Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 32
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Atmospheric stability classification from floating Doppler wind lidar measurements: a machine learning approach

  • Salcedo Bosch, Andreu|||0000-0001-7398-925X
  • Silva, Marcos Paulo Aráujo da|||0000-0002-5260-8937
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
This work studies the capabilities of the k-nearest-neighbours (KNN) method to estimate the atmospheric stability from floating Doppler wind lidar measurements of the vertical wind profile. A procedure to generate synthetic wind profiles to be used as training data for the KNN is presented. The method is validated with experimental data gathered during IJmuiden campaign by a floating Doppler wind lidar against a metmast as a reference. A global hit rate of 70.2% is obtained when comparing the predicted stability classes to the reference ones., This research is part of the project PID2021-126436OB-C21 funded by Ministerio de Ciencia e Investigacion (MCIN)/ Agencia Estatal de Investigacion (AEI)/ 10.13039/501100011033/ FEDER “Una manera de hacer Europa”. The work of A. Salcedo-Bosch was supported under grant 2020 FISDU 00455 funded by Generalitat de Catalunya—AGAUR. The European Commission collaborated under projects H2020 ATMO-ACCESS (GA101008004) and H2020 ACTRIS-IMP (GA-871115)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Retrieving Monin-Obukhov dimensionless wind shear and stability from floating lidar observations

  • Silva, Marcos Paulo Aráujo da|||0000-0002-5260-8937
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
  • Salcedo Bosch, Andreu|||0000-0001-7398-925X
  • Peña Diaz, Alfredo
Floating-lidar-derived wind profiles are used to retrieve the vertical wind speed gradient, dimensionless wind shear, and dimensionless stability using Monin-Obukhov similarity theory (MOST) in the context of IJmuiden campaign. Reference retrievals are obtained by applying the same methodology to metmast-derived wind profiles. Wind gradient estimates from floating lidar measurements are successfully compared to those from the reference metmast at three different heights, yielding coefficients of determination higher than ρ 2 = 0.83. MOST flux relationships are also re-encountered when representing the dimensionless wind shear estimates as a function of dimensionless stability., This research is part of the project PID2021-126436OB-C21 funded by Ministerio de Ciencia e Investigacion (MCIN)/ Agencia Estatal de Investigacion (AEI)/ 10.13039/501100011033 y FEDER “Una manera de hacer Europa”. The work of M.P Araujo da Silva was supported under Grant PRE2018-086054 funded by MCIN/AEI/10.13039/501100011033 and FSE “El FSE invierte en tu futuro”. The work of A. Salcedo Bosch was supported under grant 2020 FISDU 00455 funded by Generalitat de Catalunya—AGAUR. The European Commission collaborated under projects H2020 ACTRIS-IMP (GA-871115) and H2020 ATMO-ACCESS (GA-101008004)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

On the use of wind profiles to assess surface boundary-layer parameters

  • Silva, Marcos Paulo Aráujo da|||0000-0002-5260-8937
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
  • Salcedo Bosch, Andreu|||0000-0001-7398-925X
  • Peña Diaz, Alfredo
Wind profiles measured at the research platform FINO1 are used to retrieve surface boundary-layer parameters, namely, the friction velocity, heat flux, and Obukhov length. The latter is used to assess atmospheric stability. Two different retrieval algorithms, the 2D parametric solver [1] and the Hybrid-Wind method [2], are compared with reference to sonic-anemometers retrievals. Regarding atmospheric stability classification, the 2D algorithm provided better performance than the Hybrid-Wind method. When comparing the 2D-estimated (HW-estimated) friction velocity to the anemometers’ reference, a determination coefficient of ρ 2 = 0.70 (ρ 2 = 0.00) were obtained., This research is part of the project PID2021-126436OB-C21 funded by Ministerio de Ciencia e Investigacion (MCIN)/ Agencia Estatal de Investigacion (AEI)/ 10.13039/501100011033 y FEDER “Una manera de hacer Europa”. The work of M.P Araujo da Silva was supported under Grant PRE2018-086054 funded by MCIN/AEI/10.13039/501100011033 and FSE “El FSE invierte en tu futuro”. The work of A. Salcedo Bosch was supported under grant 2020 FISDU 00455 funded by Generalitat de Catalunya—AGAUR. The European Commission collaborated under projects H2020 ATMO-ACCESS (GA-101008004) and H2020 ACTRISIMP (GA-871115). Data was made available by the FINO (Forschungsplattformen in Nord- und Ostsee) initiative, which was funded by the German Federal Ministry of Economic Affairs and Climate Action (BMWK) on the basis of a decision by the German Bundestag, organised by the Projekttraeger Juelich (PTJ) and coordinated by the German Federal Maritime and Hydrographic Agency (BSH)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Synergistic mixed-layer height retrieval method using microwave radiometer and lidar ceilometer observations

  • Silva, Marcos Paulo Aráujo da|||0000-0002-5260-8937
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
  • Tanamachi, Robin
  • Saeed, Umar|||0000-0003-0261-2767
This paper tackles synergistic mixed-layer height (MLH) estimation via a combination of microwave radiometer (MWR) and lidar ceilometer (LC)-based estimates. While MLH-MWR estimates rely on potential temperature retrievals, MLH-LC estimates rely on aerosol gradients. The pros and cons of MLH retrievals obtained from MWR via the parcel method and from LC via an extended Kalman filter (EKF)-based method are used to motivate the synergistic algorithm. The synergistic algorithm is introduced as a maximum-likelihood combination of MLH-MWR and MLH-LC. Two case examples from the 2013 HOPE campaign at Jülich, Germany, are used to show the robustness of the synergistic method and the effect of surface temperature measurement error. Doppler wind lidar retrievals and radiosonde reference MLH estimates are used for validation., This research is part of the projects PGC2018-094132-B-I00 and MDM-2016-0600 (“CommSensLab” Excellence Unit) funded by Ministerio de Ciencia e Investigación (MCIN)/ Agencia Estatal de Investigación (AEI)/ 10.13039/501100011033/ FEDER. Data were provided by Julich Observatory for Cloud Evolution (JOYCE-CF), a core facility funded by Deutsche Forschungsgemeinschaft via grant DFG LO 901/7-1. The work of M.P.A.S was supported under Grant PRE2018-086054 funded by MCIN/AEI/ 10.13039/501100011033 and FSE “El FSE invierte en tu futuro”. The European Commission collaborated under projects H2020 ACTRIS-IMP (GA871115) and H2020 ATMO-ACCESS (GA-101008004)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Numerical solver for vertical air motion estimation

  • Salcedo Bosch, Andreu|||0000-0001-7398-925X
  • Domínguez Pla, Paula
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
  • Frasier, Stephen J.
We present preliminary research on a method to estimate Vertical Air Motion (VAM) at a particular height by comparing the measured rain-rate (RR) by a vertically-pointing S-band Frequency-Modulated Continuous-Wave (FMCW) radar with that of a ground-based disdrometer. The method is based on a constrained parametric solver, assuming high correlation between 5-min averaged rain rates measured by the radar and disdrometer. The method is tested over disdrometer and radar observations during the Verification of the ORigins Tornado EXperiment in South East US (VORTEX-SE) project. Finally, the results are partially validated by means of fitting a gamma distribution to the VAM-corrected DSD profiles and studying its parameters., This research is part of the projects PGC2018-094132-B-I00 and MDM2016-0600 (“CommSensLab” Excellence Unit) funded by Ministerio de Ciencia e Investigación (MCIN)/ Agencia Estatal de Investigación (AEI)/10.13039/501100011033/ FEDER “Una manera de hacer Europa”. The work of A. Salcedo-Bosch was supported under grant 2020 FISDU 00455 funded by Generalitat de Catalunya—AGAUR. The European Commission collaborated under projects H2020 ACTRIS-IMP (GA-871115) and H2020 ATMOACCESS (GA-101008004)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Retrieval of planetary boundary layer height from Calipso satellite: A big data and machine learning approach

  • Salcedo Bosch, Andreu|||0000-0001-7398-925X
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
  • López Martínez, Carlos|||0000-0002-1366-9446
This study presents a Random Forest (RF) model trained on an extensive dataset to estimate the planetary boundary layer height (PBLH) retrieved from Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) on board of Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) Level 1 measurements during both daytime and nighttime. The novelty of the method lies in the RF’s capability to automatically classify the observed scenarios, enabling P BLH estimation in cloudy, multi-layer, and dust-laden conditions across diverse global regions. The RF model was trained using 10 years of CALIOP data, with radiosonde-derived P BLH retrievals coinciding with CALIPSO overpasses serving as ground truth. The results demonstrate that the RF model surpasses existing state-of-the-art methods in spatial and temporal coverage, achieving a correlation coefficient (R2 = 0.6) and root-mean-square error (RMSE) of 333.60 m, without requiring atmospheric typing, data filtering, or additional ancillary information., This research is part of the project PID2021-126436OB-C21, funded by MInisterio de Ciencia, Innovación y Universidades (MICIU)/Agencia Estatal de Investigación (AEI)/10.13039/501100011033 and ERDF/EU, and part of the PRIN 2022 PNRR, Project P20224AT3W funded by Ministero dell’Università e della Ricerca. The European Commission collaborated under projects H2020 ATMO-ACCESS (GA-101008004) and H2020 ACTRISIMP (GA-871115)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Parameterization of the inherent averaging of Doppler wind lidars: A Mann model simulator approach

  • Salcedo Bosch, Andreu|||0000-0001-7398-925X
  • Lolli, Simone
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
  • López Martínez, Carlos|||0000-0002-1366-9446
  • Mann, Jakob
  • Peña Diaz, Alfredo
This work presents a simulator approach to quantify and parametrize the inherent averaging error in wind turbulence measurements by Doppler Wind Lidars (DWL). The simulator replicates the instrumental setup of the IJmuiden campaign, which included an offshore meteorological mast with a DWL and an anemometer measuring wind at the same height as a reference (90 m a.s.l.). The Mann turbulence model was used to simulate wind turbulence boxes with a wide range of turbulence conditions, enabling the quantification of measurement errors as a function of the turbulence spectral characteristics via the Mann model parameters. The study found that only the Mann turbulence length scale (LMM) affected the DWL measurement of turbulence. Additionally, the inherent averaging error for the IJmuiden setup was parameterized using an analytical function, significantly reducing the computational effort required to retrieve it., This research is part of the project PID2021-126436OB-C21, funded by MInisterio de Ciencia, Innovación y Universidades (MICIU)/Agencia Estatal de Investigación (AEI)/10.13039/501100011033 and ERDF/EU, and part of the PRIN 2022 PNRR, Project P20224AT3W funded by Ministero dell’Università e della Ricerca. The European Commission collaborated under projects H2020 ATMO-ACCESS (GA-101008004) and H2020 ACTRISIMP (GA-871115)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Analytical-model compensation of the motion-induced turbulence in floating Doppler-wind Lidar measurements

  • Salcedo Bosch, Andreu|||0000-0001-7398-925X
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
This work presents a novel method to statistically compensate for the apparent motion-induced turbulence in floating Doppler-Wind LiDAR measurements. The method relies on the analytical model [1], recently published by the authors, applied to the ZephIR T M 300 continuous-wave LiDAR. Performance of the method is studied over two floating LiDAR measurement sites/configurations, a mild near-offshore Mediterranean site and an open-sea site (IJmuiden, North Sea), and compared to fixed LiDAR measurements as a reference. The method outperforms other motion compensation approaches based on turbulence increment estimation with less computational effort., This research is part of the project PID2021-126436OB-C21 funded by Ministerio de Ciencia e Investigación (MCIN)/ Agencia Estatal de Investigacion (AEI)/ 10.13039/501100011033 y FEDER “Una manera de hacer Europa”. The work of A. Salcedo-Bosch was supported under grant 2020 FISDU 00455 funded by Generalitat de Catalunya—AGAUR. The European Commission collaborated under projects H2020 ATMO-ACCESS (GA101008004) and H2020 ACTRIS-IMP (GA-871115)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

On the feasibility of radial spatial averaging to improve satellite Synthetic Aperture Radar ocean wind retrievals

  • Salcedo Bosch, Andreu|||0000-0001-7398-925X
  • Lolli, Simone
  • Escalera i Mendo, Aina
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
  • López Martínez, Carlos|||0000-0002-1366-9446
This work focuses on the feasibility of radial spatial av-eraging to improve satellite Synthetic Aperture Radar (SAR) ocean Horizontal Wind Speed (HWS) retrievals even in neu-tral atmosphere situations. The reference for comparison are in-situ HWS measurements from the FINO-1 offshore metmast. The data used from the Sentinel-1 SAR are the Level 2 Ocean (OCN) products for wind, wave, and current applications, retrieving the information from the Ocean Wind Field (OWI) component through Geophysical Model Func-tion (GMF) CMOD-IFR2. The GMF allows for estimation of the equivalent wind speed at 10 meters and, therefore, stable and convective regimes can bias the estimations. The best agreement between SAR and FINO-1 was found -as expected- for neutral atmospheres, which yielded a determi-nation coefficient of R2 = 0.90 and a root mean squared error (RMSE) of 1.2 m/s. In non-neutral scenarios, statisti-cal indicators showed that fine-tuned spatial averaging is also able to improve SAR HWS retrievals and yielded comparable statistical indicators (R2 = 0.87, RMSE = 1.1 m/s) for the HWS estimates., This research is part of the project PID2021-126436OB-C21 funded by Ministerio de Ciencia e Investigación (MCIN)/ Agencia Estatal de Investigación (AEI)/ 10.13039/501100011033 y FEDER “Una manera de hacer Europa” and part of the PRIN 2022 PNRR, Project P20224AT3W funded by Ministero dell’Universita e della Ricerca. The European Commission collaborated under projects H2020 ATMO-ACCESS (GA-101008004) and H2020 ACTRIS-IMP (GA-871115)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Floating lidar assessment of atmospheric stability in the North Sea

  • Silva, Marcos Paulo Aráujo da|||0000-0002-5260-8937
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
  • Farré Guarné, Joan
  • Salcedo Bosch, Andreu|||0000-0001-7398-925X
  • González Marco, Daniel|||0000-0002-9619-1897
  • Peña Diaz, Alfredo
In this work, the 2D parametric-solver algorithm [1] used to assess atmospheric stability from floating Doppler wind lidar (FDWL) measurements is revisited. The algorithm performance is studied using data from IJmuiden campaign. Mast-measured temperature and wind-speed provided the reference parameters used to evaluate the performance of the stability estimation algorithm. From 5,922 10-min samples available, the algorithm classified the atmosphere as stable (52% of the cases), neutral (31%) and unstable (17%), which successfully agreed with the mast-derived reference classification (53%, 30% and 17%, respectively)., This research is part of the projects PGC2018-094132-B-I00 and MDM2016-0600 (“CommSensLab” Excellence Unit) funded by Ministerio de Ciencia e Investigación (MCIN)/ Agencia Estatal de Investigación (AEI)/10.13039/501100011033/ FEDER “Una manera de hacer Europa”. The work of M.P Araujo da Silva was supported under Grant PRE2018-086054 funded by MCIN/AEI/10.13039/501100011033 and FSE “El FSE invierte en tu futuro”. The work of A. Salcedo-Bosch was supported under grant 2020 FISDU 00455 funded by Generalitat de Catalunya—AGAUR. The European Commission collaborated under projects H2020 ACTRIS-IMP (GA-871115) and H2020 ATMO-ACCESS (GA-101008004)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Variance processing for stable boundary-layer height estimation using backscatter lidar data: A discussion

  • Muñoz Porcar, Constantino|||0000-0002-6543-119X
  • Silva, Marcos Paulo Aráujo da|||0000-0002-5260-8937
  • Saeed, Umar|||0000-0003-0261-2767
  • Rey Micolau, Francesc|||0000-0003-3615-7627
  • Pay Pérez, M. Teresa
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
In this paper we present a method for estimating the height of the nocturnal stable boundary layer by using lidar measurements and a single radiosonde for unambiguous initial guess. The method relies on the correlation between aerosol stratifications in the stable boundary layer and minimum variance levels in the attenuated backscatter profile. The method is based on calculating either temporal or spatial variance vertical profiles of the attenuated backscatter and threshold-limited decision. A radiosonde temperature-based estimation is used to provide an initial guess if several minimum variance regions are detected. Two study cases using ceilometer data are shown. Comparison with temperature-based estimations from a collocated microwave radiometer have been used for validation. The method can be useful for estimating the stable boundary layer height in sites with a ceilometer but without any available temperature profiler., This work was supported via Spanish Government–European Regional Development Funds project PGC2018-094132-B-I00 and EU H2020 ACTRIS-IMP (GA 871115). CommSensLab is a María-de-Maeztu Unit of Excellence funded by the Agencia Estatal de Investigación, Spain. The work of M.P. Araujo da Silva was supported by the Spanish Ministry of Science, Innovation and Universities under Grant PRE2018-086054. Data were provided by Jülich Observatory for Cloud Evolution (JOYCE-CF), a core facility funded by Deutsche Forschungsgemeinschaft via grant DFG LO 901/7-1., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Analysis of atmospheric aerosol properties using lidar measurements and their impact on radiative budget in Barcelona over the past 20 years

  • Lolli, Simone
  • Sicard, Michaël|||0000-0001-8287-9693
  • Comerón Tejero, Adolfo|||0000-0001-6886-3679
  • Gil Díaz, Cristina
  • Oliveira, Daniel Camilo Fortunato dos Santos|||0000-0001-7461-7765
  • Landi, Tony C.
  • Rodríguez Gómez, Alejandro Antonio|||0000-0002-9209-0685
  • Muñoz Porcar, Constantino|||0000-0002-6543-119X
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
  • Dios Otín, Víctor Federico|||0000-0002-6720-8514
Aerosols are significant atmospheric constituents that modulate radiation and cloud processes. We evaluated 17-year aerosol profile trends in Barcelona, Spain, from lidar measurements. In summer aerosol reaches 5 km, while in the other seasons it exhibits clear exponential decay. Sahara dust transport affects all seasons, with winter layers above and others penetrating the boundary layer. This study informs the formation of haze and urban preservation strategies in the Mediterranean. The analysis puts in evidence that the averaged net radiative effect is of cooling at both surface level and top of the atmosphere., This work has been made possible through the efforts of many people, whom it would be too long to mention, and the funding of many grants through the years, in particular European projects of different framework programmes (FP5 EARLINET project (ID EVR1-CT-1999-40003), FP6 EARLINET-ASOS (ID: 25991), FP7 ACTRIS (ID: 262254), H2020 ACTRIS-2 (ID: 654109), ACTRIS-PPP (ID: 739530), ACTRIS IMP (ID: 871115) and ATMO-ACCESS (ID: 101008004)), projects of the Spanish National Research Programmes (refs. TIC 431/93, AMB96-1144-C02-01, REN2000-1907-CE, REN2000-1754-C02-02 / CLI, REN2003-09753-C02-C02 / CLI, REN2003-09753-C02-C CGL2008- 01330-E/CLI 02 / CLI, REN2002-12784-E, CGL2005-5131-E, CGL2006-27108-E/CLI, CGL2006-26149-E/CLI, CGL2007-28871-/CLI, CTM2006-27154-E/TECNO, TEC2006-07850/TCM, TEC2009-09106, TEC2012-34575, TEC2015-63832-P and PID2019-103886RB-I00), the project of the Catalan Regional Government IMMPACTE, and the ESA project No. nº 21487/08/NL/HE. The support of the European Union through NextGenerationEU funds is also gratefully acknowledged., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Use of pure rotational Raman channels for lidar measurement of aerosol extinction coefficient: the EARLINET/ACTRIS Barcelona station experience

  • Rodríguez Gómez, Alejandro Antonio|||0000-0002-9209-0685
  • Muñoz Porcar, Constantino|||0000-0002-6543-119X
  • Zenteno Hernández, José Alex
  • Comerón Tejero, Adolfo|||0000-0001-6886-3679
  • Dios Otín, Víctor Federico|||0000-0002-6720-8514
  • Sicard, Michaël|||0000-0001-8287-9693
  • Gil Díaz, Cristina
  • Oliveira, Daniel Camilo Fortunato dos Santos|||0000-0001-7461-7765
  • Mandal, Charly
Advances in interference filter technology permit currently using selected parts of the N2 and O2 pure rotational Raman spectra with very low temperature sensitivity, while rejecting sufficiently the elastic return. The Raman technique to retrieve the aerosol extinction coefficient can then be used with higher signal-to-noise ratios, because of a higher (about 8 times) effective differential backscatter cross-section as compared to the cross-section of the N2 vibro-rotational spectra. The design and results of pure rotational Raman channels at 354 nm and 530 nm allowing daytime aerosol extinction measurements implemented at the EARLINET/ACTRIS Barcelona lidar station are presented and discussed. © 2022 SPIE., The authors acknowledge the funding of this research by the Spanish Ministry for Science and Innovation for the project PID2019-103886RB-I00 and its support to ACTRIS ERIC. The authors also acknowledge the support of the European Commission through the Horizon 2020 Research and Innovation Framework Programme projects ACTRIS IMP (grant agreement No 871115) and ATMO-ACCESS (grant agreement No 101008004), Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

On the performance of the unscented Kalman filter for floating Doppler wind lidar motion correction in an open-sea scenario

  • Salcedo Bosch, Andreu|||0000-0001-7398-925X
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
This work analyzes the influence of open-sea wave motion on the performance of the floating Doppler wind lidar motion-compensation method [1], recently published by the authors. The method is applied to a floating ZephIR 300 LiDAR and compared to a fixed LiDAR as a reference. The motion-correction results are studied as a function of the wave-motion intensity by clustering the IJmuiden experimental campaign into three categories: low, medium, and high motion., This research is part of the project PID2021-126436OB-C21 funded by Ministerio de Ciencia e Investigacion (MCIN)/ Agencia Estatal de Investigacion (AEI)/ 10.13039/501100011033 y FEDER “Una manera de hacer Europa”. The work of A. Salcedo-Bosch was supported under grant 2020 FISDU 00455 funded by Generalitat de Catalunya—AGAUR. The European Commission collaborated under projects H2020 ATMO-ACCESS (GA101008004) and H2020 ACTRIS-IMP (GA-871115)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

On adaptive unscented Kalman filtering for floating Doppler wind-lidar motion correction: Effect of the number of lidar measurement heights

  • Salcedo Bosch, Andreu|||0000-0001-7398-925X
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
  • Sospedra Iglesias, Joaquim|||0000-0003-4207-7922
This work studies the influence of the number of lidar measurement heights on the performance of the floating Doppler wind lidar motion-correction algorithm, recently published by the authors. The work is in the context of offshore wind energy and continuous-wave focusable ZephirTM 300 lidar. A downsampling technique applied over the lidar-measured wind speed time-series is used to simulate different height-sounding configurations. The operation of the filter under one, three, and five measurement heights of the lidar is studied by using data from El Pont del Petroli measurement campaign. The filter is proved to remove apparent turbulence addition in all three cases, showing a deterioration of statistical indicators as the number of sounding heights increase., This research was funded by the Spanish Government and EU Regional Development Funds, ARS project PGC2018-094132-B-I00, H2020 ACTRIS-IMP project GA-871115 and H2020 ATMO-ACCESS project GA101008004. The European Institute of Innovation and Technology (EIT), KIC InnoEnergy project NEPTUNE (call FP7) supported the measurement campaigns. The Generalitat de Catalunya—AGAUR funded doctoral grant 2020 FISDU 00455 by A. Salcedo-Bosch. CommSensLab-UPC is an Excellence Unit (MDM-2016-0600) funded by the Agencia Estatal de Investigacion, Spain., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Floating Doppler Wind Lidar motion simulator for horizontal wind speed measurement error assessment

  • Salcedo Bosch, Andreu|||0000-0001-7398-925X
  • Farré Guarné, Joan
  • Sala Álvarez, José|||0000-0002-6879-1991
  • Villares Piera, Nemesio Javier|||0000-0001-5701-9819
  • Tanamachi, Robin
  • Rocadenbosch Burillo, Francisco|||0000-0001-8614-4408
This study presents a wind retrieval simulator of a floating Doppler Wind Lidar (DWL) with 6 Degrees of Freedom (DoF) motion. The simulator considers a continuous-wave conical-scanning floating DWL which retrieves the wind vector from 50 radial velocities per scan. The 6 DoF motion framework as well as the most important buoy motion equations are summarized. Rotational and translational motion effects over HWS measurements are studied parametrically., This work was supported via Spanish Government–European Regional Development Funds project PGC2018-094132-B-I00 and H2020 ACTRIS- IMP (GA-871115). The European Institute of Innovation and Technology (EIT), KIC InnoEnergy project NEPTUNE (Offshore Metocean Data Measuring Equipment and Wind, Wave and Current Analysis and Forecasting Software, call FP7) supported measurements campaigns. CommSensLab is a María-de-Maeztu Unit of Excellence funded by the Agencia Estatal de Investigación (Spanish National Science Foundation). The work of Andreu Salcedo was supported by the “Agència de Gestió d’Adjuts Universitaris i de la Recerca (AGAUR)”, Generalitat de Catalunya, under Grant no. 2020 FISDU 00455., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Parameterization of the inherent averaging of Doppler wind lidars: A Mann model simulator approach

  • Salcedo Bosch, Andreu
  • Lolli, Simone
  • Rocadenbosch Burillo, Francisco
  • López Martínez, Carlos
  • Mann, Jakob
  • Peña Diaz, Alfredo
This work presents a simulator approach to quantify and parametrize the inherent averaging error in wind turbulence measurements by Doppler Wind Lidars (DWL). The simulator replicates the instrumental setup of the IJmuiden campaign, which included an offshore meteorological mast with a DWL and an anemometer measuring wind at the same height as a reference (90 m a.s.l.). The Mann turbulence model was used to simulate wind turbulence boxes with a wide range of turbulence conditions, enabling the quantification of measurement errors as a function of the turbulence spectral characteristics via the Mann model parameters. The study found that only the Mann turbulence length scale (LMM) affected the DWL measurement of turbulence. Additionally, the inherent averaging error for the IJmuiden setup was parameterized using an analytical function, significantly reducing the computational effort required to retrieve it., This research is part of the project PID2021-126436OB-C21, funded by MInisterio de Ciencia, Innovación y Universidades (MICIU)/Agencia Estatal de Investigación (AEI)/10.13039/501100011033 and ERDF/EU, and part of the PRIN 2022 PNRR, Project P20224AT3W funded by Ministero dell’Università e della Ricerca. The European Commission collaborated under projects H2020 ATMO-ACCESS (GA-101008004) and H2020 ACTRISIMP (GA-871115)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Atmospheric stability classification from floating Doppler wind lidar measurements: a machine learning approach

  • Salcedo Bosch, Andreu
  • Silva, Marcos Paulo Aráujo da
  • Rocadenbosch Burillo, Francisco
This work studies the capabilities of the k-nearest-neighbours (KNN) method to estimate the atmospheric stability from floating Doppler wind lidar measurements of the vertical wind profile. A procedure to generate synthetic wind profiles to be used as training data for the KNN is presented. The method is validated with experimental data gathered during IJmuiden campaign by a floating Doppler wind lidar against a metmast as a reference. A global hit rate of 70.2% is obtained when comparing the predicted stability classes to the reference ones., This research is part of the project PID2021-126436OB-C21 funded by Ministerio de Ciencia e Investigacion (MCIN)/ Agencia Estatal de Investigacion (AEI)/ 10.13039/501100011033/ FEDER “Una manera de hacer Europa”. The work of A. Salcedo-Bosch was supported under grant 2020 FISDU 00455 funded by Generalitat de Catalunya—AGAUR. The European Commission collaborated under projects H2020 ATMO-ACCESS (GA101008004) and H2020 ACTRIS-IMP (GA-871115)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

On the feasibility of radial spatial averaging to improve satellite Synthetic Aperture Radar ocean wind retrievals

  • Salcedo Bosch, Andreu
  • Lolli, Simone
  • Escalera i Mendo, Aina
  • Rocadenbosch Burillo, Francisco
  • López Martínez, Carlos
This work focuses on the feasibility of radial spatial av-eraging to improve satellite Synthetic Aperture Radar (SAR) ocean Horizontal Wind Speed (HWS) retrievals even in neu-tral atmosphere situations. The reference for comparison are in-situ HWS measurements from the FINO-1 offshore metmast. The data used from the Sentinel-1 SAR are the Level 2 Ocean (OCN) products for wind, wave, and current applications, retrieving the information from the Ocean Wind Field (OWI) component through Geophysical Model Func-tion (GMF) CMOD-IFR2. The GMF allows for estimation of the equivalent wind speed at 10 meters and, therefore, stable and convective regimes can bias the estimations. The best agreement between SAR and FINO-1 was found -as expected- for neutral atmospheres, which yielded a determi-nation coefficient of R2 = 0.90 and a root mean squared error (RMSE) of 1.2 m/s. In non-neutral scenarios, statisti-cal indicators showed that fine-tuned spatial averaging is also able to improve SAR HWS retrievals and yielded comparable statistical indicators (R2 = 0.87, RMSE = 1.1 m/s) for the HWS estimates., This research is part of the project PID2021-126436OB-C21 funded by Ministerio de Ciencia e Investigación (MCIN)/ Agencia Estatal de Investigación (AEI)/ 10.13039/501100011033 y FEDER “Una manera de hacer Europa” and part of the PRIN 2022 PNRR, Project P20224AT3W funded by Ministero dell’Universita e della Ricerca. The European Commission collaborated under projects H2020 ATMO-ACCESS (GA-101008004) and H2020 ACTRIS-IMP (GA-871115)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Analytical-model compensation of the motion-induced turbulence in floating Doppler-wind Lidar measurements

  • Salcedo Bosch, Andreu
  • Rocadenbosch Burillo, Francisco
This work presents a novel method to statistically compensate for the apparent motion-induced turbulence in floating Doppler-Wind LiDAR measurements. The method relies on the analytical model [1], recently published by the authors, applied to the ZephIR T M 300 continuous-wave LiDAR. Performance of the method is studied over two floating LiDAR measurement sites/configurations, a mild near-offshore Mediterranean site and an open-sea site (IJmuiden, North Sea), and compared to fixed LiDAR measurements as a reference. The method outperforms other motion compensation approaches based on turbulence increment estimation with less computational effort., This research is part of the project PID2021-126436OB-C21 funded by Ministerio de Ciencia e Investigación (MCIN)/ Agencia Estatal de Investigacion (AEI)/ 10.13039/501100011033 y FEDER “Una manera de hacer Europa”. The work of A. Salcedo-Bosch was supported under grant 2020 FISDU 00455 funded by Generalitat de Catalunya—AGAUR. The European Commission collaborated under projects H2020 ATMO-ACCESS (GA101008004) and H2020 ACTRIS-IMP (GA-871115)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

On adaptive unscented Kalman filtering for floating Doppler wind-lidar motion correction: Effect of the number of lidar measurement heights

  • Salcedo Bosch, Andreu
  • Rocadenbosch Burillo, Francisco
  • Sospedra Iglesias, Joaquim
This work studies the influence of the number of lidar measurement heights on the performance of the floating Doppler wind lidar motion-correction algorithm, recently published by the authors. The work is in the context of offshore wind energy and continuous-wave focusable ZephirTM 300 lidar. A downsampling technique applied over the lidar-measured wind speed time-series is used to simulate different height-sounding configurations. The operation of the filter under one, three, and five measurement heights of the lidar is studied by using data from El Pont del Petroli measurement campaign. The filter is proved to remove apparent turbulence addition in all three cases, showing a deterioration of statistical indicators as the number of sounding heights increase., This research was funded by the Spanish Government and EU Regional Development Funds, ARS project PGC2018-094132-B-I00, H2020 ACTRIS-IMP project GA-871115 and H2020 ATMO-ACCESS project GA101008004. The European Institute of Innovation and Technology (EIT), KIC InnoEnergy project NEPTUNE (call FP7) supported the measurement campaigns. The Generalitat de Catalunya—AGAUR funded doctoral grant 2020 FISDU 00455 by A. Salcedo-Bosch. CommSensLab-UPC is an Excellence Unit (MDM-2016-0600) funded by the Agencia Estatal de Investigacion, Spain., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Retrieving Monin-Obukhov dimensionless wind shear and stability from floating lidar observations

  • Silva, Marcos Paulo Aráujo da
  • Rocadenbosch Burillo, Francisco
  • Salcedo Bosch, Andreu
  • Peña Diaz, Alfredo
Floating-lidar-derived wind profiles are used to retrieve the vertical wind speed gradient, dimensionless wind shear, and dimensionless stability using Monin-Obukhov similarity theory (MOST) in the context of IJmuiden campaign. Reference retrievals are obtained by applying the same methodology to metmast-derived wind profiles. Wind gradient estimates from floating lidar measurements are successfully compared to those from the reference metmast at three different heights, yielding coefficients of determination higher than ρ 2 = 0.83. MOST flux relationships are also re-encountered when representing the dimensionless wind shear estimates as a function of dimensionless stability., This research is part of the project PID2021-126436OB-C21 funded by Ministerio de Ciencia e Investigacion (MCIN)/ Agencia Estatal de Investigacion (AEI)/ 10.13039/501100011033 y FEDER “Una manera de hacer Europa”. The work of M.P Araujo da Silva was supported under Grant PRE2018-086054 funded by MCIN/AEI/10.13039/501100011033 and FSE “El FSE invierte en tu futuro”. The work of A. Salcedo Bosch was supported under grant 2020 FISDU 00455 funded by Generalitat de Catalunya—AGAUR. The European Commission collaborated under projects H2020 ACTRIS-IMP (GA-871115) and H2020 ATMO-ACCESS (GA-101008004)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Retrieval of planetary boundary layer height from Calipso satellite: A big data and machine learning approach

  • Salcedo Bosch, Andreu
  • Rocadenbosch Burillo, Francisco
  • López Martínez, Carlos
This study presents a Random Forest (RF) model trained on an extensive dataset to estimate the planetary boundary layer height (PBLH) retrieved from Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) on board of Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) Level 1 measurements during both daytime and nighttime. The novelty of the method lies in the RF’s capability to automatically classify the observed scenarios, enabling P BLH estimation in cloudy, multi-layer, and dust-laden conditions across diverse global regions. The RF model was trained using 10 years of CALIOP data, with radiosonde-derived P BLH retrievals coinciding with CALIPSO overpasses serving as ground truth. The results demonstrate that the RF model surpasses existing state-of-the-art methods in spatial and temporal coverage, achieving a correlation coefficient (R2 = 0.6) and root-mean-square error (RMSE) of 333.60 m, without requiring atmospheric typing, data filtering, or additional ancillary information., This research is part of the project PID2021-126436OB-C21, funded by MInisterio de Ciencia, Innovación y Universidades (MICIU)/Agencia Estatal de Investigación (AEI)/10.13039/501100011033 and ERDF/EU, and part of the PRIN 2022 PNRR, Project P20224AT3W funded by Ministero dell’Università e della Ricerca. The European Commission collaborated under projects H2020 ATMO-ACCESS (GA-101008004) and H2020 ACTRISIMP (GA-871115)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Synergistic mixed-layer height retrieval method using microwave radiometer and lidar ceilometer observations

  • Silva, Marcos Paulo Aráujo da
  • Rocadenbosch Burillo, Francisco
  • Tanamachi, Robin
  • Saeed, Umar
This paper tackles synergistic mixed-layer height (MLH) estimation via a combination of microwave radiometer (MWR) and lidar ceilometer (LC)-based estimates. While MLH-MWR estimates rely on potential temperature retrievals, MLH-LC estimates rely on aerosol gradients. The pros and cons of MLH retrievals obtained from MWR via the parcel method and from LC via an extended Kalman filter (EKF)-based method are used to motivate the synergistic algorithm. The synergistic algorithm is introduced as a maximum-likelihood combination of MLH-MWR and MLH-LC. Two case examples from the 2013 HOPE campaign at Jülich, Germany, are used to show the robustness of the synergistic method and the effect of surface temperature measurement error. Doppler wind lidar retrievals and radiosonde reference MLH estimates are used for validation., This research is part of the projects PGC2018-094132-B-I00 and MDM-2016-0600 (“CommSensLab” Excellence Unit) funded by Ministerio de Ciencia e Investigación (MCIN)/ Agencia Estatal de Investigación (AEI)/ 10.13039/501100011033/ FEDER. Data were provided by Julich Observatory for Cloud Evolution (JOYCE-CF), a core facility funded by Deutsche Forschungsgemeinschaft via grant DFG LO 901/7-1. The work of M.P.A.S was supported under Grant PRE2018-086054 funded by MCIN/AEI/ 10.13039/501100011033 and FSE “El FSE invierte en tu futuro”. The European Commission collaborated under projects H2020 ACTRIS-IMP (GA871115) and H2020 ATMO-ACCESS (GA-101008004)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Variance processing for stable boundary-layer height estimation using backscatter lidar data: A discussion

  • Muñoz Porcar, Constantino
  • Silva, Marcos Paulo Aráujo da
  • Saeed, Umar
  • Rey Micolau, Francesc
  • Pay Pérez, M. Teresa
  • Rocadenbosch Burillo, Francisco
In this paper we present a method for estimating the height of the nocturnal stable boundary layer by using lidar measurements and a single radiosonde for unambiguous initial guess. The method relies on the correlation between aerosol stratifications in the stable boundary layer and minimum variance levels in the attenuated backscatter profile. The method is based on calculating either temporal or spatial variance vertical profiles of the attenuated backscatter and threshold-limited decision. A radiosonde temperature-based estimation is used to provide an initial guess if several minimum variance regions are detected. Two study cases using ceilometer data are shown. Comparison with temperature-based estimations from a collocated microwave radiometer have been used for validation. The method can be useful for estimating the stable boundary layer height in sites with a ceilometer but without any available temperature profiler., This work was supported via Spanish Government–European Regional Development Funds project PGC2018-094132-B-I00 and EU H2020 ACTRIS-IMP (GA 871115). CommSensLab is a María-de-Maeztu Unit of Excellence funded by the Agencia Estatal de Investigación, Spain. The work of M.P. Araujo da Silva was supported by the Spanish Ministry of Science, Innovation and Universities under Grant PRE2018-086054. Data were provided by Jülich Observatory for Cloud Evolution (JOYCE-CF), a core facility funded by Deutsche Forschungsgemeinschaft via grant DFG LO 901/7-1., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Numerical solver for vertical air motion estimation

  • Salcedo Bosch, Andreu
  • Domínguez Pla, Paula
  • Rocadenbosch Burillo, Francisco
  • Frasier, Stephen J.
We present preliminary research on a method to estimate Vertical Air Motion (VAM) at a particular height by comparing the measured rain-rate (RR) by a vertically-pointing S-band Frequency-Modulated Continuous-Wave (FMCW) radar with that of a ground-based disdrometer. The method is based on a constrained parametric solver, assuming high correlation between 5-min averaged rain rates measured by the radar and disdrometer. The method is tested over disdrometer and radar observations during the Verification of the ORigins Tornado EXperiment in South East US (VORTEX-SE) project. Finally, the results are partially validated by means of fitting a gamma distribution to the VAM-corrected DSD profiles and studying its parameters., This research is part of the projects PGC2018-094132-B-I00 and MDM2016-0600 (“CommSensLab” Excellence Unit) funded by Ministerio de Ciencia e Investigación (MCIN)/ Agencia Estatal de Investigación (AEI)/10.13039/501100011033/ FEDER “Una manera de hacer Europa”. The work of A. Salcedo-Bosch was supported under grant 2020 FISDU 00455 funded by Generalitat de Catalunya—AGAUR. The European Commission collaborated under projects H2020 ACTRIS-IMP (GA-871115) and H2020 ATMOACCESS (GA-101008004)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

On the use of wind profiles to assess surface boundary-layer parameters

  • Silva, Marcos Paulo Aráujo da
  • Rocadenbosch Burillo, Francisco
  • Salcedo Bosch, Andreu
  • Peña Diaz, Alfredo
Wind profiles measured at the research platform FINO1 are used to retrieve surface boundary-layer parameters, namely, the friction velocity, heat flux, and Obukhov length. The latter is used to assess atmospheric stability. Two different retrieval algorithms, the 2D parametric solver [1] and the Hybrid-Wind method [2], are compared with reference to sonic-anemometers retrievals. Regarding atmospheric stability classification, the 2D algorithm provided better performance than the Hybrid-Wind method. When comparing the 2D-estimated (HW-estimated) friction velocity to the anemometers’ reference, a determination coefficient of ρ 2 = 0.70 (ρ 2 = 0.00) were obtained., This research is part of the project PID2021-126436OB-C21 funded by Ministerio de Ciencia e Investigacion (MCIN)/ Agencia Estatal de Investigacion (AEI)/ 10.13039/501100011033 y FEDER “Una manera de hacer Europa”. The work of M.P Araujo da Silva was supported under Grant PRE2018-086054 funded by MCIN/AEI/10.13039/501100011033 and FSE “El FSE invierte en tu futuro”. The work of A. Salcedo Bosch was supported under grant 2020 FISDU 00455 funded by Generalitat de Catalunya—AGAUR. The European Commission collaborated under projects H2020 ATMO-ACCESS (GA-101008004) and H2020 ACTRISIMP (GA-871115). Data was made available by the FINO (Forschungsplattformen in Nord- und Ostsee) initiative, which was funded by the German Federal Ministry of Economic Affairs and Climate Action (BMWK) on the basis of a decision by the German Bundestag, organised by the Projekttraeger Juelich (PTJ) and coordinated by the German Federal Maritime and Hydrographic Agency (BSH)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

On the performance of the unscented Kalman filter for floating Doppler wind lidar motion correction in an open-sea scenario

  • Salcedo Bosch, Andreu
  • Rocadenbosch Burillo, Francisco
This work analyzes the influence of open-sea wave motion on the performance of the floating Doppler wind lidar motion-compensation method [1], recently published by the authors. The method is applied to a floating ZephIR 300 LiDAR and compared to a fixed LiDAR as a reference. The motion-correction results are studied as a function of the wave-motion intensity by clustering the IJmuiden experimental campaign into three categories: low, medium, and high motion., This research is part of the project PID2021-126436OB-C21 funded by Ministerio de Ciencia e Investigacion (MCIN)/ Agencia Estatal de Investigacion (AEI)/ 10.13039/501100011033 y FEDER “Una manera de hacer Europa”. The work of A. Salcedo-Bosch was supported under grant 2020 FISDU 00455 funded by Generalitat de Catalunya—AGAUR. The European Commission collaborated under projects H2020 ATMO-ACCESS (GA101008004) and H2020 ACTRIS-IMP (GA-871115)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Floating lidar assessment of atmospheric stability in the North Sea

  • Silva, Marcos Paulo Aráujo da
  • Rocadenbosch Burillo, Francisco
  • Farré Guarné, Joan
  • Salcedo Bosch, Andreu
  • González Marco, Daniel
  • Peña Diaz, Alfredo
In this work, the 2D parametric-solver algorithm [1] used to assess atmospheric stability from floating Doppler wind lidar (FDWL) measurements is revisited. The algorithm performance is studied using data from IJmuiden campaign. Mast-measured temperature and wind-speed provided the reference parameters used to evaluate the performance of the stability estimation algorithm. From 5,922 10-min samples available, the algorithm classified the atmosphere as stable (52% of the cases), neutral (31%) and unstable (17%), which successfully agreed with the mast-derived reference classification (53%, 30% and 17%, respectively)., This research is part of the projects PGC2018-094132-B-I00 and MDM2016-0600 (“CommSensLab” Excellence Unit) funded by Ministerio de Ciencia e Investigación (MCIN)/ Agencia Estatal de Investigación (AEI)/10.13039/501100011033/ FEDER “Una manera de hacer Europa”. The work of M.P Araujo da Silva was supported under Grant PRE2018-086054 funded by MCIN/AEI/10.13039/501100011033 and FSE “El FSE invierte en tu futuro”. The work of A. Salcedo-Bosch was supported under grant 2020 FISDU 00455 funded by Generalitat de Catalunya—AGAUR. The European Commission collaborated under projects H2020 ACTRIS-IMP (GA-871115) and H2020 ATMO-ACCESS (GA-101008004)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Use of pure rotational Raman channels for lidar measurement of aerosol extinction coefficient: the EARLINET/ACTRIS Barcelona station experience

  • Rodríguez Gómez, Alejandro Antonio
  • Muñoz Porcar, Constantino
  • Zenteno Hernández, José Alex
  • Comerón Tejero, Adolfo
  • Dios Otín, Víctor Federico
  • Sicard, Michaël
  • Gil Díaz, Cristina
  • Oliveira, Daniel Camilo Fortunato dos Santos
  • Mandal, Charly
Advances in interference filter technology permit currently using selected parts of the N2 and O2 pure rotational Raman spectra with very low temperature sensitivity, while rejecting sufficiently the elastic return. The Raman technique to retrieve the aerosol extinction coefficient can then be used with higher signal-to-noise ratios, because of a higher (about 8 times) effective differential backscatter cross-section as compared to the cross-section of the N2 vibro-rotational spectra. The design and results of pure rotational Raman channels at 354 nm and 530 nm allowing daytime aerosol extinction measurements implemented at the EARLINET/ACTRIS Barcelona lidar station are presented and discussed. © 2022 SPIE., The authors acknowledge the funding of this research by the Spanish Ministry for Science and Innovation for the project PID2019-103886RB-I00 and its support to ACTRIS ERIC. The authors also acknowledge the support of the European Commission through the Horizon 2020 Research and Innovation Framework Programme projects ACTRIS IMP (grant agreement No 871115) and ATMO-ACCESS (grant agreement No 101008004), Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Floating Doppler Wind Lidar motion simulator for horizontal wind speed measurement error assessment

  • Salcedo Bosch, Andreu
  • Farré Guarné, Joan
  • Sala Álvarez, José
  • Villares Piera, Nemesio Javier
  • Tanamachi, Robin
  • Rocadenbosch Burillo, Francisco
This study presents a wind retrieval simulator of a floating Doppler Wind Lidar (DWL) with 6 Degrees of Freedom (DoF) motion. The simulator considers a continuous-wave conical-scanning floating DWL which retrieves the wind vector from 50 radial velocities per scan. The 6 DoF motion framework as well as the most important buoy motion equations are summarized. Rotational and translational motion effects over HWS measurements are studied parametrically., This work was supported via Spanish Government–European Regional Development Funds project PGC2018-094132-B-I00 and H2020 ACTRIS- IMP (GA-871115). The European Institute of Innovation and Technology (EIT), KIC InnoEnergy project NEPTUNE (Offshore Metocean Data Measuring Equipment and Wind, Wave and Current Analysis and Forecasting Software, call FP7) supported measurements campaigns. CommSensLab is a María-de-Maeztu Unit of Excellence funded by the Agencia Estatal de Investigación (Spanish National Science Foundation). The work of Andreu Salcedo was supported by the “Agència de Gestió d’Adjuts Universitaris i de la Recerca (AGAUR)”, Generalitat de Catalunya, under Grant no. 2020 FISDU 00455., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Analysis of atmospheric aerosol properties using lidar measurements and their impact on radiative budget in Barcelona over the past 20 years

  • Lolli, Simone
  • Sicard, Michaël
  • Comerón Tejero, Adolfo
  • Gil Díaz, Cristina
  • Oliveira, Daniel Camilo Fortunato dos Santos
  • Landi, Tony C.
  • Rodríguez Gómez, Alejandro Antonio
  • Muñoz Porcar, Constantino
  • Rocadenbosch Burillo, Francisco
  • Dios Otín, Víctor Federico
Aerosols are significant atmospheric constituents that modulate radiation and cloud processes. We evaluated 17-year aerosol profile trends in Barcelona, Spain, from lidar measurements. In summer aerosol reaches 5 km, while in the other seasons it exhibits clear exponential decay. Sahara dust transport affects all seasons, with winter layers above and others penetrating the boundary layer. This study informs the formation of haze and urban preservation strategies in the Mediterranean. The analysis puts in evidence that the averaged net radiative effect is of cooling at both surface level and top of the atmosphere., This work has been made possible through the efforts of many people, whom it would be too long to mention, and the funding of many grants through the years, in particular European projects of different framework programmes (FP5 EARLINET project (ID EVR1-CT-1999-40003), FP6 EARLINET-ASOS (ID: 25991), FP7 ACTRIS (ID: 262254), H2020 ACTRIS-2 (ID: 654109), ACTRIS-PPP (ID: 739530), ACTRIS IMP (ID: 871115) and ATMO-ACCESS (ID: 101008004)), projects of the Spanish National Research Programmes (refs. TIC 431/93, AMB96-1144-C02-01, REN2000-1907-CE, REN2000-1754-C02-02 / CLI, REN2003-09753-C02-C02 / CLI, REN2003-09753-C02-C CGL2008- 01330-E/CLI 02 / CLI, REN2002-12784-E, CGL2005-5131-E, CGL2006-27108-E/CLI, CGL2006-26149-E/CLI, CGL2007-28871-/CLI, CTM2006-27154-E/TECNO, TEC2006-07850/TCM, TEC2009-09106, TEC2012-34575, TEC2015-63832-P and PID2019-103886RB-I00), the project of the Catalan Regional Government IMMPACTE, and the ESA project No. nº 21487/08/NL/HE. The support of the European Union through NextGenerationEU funds is also gratefully acknowledged., Peer Reviewed, Postprint (author's final draft)