Skip to main content

SOLUCIONES TECNOLOGICAS PARA LA IMPLANTACION DE MATERIALES SUPERCONDUCTORES EN MAQUINAS ELECTRICAS DE POTENCIA

ENE2014-52105-R

•
Funding agency name Ministerio de Economía y Competitividad
Funding agency acronym MINECO
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2014
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Management unit Secretaría de Estado de Educación, Formación Profesional y Universidades
Beneficiary centre UNIVERSIDAD DE ZARAGOZA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Enhanced quench propagation in 2G-HTS coils co-wound with stainless steel or anodised aluminium tapes

  • Núñez-Chico, A. B.
  • Martínez Fernández, Elena
  • Angurel, Luis A.
  • Navarro, Rafael
Early quench detection and thermal stability of superconducting coils are of great relevance for practical applications. Magnets made with second generation high temperature superconducting (2G-HTS) tapes present low quench propagation velocities and therefore slow voltage development and high local temperature rises, which may cause irreversible damage. Since quench propagation depends on the anisotropy of the thermal conductivity, this may be used to achieve an improvement of the thermal stability and robustness of 2G-HTS coils. On pancake type coils, the thermal conductivity along the tapes (coil's azimuthal direction) is mostly fixed by the 2G-HTS tape characteristics, so that the reduction of anisotropy relies on the improvement of the radial thermal conductivity, which depends on the used materials between superconducting tapes, as well as on the winding and impregnation processes. In this contribution, we have explored two possibilities for such anisotropy reduction: by using anodised aluminium or stainless steel tapes co-wound with the 2G-HTS tapes. For all the analysed coils, critical current distribution, minimum quench energy values and both tangential and radial quench propagation velocities at different temperatures and currents are reported and compared with the results of similar coils co-wound with polyimide (Kapton®) tapes., This work was supported by the Spanish Ministerio de Economía y Competitividad and the European FEDER Program (Projects MAT2011-22719 and ENE-2014-52105-R), and by the Gobierno de Aragón (research group T12)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Improvement of structural and superconducting properties of Bi-2212 textured rods by substituting sodium

  • Nane, O.
  • Özçelik, Bekir
  • Sotelo, Andres
  • Madre, M. A.
In this paper, the physical and superconducting properties of BiSrCaNaCuO with x=0.0, 0.05, 0.075, 0.1, and 0.20 textured superconducting fiber rods prepared by a laser floating zone (LFZ) technique were studied. The effects of Na substitution for Ca have been investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), transport measurements, dc-magnetization, magnetic hysteresis and magnetic critical current density. The powder XRD patterns of samples have indicated that Bi-2212 phase is the major one, independently of Na content. The best critical temperature, T, has been found as 93.3 K from M-T data for the sample with 0.075 Na substitution. The maximum magnetic J value has been calculated as 1.35×10 A/cm at 10 K for the 0.10 Na sample. The maximum transport critical current density has directly been measured as 1.3×10 A/cm at 77 K for the 0.05Na sample., This work is supported by Research Fund of Çukurova University, Adana, Turkey, under Grant contracts no: FBA-2015-3934. M. A. Madre and A. Sotelo wish to thank the Gobierno de Aragón and Fondo Social Europeo (Grupo de Investigacion Consolidado T12) and MINECO-FEDER (project MAT2013-46505-C3-1-R) for financial support. M. A. Madre also acknowledges funding from MINECO-FEDER (Project ENE2014-52105-R)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of Na substitution on superconducting properties of Bi-2212 ceramics prepared by Sinter-Forged process

  • Nane, O.
  • Özçelik, Bekir
  • Sotelo, Andres
  • Madre, M. A.
Bulk textured BiSrCaNaCuO (x = 0.0, 0.05, 0.075 0.1, 0.15, and 0.20) ceramics have been prepared by a polymer solution method followed by sinter-forging process. The microstructure and superconducting properties of textured samples were affected by Na substitution. According to XRD data, all samples show that Bi-2212 phase is the major one, and main peaks corresponded to the (00ℓ) diffractions confirming that the crystallographic c-axis is perpendicular to the surface. SEM micrographs showed that samples are composed of well-stacked and oriented grains. The best critical temperature, T, was measured as 85.6 K for x = 0.075. The critical current density Jc, values decrease gradually with the increase of applied magnetic field. The maximum calculated Jc was 1.38 × 10 A/cm at 10 K for 0.075 Na sample which is about four times higher than the 0.34 × 10 A/cm value determined for the pure sample. The anisotropic properties of these textured materials have been investigated using magnetic measurements., This work is supported by Research Fund of Çukurova University, Adana, Turkey, under grant contracts no: FBA-2014-3500. A. Sotelo and M.A. Madre acknowledge the Gobierno de Aragón and Fondo Social Europeo (Grupo de Investigacion Consolidado T12) and MINECO-FEDER (MAT2013-46505-C3-1-R) for financial support. M.A. Madre also acknowledges MINECO-FEDER (Project ENE2014-52105-R) for funding. Authors would like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza. This work is also supported by Research Fund of Hakkari University, Turkey, under grant contracts no: MF2014BAP1., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Modelling toolkit for simulation of maglev devices

  • Peña-Roche, Jorge
  • Badía-Majós, Antonio
arXiv:1612.09266v1, A stand-alone App has been developed, focused on obtaining information about relevant engineering properties of magnetic levitation systems. Our modelling toolkit provides real time simulations of 2D magneto-mechanical quantities for superconductor (SC)/permanent magnet structures. The source code is open and may be customised for a variety of configurations. Ultimately, it relies on the variational statement of the critical state model for the superconducting component and has been verified against experimental data for YBaCuO/NdFeB assemblies. On a quantitative basis, the values of the arising forces, induced superconducting currents, as well as a plot of the magnetic field lines are displayed upon selection of an arbitrary trajectory of the magnet in the vicinity of the SC. The stability issues related to the cooling process, as well as the maximum attainable forces for a given material and geometry are immediately observed. Due to the complexity of the problem, a strategy based on cluster computing, database compression, and real-time post-processing on the device has been implemented., Funding of this research by Spanish MINECO and FEDER programme (Project ENE2014-52105-R) and by Gobierno de Aragón (Research group T-12) is gratefully acknowledged. J Peña-Roche acknowledges a Research Grant by ICMA (PI2 programme 2015)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Dendritic flux avalanches in a superconducting MgB2 tape

  • Qureishy, T.
  • Laliena, Carlos
  • Martínez Fernández, Elena
  • Qviller, A. J.
  • Vestgården, J. I.
  • Johansen, T. H.
  • Navarro, Rafael
  • Mikheenko, P.
Tapes of MgB2 with high critical current have a significant technological potential, but can experience operational breakdown due to thermomagnetic instabilities. Such events are routinely registered by magnetisation measurements, but were never observed by direct imaging techniques. Here we report magneto-optical imaging visualisation of a tape with reduced thickness and enhanced critical current density. The spatial structure of the thermomagnetic avalanche events was resolved, and the reproducibility and nucleation thresholds were determined. Avalanches appearing at low fields are small intrusions at the tape edges, while larger fields create more extensive avalanches having dendritic structures similar to those observed in thin-film superconductors. In contrast to dendritic avalanches in thin films, the avalanches in the tapes show reproducibility to a larger extent., This work was financially supported by the University of Oslo, the Spanish Ministerio de Economía y Competitividad, the European FEDER Program (Projects MAT2011-22719 and ENE-2014-52105-R) and the Gobierno de Aragón (research group T12)., Peer reviewed