Skip to main content

NUEVO PROCESO DE CHEMICAL LOOPING PARA OBTENCION DE CO A PARTIR DE CO2 E H2 VERDE COMO RUTA PARA LA PRODUCCION DE BIOCOMBUSTIBLES PARA AVIACION

PID2020-113131RB-I00

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Call year 2020
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Comparison of low-cost and synthetic oxygen carriers for the Biomass Chemical Looping Gasification process

  • Samprón, Iván
  • Condori, Óscar
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Izquierdo Pantoja, María Teresa
5 figures, 2 tables.-- Talk delivered at the 24th International Conference on Fluidized Bed Conversion, FBC24, at Chalmers University of Technology, in Gothenburg (Sweden)., Biomass Chemical Looping Gasification (BCLG) is a novel technology which permits the production of high purity, N2-free renewable syngas. In this work, the behavior of seven oxygen carriers, 4 low-cost (3 ores, and 1 waste) and 3 synthetic materials, was compared during continuous operation in a 1.5 kWth BCLG unit. For that, oxygen-to-fuel ratio (λ) and fuel reactor (FR) temperature were varied in a wide range of operating conditions. High carbon conversion, ηcc (> 95 %) and fuel conversion, Xb, (> 85%) were found for all the oxygen carriers. The same trends in the syngas composition were observed with low-cost and synthetic oxygen carriers when the λ and FR temperature were varied. However, the amount of syngas generated was higher for synthetic oxygen carriers due to their catalytic effect on CH4 conversion. In addition, tar concentration in the generated syngas was lower using synthetic oxygen carriers than with low-cost materials and these concentrations decreased with increasing FR temperature. Finally, lifetime values between 100 h and 900 h were determined for all the oxygen carriers, being the best ilmenite (600 h) among the low-cost materials and Fe10Al (900) among the synthetic ones., This work was supported by the CO2SPLIT project, Grant PID2020-113131RB-I00, funded by MICIN/AEI/10.13039/501100011033, and by the European Union´s Horizon 2020-Research and Innovation Framework Programme under grant agreement No 817841 (CLARA). I. Samprón thanks the Spanish Ministerio de Ciencia, Innovación y Universidades (MICIU) for the PRE-086217 pre-doctoral fellowship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Techno-economic analysis of chemical looping processes with biomass resources for energy production and CO2 utilization

  • Cabello Flores, Arturo
  • Abad Secades, Alberto
  • Obras-Loscertales, Margarita de las
  • Domingos, Yldeney
  • Mendiara, Teresa
4 figures, 7 tables.-- Work presented at 37th International Conference on Efficiency, Cost, Optimization, Simulation and Environmental Impact of Energy Systems, held on 30th June - 4th July, 2024, in Rhodes (Greece)., Bioenergy coupled with carbon capture utilization and storage (BECCUS) is an attractive greenhouse gas mitigation technology that can produce negative CO2 emissions by combining bioenergy resources with the utilization or geological storage of the captured CO2. The main objective of this work was to evaluate the technical and economic feasibility of two BECCUS technologies based on chemical looping concept with two biomass waste as fuels, i.e., swine manure and pine sawdust, for the production of thermal energy and a pure CO2 stream that is subsequently used as raw material in agricultural greenhouses. Direct use of solid biomass resources was considered for the Chemical Looping with Oxygen Uncoupling (CLOU) option, whereas biogas production was the starting point for Chemical Looping Combustion (CLC). The profitability of the chemical looping scenarios was assessed through the Levelized Cost of CO2 (LCOCO2). This parameter was estimated at 218.31 €/t CO2 for the CLC scenario, a value much higher than those for the CLOU scenarios (73.04 - 87.32 €/t CO2) due to the limited conversion degree of the carbon present in the fuel waste to biogas and the need for an additional experimental plant to the CLC unit, i.e., the biogas production plant. Comparing the CLOU scenarios, the economic analysis revealed that the profitability of the biomass-fueled chemical looping facility was markedly sensitive to the selling price of the biomass resource. Furthermore, the values of the LCOCO2 parameter for the CLOU scenarios were lower than those estimated in other research studies that implemented BECCUS technologies and utilized the captured CO2 for identical purposes. Therefore, it can be concluded that CLOU processes fed with biomass are a very attractive BECCUS technology for heat generation where, in addition, the pure CO2 stream obtained at the outlet of the fuel reactor can be considered a marketable, high value-added product., This work was supported by the UPCLOU project (Grant PDC2021-121190-I00 funded by MCIN/AEI /10.13039/501100011033 and by European Union Next GenerationEU/PRTR) and the CO2SPLIT project (Grant PID2020-113131RB-I00/ AEI/10.13039/501100011033). A. Cabello is also grateful for Grant IJC2019-038908-I funded by MCIN/AEI/10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Selection of materials and proof of concept for CO2 Splitting process

  • García Domínguez, Alberto O.
  • Cabello Flores, Arturo
  • García Labiano, Francisco
  • Izquierdo Pantoja, María Teresa
  • Diego Poza, Luis F. de
8 figures 2 tables.-- Work presented at the 7th International Conference on Chemical Looping, September 29 – October 2, 2024, Banff, Alberta, Canada, The transition from fossil fuels to renewable energy sources and from a carbon-based economy to a hydrogen-based economy brings with it a major drawback: the energy density of fuel decreases. This fact is very important for sectors such as aviation, which depends on fuels with high energy density. Therefore, to reduce CO2 emissions in the aviation sector, the best short-term solution is to replace fossil aviation kerosene with alternative fuels such as bio-kerosene. However, today, synthetic kerosene production suffers from low process efficiency and high costs. To address this problem, trying to significantly increase efficiency and reduce costs, a new Chemical Looping process (CLCO2SPLIT) is being implemented to obtain CO from CO2 and green H2 as a route for the production of aviation biofuels through the Fischer-Tropsch (F-T) synthesis process. The principle of the CLCO2SPLIT process is similar to the well-known Chemical Looping Combustion (CLC) process, but the CLCO2SPLIT process uses three reactors instead of two. The development of suitable oxygen carriers is one of the key aspects for the proof-of-concept of the CLCO2SPLIT process. Therefore, the main objective of this work was to carry out a preliminary screening of a wide variety of materials based on iron oxide, both synthetic and mineral, evaluating their physicochemical properties (mechanical resistance, tendency to agglomeration, chemical stability, reactivity and redox conversion) by means of crushing strength tests, thermogravimetric analyses, and redox cycles in a batch fluidized bed reactor. It was found that the best candidates for the process were the synthetic Fe-based oxygen carriers prepared using Zr-doped hydrotalcite, SiO2:ZrO2 (50:50), and Mg-doped ZrO2 as supports., This work was supported by the CO2SPLIT Project, Grant PID2020-113131RB-I00, funded by MICIN/AEI/10.13039/501100011033. A.O. García-Domínguez thanks to MICIN and FSE+ the PRE2021-098211 predoctoral fellowship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Life cycle assessment of power-to-methane systems with CO2 supplied by the chemical looping combustion of biomass

  • Navajas, A.
  • Mendiara, Teresa
  • Gandía, L. M.
  • Abad Secades, Alberto
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
6 figures, 2 tables.-- Work presented at the 6th International Conference on Chemical Looping, 19-22 September 2022, Zaragoza, Spain., Power-to-methane (PtM) systems may allow mitigating the fluctuations in renewable energy supply by storing the energy in the form of methane. In these systems, hydrogen produced by electrolysis is combined with carbon dioxide from different sources to produce methane through Sabatier reaction. The present work analyzes PtM systems based on CO2 supply from Chemical Looping Combustion (CLC) units running on biomass (PtM-bioCLC). Life-cycle-assessment of PtM- bioCLC systems was done to evaluate their environmental impact respect a specific reference case. It was concluded that the configurations proposed have the potential to decrease the value of the climate change indicator, the global warming potential (GWP), to the lowest values reported to date in literature. Moreover, the possibility to effectively remove CO2 from the atmosphere realizing the concept of CO2 negative emissions was also demonstrated. Besides GWP, up to 16 LCA indicators were also evaluated and their values for the PtM-bioCLC systems analyzed were similar to those found in the reference case or even significantly lower in some of the categories such as resource use/depletion (RUE), ozone depletion (POF), human health (RI), acidification (AC) and eutrophication (EUT and EUM). Results obtained highlight the potential of these newly proposed PtM schemes., This work was supported by Grant PDC2021-121190-I00 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR and also by Grant PID2020-113131RB-I00 funded by MICIN/AEI/10.13039/501100011033. A.N. and L.M.G. gratefully acknowledge Grant RTI2018-096294-B-C31 funded by MCIN/AEI/10.13039/501100011033 and “ERDF A way of making Europe”, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Behaviour of oxygen carriers under siloxanes containing biogas during chemical looping combustion operation

  • Izquierdo Pantoja, María Teresa
  • Mendiara, Teresa
  • Cabello Flores, Arturo
  • Abad Secades, Alberto
  • Mattisson, Tobias
  • Adánez Elorza, Juan
3 figures, 4 tables.-- Work presented at the Fluidized Bed Conversion Conference - FBC2024, 8-11th May 2022, Chalmers University of Technology (Sweden)., Biogas is mostly composed by CH4 and CO2 generated in the anaerobic digestion of organic matter. However, other compounds present in lower amounts should be also taken into consideration during biogas exploitation since they may cause operational problems. This is the case of siloxanes, which decompose at high temperature generating silicates and SiO2, causing abrasion and leading to the failure of equipment. Thus, biogas cleaning and upgrading constitutes the key challenge of the biogas supply chain. Chemical Looping Combustion (CLC) would allow direct use of biogas without prior cleaning, with significant energy and economic advantages. In CLC, the oxygen required for combustion is supplied by an oxygen carrier (metal oxide) that circulates between two reactors. In the reduction reactor, the fuel is supplied and oxidized to CO2 and H2O while the oxygen carrier is reduced. In the oxidation reactor, the reduced oxygen carrier is re-oxidized in air. Thus, CO2 capture is intrinsic to the process. The objective of the present work was to analyse the possible effects of siloxanes in biogas CLC processes by studying the reactivity and physicochemical changes of selected oxygen carriers during combustion in a batch fluidized bed reactor. Two representative oxygen carriers based on CuO and Fe2O3 were chosen considering the high reactivity in the combustion of methane of Cu-based oxygen carriers and the resistance to sulphur deactivation of Fe-based oxygen carriers. Hexamethyldisiloxane (L2) was selected as siloxane model compound. It was found that siloxane decompose to produce a gaseous fraction and Si-based particles that interact with the oxygen carrier. Part of the Si in these particles was concentrated in the surface of the oxygen carrier particles in the form of SiO2 and silicates/aluminosilicates. This may have some implications on the reactivity of the carriers and their fluidization properties; however, no operation problems would be expected for the oxygen carriers tested in this work in a continuous combustion CLC unit operated with real siloxane concentration., This work was supported by the European Regional Development Fund (ERDF) under the program "Programa Operativo FEDER Aragón 2014-2020 - Construyendo Europa desde Aragón. Proyecto BiosinCO2 (LMP180_18), and by the CO2SPLIT project, Grant PID2020-113131RB-I00, funded by MICIN/AEI/10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Biomass chemical looping gasification for syngas production using a copper-based oxygen carrier in a 1.5 kWth unit

  • Samprón, Iván
  • Diego Poza, Luis F. de
  • García Labiano, Francisco
  • Izquierdo Pantoja, María Teresa
  • Cabello Flores, Arturo
9 figures, 3 tables.-- Work presented at 6th International Conference on Chemical Looping, 19-22 September 2022, Zaragoza, Spain., Biomass Chemical Looping Gasification (BCLG) is a novelty technology which enables the production of renewable syngas without the need for external power supply and achieving negative carbon emissions. In this work, the behavior a synthetic Cu-based (14 wt% CuO) oxygen carrier, Cu14Al_ICB, was tested during 45 h in a 1.5 kWth continuous unit using pine sawdust as fuel. The effect of oxygen-to- fuel ratio (𝛌) and gasification temperature on syngas composition and gasification parameters, such as fuel conversion, carbon capture, cold gas efficiency, and syngas yield, was studied. The decrease of oxygen-to-fuel ratio increased the concentration of H2 and CO, while the increase in gasification temperature mainly improved char gasification, also promoting H2 and CO generation. High amounts of syngas with low CH4 concentrations (~2.3 mol/kg of dry biomass) were obtained at any condition due to the catalytic effect of metallic copper on CH4 reforming reactions. Values of syngas yield close to the obtained with Ni-based solids were achieved. The oxygen carrier also had a high effect on tar removal, reaching tar concentration values similar to those obtained by operating under Chemical Looping Combustion conditions. A particle lifetime of ~8000 h was inferred for this oxygen carrier, which is the highest lifetime obtained so far for an oxygen carrier working under BCLG conditions. In addition, the mechanical properties, reactivity and oxygen transport capacity were maintained during the campaign. Therefore, the Cu14Al_ICB oxygen carrier has proven to be an excellent material for the BCLG process., This work was supported by ENE2017-89473-R AEI/FEDER, UE, and the CO2SPLIT Project, Grant PID2020-113131RB- I00, funded by MICIN/AEI/10.13039/501100011033. Iván Samprón thanks the Spanish Ministerio de Ciencia, Innovación y Universidades (MICIU) for the PRE-086217 predoctoral fellowship. A. Cabello thanks the Grant IJC2019- 038908-I funded by MCIN/AEI/10.13039/501100011033., Peer reviewed