Skip to main content

ESTUDIO DE LA INTERACCION CHORRO-PARED EN CONDICIONES REALISTAS DE MOTOR

TRA2015-67679-C2-1-R

•
Funding agency name Ministerio de Economía y Competitividad
Funding agency acronym MINECO
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2015
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Management unit Dirección General de Investigación Científica y Técnica
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Capítulo o parte de un libro (BookPart)

Spray/wall interaction analysis on an ECN single-hole injector at diesel-like conditions through Schlieren visualization

  • Payri, Raul|||0000-0001-7428-5510
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Peraza, Jesús
  • Bazyn, Tim
[EN] To continuously improve CFD models which simulate spray evolution, breakup and evaporation mechanisms, it is helpful to validate them with results obtained by experimental research. In the present study, a mono-orifice target nozzle from Engine Combustion Network, referred to as Spray D, was investigated at conditions of spray-wall interaction, which actually is a real situation in internal combustion engines that is not frequently analyzed by visualization. A Photron SA-X2 high-speed camera was employed to record the vapor phase development of the spray in an inert atmosphere using a Schlieren imaging single-pass setup. The experiments show that the spreading of the spray along the wall has a behavior fairly similar to penetration at free-jet situations, especially regarding to its susceptibility to the operating conditions and its proportionality to the square root of time once the spray reaches a steady regime interacting with the wall. Furthermore, the spray film thickness was measured at three distances from the spray-wall impact point during the injection event, thereby characterizing that parameter both spatially and temporally. The tests were carried out in a constant pressure-flow facility able to reproduce pressure and temperature conditions, similar to those seen into a diesel engine. In order to observe the behavior of the spray colliding with a wall within this test rig, a system capable to being fitted into it and to holding a fused quartz wall at different injector tip-wall distances and impingement angle configurations, was designed and employed., The authors would like to thank Caterpillar Inc. for their cooperation during the project, as well as the support provided by the “Ministerio de Economía y Competitividad” of the Spanish Government in the frame of the project TRA2015-67679-c2-1-R. Furthermore, the collaboration of Alberto Viera1 and Borja Hurtado in the measurements and setup of the experiment is thanked.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Capítulo o parte de un libro (BookPart)

Vapor phase penetration measurements with both single and double-pass Schlieren for the same injection event

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Viera Sotillo, Alberto Antonio
[EN] Schlieren imaging has been adopted as a standard optical technique for the analysis of diesel sprays under engine like conditions. A single-pass Schlieren arrangement is typically used for the study of single-orifice nozzles, as vessels with multiple optical accesses regularly allow line of sight visualization. Contrarily, for multi-spray nozzles, measurements are commonly performed through a single optical access, in which case a double-pass arrangement is employed. As a consequence, the light beams pass through the test section twice, increasing the optical sensitivity of the Schlieren setup. However, the impact this has on the macroscopic spray characteristics is still unclear. The scope of this study is to analyze the differences in vapor phase penetration for the same injection event, through high-speed imaging, for both single and double-pass Schlieren configurations. Experiments were carried out with a three hole nozzle with a nominal orifice diameter of 90 µm, named Spray B from the Engine Combustion Network, using commercially available diesel fuel and in non-reactive conditions. The impact of different injection pressures and chamber densities on the spray captured by each setup was assessed. On the results, vapor phase penetration followed the expected trend found in the literature, as it increases with increasing injection pressure and decreasing chamber density. Comparing the optical setups, vapor phase penetration obtained with the double-pass arrangement was marginally higher. The deviation was observed throughout all tested conditions. Although the discrepancy was approximately constant for different injection pressures and chamber temperature, it increased with increasing density. These results highlight the importance of a proper understanding regarding the limitations of optical diagnostics, in particular for results used in calibration of computational models., This research has been partially funded by FEDER and Spanish Ministerio de Economía y Competitividad through project TRA2015-67679-c2-1-R. Additionally, Alberto Viera is supported through the FPI contract 2016-S2-1361 of “Programa de Apoyo para la Investigación y Desarrollo (PAID)” of Universitat Poltècnica de València.