given the advantages of zero carbon emission and extensive experience in its synthesis at large scale. The ignition of ammonia in direct injection engine is still a challenge due to its unfavorable combustion characteristics, but the investigation of ammonia spray characteristics is an important step to shed light on the optimum combustion strategy. In this paper, the evolution of direct injection ammonia sprays was measured at engine-like conditions generated in a constant pressure facility by means of diffused back-illumination imaging and schlieren. In a first step, ammonia spray behavior is compared against that of Diesel fuel. Experimental results show a slower penetration of ammonia mainly due to a lagging starting penetration phase, which cannot be later recovered. In terms of liquid length, initial stages show the same pattern as for ammonia, while a shorter stabilized liquid length can be observed. Parametric trends over different operating conditions show a similar behavior to Diesel against ambient density and temperature, as well as with injection pressure and nozzle diameter. Such results, backed up by the application of a 1D spray model developed for Diesel -like fuels, suggest that ammonia sprays under nonreacting conditions have a mixing-controlled evolution., This research has been partially funded by MCIN/AEI/10.13039/501100011033 and the European Union"NextGenerationEU"/PRTR as part of the project DIGIAMMONIA TED2021-129379A-I00. We also acknowledge the finance support from Chinese Scholarship Council (No. 201808320236) . We would like to thank Jose Enrique del Rey and Omar Huerta for their valuable support during the experimental campaign.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Numerical investigation of direct ammonia injection and combustion

  • Di Matteo, Andrea
  • Somers, Bart
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Daniel
[EN] A numerical investigation of ammonia direct injection is presented in this work. Injection is initially conducted through a single-hole ECN-like nozzle into a constant volume chamber. The performance of break-up and turbulence models is assessed and the mesh is validated in non-reacting conditions against experimental data. The results, in terms of spray tip penetration and liquid length, show good agreement with experiments, although an overprediction is observed in the initial transient phase of the spray tip penetration. For the reacting case, a flamelet tabulated manifold (FGM) model is used. 1D flamelet studies and 3D Spray D-like studies, provide the initial conditions favoring the auto-ignition of ammonia. All cases analyzed, ranging in temperature from 1200 to 1300 K and in pressure from 79 to 113 bar, show ignition, in very different ranges. However, only the marine-engine derived case ("Case 3") is providing a stable lifted flame. Therefore, Case 3 is chosen to study a marine-like combustion chamber (SCC), in which ammonia is injected via a multi-hole injector. To replicate the conditions in the real application, the pilot diesel injection is treated in a simplified manner, with only the temperature and pressure rise taken into account. The conditions studied refer to two positions of the pilot injection with respect to the main ammonia injection. The results are encouraging, as both solutions show ignition. The second, considering a pilot very close to the ammonia injector, also shows a stable lifted flame for approximate to 8 ms. However, it should be noted that no experimental data are currently available for any of the reacting conditions of both the Spray D-like and marine-like cases. The study is therefore purely exploratory, mostly providing best practices and approaches, and suggesting the conditions that can be tested in real hardware in the future., This research has been partially funded by MCIN/AEI/10.13039/501100011033 and the European Union "NextGenerationEU"/PRTR as part of the project DIGIAMMONIA TED2021-129379A-I00.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Comparative life cycle assessment of oxy-fuel combustion utilization across various fuels in the maritime sector

  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • Sanchis, Enrique José|||0000-0002-6856-8992
  • Francisco Javier
[EN] This paper, aligned with the International Maritime Organization's 2050 decarbonization goals, examines the lifecycle assessment (LCA) of marine fuels - both conventional and alternative - used in oxy-fuel combustion (OFC) technology with onboard CO2 capture. It offers a novel analysis of OFC in the maritime sector, utilizing stored O2 for combustion to eliminate nitrogen oxides (NOx) and capture CO2. The study also explores producing e-fuels (e-diesel and e-methanol) from H2 and captured CO2 to establish a closed-loop carbon cycle. In addition to e-fuels, biodiesel is evaluated as an alternative fuel, with heavy fuel oil (HFO) and liquefied natural gas (LNG) serving as conventional benchmarks. Ammonia is assessed as a non-carbon-based fuel for comparison. Using GREET 2024 for LCA inventory, this research compares CO2 emissions from carbon-based fuels under both conventional combustion and OFC in current and 2050 scenarios. Results show that OFC reduces CO2 HFO emissions from 90,000 mg/MJ to 25,000 mg/MJ. Biodiesel with OFC and CO2 capture achieves net-negative emissions (-37,841 mg/MJ). Ammonia achieves emission reductions over conventional fuels if CO2 is captured in the Steam Methane Reforming (SMR) process. By 2050, with H2 produced through electrolysis, e-fuel emissions are expected to decrease by up to 6,042 mg/MJ, a decrease of 84% compared to traditional combustion. Combining biodiesel and e-fuels with OFC emerges as the optimal solution for achieving net-negative emissions and advancing maritime decarbonization by 2050., This research has been partially funded by MCIN/AEI/10.13039/5 01100011033 and the European Union "NextGenerationEU"/PRTR as part of the project DIGIAMMONIA TED2021-129379A-I00 and by Grant CIPROM/2021/061 funded by Generalitat Valenciana, Spain. Additionally, the Ph.D. student Francisco Javier Garcia has also been funded by a grant from Universitat Politecnica de Valencia, Spain with reference FPI (PAID-01-22).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Extension of a Zero-Dimensional Mixing-Controlled Combustion Model for the Development of a NOx Free System Based on the Oxy-Combustion Concept

  • Serrano, J.R.|||0000-0003-0692-3917
  • López, J. Javier|||0000-0002-9486-2511
  • Martín, Jaime|||0000-0002-0496-3176
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
[EN] Oxy-combustion is a promising concept to achieve an extremely clean combustion, independently of the fuel type, because, on the one hand, it is a NOx-free combustion and, on the other hand, the CO2 produced during combustion can be easily captured once the water vapour is removed from the exhaust gases stream, consequently allowing also carbon neutral operation. An existing zero-dimensional (0D), mixing-controlled combustion model, developed for a standard diesel combustion scenario, has been adapted to the oxy-fuel combustion scenario. Initially, the model over-predicted the heat release at the end of the combustion process. The main model adaptation was to modify the relationship between the average YO2 and the effective YO2 (i.e. the one of the charge actually entrained by the spray), to be consistent with the significant increase in compression ratio needed in the oxy-fuel context. As a result, a model able to correctly predict the combustion behaviour at any operating condition has been obtained, which finally represents a very suitable tool to assist in the concept development., This research has been partly supported by Grant CIPROM/2021/061 funded by Generalitat Valenciana, by Grant PID2021-123351OB-I00 funded by MCIN/AEI/10.13039/501100011033 and, as appropriate, by 'ERDF A Way of Making Europe'. Finally it has also been partially supported by grant TED2021-129379A-I00 funded by the European Union Next generation EU/PRTR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Momentum flux-based model to estimate injection rate of an ammonia injector

  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • De La Morena, Joaquín|||0000-0003-0208-508X
  • Daniel
  • Martino, Manuel
  • Postrioti, Lucio
[EN] Ammonia emerges as a feasible candidate to replace fossil fuels to avoid in-field CO2 emissions while operating low-speed internal combustion engines. An in-depth analysis of the injection process is necessary to enable the use of this fuel. The injection rate is a fundamental characteristic of the injection process, which describes the timing and instantaneous quantity of fuel mass introduced into the combustion chamber. However, the direct experimental evaluation of the injection rate is generally not possible due to the incompatibility of ammonia with existing measurement hardware. This study proposes a methodology to estimate the ammonia injection rate curve of high-pressure injectors for compression ignition engines based on momentum flux data, obtained using equipment suitable for ammonia properties. In this regard, two single-hole injectors were investigated using ammonia and, as a reference fuel, diesel. A comparison between the injection rate and momentum flux operating on diesel allows the derivation of a transfer function for extrapolating the injection rate curve from the momentum flux signal. After validating the model, it was applied to the case of ammonia injections for which only momentum flux data were available. The proposed methodology offers a viable alternative to obtain the injection rate measurement, particularly in challenging scenarios where only momentum flux data is available and direct measurement of the injection rate is not feasible., This research has been partially funded by MCIN/AEI/10.13039/501100011033 and the European Union "NextGenerationEU"/PRTR as part of the project DIGIAMMONIA TED2021-129379A-I00. The author D. Pinilla thanks the Universitat Politecnica de Valencia for his pre-doctoral contract (FPI-2022-S2-64225) , which is included within the framework of Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-22) . Also, the authors would like to thank Jose Enrique del Rey and Omar Huerta for their valuable support during the experimental campaign.