Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Practical Study of the Temperature Effect in Soil Moisture Measurements

  • García-Navas, José Luis
  • Parra-Boronat, Mar
  • Parra-Boronat, Lorena
  • Rocher, Javier|||0000-0003-0182-1671
  • Sendra, Sandra|||0000-0001-9556-9088
  • Lloret, Jaime|||0000-0002-0862-0533
[EN] Precision agriculture is a current tendency whose goal is to increase the crop production while reducing the water and fertilization use. The use of low cost sensors and Wireless Sensor Networks (WSNs) are frequently used to implement complex systems to control the irrigation process in crops. Taking into account the importance of developing these low cost systems, in this paper we present a practical study that compares a commercial soil moisture sensor with the prototype of our inductive soil moisture sensor, which is based on two solenoid coils. Additionally, we measure its performance as a function of the soil temperature to quantify the effect of this parameter in the sensor measurements. The results show that the temperature greatly affects the sensors measurements and, although our sensor could be used to measure the soil moisture as a function of the temperature, the configuration of two solenoids is not the most suitable to perform this kind of measurements, This work has been partially supported by the European Union through the ERANETMED (Euromediterranean Cooperation through ERANET joint activities and beyond) project ERANETMED3-227 SMARTWATIR by the Ministerio de Educación, Cultura y Deporte, through the Ayudas para contratación predoctoral de Formación del Profesorado Universitario FPU (Convocatoria 2016). Grant number FPU16/05540.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Using HTML5 for M-Learning Environments

  • Sendra, Sandra|||0000-0001-9556-9088
  • Lloret, Jaime|||0000-0002-0862-0533
  • Túnez-Murcia, Ana Isabel
  • García, Laura
[EN] Currently, there are several remote learning platforms based on video streaming. In most situations, these multimedia resources are displayed using smartphones that can be wirelessly connected to networks with deficient capabilities. In this scenario, the levels of Quality of Service (QoS) and Quality of Experience (QoE) perceived by users can be very low. Therefore, with the aim of finding the most efficient combination of Web browsers, codecs and containers, this paper presents a study to analyze how the encoding used in videos can affect the network performance in terms of data transfer rate, transmission delays, transmission errors and throughput. The tests are performed using mobile devices with Android as the operating system. Different Web browsers, containers and codecs supported by HyperText Markup Language V.5 (HTML5) are also included in this study. The browsers used in this study are Google Chrome, Firefox and Opera while the containers considered to carry out our tests are MP4 and WebM. Results show that MP4 could be a good option to transmit high resolution videos while WebM would be the best option for low quality videos., This work has been partially supported by the European Union through the ERANETMED (Euromediterranean Cooperation through ERANET joint activities and beyond) project ERANETMED3-227 SMARTWATIR, by the ¿Ministerio de Economia, Industria y Competitividad¿, through the ¿Convocatoria 2016 - Proyectos I+D+I - Programa Estatal De Investigación, Desarrollo e Innovación Orientada a los retos de la sociedad¿ (Project TEC2016- 76795-C6-4-R), through the ¿Convocatoria 2017 - Proyectos I+D+I - Programa Estatal de Investigación, Desarrollo e Innovación, convocatoria excelencia¿ (Project TIN2017- 84802-C2-1-P) and by the ¿Ministerio de Ciencia, Innovación y Universidades¿ through the ¿Ayudas para la adquisición de equipamiento científico-técnico, Subprograma estatal de infraestructuras de investigación y equipamiento científico-técnico (plan Estatal I+D+i 2017- 2020)¿ (project EQC2018-004988-P).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Internet of Underground Things ESP8266 WiFi Coverage Study

  • García, Laura
  • Parra-Boronat, Lorena
  • Abouaissa, Abdelhafid
  • Lorenz, Pascal
  • Jimenez, Jose M.|||0000-0002-3688-7235
  • Lloret, Jaime|||0000-0002-0862-0533
[EN] The Internet of Underground Things (IoUT) is a novel concept regarding Internet of Things (IoT). It could have countless applications, particularly in agriculture as buried devices do not interfere with the machinery. Furthermore, wireless communication among buried and above ground devices would allow a significant cost reduction as wires would not need to be deployed and wires would not be destroyed by machinery or impede the correct performance of the activities performed by the workers of the field. In this paper, we perform a WiFi coverage study of ESP8266 nodes placed both underground and above ground so as to assess the current lack of knowledge in IoUT and the performance of low-cost controller boards for IoUT applications. Tests were performed with ESP8266 nodes buried at depths of 10 cm, 20 cm, 30 cm and 40 cm in a field located in an area of citrus fields. A node programmed as an AP (Access Point) was placed at several distances at a height of 50 cm. Results showed that the coverage was better for the node buried at a depth of 20 cm., This work has been partially supported by the European Union through the ERANETMED (Euromediterranean Cooperation through ERANET joint activities and beyond) project ERANETMED3-227 SMARTWATIR and by the European Union with the Fondo Europeo Agrícola de Desarrollo Rural (FEADER) Europa invierte en zonas rurales¿, the MAPAMA, and Comunidad de Madrid with the IMIDRA, under the mark of the PDR-CM 2014-2020 project number PDR18-XEROCESPED.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Development of Inductive Sensor for Control Gate Opening of an Agricultural Irrigation System

  • Basterrechea-Chertudi, Daniel Andoni
  • Parra-Boronat, Lorena
  • Rocher, Javier|||0000-0003-0182-1671
  • Lloret, Jaime|||0000-0002-0862-0533
[EN] The monitoring of water level in the agriculture irrigation channels is essential to control the opening gates of these channels. In this way, WSNs (Wireless Sensor Networks) have high relevance to obtain this kind of data. In this paper, we propose a sensor to measure the depth changes in irrigation channels to control the gates opening. It is connected to an Adafruit Feather HUZZAH based on ESP8266, which allows us to build a mobile edge computing system. The developed sensor is based on two coils. Sinus-wave powers the first one, and the second is induced. The coils are winding over a polyvinyl chloride (PVC) that has high resistance for corrosion and low price. Besides, we use copper wire as a conductive metal. We test two different configurations of coils. P1 has five spires for the powered coil (PC) and ten spires for the induced coil (IC). On the other hand, P2 has 40 spires for the PC and 80 spires for the IC. The two prototypes were coiled in one layer. Then, both sensors are tested using a glass bottle where the water column increased with the target to obtain the information of the depth. In both prototypes, the difference of voltage between the maximum and minimum studied depths is more or less the same, 4.46V for P1 and 4.44V for P2. Nevertheless, during the stabilization test, the P1 showed better adaptation for the turbulences than the P2. The P1 shows an oscillation of 0.48V, where the P2 has a maximum fluctuation of 3.2V., This work has been partially supported by European Union through the ERANETMED (Euromediterranean Cooperation through ERANET joint activities and beyond) project ERANETMED3-227 SMARTWATIR by the Conselleria de Educacion, Cultura y Deporte with the Subvenciones para la contratacion de personal investigador en fase postdoctoral, grant number APOSTD/2019/04, and through the "Ayudas para contratacion predoctoral de Formacion del Profesorado Universitario FPU (Convocatoria 2016)". Grant number FPU16/05540.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Quantifying the Production of Fruit-Bearing Trees Using Image Processing Techniques

  • García, Laura
  • Parra-Boronat, Lorena
  • Basterrechea-Chertudi, Daniel Andoni
  • Parra-Boronat, Mar
  • García-Navas, José Luis
  • Lorenz, Pascal
  • Abouaissa, Abdelhafid
  • Jimenez, Jose M.|||0000-0002-3688-7235
  • Rocher, Javier|||0000-0003-0182-1671
  • Sendra, Sandra|||0000-0001-9556-9088
  • Lloret, Jaime|||0000-0002-0862-0533
  • Tomás Gironés, Jesús|||0000-0002-0358-0325
  • Rodilla, M|||0000-0001-6767-5676
  • Falco, S.|||0000-0002-8679-9153
  • Sebastiá-Frasquet, M.-T.|||0000-0002-8042-5628
  • Mengual Cuquerella, Jesús|||0000-0002-8507-509X
  • González Romero, Juan Andrés|||0000-0001-9986-9854
  • Roig-Merino, Bernat|||0000-0002-1437-7752
[EN] In recent years, the growth rate of world agricultural production and crop yields have decreased. Crop irrigation becomes essential in very dry areas and where rainfall is scarce, as in Egypt. Persimmon needs low humidity to obtain an optimal crop. This article proposes the monitoring of its performance, in order to regulate the amount of water needed for each tree at any time. In our work we present a technique that consists of obtaining images of some of the trees with fruit, which are subsequently treated, to obtain reliable harvest data. This technique allows us to have control and predictions of the harvest. Also, we present the results obtained in a first trial, through which we demonstrate the feasibility of using the system to meet the objectives set. We use 5 different trees in our experiment. Their fruit production is different (between 20 and 47kg of fruit). The correlation coefficient of the obtained regression model is 0.97., This work has been partially supported by European Union through the ERANETMED (Euromediterranean Cooperation through ERANET joint activities and beyond) project ERANETMED3-227 SMARTWATIR by the Conselleria de Educación, Cultura y Deporte with the Subvenciones para la contratación de personal investigador en fase postdoctoral, grant number APOSTD/2019/04, and by the Cooperativa Agrícola Sant Bernat Coop.V.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

WiFi and LoRa Energy Consumption Comparison in IoT ESP 32/ SX1278 Devices

  • García, Laura
  • Lorenz, Pascal
  • Jimenez, Jose M.|||0000-0002-3688-7235
  • Lloret, Jaime|||0000-0002-0862-0533
[EN] The use of Internet of Things (IoT) devices has spread through many different fields. Transport, health, and energy management of farming are some of the areas where IoT systems are being utilized. The selection of the wireless communication technology for the IoT system is paramount for its optimal performance. However, factors such as desired coverage or energy consumption must be considered for this selection. In this paper, several tests to determine the battery life that can be obtained after performing WiFi and LoRa Low Power Wide Area Networks (LPWAN) transmissions with a low-cost IoT device has been performed. With a 5 second transmission interval and default settings, similar results were obtained for both WiFi and LoRa. Furthermore, WiFi outperformed LoRa with the default settings and a 30 second transmission interval. Lastly, LoRa did outperform WiFi when the settings where changed so as the transmission power of LoRa was that of 10 dBm., This work has been supported by European Union through the ERANETMED (Euromediterranean Cooperation through ERANET joint activities and beyond) project ERANETMED3-227 SMARTWATIR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Testing Existing Prototypes of Conductivity Sensors for Monitoring the Concentration of Organic Fertilizers in Fertigation Systems

  • Basterrechea-Chertudi, Daniel Andoni
  • Parra-Boronat, Lorena
  • Rocher, Javier|||0000-0003-0182-1671
  • Lloret, Jaime|||0000-0002-0862-0533
[EN] Agricultural production has grown in recent years, increasing the use of Organic Fertilizers (OF). For that reason, the use of these compounds must be controlled in fertigation water. In this paper, we test three prototypes, using different combinations of coils, to determine the amount of OF in the water. A coil is powered by a sine wave of 3.3 peak-to-peak Volts for inducing another coil. The objective of this system is to detect different kinds of problems that can cause incorrect fertilization, which affects the sustainability of agriculture. We present the tests to verify the proper functioning of the prototypes. We test our prototypes by means of different dilutions of OF. The used concentrations of OF are between 0 and 20 g/l. We measure the conductivity for each concentration and the output voltage of our prototypes. The results show that prototype 3 is the one that has the best performance, obtaining 1.47 V of difference between the maximum and minimum output voltage and a good correlation coefficient. Finally, a verification test is carried out; the average error in the different samples tested is 0.2212%., This work has been partially supported by the European Union through the ERANETMED (Euromediterranean Cooperation through ERANET joint activities and beyond) project ERANETMED3-227 SMARTWATIR, by ¿Ministerio de Educación, Cultura y Deporte¿, through the ¿Ayudas para contratacion pre-doctoral de Formación del Profesorado Universitario FPU (Convocatoria 2016)¿. Grant number FPU16/05540, and by Conselleria de Educación, Cultura y Deporte with the Subvenciones para la contratación de personal investigador en fase postdoctoral, grant number APOSTD/2019/04.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Ceratophyllum demersum L. as Phytoindicator and Potential Phytoremediator of Lead Under Hydroponic Conditions

  • Fawzy, Manal
  • El-Khatib, Ahmed
  • Badr, Nadia
  • Abo-El-Kasem, Amany
  • Basterrechea-Chertudi, Daniel Andoni
  • Rocher, Javier|||0000-0003-0182-1671
[EN] The contamination of water by heavy metals like Pb is a huge problem for the environment. In this paper, we test Ceratophyllum demersum L. plants as phytoindicator. These were exposed to different concentrations of Pb for 1¿21 days, under hydroponic conditions, where they exhibited both adsorption and absorption efficiency. These efficiencies influenced in concentration and duration in a dependent manner. For the three initial treatments 0.125, 0.250, 0.500 ¿g/ml, the values of regression coefficients described the occurred variance on the rapid decrease in the Pb concentration in the hydroponic media, reflecting highest removal efficiency by C. demersum. Significant variation (P< 0.05) was recorded between the concentration of Pb accumulated in C. demersum at 0.125 and 0.250 ¿g/ml, while a highly significant value (P< 0.01) was recorded between them at 0.500 ¿g/ml. The regression coefficient denotes the pronounced impact of treatment concentration on the accumulation rate (R^2 = 0.9987). The adsorption efficiency of C. demersum appeared to be influenced by the Pb hydroponic media concentration, where after 21 days, the higher Pb adsorption was recorded at 0.125 ¿g/ml and the lowest one was obtained at 0.500 ¿g/ml. Results suggest that plants responded positively to the increase of Pb concentrations and they accumulated a high amount of metal. Due to metal removal coupled with detoxification potential, the plant appears to have potential for its use as phytoremediator species in aquatic environments., This work has been partially supported by the European Union through the ERANETMED (Euromediterranean Cooperation through ERANET joint activities and beyond) project ERANETMED3-227 SMARTWATIR by the Ministerio de Educación, Cultura y Deporte, through the Ayudas para contratacion predoctoral de Formación del Profesorado Universitario FPU (Convocatoria 2016). Grant number FPU16/05540.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Low-cost Soil Moisture Sensors Based on Inductive Coils Tested on Different Sorts of Soils

  • Parra-Boronat, Mar
  • Parra-Boronat, Lorena
  • Mauri, Pedro V.
  • Lloret, Jaime|||0000-0002-0862-0533
  • Llinares Palacios, Josep Vicent|||0000-0002-9740-3281
[EN] The use of precision agriculture and the Internet of Things has improved the efficiency of many cultures. Nevertheless, there are a few low-cost options to monitor soil moisture. Moreover, those options depend on the specific characteristics of the soil. In this paper, we attempt to find a sensor, based on mutual inductance, that could be used for more than one sort of soil. We study three prototypes, one of them with casing. The sensors are powered with a voltage of 10 peak to peak volts. One of the soils has a high content of organic matter and sand while the other is rich in sand and silt. The best prototype for the soil with high levels of organic matter has 10 turns on the powered coil and 5 on the induced coil. The best frequency for this sensor is 1340 kHz. For the soil with a significant quantity of silt, the best prototype has 80 turns on the powered coil and 40 on the induced coil. The frequency at which this sensor works best is 229 kHz, which happens to be its peak frequency. With those characteristics regressions lines with R2 values higher than 0.75 can be modeled, This work is partially found by the Conselleria de Educación, Cultura y Deporte with the Subvenciones para la contratación de personal investigador en fase postdoctoral, grant number APOSTD/2019/04, by European Union through the ERANETMED (Euromediterranean Cooperation through ERANET joint activities and beyond) project ERANETMED3-227 SMARTWATIR, and by the European Union with the Fondo Europeo Agrícola de Desarrollo Rural (FEADER) Europa invierte en zonas rurales, the MAPAMA, and Comunidad de Madrid with the IMIDRA, under the mark of the PDR-CM 2014-2020 project number PDR18-XEROCESPED.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Collaborative LoRa-Based Sensor Network for Pollution Monitoring in Smart Cities

  • Sendra, Sandra|||0000-0001-9556-9088
  • Lloret, Jaime|||0000-0002-0862-0533
  • García-Navas, José Luis
  • Romero-Diaz, Pablo
[EN] With the aging of the car park in big cities, together with the fact that the number of users of private vehicles is increasing, the quality of air (QoA) in large cities has been worryingly reduced. Therefore, it is becoming increasingly necessary to implement new monitoring infrastructures to improve our smart cities. Therefore, in this paper, we present a collaborative Long Range (LoRa)-based sensor network for pollution monitoring in smart cities. The system is based on geo-located nodes capable of measuring the temperature, relative humidity and concentration of CO2 in urban environments. The system also takes into account the subjective opinions of citizens. By using the collected data and considering the restrictions policies of the city, the system in able to send the required orders to panels and traffic signs to control de traffic circulation. Finally, the citizens can be advised to avoid going to too polluted areas. The system has been testes in a real environment with very interesting results., This work has been partially supported by the European Union through the ERANETMED (Euromediterranean Cooperation through ERANET joint activities and beyond) project ERANETMED3-227 SMARTWATIR, by the Ministerio de Economia, Industria y Competitividad, through the Convocatoria 2016 - Proyectos I+D+I - Programa Estatal De Investigación, Desarrollo e Innovación Orientada a los retos de la sociedad (Project TEC2016- 76795-C6-4-R), by the Ministerio de Ciencia, Innovación y Universidades through the Ayudas para la adquisición de equipamiento científico-técnico, Subprograma estatal de infraestructuras de investigación y equipamiento científicotécnico (plan Estatal I+D+i 2017-2020) (project EQC2018- 004988-P) and through the Research Contracts of Youth Employment of the University of Granada, through its operative program of Youth Guarantee of the Regional Government of Andalusia and the European Social Fund.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Water Conductivity Sensor based on Coils to Detect Illegal Dumpings in Smart Cities

  • Rocher, Javier|||0000-0003-0182-1671
  • Lloret, Jaime|||0000-0002-0862-0533
  • Basterrechea-Chertudi, Daniel Andoni
  • Taha, Miran
  • Parra-Boronat, Mar
[EN] The illegal dumpings in sewerage can cause problems in the Wastewater treatment plants. In this paper, we propose a system for detecting these illegal dumpings. We use conductivity sensor for detecting the change in the conductivity of water. Because this change may be due to a dump. The system is based on two coils, a coil is powered by a sinus-wave and induced the other coil. To prevent damaged for water in the copper we encapsulate the coils in a PVC tube. These coils are connected to flyport to send the values and generate alarms. We test with different configurations of coils with encapsulation of 3 and 1 mm. In the different prototypes tested have been seen that with the 3 mm encapsulation no significant differences are observed. The better prototypes are based on 40 spires of the powered coil and 80 spires in the induced coil. The best difference between samples of 0 and 40 g/l of table salt are in the prototype when the spires are distributed in 1 layer (6.06 V). Another prototype test with the same number of turns but distributed in 4 layers has a difference of 4.10 V. But during the verification phase we verified that this last prototype presents a relative error of 2.54% compared to 6.55% of the prototype distributed in a layer, This work has also been partially supported by the European Union through the ERANETMED (Euromediterranean Cooperation through ERANET joint activ-ities and beyond) project ERANETMED3-227 SMARTWATIR by the Ministerio de Educación, Cultura y Deporte, through the Ayudas para contratacion predoctoral de Formación del Profesorado Universitario FPU (Convocatoria 2016). Grant number FPU16/05540.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

A WSN-based monitoring system to control Sewerage

  • Rocher, Javier|||0000-0003-0182-1671
  • Romero Martínez, José Oscar|||0000-0003-4081-9005
  • Lloret, Jaime|||0000-0002-0862-0533
  • García-Navas, José Luis
[EN] The sewerage is a critical infrastructure in cities because of the drainage of the urban runoff and the evacuation of the wastewater. Two types of sewerage, separated sewerage and combined sewerage, can be differentiated. In this paper, we show the application of a level sensor and a rain sensor for monitoring the separated sewerage. The level sensor is used for knowing if there is a critical level of water in the sewerage. The rain sensor is used to know if it is raining. The combination of this information allows the identification of three scenarios. These scenarios are normal situation, low drainage and illicit discharge/blockages in the pipeline. In addition, we study the use of sensors and mathematical models for monitoring the velocity of the wastewater. We concluded that the use of mathematical models is a good option for monitoring the velocity. Because with exception of the thermal sensors the other types of sensors show important gaps. The velocity is used to estimate the flow that is dumping in the water bodies. We use an ESP32 board program with Arduino IDE for data collection and sending the data to a server on the same network via Wi-Fi. The server is a computer that processes the data. We present the programming code and the ports that should be used for transmitting the data from Arduino to computer server., Supported by European Union through the project ERANETMED3-227 SMARTWATIR by the Ministerio de Educación, Cultura y Deporte. Grant number FPU16/05540