Skip to main content

FABRICACION ADITIVA DE ESTRUCTURAS CERAMICAS 3D MULTIFUNCIONALES PARA APLICACIONES TERMICAS

RTI2018-095052-B-I00

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2018
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Graphene-based nanostructures as catalysts for wet peroxide oxidation treatments: From nanopowders to 3D printed porous monoliths

  • Quintanilla, Asunción
  • Carbajo, J.
  • Casas, José A.
  • Miranzo López, Pilar
  • Osendi, María Isabel
  • Belmonte, Manuel
[EN] This paper explores the catalytic behaviour of different graphene-based nanostructures for the treatment of wastewater using Catalytic Wet Peroxide Oxidation (CWPO) processes. In a first stage, graphene-based nanopowders with distinct physical-chemical characteristics are tested in the CWPO of phenol using the following standard operating conditions: [Phenol] = 1 g·L, [HO] = 5 g L and 80 °C. Graphene nanoplatelets with the lowest oxygen content exhibit the highest catalytic activity. The typical phenol oxidation by-products are detected in the liquid phase while CO and CO appear in the gas phase. Afterwards, three dimensional (3D) porous graphene monoliths (D ∼ 11.5 mm, H ∼ 4 mm, D ∼ 0.68 mm and δ =0.36 cm, 75 cells·cm, ε = 41%) based on those nanoplatelets are additive manufactured using a direct ink writing technique and, then, tested under similar CWPO conditions. The results evidence that the 3D graphene-based structures are catalytically active, though they undergo a progressive deactivation due to the deposition of organic matter. The graphene-based monoliths can be regenerated by thermal treatments, allowing their use at industrial scale by means of reaction-thermal regeneration cycles., The authors thank the financial support by the Spanish Ministerio de Ciencia, Innovación y Universidades (MICINN) and FEDER program (EU) through the projects: CTM2016-76454-R (MICINN), MAT2015-67437-R (MICINN/ FEDER,UE) and RTI2018-095052-B-I00 (MICINN).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Synthesis and properties of Zn and Zn–Mg-doped tricalcium phosphates obtained by Spark Plasma Sintering

  • Sainz Trigo, M. Antonia
  • Serena Palomares, Sara
  • Caballero Cuesta, Ángel
[EN] β-tricalcium phosphate (Ca(PO) or TCP) are essential biomaterials because of the chemical composition, high biocompatibility and osseointegration. However, their limited mechanical properties restrict their use to areas where high mechanical performances are not required. Spark Plasma Sintering (SPS) was selected out of the unconventional sintering methods in order to obtain high-density doped-TCP bioceramic materials. The main advantages of SPS are a high heating rate, low sintering temperatures and short residence times, producing bioceramics with full density and fine-grain microstructure. The main purpose was to design, obtain by SPS and characterize undoped β-TCP, 1ZnO-doped β-TCP and 1ZnO-1MgO codoped β-TCP (wt. %) bioceramics. All the obtained samples were visually semitransparent and mainly β-TCP was detected by X-ray analysis. Densification behavior was determined by Archimedes' method and microstructural features of the sintered specimens were analyzed by Field Emission Scanning Electron Microscopy (FE-SEM-EDX). The undoped and doped β-TCP bioceramics were mechanically characterized, specifically the modulus of elasticity and Vickers microhardness. The results are compared with equivalent samples obtained by conventional solid-state sintering (CS) reaction. A first study of biological behavior was carried out, specifically direct cell adhesion of MG-63 human osteoblast-like cells on the polished surfaces of β-TCP, 1ZnO-β-TCP and 1ZnO–1MgO-β-TCP dense samples were determined. The present study concludes that the SPS process together with the doping effect enhanced sinterability, mechanical and biological properties of Zn-TCP and Zn–Mg-TCP based materials., This work is supported by the MICINN (Spain) with project CSIC 2017–60E028 and MCIU/AEI/FEDER (UE) with project RTI2018-095052-B-100.