Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Dual functional material based on Ru-alkali metals on alumina for the direct CO2 capture from air and subsequent conversion to CH4

  • García-Bordejé, José Enrique
  • Conesa, José María
  • Guerrero Ruíz, A.R.
  • Rodríguez-Ramos, Inmaculada
Oral communication presented at the ISGC 2025, the world event in sustainable chemistry research & innovation, La Rochelle (France), 12th-16th May 2025., [Introduction] Dual functional materials (DFM) for CO2 capture and conversion combine both processes in one single material and reactor intensifying the process with enhanced mass transport and energy efficiency and avoiding cost of CO2 capture and transport of conventional carbon capture and utilization (CCU) approaches. These materials have been applied to CO2 capture from flue gases at high temperature [1-3]. Recently, CO2 capture directly from air (DAC) is gaining impetus since it has been proposed as one of the technologies leading to negative CO2 emissions [4]. The use of DFM for DAC is very scarce [5] due to the challenging high CO2 dilution and atmospheric temperature and pressure. Herein, bimetallic materials consisting on Ru nanoparticles (3 wt%) and K or Na metals (with different molar ratios) supported on mesoporous alumina have been prepared. The materials have been tested in the capture of CO2 from air at 40 ºC and subsequent conversion to CH4 heating at several temperatures (200ºC-300 ºC) under H2 flow. We have studied the effect of several parameters in the cyclic performance during CO2 capture and conversion such as the effect of the alkaline metal loading, the temperature of the regeneration and the presence of humidity in the air. [Experimental] Bimetallic Ru-Na and Ru-K dual functional materials (DFM) with different ratios have been supported on mesoporous alumina keeping a constant Ru loading of 3 wt% on the DFM. To this end, alkali metal and Ru where impregnated by incipient wetness impregnation and calcination at 500 ºC in Ar and subsequent reduction in H2 at 500 ºC after metal deposition. The DFMs were characterised by TEM, N2 physisorption, XRD, TPR and XPS. Bimetallic Ru-Na and Ru-K dual functional materials (DFM) with different ratios have been supported on mesoporous alumina keeping a constant Ru loading of 3 wt% on the DFM. To this end, alkali metal and Ru where impregnated by incipient wetness impregnation and calcination at 500 ºC in Ar and subsequent reduction in H2 at 500 ºC after metal deposition. The DFMs were characterised by TEM, N2 physisorption, XRD, TPR and XPS. [Results] The amount of CO2 captured from air was calculated by integration of the CO2 breakthrough curve (Figure 1a). Figure 1b shows the gases released in the regeneration heating under 20% H2 flow up to different temperatures. A CO2 peak (discontinuous line) and a CH4 peak (continuous line) are observed. Unconverted CO2 adsorbed in weak basic sites is evolved at the lower temperature range. From 130 ºC on a peak of CH4 evolves. At a regeneration temperature of 200 ºC the maximum is not reached but at 250 ºC the maximum is reached. Therefore, this temperature is considered enough to regenerate the capture sites for a next cycle. The amount of captured CO2 increases with the alkali metal loading up to a ratio (1:10) both for Ru-Na and Ru-K series while for higher alkali loading of (1:14.6) the captured CO2 decreases (Figure 2). The maximum CO2 captured are ~500 µmol g-1 and 400 µmol g-1 for Ru-Na (1:10) and Ru-K (1:10), respectively. In the case of Ru-Na DFM the CO2 production decreases to negligible values for the higher loadings, namely (1:10) and (1:14.6) suggesting that the sites of weakly adsorption of CO2 disappear. In contrast, for the Ru-K series the selectivity to CH4 decreases as the alkali loadings increases. Higher CO2 selectivities decreases CH4 production and increases the subsequent costs of separation. The DFMs show a remarkable CO2 capture capacity, which increases in humid conditions, being competitive and even surpassing other capture materials used in DAC in the literature. In addition, the high selectivity to methane intensifies the process compared to other CCU approaches., The Financial support from Spanish “Agencia Estatal de Investigación” (AEI, project PID2023-146481OB-I00), Gobierno de Aragón (Grupo Reconocido DGA T03_17R) are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Captura de CO2 directa del aire y su conversión en CH4 usando materiales de doble función

  • García-Bordejé, José Enrique
  • Conesa, José María
  • Rodríguez-Ramos, Inmaculada
  • Guerrero Ruíz, A.R.
Resumen del póster presentado en el Congreso de la Sociedad Española de Catálisis (SECAT) en Alcalá de Henares (España), 17-20 de Junio de 2025., Los materiales de doble función (DFM) para la captura y conversión de CO2 combinan ambos procesos usando un sólo material y reactor. De manera que se intensifica el proceso con una transferencia de masa y calor mejoradas. Además, se evitan los costos de presurización y transporte de CO2 generados en los procesos convencionales de captura y utilización (CCU). DFMs se han usado ampliamente para la captura del CO2 de gases de chimenea a altas temperaturas (300-500 ºC) [1-3]. Más recientemente, la captura de CO2 directa del aire (DAC) está ganando interés debido a que se ha propuesto como una tecnología que conduce a emisiones negativas de CO2 [4]. Sin embargo, se han aplicado raramente para DAC [5] debido principalmente a la gran dilución del CO2 y a los altos costos de regeneración. En este trabajo, hemos preparado DFMs basados en un metal alcalino (K o Na) y Ru soportados tanto en alúmina como en grafito de alta superficie. Dichos DFMs se han caracterizado y se ha estudiado la influencia del porcentaje de alcalino y la temperatura de regeneración en ciclos de captura y metanación., The Financial support from MICIU/AEI/10.13039/501100011033 and from FEDER, UE through project PID2023-146481OB-I00 and Gobierno de Aragón (Grupo Reconocido DGA T03_17R) are gratefully acknowledged, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Bifunctional materials for integrated DAC and conversion to methane

  • García-Bordejé, José Enrique
  • Moral Pombo, Jorge
  • Conesa, José María
  • Guerrero Ruíz, A.R.
  • Rodríguez-Ramos, Inmaculada
Abstract of the oral communication presented at the 22nd International Conference on Carbon Dioxide Utilization, 22nd ICCDU, 23rd-27th June, Lisbon (Portugal)., To fight against accelerating climate change and to comply the Paris agreement, neutral or even negative CO2 emissions measures must be urgently implemented such as CO2 capture from diluted sources followed by storage (CCS) or utilization (CCU) [1]. Integrating CO2 capture and conversion into one single process offers several advantages, including avoiding the need for CO2 pressurization and transport to storage or conversion site. The integration also enhances process intensification by improving mass and heat transfer while reducing equipment investment. The intensification is even greater if one single material is used for both capture and catalytic conversion, as the heat and mass transfer distances are nanometric. These materials, known as dual functional materials (DFMs), consist of a CO2 capture component (alkali metal) and a metal catalyst for subsequent methanation. DFMs were firstly introduced by Farrauto et al. [1] and have since then been widely used for capture of CO2 from flue gases at isothermal conditions as the temperature of the emitted gas matches that of methanation reaction [2,3]. DFMs were also proposed for direct air capture (DAC) and subsequent CO2 conversion [4]. However, this application presents several challenges, such as the high dilution of CO2 (400 ppm) and the large volumes of air that must be treated. In previous articles we studied DFMs for the capture of CO2 from flue gases [5,6]. Here we extend the application to DAC [7,8]. To this end, we prepared DFMs consisting of a methanation catalyst (4 wt%Ru) and an alkaline metal (Cs or Ba) to achieve (Cs or Ba)/Ru atomic ratios of 1 and 2, dispersed on a high surface area graphite. DFM were tested in DAC (40ºC) and subsequent methanation (300 ºC) for 25 cycles. At stable cyclic performance, the best performing DFM of each series, RuBa (1:1) and RuCs (1:2), captured 0.1 mmol g-1 and 0.44 mmol g-1, respectively. Based on the characterisation, we attributed this to the higher dispersion of Cs and to the higher stability of the carbonates formed with Ba which are not regenerated completely at 300 ºC., This work was funded by MICIU/AEI/10.13039/501100011033 and by FEDER, UE through grant PID2023-146481OB-I00, Gobierno de Aragón (Grupo Reconocido DGA T03_17R), and associated EU Regional Development Funds., Peer reviewed