Skip to main content

FLUENCIA Y FATIGA EN ELEMENTOS ESTRUCTURALES DE HORMIGON REFORZADO CON FIBRAS

PID2019-108978RB-C32

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Call year 2019
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publication Capítulo o parte de un libro (BookPart)

Reliability of shear strength models for fibre reinforced concrete members without shear reinforcement

  • Tošić, Nikola|||0000-0003-0242-8804
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
  • Fuente Antequera, Albert de la|||0000-0002-8016-1677
The scope and amount of fibre reinforced concrete (FRC) structural applications have seen significant increases. This means that safe and reliable ultimate limit state (ULS) models are necessary for FRC structural members. Among these, shear strength of FRC members without shear reinforcement is highly important due to the brittleness of shear failure. Because of this, the fib Model Code 2010 introduced two shear strength models: an empirical model based on Eurocode 2 and a physical model based on the Modified Compression Field Theory. However, a comprehensive reliability assessment of these models has been lacking. Therefore, in this study, the safety format of these models is assessed and the partial safety factors for FRC in shear, ¿c and ¿F are updated. As a first step, a large database of experimental results on FRC beams is used to determine model uncertainties. Following this, a comprehensive parametric probabilistic analysis is performed using the First Order Reliability Method to determine the adequate values of ¿c for different target reliability indices ß. The results of this study show that in order to reach typical reliability indices used in ULS design, ¿c and ¿F values need to be increased for FRC members without shear reinforcement for both models proposed by the fib Model Code 2010., This study has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No 836270. This support is gratefully acknowledged. The authors also wish to express their acknowledgement to the Ministry of Economy, Industry and Competitiveness of Spain for the financial support received under the scope of the projects PID2019-108978RB-C32. Any opinions, findings, conclusions, and/or recommendations in the paper are those of the authors and do not necessarily represent the views of the individuals or organizations acknowledged.
UPCommons. Portal del coneixement obert de la UPC
Publication Capítulo o parte de un libro (BookPart)

A discussion on the reliability of prEN1992-1-1:2021 shear strength provisions for fibre reinforced concrete members without shear reinforcement

  • Tošić, Nikola|||0000-0003-0242-8804
  • Bairán García, Jesús Miguel|||0000-0003-2831-1479
  • Fernández Ruíz, Miguel
  • Fuente Antequera, Albert de la|||0000-0002-8016-1677
The Eurocode 2 for the design of concrete structures (EN1992-1-1:2004) is undergoing a revision that will lead to the publication of the second generation of this code to be used across all CEN member countries. Therefore, the impact of the code will reach hundreds of millions of people. Importantly, the Eurocode 2-revision will incorporate many significant changes, amongst which is the introduction of design provisions for fibre reinforced concrete (FRC). In this regard, one of the most important aspects for ultimate limit state (ULS) design will be the consideration of the shear strength of FRC members without shear reinforcement. Such a failure mode is associated with a number of uncertainties, as well as with a potentially-brittle failure response. However, so far, the design models proposed in the Eurocode 2-revision have not been accompanied by a robust reliability-based calibration of the FRC partial factor ¿SF. Within this context, this paper presents the results of an investigation on the safety format and the partial factor ¿SF for FRC members without shear reinforcement currently provisioned in the draft for the new Eurocode 2 (prEN1992-1-1:2021). Firstly, a database of experimental results on FRC beams is used to determine the model error. On that basis, a probabilistic analysis is performed using the First Order Reliability Method (FORM) to determine adequate values of ¿SF for varying target reliability indices. The results of the study show how ¿SF values need to updated in order to reach reliability indices typically considered for ULS design. © 2023, The Author(s), under exclusive license to Springer Nature Switzerland AG., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Capítulo o parte de un libro (BookPart)

Short and long term behaviour of polypropylene fibre reinforced concrete beams with minimum steel reinforcement

  • Tošić, Nikola|||0000-0003-0242-8804
  • Fuente Antequera, Albert de la|||0000-0002-8016-1677
Fibre reinforced concrete (FRC) has quickly become an attractive solution for increasing both the mechanical performance and sustainability of concrete structures. In particular, polymeric fibres are increasingly recognized as offering significant benefits for FRC structural applications, especially in areas such as durability. Nonetheless, the behaviour of such FRC remains to be fully understood, especially from the perspective of long-term effects such as shrinkage and creep. Therefore, in this study, a comprehensive experimental programme is carried out for short- and long-term characterization of polypropylene FRC (PPFRC). The experimental program consisted of producing concretes C40/50 with 0, 3 and 9 kg/m3 of polypropylene fibres. Besides specimens for testing mechanical properties, shrinkage and creep in compression and under bending were tested. Finally, full-scale 3–m span beams with minimum steel reinforcement (0.18%) were tested until failure and under sustained loads. The results are analysed and the contribution of polypropylene fibres to reducing deflections and crack widths is assessed, with no evidence of local flexural failures due to tertiary creep phenomena. The results of this study can provide a contribution towards a fuller understanding of PPFRC structural behaviour and its future incorporation into design codes., The authors want also express their gratitude to the Spanish Ministry of Science and Innovation for the financial support received under the scope of the project CREEF (Creep and Fatigue of fibre reinforced concrete elements) (PID2019-108978RB-C32). This study has also received funding from MBCC Group. This support is gratefully acknowledged. Any opinions, findings, conclusions, and/or recommendations in the paper are those of the authors and do not necessarily represent the views of the individuals or organizations acknowledged.